Dissolution of Borosilicate Glass in NaCI and MgCI2 Solutions: Implications for Disposal in Rock Salt.
Abstract not provided.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Abstract not provided.
The Saltstone Facility is designed and permitted to immobilize and dispose of low-level radioactive and hazardous liquid waste (salt solution) remaining from the processing of radioactive material at the Savannah River Site. Low-level waste (LLW) streams from the Effluent Treatment Project (ETP), H-Canyon, the DDA (Deliquification, Dissolution, and Adjustment) process, and the decontaminated salt solution product from the Actinide Removal Process/Modular Caustic Side Solvent Extraction (CSSX) Unit (ARP/MCU) process are stored in Tank 50 until the LLW can be transferred to the Saltstone Facility for treatment and disposal. The LLW must meet the specified waste acceptance criteria (WAC) before it is processed into saltstone. The specific chemical and radionuclide contaminants and their respective WAC limits are listed in the current Saltstone WAC. Waste Solidification Engineering (WSE) requested that Savannah River National Laboratory (SRNL) perform quarterly analysis on saltstone samples. The concentrations of chemical and radionuclide contaminants are measured to ensure the saltstone produced during each quarter is in compliance with the current WAC. This report documents the concentrations of chemical and radionuclide contaminants for the 2011 Second Quarter samples collected from Tank 50 on April 4, 2011 and discusses those results in further detail than the previously issued results report. The following conclusions are drawn from the analytical results provided in this report: (1) The concentrations of the reported chemical and radioactive contaminants were less than their respective WAC targets or limits unless noted in this section. (2) The reported detection limit for {sup 59}Ni is above the requested limit from Reference 2 but below the established limit in Reference 3. (3) The reported detection limit for {sup 94}Nb is above the requested limit from Reference 2; however, it is below the established limits in Reference 3. (4) The reported concentration of {sup 242m}Am is above the target in Listed in Attachment 8.4 of the Saltstone WAC. (5) {sup 247}Cm and {sup 249}Cf are above the requested limits from Reference 2. However, they are below the limits established in Reference 3. (6) The reported detection limit for Norpar 13{sup 5} is greater than the limit from Table 4 and Attachment 8.2 of the WAC. (7) The reported detection limit for Isopar L is greater than the limit from Table 3 of the WAC. (8) Isopar L and Norpar 13 have limited solubility in aqueous solutions making it difficult to obtain consistent and reliable sub-samples. The values reported in this memo are the concentrations in the sub-sample as detected by the instrument; however, the results may not accurately represent the concentrations of the analytes in Tank 50.
Dual-ion batteries are known for anion storage in the cathode coupled to cation incorporation in the anode. We flip the sequence of the anion/cation-storage chemistries of the anode and the cathode in dual-ion batteries (DIBs) by allowing the anode to take in anions and a cation-deficient cathode to host cations, thus operating as a reverse dual-ion battery (RDIB). The anion-insertion anode is a nano-composite having ferrocene encapsulated inside a micro-porous carbon, and the cathode is a Zn-insertion Prussian blue, Zn-3[Fe(CN)(6)](2). This unique battery configuration benefits from the usage of a 30 m ZnCl2 "water-in-salt" electrolyte. This electrolyte minimizes the dissolution of ferrocene; it raises the cation-insertion potential in the cathode, and it depresses the anion-insertion potential in the anode, thus widening the full cell's voltage by 0.35 V compared with a dilute ZnCl2 electrolyte. RDIBs provide a configuration-based solution to exploit the practicality of cation-deficient cathode materials in aqueous electrolytes.
The Saltstone Facility is designed and permitted to immobilize and dispose of low-level radioactive and hazardous liquid waste (salt solution) remaining from the processing of radioactive material at the Savannah River Site. Low-level waste (LLW) streams from the Effluent Treatment Project (ETP), H-Canyon, the DDA (Deliquification, Dissolution, and Adjustment) process, and the decontaminated salt solution product from the Actinide Removal Process/Modular Caustic Side Solvent Extraction (CSSX) Unit (ARP/MCU) process are stored in Tank 50 until the LLW can be transferred to the Saltstone Facility for treatment and disposal. The LLW must meet the specified waste acceptance criteria (WAC) before it is processed into saltstone. The specific chemical and radionuclide contaminants and their respective WAC limits are listed in the current Saltstone WAC. SRS Liquid Waste Operations (LWO) requested that Savannah River National Laboratory (SRNL) perform quarterly analysis on saltstone samples. The concentrations of chemical and radionuclide contaminants are measured to ensure the saltstone produced during each quarter is in compliance with the current WAC. This report documents the concentrations of chemical and radionuclide contaminants for the 2009 Fourth Quarter samples collected from Tank 50 on October 2, 2009 and discusses those results in further detail than the previously issued results report. This report details the chemical and radionuclide contaminant results for the characterization of the 2009 Fourth Quarter sampling of Tank 50 for the Saltstone Waste Acceptance Criteria (WAC). Information from this characterization will be used by Liquid Waste Operations (LWO) to support the transfer of low-level aqueous waste from Tank 50 to the Salt Feed Tank in the Saltstone Facility in Z-Area, where the waste will be immobilized. This information is also used to update the Tank 50 Waste Characterization System. The following conclusions are drawn from the analytical results provided in this report: (1) The concentrations of the reported chemical and radioactive contaminants were less than their respective WAC targets or limits unless noted in this section. (2) The reported detection limit for Isopar L is greater than the limit from Table 3 of the WAC. (3) The reported detection limits for {sup 59}Ni and {sup 94}Nb are above the requested limits from Reference 4. However, they are each below the limits established in Reference 3. (4) The reported detection limit for isopropanol is greater than the requested limit from Table 4 of the WAC. (5) The reported detection limits for {sup 247}Cm and {sup 249}Cf are above the requested limits from Reference 4. However, they are below the limits established in Reference 3. (6) Isopar L and Norpar 13 have limited solubility in aqueous solutions making it difficult to obtain consistent and reliable sub-samples. The values reported in this memo are the concentrations in the sub-sample as detected by the GC/MS; however, the results may not accurately represent the concentrations of the analytes in Tank 50.
A novel in-situ corrosion sensor for structural alloys exposed to molten salts has been initially demonstrated. The measurement is based upon observing the change in magnetic susceptibility of salt wetted structural alloys as corrosion occurs. In halide salts corrosion of structural alloys proceeds primarily through dissolution of the least noble component of the alloy into the melt. All currently available structural alloys intended for use with molten salt reactors (MSRs) include nickel, chromium, and iron. Chromium is preferentially oxidized from the alloy surface by exposure to halide salts at high temperature. Diffusion within the alloy results in progressively deeper depletion of chromium from the alloy surface. Relevant chromium bearing structural alloys are paramagnetic. However, once the chromium has been depleted, they become ferromagnetic. Thus, structural alloy corrosion in an MSR results in development of a ferromagnetic surface layer whose depth increases with increasing corrosion. The corrosion sensor functions by employing the progressive increase in ferromagnetism as a transduction mechanism through including the corroding alloy in a magnetic circuit. Development of the sensor remains a work in progress. To date we have characterized the sensor response of structural alloy samples with varying degrees of corrosion at room temperature. Over the next year we plan to demonstrate sensor performance at MSR operating temperatures (up to 750 °C) in a piping geometry.
A mechanistic-based mass accountancy model in the context of liquid-fueled molten salt reactors was implemented in the dynamic systems modeling software library TRANSFORM by way of coupling with the equilibrium thermodynamics code Thermochimica. Liquid-fueled molten salt reactors present new challenges for mass accountancy because of the dissolution of fuel and evolved fission products, which may be soluble in the salt, off-gas, or precipitate. Two cases of mass loss from the molten salt were addressed: off-gassing and precipitation. The software implementation was tested through a series of increasingly complex demonstration problems, culminating in a model of the primary fuel and primary coolant loops of the molten salt demonstration reactor. Analysis shows that negligible mass was lost from the salt under normal operating conditions, but an overheating event caused by partial loss of fuel loop cooling resulted in release of measurable amounts of uranium (among other elements) via off-gassing. The tools developed here are primarily aimed at capability development but are readily available for use in further modeling of molten salt reactor concepts. As a result, these tools have not yet been validated, and future experimental work to perform this validation is recommended.
In this work we report a framework to understand the role of solvent-salt interactions and how they mediate the performance of sodium-air/O 2 batteries. The utilization of suitable electrolyte materials remains a point of major concern within the research community, as their stability and decomposition pathways during cycling are intimately connected with capacity and cycle life. Glyme based solvents have been widely utilized in Na–O 2 batteries, however, to date no clear correlation between solvent/electrolyte properties and battery performance has been given. Herein, we have examined the effect of glyme chain length (ethylene glycol dimethyl ether DME; diethylene glycol dimethyl ether, DEGDME; and tetraethylene glycol dimethyl ether, TEGME) on the cycling behaviour of Na–O 2 batteries and conclude that overall cell performance is highly dependent on solvent selection, salt concentration and rate of discharge/charge. We demonstrate how solvent selection helps define cell chemistry and performance by linking salt-solvent interactions to enthalpy of dissolution - and subsequently to sodium battery electrolyte properties - through the combination of both experimental and theoretical methodologies. The approaches detailed in this study could be used to predictively prepare electrolytes for Li-air batteries, other glyme-based electrochemical systems and low temperature applications.
Molten salts have attracted considerable interest as essential media for advanced high-temperature technologies, including molten salt reactors, thermal energy storage, high-temperature electrolysis, and pyrochemical processing. Their ability to remain stable in liquid form at elevated temperatures, combined with favorable thermophysical properties and wide electrochemical windows, makes them highly suitable for applications involving heat transfer, energy storage, and hightemperature electrochemical processing. However, despite these advantages, molten salts present challenges due to their chemically reactive nature at high-temperatures, especially in the presence of oxidizing impurities. Salt chemistry can fluctuate through interactions with impurities over time, or fuel burnup in the case of molten salt reactors, often leading to the dissolution of metal species. This dynamic environment not only results in complex redox behavior but also promotes corrosion, which is rarely uniform and frequently manifests as localized degradation driven by structural materials’ compositional differences, electrochemical imbalances, and microstructural susceptibilities.
cis , cis -Muconic acid for downstream separation and catalytic upgrading to adipic acid for nylon-6,6 polymerization.
Core samples originating from Vault 4, Cell E of the Saltstone Disposal Facility (SDF) were collected in September of 2008 (Hansen and Crawford 2009, Smith 2008) and sent to SRNL to measure chemical and physical properties of the material including visual uniformity, mineralogy, microstructure, density, porosity, distribution coefficients (K{sub d}), and chemical composition. Some data from these experiments have been reported (Cozzi and Duncan 2010). In this study, leaching experiments were conducted with a single core sample under conditions that are representative of saltstone performance. In separate experiments, reducing and oxidizing environments were targeted to obtain solubility and Kd values from the measurable species identified in the solid and aqueous leachate. This study was designed to provide insight into how readily species immobilized in saltstone will leach from the saltstone under oxidizing conditions simulating the edge of a saltstone monolith and under reducing conditions, targeting conditions within the saltstone monolith. Core samples were taken from saltstone poured in December of 2007 giving a cure time of nine months in the cell and a total of thirty months before leaching experiments began in June 2010. The saltstone from Vault 4, Cell E is comprised of blast furnace slag, class F fly ash, portland cement, and Deliquification, Dissolution, and Adjustment (DDA) Batch 2 salt solution. The salt solution was previously analyzed from a sample of Tank 50 salt solution and characterized in the 4QCY07 Waste Acceptance Criteria (WAC) report (Zeigler and Bibler 2009). Subsequent to Tank 50 analysis, additional solution was added to the tank solution from the Effluent Treatment Project as well as from inleakage from Tank 50 pump bearings (Cozzi and Duncan 2010). Core samples were taken from three locations and at three depths at each location using a two-inch diameter concrete coring bit (1-1, 1-2, 1-3; 2-1, 2-2, 2-3; 3-1, 3-2, 3-3) (Hansen and Crawford 2009). Leaching experiments were conducted with a section of core sample 3-2. All cores from location 3 were drilled without using water. Core sample 3-2 was drilled from approximately six inches to a depth of approximately 13 inches. Approximately six inches of the core was removed but it broke into two pieces during removal from the bit. At the time of drilling, core material appeared olive green in color (Smith 2008). The fact that the samples were cored as olive green and were received after storage with a gray outer layer is indicative that some oxidation had occurred prior to leaching studies.
A computational non-destructive safeguards study has been conducted using the MCNP6 1 radiation-transport code to examine delayed-neutron (DN) current and delayed-gamma (DG) activity ratio (AR) signatures for a conceptual electrorefining and pyroprocessing (EP) model. Spent-fuel (SNF) inventories were prepared using MCNP6 burnup calculations for a generic Westinghouse fuel assembly 2 with 3% and 5% 235 U enrichments; 20-, 30-, 40-, and 50-GWd/MTU burnups; and 3-, 5-, 10-, 20-, and 30-year cooling times to facilitate parametric evaluations. The electrorefining model was patterned after the INL Mark-IV electrorefiner (ER), 3 and treats the distribution of active metals, noble metals, lanthanides, uranium, and TRUs following fuel dissolution and transport to the molten salt eutectic, liquid cadmium cathode (LCC), and cathode mandrel. Signatures have been assessed before and after electrorefining. DG ARs for 134 Cs/ 137 Cs, 134 Cs/ 154 Eu, and 154 Eu/ 137 Cs were developed, and preliminary assessment of new DG ARs that may be better suited for pyroprocessing safeguards was done. Figure 1 shows calculated DN and DG fluxes for 3% enrichment, 20 GWd/MTU burnup, 3 year cooling before electrorefining, with SNF in the ER, and after electrorefining, with material assignment to processing units. Our work suggests that DN and DG markers can be useful for EP forensic analysis.
A series of model polyelectrolyte complex micelles (PCMs) was prepared to investigate the consequences of neutral and zwitterionic chemistries and distinct charged cores on the size and stability of nanocarriers. Using aqueous reversible addition-fragmentation chain transfer (RAFT) polymerization, we synthesized a well-defined diblock polyelectrolyte system, poly(2-methacryloyloxyethyl phosphorylcholine methacrylate)-block-poly((vinylbenzyl) trimethylammonium) (PMPC-PVBTMA), at various neutral and charged block lengths to compare directly against PCM structure–property relationships centered on poly(ethylene glycol)-block-poly((vinylbenzyl) trimethylammonium) (PEG-PVBTMA) and poly(ethylene glycol)-block-poly(l-lysine) (PEG-PLK). After complexation with a common polyanion, poly(sodium acrylate), the resulting PCMs were characterized by dynamic light scattering (DLS) and small angle X-ray scattering (SAXS). We observed uniform assemblies of spherical micelles with a diameter ~1.5–2× larger when PMPC-PVBTMA was used compared to PEG-PLK and PEG-PVBTMA via SAXS and DLS. In addition, PEG-PLK PCMs proved most resistant to dissolution by both monovalent and divalent salt, followed by PEG-PVBTMA then PMPC-PVBTMA. All micelle systems were serum stable in 100% fetal bovine serum over the course of 8 h by time-resolved DLS, demonstrating minimal interactions with serum proteins and potential as in vivo drug delivery vehicles. This thorough study of the synthesis, assembly, and characterization of zwitterionic polymers in PCMs advances the design space for charge-driven micelle assemblies.
Porous materials with high specific surface area, high porosity, and high electrical conductivity are promising materials for functional applications, including catalysis, sensing, and energy storage. Molten salt dealloying was recently demonstrated in microwires as an alternative method to fabricate porous structures. The method takes advantage of the selective dissolution process introduced by impurities often observed in molten salt corrosion. This work further investigates molten salt dealloying in bulk Ni–20Cr alloy in both KCl–MgCl 2 and KCl–NaCl salts at 700 °C, using scanning electron microscopy, energy dispersive spectroscopy, and X-ray diffraction (XRD), as well as synchrotron X-ray nano-tomography. Micro-sized pores with irregular shapes and sizes ranging from sub-micron to several microns and ligaments formed during the process, while the molten salt dealloying was found to progress several microns into the bulk materials within 1–16 h, a relatively short reaction time, enhancing the practicality of using the method for synthesis. The ligament size increased from ~ 0.7 μm to ~ 1.3 μm in KCl–MgCl 2 from 1 to 16 h due to coarsening, while remaining ~ 0.4 μm in KCl–NaCl during 16 h of exposure. The XRD analysis shows that the corrosion occurred primarily near the surface of the bulk sample, and Cr 2 O 3 was identified as a corrosion product when the reaction was conducted in an air environment (controlled amount sealed in capillaries); thus surface oxides are likely to slow the morphological coarsening rate by hindering the surface diffusion in the dealloyed structure. 3D-connected pores and grain boundary corrosion were visualized by synchrotron X-ray nano-tomography. This study provides insights into the morphological and chemical evolution of molten salt dealloying in bulk materials, with a connection to molten salt corrosion concerns in the design of next-generation nuclear and solar energy power plants.
We study the dissolution mechanism of HSQ (hydrogen silsesquioxane) in base solutions with the addition of chloride salts to elucidate the development mechanism. Reaction mechanisms are proposed based on the dissolution mechanism of quartz. Development kinetics points to two dose-dependent development mechanisms. Considering ion sizes, both hydrated and non-hydrated, and ion exchange, we propose that a combination of a surface dominated reaction at higher doses and a matrix dominated reaction at lower doses accounts for the high development contrast with a NaOH base/NaCl salt mixture. The interplay between the hydrated and non-hydrated ion size leads to higher contrast developers, such as tetramethyl ammonium hydroxide (TMAH) with NaCl.
Corrosion tests are in progress to assess the dissolution behavior of developmental iron phosphate waste forms for salt waste from electrochemical separation operations. Specimens cut from materials made at PNNL to represent a range of waste salt loadings in prototype composition DPF-5 and a range of iron oxide loadings in prototype composition DPF-3 were subjected to modified ASTM C1308 tests to assess the compositional effects on the relative durabilities and retention of immobilized salt cations. The materials were composed of different amounts of glass and crystalline phases. The test results show both the intrinsic durability of the material and the salt cation retention decrease as the total amount of salt cations added to the material is increased. The results of ASTM C1220 and ASTM C1285 tests conducted with materials DPF5-280 and DPF5-336, which contained about 28% and 34% salt cations (on a mass oxide basis) and bounded the durabilities of the other materials, show that solution feedback does not attenuate the dissolution rate. This suggests the degradation of iron phosphate waste forms can be modelled by using a constant rate that probably depends on the composition and volume fraction of the glass phase. A reference composition should be formulated and used in tests to determine those dependencies. The ASTM C1220 and ASTM C1285 tests with DPF5-280 and DPF5-336 remain in progress to corrode the specimens enough to distinguish the relative extents of glass and crystalline phase corrosion by microscopic examinations. Those results are expected to provide insights regarding the relative dissolution rates of crystalline and glass phases and impact on durability to inform the formulation of the reference composition.
The purpose of this report is to provide a review of thermophysical properties and thermochemical characteristics of candidate molten salt coolants, which may be used as a primary coolant within a nuclear reactor or heat transport medium from the Very High Temperature Reactor (VHTR) to a processing plant; for example, a hydrogen-production plant. Thermodynamic properties of four types of molten salts, including LiF-BeF 2 (67 and 33 mol%, respectively; also known as FLiBe), LiF-NaF-KF (46.5, 11.5, and 52 mol%, also known as FLiNaK), and KCl-MgCl 2 (67 and 33 mol%), and sodium nitrate-sodium nitrite-potassium nitrate (NaNO 3 –NaNO 2 –KNO 3 , 7-49-44 mol%, also known as Hitec® salt) have been investigated. Limitations of existing correlations to predict density, viscosity, specific heat capacity, surface tension, and thermal conductivity were identified. The impact of thermodynamic properties on the heat transfer, especially the Nusselt number, was also discussed. Stability of the molten salts with structural alloys and their compatibility with the structural alloys was studied. Nickel and high temperature alloys with dense Ni coatings are effectively inert to corrosion in fluorides, but not so in chlorides. Of the chromium containing alloys, Hastelloy N appears to have the best corrosion resistance in fluorides, while Haynes 230 was the most resistant in chloride. In general, alloys with increasing carbon and chromium content are increasingly subject to corrosion by the fluoride salts FLiBe and FLiNaK due to attack and dissolution of the intergranular chromium carbide. Future research to obtain needed information was identified.
TiO 2 is manufactured for white pigments, solar cells, self-cleaning surfaces and devices, and other photocatalytic applications. The industrial synthesis of TiO 2 entails: (1) the dissolution of ilmenite ore (FeTiO 3 ) in aqueous sulfuric acid which precipitates the Fe while retaining the Ti in solution, followed by (2) dilution or heating the Ti sulfate solution to precipitate the pure form of TiO 2 . The underlying chemistry of these processing steps remains poorly understood. Here we show that the dissolution of a simple Ti IV -sulfate salt, representative of the industrial sulfate process for the production of TiO 2 , immediately self-assembles into a soluble Ti-octadecameric cluster, denoted as {Ti 18 }. We observed {Ti 18 } in solution by small-angle X-ray scattering and Ti extended X-ray absorption fine structure (Ti-EXAFS) analysis, and ultimately crystallized it for absolute identification. The {Ti 18 } metal-oxo cluster was previously reported as a polycation; but shown here, it can also be a polyanion, dependent on the number of sulfate ligands it carries. After immediate self-assembly, the {Ti 18 }-cluster persists until TiO 2 precipitates, with no easily identified structural intermediates in the solution or solid state, despite the fact that the atomic arrangement of {Ti 18 } differs vastly from that of titania. The evolution from solution phase {Ti 18 } to precipitated TiO 2 nanoparticles was detailed by X-ray scattering and Ti-EXAFS. Here, we offer a hypothesis for the key mechanism of complete separation of Fe from Ti in the industrial sulfate process. These findings also highlight the emerging importance of the unusual Ti(Ti) 5 pentagonal building unit, featured in {Ti 18 } as well as other early d 0 transition metal-oxo clusters including Nb, Mo and W. Finally, this study presents an example of crystal growth mechanisms in which the observed “pre-nucleation cluster” does not necessarily predicate the structure of the precipitated solid.
This report is a summary of the international collaboration and laboratory work funded by the US Department of Energy Office of Nuclear Energy Spent Fuel and Waste Science & Technology (SFWST) as part of the Sandia National Laboratories Salt R&D work package. This report satisfies milestone levelfour milestone M4SF-17SN010303014. Several stand-alone sections make up this summary report, each completed by the participants. The first two sections discuss international collaborations on geomechanical benchmarking exercises (WEIMOS) and bedded salt investigations (KOSINA), while the last three sections discuss laboratory work conducted on brucite solubility in brine, dissolution of borosilicate glass into brine, and partitioning of fission products into salt phases.