Search NASA⌕ Search

SEARCH · Search NASA

Results for “Sand heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

The Importance of Meteorological Measurement for the Scientific Study of the Mesosphere

The rocket-borne falling sphere technique has been providing temperature and wind measurements to 90 km. For example, the High Resolution Doppler Imager (HRDI) experiment on the Upper Atmosphere Research Satellite (UARS) and during the GUARA Campaign. The measurement of temperature and wind using the falling sphere method is well known, but will be briefly reviewed. The vertical resolution of the data is examined at different geographical locations and seasons. Time/height sections characterizing the temperature and wind structure will be presented for low (Alcantara, Brazil), middle (Wallops Island and Barking Sands, Hawaii), and high latitudes (ARR and ESRANGE). We address radar quality required, data smoothing, and expected measurement accuracy. Special emphasis will be given to the data gathered during the GUARA campaign, especially small- and large-scale motions including transports of momentum and heat. In the GUARA campaign, the combined Use of small meteorological payloads to measure large scale temperature and wind variations coupled with measurements of small scale turbulence from the larger rockets provided clear cut evidence of gravity wave breaking in the 85 to 90 km region.

Schmidlin, F. J.↗

The Importance of Meteorological Measurements for the Scientific Study of the Mesosphere

The rocket-borne falling sphere technique has been providing temperature and wind measurements to 90 km. For example, the HRDI experiment on the Upper Atmosphere Research Satellite (UARS) and during the GUARA Campaign. The measurement of temperature and wind using the falling sphere method is well known, but will be briefly reviewed. The vertical resolution of the data is examined at different geographical locations and seasons. Time/height sections characterizing the temperature and wind structure will be presented for low (Alcantara, Brazil), middle (Wallops Island and Barking Sands, Hawaii), and high latitudes (ARR and ESRANGE). We address radar quality required, data smoothing, and expected measurement accuracy. Special emphasis will be given to the data gathered during the GUARA campaign, especially small- and large-scale motions including transports of momentum and heat. In the GUARA campaign, the combined use of small meteorological payloads to measure large scale temperature and wind variations coupled with measurements of small scale turbulence from the larger rockets provided clear cut evidence of gravity wave breaking in the 85 to 90 km region.

Schmidlin, F. J.↗

Assessment of Models of Chemically Reacting Granular Flows

A report presents an assessment of a general mathematical model of dense, chemically reacting granular flows like those in fluidized beds used to pyrolize biomass. The model incorporates submodels that have been described in several NASA Tech Briefs articles, including "Generalized Mathematical Model of Pyrolysis of Biomass" (NPO-20068) NASA Tech Briefs, Vol. 22, No. 2 (February 1998), page 60; "Model of Pyrolysis of Biomass in a Fluidized-Bed Reactor" (NPO-20708), NASA Tech Briefs, Vol. 25, No. 6 (June 2001), page 59; and "Model of Fluidized Bed Containing Reacting Solids and Gases" (NPO- 30163), which appears elsewhere in this issue. The model was used to perform computational simulations in a test case of pyrolysis in a reactor containing sand and biomass (i.e., plant material) particles through which passes a flow of hot nitrogen. The boundary conditions and other parameters were selected for the test case to enable assessment of the validity of some assumptions incorporated into submodels of granular stresses, granular thermal conductivity, and heating of particles. The results of the simulation are interpreted as partly affirming the assumptions in some respects and indicating the need for refinements of the assumptions and the affected submodels in other respects.

Bellan, Josette↗

Field Validation of Electrochemical Water Filtration System on an Open Loop Cooling Tower at Nissan Manufacturing Plant in Canton, Mississippi

The U.S. Department of Energy Industrial Efficiency and Decarbonization Office’s Industrial Technology Validation (ITV) program aims to identify and demonstrate the performance of new, emerging, and underutilized technologies in the industrial sector to help inform decisions towards accelerating commercialization and deployment. This ITV demonstration investigated the performance of an early-commercial electrochemical water treatment technology on a cooling tower at an automotive plant. Cooling towers are vital equipment for dissipating heat from industrial processes, but they face challenges related to scaling, corrosion, and the growth of biological contaminants. Effective cooling tower water treatment is therefore essential in reducing these contaminants and other total suspended solids (TSS) and total dissolved solids (TDS). Various treatment systems, such as sand-based filters, centrifugal separators, and disc filters are available, each having its advantages and drawbacks. ElectroCell Systems, a filtration technology provider, offers an electrochemistry-based water treatment system that is skid-mounted and can be configured as a side-stream filtration system.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

NASA's Advanced Environmental Barrier Coatings Development for SiC/SiC Ceramic Matrix Composites: Understanding Calcium Magnesium Alumino-Silicate (CMAS) Degradations and Resistance

Environmental barrier coatings (EBCs) and SiCSiC ceramic matrix composites (CMCs) systems will play a crucial role in next generation turbine engines for hot-section component applications because of their ability to significantly increase engine operating temperatures with improved efficiency, reduce engine weight and cooling requirements. The development of prime-reliant environmental barrier coatings is essential to the viability and reliability of the envisioned CMC engine component applications, ensuring integrated EBC-CMC system durability and designs are achievable for successful applications of the game-changing component technologies and lifing methodologies.This paper will emphasize recent NASA environmental barrier coating developments for SiCSiC turbine airfoil components, utilizing advanced coating compositions, state-of-the-art processing methods, and combined mechanical and environment testing and durability evaluations. The coating-CMC degradations in the engine fatigue-creep and operating environments are particularly complex; one of the important coating development aspects is to better understand engine environmental interactions and coating life debits, and we have particularly addressed the effect of Calcium-Magnesium-Alumino-Silicate (CMAS) from road sand or volcano-ash deposits on the durability of the environmental barrier coating systems, and how the temperature capability, stability and cyclic life of the candidate rare earth oxide and silicate coating systems will be impacted in the presence of the CMAS at high temperatures and under simulated heat flux conditions. Advanced environmental barrier coating systems, including HfO2-Si with rare earth dopant based bond coat systems, will be discussed for the performance improvements to achieve better temperature capability and CMAS resistance for future engine operating conditions.

Environmental barrier coatings↗

Determination of the relative resistance to ignition of selected turbopump materials in high-pressure, high-temperature, oxygen environments, volume 1

Advances in the design of the liquid oxygen, liquid hydrogen engines for the Space Transportation System call for the use of warm, high-pressure oxygen as the driving gas in the liquid oxygen turbopump. The NASA Lewis Research Center requested the NASA White Sands Test Facility (WSTF) to design a test program to determine the relative resistance to ignition of nine selected turbopump materials: Hastelloy X, Inconel 600, Invar 36, Monel K-500, nickel 200, silicon carbide, stainless steel 316, and zirconium copper. The materials were subjected to particle impact and to frictional heating in high-pressure oxygen.

Stoltzfus, Joel M.↗

System and component development for long-duration energy storage using particle thermal energy storage

Energy storage, at various scales, will be required to maintain reliable power supply from variable renewable resources, and improve grid resilience. Long-duration energy storage (10-100 h) can substitute baseload coal power generation and increase levels of renewable power supply. Thermal energy storage (TES) has siting flexibility and the ability to store a large capacity of energy, and thus it has the potential to meet the needs of long-duration energy storage. Here, a novel TES system was developed by using solid particles as storage media and charging/discharging electricity from renewable power connected via the electric grid. The particle TES uses low-cost silica sand at 30-40$/Ton that is stable at high temperatures of >1,000 degrees C. Thus, the particle TES system has an overall low storage cost and high thermal-power efficiency. Key components of the system were conceptually designed and modeled for their performance. Conversion of electricity to thermal energy using electric heating can achieve a >98% charging efficiency, and the conversion of thermal energy back to electricity uses an air-Brayton combined power cycle with >52% thermal-to-electricity efficiency at >1,170 degrees C to achieve a >50% roundtrip efficiency after subtracting estimated plant parasitic losses. Laboratory-scale prototypes were fabricated and tested to verify their design approaches and operations relevant to product-scale components.

25 ENERGY STORAGE↗

Predicting roughness effects in additively manufactured coolant channels with helical enhancements

Additive manufacturing (AM) is a promising technique for fabrication of complex geometries such as those expected to be utilized in the blanket, first wall, and divertor. In the case of cooling, metallic AM may be exploited to embed geometric enhancements (ribs, rifling, etc.) to improve cooling performance. However, due to the roughness of these unfinished internal AM surfaces, prediction of thermal hydraulic performance in such channels is difficult. In this work, we consider a methodology for predicting pressure drop and heat transfer in AM channels containing helical enhancements (e.g. helical ribs, twisted tapes) that allows the incorporation of roughness data through conventional pipe flow correlations. This methodology is tested using experimental friction factor and heat transfer coefficient data from high-pressure helium coolant flow measurements in AM stainless steel tubes fabricated by laser powder bed fusion. Both a featureless AM tube and one containing helical ribs were considered alongside a conventionally manufactured smooth tube. The AM surface roughness is obtained by profilometry and used to predict an equivalent sand-grain roughness, with this equivalent roughness confirmed through AM featureless tube measurements. Under the proposed methodology, this roughness information is incorporated into predictions of friction factor and Nusselt number for the rifled tube. Furthermore, these predictions agree well with experimental data across a large range of Reynolds numbers, encouraging the use of this methodology for thermal hydraulic analysis of similar systems and design of future coolant channel geometries.

Additive manufacturing↗

Design and Performance Optimizations of Advanced Erosion-Resistant Low Conductivity Thermal Barrier Coatings for Rotorcraft Engines

Thermal barrier coatings will be more aggressively designed to protect gas turbine engine hot-section components in order to meet future rotorcraft engine higher fuel efficiency and lower emission goals. For thermal barrier coatings designed for rotorcraft turbine airfoil applications, further improved erosion and impact resistance are crucial for engine performance and durability, because the rotorcraft are often operated in the most severe sand erosive environments. Advanced low thermal conductivity and erosion-resistant thermal barrier coatings are being developed, with the current emphasis being placed on thermal barrier coating toughness improvements using multicomponent alloying and processing optimization approaches. The performance of the advanced thermal barrier coatings has been evaluated in a high temperature erosion burner rig and a laser heat-flux rig to simulate engine erosion and thermal gradient environments. The results have shown that the coating composition and architecture optimizations can effectively improve the erosion and impact resistance of the coating systems, while maintaining low thermal conductivity and cyclic oxidation durability

Zhu, Dongming↗

Direct-Drive Gas-Cooled Reactor Power System: Concept and Preliminary Testing

This paper describes the concept and preliminary component testing of a gas-cooled, UN-fueled, pin-type reactor which uses He/Xe gas that goes directly into a recuperated Brayton system to produce electricity for nuclear electric propulsion. This Direct-Drive Gas-Cooled Reactor (DDG) is designed to be subcritical under water or wet- sand immersion in case of a launch accident. Because the gas-cooled reactor can directly drive the Brayton turbomachinery, it is possible to configure the system such that there are no external surfaces or pressure boundaries that are refractory metal, even though the gas delivered to the turbine is 1144 K. The He/Xe gas mixture is a good heat transport medium when flowing, and a good insulator when stagnant. Judicious use of stagnant cavities as insulating regions allows transport of the 1144-K gas while keeping all external surfaces below 900 K. At this temperature super-alloys (Hastelloy or Inconel) can be used instead of refractory metals. Super-alloys reduce the technology risk because they are easier to fabricate than refractory metals, we have a much more extensive knowledge base on their characteristics, and, because they have a greater resistance to oxidation, system testing is eased. The system is also relatively simple in its design: no additional coolant pumps, heat exchanger, or freeze-thaw systems are required. Key to success of this concept is a good knowledge of the heat transfer between the fuel pins and the gas, as well as the pressure drop through the system. This paper describes preliminary testing to obtain this key information, as well as experience in demonstrating electrically heated testing of simulated reactor components.

Wright, S. A.↗

Thermally Simulated Testing of a Direct-Drive Gas-Cooled Nuclear Reactor

This paper describes the concept and preliminary component testing of a gas-cooled, UN-fueled, pin-type reactor which uses He/Xe gas that goes directly into a recuperated Brayton system to produce electricity for nuclear electric propulsion. This Direct-Drive Gas-Cooled Reactor (DDG) is designed to be subcritical under water or wet-sand immersion in case of a launch accident. Because the gas-cooled reactor can directly drive the Brayton turbomachinery, it is possible to configure the system such that there are no external surfaces or pressure boundaries that are refractory metal, even though the gas delivered to the turbine is 1144 K. The He/Xe gas mixture is a good heat transport medium when flowing, and a good insulator when stagnant. Judicious use of stagnant cavities as insulating regions allows transport of the 1144-K gas while keeping all external surfaces below 900 K. At this temperature super-alloys (Hastelloy or Inconel) can be used instead of refractory metals. Super-alloys reduce the technology risk because they are easier to fabricate than refractory metals, we have a much more extensive knowledge base on their characteristics, and, because they have a greater resistance to oxidation, system testing is eased. The system is also relatively simple in its design: no additional coolant pumps, heat exchanger, or freeze-thaw systems are required. Key to success of this concept is a good knowledge of the heat transfer between the fuel pins and the gas, as well as the pressure drop through the system. This paper describes preliminary testing to obtain this key information, as well as experience in demonstrating electrical thermal simulation of reactor components and concepts.

Godfroy, Thomas↗

Spacecraft Fire Safety Research at NASA Glenn Research Center

Appropriate design of fire detection systems requires knowledge of both the expected fire signature and the background aerosol levels. Terrestrial fire detection systems have been developed based on extensive study of terrestrial fires. Unfortunately there is no corresponding data set for spacecraft fires and consequently the fire detectors in current spacecraft were developed based upon terrestrial designs. In low gravity, buoyant flow is negligible which causes particles to concentrate at the smoke source, increasing their residence time, and increasing the transport time to smoke detectors. Microgravity fires have significantly different structure than those in 1-g which can change the formation history of the smoke particles. Finally the materials used in spacecraft are different from typical terrestrial environments where smoke properties have been evaluated. It is critically important to detect a fire in its early phase before a flame is established, given the fixed volume of air on any spacecraft. Consequently, the primary target for spacecraft fire detection is pyrolysis products rather than soot. Experimental investigations have been performed at three different NASA facilities which characterize smoke aerosols from overheating common spacecraft materials. The earliest effort consists of aerosol measurements in low gravity, called the Smoke Aerosol Measurement Experiment (SAME), and subsequent ground-based testing of SAME smoke in 55-gallon drums with an aerosol reference instrument. Another set of experiments were performed at NASAs Johnson Space Center White Sands Test Facility (WSTF), with additional fuels and an alternate smoke production method. Measurements of these smoke products include mass and number concentration, and a thermal precipitator was designed for this investigation to capture particles for microscopic analysis. The final experiments presented are from NASAs Gases and Aerosols from Smoldering Polymers (GASP) Laboratory, with selected results focusing on realistic fuel preparations and heating profiles with regards to early detection of smoke. SAFFIRE is the upcoming large-scale fire experiment which will be executed in a Cygnus vehicle after it undocks from the ISS.

Aerosol↗

Next Gen High Efficiency Boosted Engine Development

This work represents an advanced engineering research project partially funded by the U.S. Department of Energy (DOE). Ford Motor Company, FEV North America, and Oak Ridge National Laboratory collaborated to develop a next generation boosted spark ignited engine concept. The project goals, specified by the DOE, were 23% improved fuel economy and 15% reduced weight relative to a 2015 or newer light-duty vehicle. The fuel economy goal was achieved by designing an engine incorporating high geometric compression ratio, high dilution tolerance, low pumping work, and low friction. The increased tendency for knock with high compression ratio was addressed using early intake valve closing (EIVC), cooled exhaust gas recirculation (EGR), an active pre-chamber ignition system, and careful management of the fresh charge temperature. Engine weight reduction measures were implemented throughout the engine system making use of composite materials, advanced manufacturing techniques, and architectural choices. This report outlines the analytical, design, fabrication, and test work conducted for the duration of the project. The combustion system stability, EGR tolerance, and knock resistance were validated on a single cylinder engine. An inline six-cylinder engine was then designed targeting application in the Ford F150. Multi-cylinder engines were produced and tested achieving the target vehicle fuel economy improvement of 23% assessed using measured engine fuel consumption combined with a vehicle drive cycle simulation. Actions were identified and designs were demonstrated to achieve the 15% weight reduction target. This project included items covering a range of technology readiness levels. Some of the technologies explored are production ready, while others were investigated to understand the limitations for what can be achieved in a stoichiometric, gasoline-fueled, spark-ignited internal combustion engine.

42 ENGINEERING↗

JSC-Rocknest: a Large-Scale Mojave Mars Simulant (MMS) Based Soil Simulant for In-Situ Resource Utilization Water-Extraction Studies

The Johnson Space Center Rocknest (JSC-RN) simulant was developed in response to a need by NASA's Advanced Exploration Systems (AES) In Situ Resource Utilization (ISRU) project for a simulant to be used in component and system testing for water extraction from Mars regolith. JSC-RN was de-signed to be chemically and mineralogically similar to material from the aeolian sand shadow named Rocknest in Gale Crater, particularly the 1-3 weight percentage water release as measured by the Sample Analysis at Mars (SAM) instrument. Rocknest material is a proxy for average martian soils, which are unconsolidated and could be easily scooped by rovers or landers in order to extract water. One way in which water can be extracted from aeolian material is through heating, where adsorbed and structural water is thermally removed from minerals. The water can then be condensed and used as drinking water or split and used as propellant for spacecraft or as a source of breathable O2. As such, it was essential that JSC-RN contained evolved gas profiles, especially low temperature water (less than 400 degrees Centigrade), that mimicked what is observed in martian soils. Because many of these ISRU tests require hundreds of kilograms of Mars soil simulant, it was essential that JSC-RN be cost-effective and based on com-ponents that could be purchased commercially (i.e., not synthesized in the lab). Here, we describe the JSC-RN martian soil simulant, which is ideal for large-scale production and use in ISRU water extraction studies.

Hogancamp, J. V.↗

Surface and Buried Thermal, and RGB Unexploded Ordnance Data Collection

This document provides a description of a data collection campaign of unexploded ordnance (UXOI) set. The dataset captures a controlled UAV imaging campaign designed to support detection of UXO across varied environmental conditions. Data were collected during three campaigns in Norris and Northeast Knoxville, Tennessee, using RGB, and thermal sensors mounted on Parrot UKR. In total, the dataset contains 9925 images, 26 full-motion video, and approximately 81.99 GB of data, collected across late spring/summer conditions, every hour during sunlight, and multiple surface contexts, including tall grass, short grass, gravel, as well as buried in sand, and other gravel mixtures. The collection was designed to capture thermal and visual variability relevant to UXO detection in agricultural land, bare earth, and subsurface. Review of the imagery showed that ordnance was most detectable during periods of changing solar input, especially approximately 10-60 minutes after sunrise, approximately 20-60 minutes after sunset, and 2-3 min after cloud cover interrupted prolonged solar heating. These conditions increased thermal contrast because many ordnance items retained or released heat differently than the surrounding vegetation and ground surface. This dataset provides a useful resource for developing and evaluating airborne UXO detection methods under realistic field conditions. All ordnance used in the study was inert, and thermal behavior may differ from that of live ordnance. In addition, variation in ordnance type, composition, and placement introduced differences in thermal response that should be considered when interpreting results.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Cabin fuselage structural design with engine installation and control system

Design requirements for the cabin, cabin system, flight controls, engine installation, and wing-fuselage interface that provide adequate interior volume for occupant seating, cabin ingress and egress, and safety are presented. The fuselage structure must be sufficient to meet the loadings specified in the appropriate sections of Federal Aviation Regulation Part 23. The critical structure must provide a safe life of 10(exp 6) load cycles and 10,000 operational mission cycles. The cabin seating and controls must provide adjustment to account for various pilot physiques and to aid in maintenance and operation of the aircraft. Seats and doors shall not bind or lockup under normal operation. Cabin systems such as heating and ventilation, electrical, lighting, intercom, and avionics must be included in the design. The control system will consist of ailerons, elevator, and rudders. The system must provide required deflections with a combination of push rods, bell cranks, pulleys, and linkages. The system will be free from slack and provide smooth operation without binding. Environmental considerations include variations in temperature and atmospheric pressure, protection against sand, dust, rain, humidity, ice, snow, salt/fog atmosphere, wind and gusts, and shock and vibration. The following design goals were set to meet the requirements of the statement of work: safety, performance, manufacturing and cost. To prevent the engine from penetrating the passenger area in the event of a crash was the primary safety concern. Weight and the fuselage aerodynamics were the primary performance concerns. Commonality and ease of manufacturing were major considerations to reduce cost.

Balakrishnan, Tanapaal↗

Hypervelocity Impact (HVI): Tile Small Targets A-1, Ag-1, B-1, and Bg-1 - Volume 8

During 2003 and 2004, the Johnson Space Center's White Sands Testing Facility in Las Cruces, New Mexico conducted hypervelocity impact tests on the space shuttle wing leading edge. Hypervelocity impact tests were conducted to determine if Micro-Meteoroid/Orbital Debris impacts could be reliably detected and located using simple passive ultrasonic methods. The objective of Targets A-1, Ag-1, B-1, and Bg-1 was to study hypervelocity impacts on the reinforced Shuttle Heat Shield Tiles of the Wing. Impact damage was detected using lightweight, low power instrumentation capable of being used in flight.

Gorman, Michael R.↗

Martian B Storm Genesis and Evolution: Initial Analysis of Thermal Datasets.

Introduction: Dust lifting on Mars likely occurs primarily as a result of the exchange of momentum between the atmosphere and the surface via saltation. During saltation, sand-sized particles are mobilized but do not enter into suspension. When these larger particles fall back to the surface, kinetic energy is transferred to smaller dust particles which are then lofted into suspension in the atmosphere. Depending on the altitude to which dust is lofted, it can have a significant effect on atmospheric temperatures. As a strong absorber and emitter in the infrared, dust can influence atmospheric heating and modify the global circulation and weather on Mars [1,2]. Although dust is present in Mars’ atmosphere throughout the year, the atmosphere is generally dustier during the second half of the year when Mars is near perihelion. Observations reveal that episodic global-scale dust storms and fairly regular regional-scale dust storms are superimposed on a well-defined and highly repeatable seasonal cycle of dust opacity and associated mid-level atmospheric temperature responses. Kass et al. (2016) used 50 Pa temperature observations from MRO/MCS to identify three highly repeatable time periods during which regional dust storms occur, and designated them the “A”, “B” and “C” storms. While “A” and “C” storms have been studied a fair amount to-date, “B” storms have not yet been investigated in detail. This study explores the generation and evolution of the annually recurring regional dust storm known as the “B” storm, which was identified and categorized by Kass et al. (2016) based on 25 km (50 Pa) temperature observations. The B storm is a southern-hemisphere (SH) phenomenon that originates at the cap edge just after perihelion and which reaches peak intensity during the SH summer solstice, Ls 270. It may originate from the cap edge storms that spawn near the edge of the seasonal CO2 cap during retreat, but the mechanisms for B storm genesis have yet to be determined definitively [1]. Methods: We will use observational data sets and a global climate model (GCM) to investigate “B” regional storms. The data analysis component will include the analysis of imagery from MGS/MOC and MRO/MARCI, and spectroscopic data sets of dust and temperatures from MGS/TES and MRO/MCS with the goal of fully characterizing the behavior of these storms. Both MGS and TES provide data well-suited for temperature analysis at 25 km. MCS measures atmospheric temperature, dust extinction, and water ice extinction at 5 km intervals from the surface to about 80 km. TES measured atmospheric temperatures, column dust and water ice opacities, and column water vapor abundances. Measurements made by TES extended from the surface to about 40 km [1]. At the 50 Pa (25 km) level, local dust events usually confined to shallower depths are effectively filtered out of the analysis leaving the regional dust events identifiable by their temperature signatures [1]. Our preliminary analysis makes use of the fact that the brightness temperature at 15 microns (T15 temperature) is a close approximation to observed temperature at 25 km. We first reproduce the zonal mean 50 Pa level temperature plots for MY 29-32 to establish a baseline for our procedures moving forward [1]. Expanding on Kass et al. (2016), we include recent MCS data from MY 33 and 34 as well. Preliminary Analysis: The daytime (3PM) T15 temperatures in Figure 1 indicate: in MY 29, a strong A storm at Ls 240, a B storm at high southern latitudes just after Ls 270, and a C storm at Ls 320; in MY 30, a B storm at Ls 270; in MY 31 & MY 32, a B storm just before Ls 270; in MY 33, a B storm at Ls 270; and in MY 34, a strong A storm in the northern hemisphere at Ls 210, and a B storm around Ls 270 although there is a data gap. For the B storms, each is indicative of lofted dust and resultant warming. The daytime temperature structure illustrates that the B storm occurs annually around Ls 270 and is confined to high southern latitudes. It reaches its peak intensity around SH summer solstice, Ls 270, consistently for all six MY assessed. Since direct solar heating is absent overnight, the nighttime T15 temperatures (Figure 2) are often useful for differentiating the heat signature of direct solar heating from the dynamical response to that heating. However, in the southern polar latitudes at perihelion the sun does not set and direct solar heating remains present throughout the night. Importantly for our study, dust lofted in the B storm experiences this direct heating day and night for the entirety of its lifetime. The B storm expands as far north as -60 latitude and decays in latitudinal extent more gradually than it grows. This feature is less obvious in the nighttime (3AM) T15 temperatures (Figure 2). The temperature signal is stronger at night for MY 30-33. The warm pool is larger in area relative to the background at night in these four cases. This more uniform warming masks the “tail” feature somewhat, such that it is barely noticeable during these years. Unfortunately, gaps in MCS data in MY 29 and 34 prevent confirmation of the tail feature during those years, however, the B storm temperature signature follows a very different pattern than that described for MY 30-33. MY 29 and 34 appear to show smaller centers of warming at night and larger centers of warming during the day. This is in opposition to that previously described for MY 30-33. Conclusions and Future Work: We will continue investigating the heat signatures of B storms by looking at the total column heating as recorded by TES. We will also look at lower altitudes for patterns that may describe the relationship between B storms and the cap edge storms that develop while the seasonal cap is retreating. In the future, we will use GCM simulations to determine the atmospheric and thermo-dynamic conditions associated with these storms.

Courtney Marylou Batterson↗