Search NASA⌕ Search

SEARCH · Search NASA

Results for “Scrape-off-layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Numerical Modeling of Edge-Localized-Mode Filaments on Divertor Plates Based on Thermoelectric Currents

Edge localized modes (ELMs) are qualitatively and quantitatively modeled in tokamaks using current bursts which have been observed in the scrape-off-layer (SOL) during an ELM crash. During the initial phase of an ELM, a heat pulse causes thermoelectric currents. They first flow in short connection length flux tubes which are initially established by error fields or other nonaxisymmetric magnetic perturbations. The currents change the magnetic field topology in such a way that larger areas of short connection length flux tubes emerge. Then currents predominantly flow in short SOL-like flux tubes and scale with the area of the flux tube assuming a constant current density. Quantitative predictions of flux tube patterns for a given current are in excellent agreement with measurements of the heat load and current flow at the DIII-D target plates during an ELM cycle.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observation of Efficient Lower Hybrid Current Drive at High Density in Diverted Plasmas on the Alcator C-Mod Tokamak

Here, efficient lower hybrid current drive (LHCD) is demonstrated at densities up to $\bar{n}_e$ ≈ 1.5 x 10 20 m –3 in diverted plasmas on the Alcator C-Mod tokamak by operating at increased plasma current - and therefore reduced Greenwald density fraction. This density exceeds the nominal “LH density limit” at $\bar{n}_e$ ≈ 1.0 x 10 20 m –3 reported previously, above which an anomalous loss of current drive efficiency was observed. The recovery of current drive efficiency to a level consistent with engineering scalings is correlated with a reduction in density shoulders and turbulence levels in the far scrape-off layer. Concurrently, rf wave interaction with the edge and/or scrape-off-layer plasma is reduced, as indicated by a minimal broadening of the wave frequency spectrum measured at the plasma edge. These results have important implications for sustaining steady-state tokamak operation and indicate a pathway forward for implementing efficient LHCD in a reactor.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Structure of the controlled halo-current magnetic field in the T-10 tokamak

In the T-10 tokamak, the magnetic field spatially resonant with a helical MHD perturbation is generated using the controlled halo current supplied using a contact method in the scrape-off-layer plasma. This paper is concerned with studying the spatial structure of the halo current and its magnetic field. For this purpose, the magnetic field of the halo current was measured in one of the cross sections of the torus near the tokamak vacuum vessel wall. The spatial distribution of the magnetic field as a function of the halo current configuration was calculated in the cylindrical approximation. The terms proportional to the plasma pressure were disregarded. The configuration of the halo current and the spatial structure of its magnetic field were determined by comparing the calculated and experimental results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Investigation of the Edge Plasma Parameters and Measurements of the Plasma Longitudinal Rotation Velocity by a Mach Probe in a Lithium Experiment on the T-11M Tokamak

The edge plasma parameters were measured by means of a Mach probe in a lithium experiment on the T-11M tokamak. The angular and radial distributions of the ion saturation current, along with the radial distribution of the electron temperature, were obtained in different modes of tokamak operation. The radial distributions of the electron temperature and ion saturation current in the main operating mode (L-mode) revealed a peak in the scrape-off-layer of the vertical limiter (lithium emitter), which can indicate the formation of a magnetic island in this region. The measured plasma flow velocity along the magnetic field was found to be close to one-half of the ion sound velocity for Li{sup +} ions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Intrinsic Rotation in Axisymmetric Devices

Toroidal rotation is critical for fusion in tokamaks, since it stabilizes instabilities that can otherwise cause disruptions or degrade confinement. Unlike present-day devices, ITER might not have enough neutral-beam torque to easily avoid these instabilities. We must therefore understand how the plasma rotates intrinsically, that is, without applied torque. Experimentally, torque-free plasmas indeed rotate, with profiles that are often non-flat and even non-monotonic. The rotation depends on many plasma parameters including collisionality and plasma current, and exhibits sudden bifurcations (rotation reversals) at critical parameter values.Since toroidal angular momentum is conserved in axisymmetric systems, and since experimentally inferred momentum transport is much too large to be neoclassical, theoretical work has focused on rotation drive by nondiffusive turbulent momentum fluxes. In the edge, intrinsic rotation relaxes to a steady state in which the total momentum outflux from the plasma vanishes. Ion drift orbits, scrape-off-layer flows, separatrix geometry, and turbulence intensity gradient all play a role. In the core, nondiffusive and viscous momentum fluxes balance to set the rotation gradient at each flux surface. Although many mechanisms have been proposed for the nondiffusive fluxes, most are treated in one of two distinct but related gyrokinetic formulations. In a radially local fluxtube, appropriate for rho star <<1, the lowest-order gyrokinetic formulations exhibit a symmetry that prohibits nondiffusive momentum flux for nonrotating plasmas in an up- down symmetric magnetic geometry with no ExB shear. Many symmetry-breaking mechanisms have been identified, but none have yet been conclusively demonstrated to drive a strong enough flux to explain commonly observed experimental rotation profiles. Radially global gyrokinetic simulations naturally include many symmetry-breaking mechanisms, and have shown cases with experimentally relevant levels of nondiffusive flux. These promising early results motivate further work to analyze, verify, and validate.This article provides a pedagogical introduction to intrinsic rotation in axisymmetric devices. Intended for both newcomers to the topic and experienced practitioners, the article reviews a broad range of topics including experimental and theoretical results for both edge and core rotation, while maintaining a focus on the underlying concepts.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Partnership for Edge Physics Simulation

A major goal of our participation in the Edge Physics Simulation project has been to contribute to the understanding of the self-organization of tokamak turbulence fluctuations resulting in the formation of a staircase structure in the ion temperature. A second important goal is to demonstrate how small scale turbulence in plasmas self-organizes with dynamically driven quasi-stationary flow shear. These goals have been accomplished through the analyses of the statistical properties of XGC1 flux driven Gyrokinetic electrostatic ion temperature gradient (ITG) turbulence simulation data in which neutrals are included. The ITG turbulence data, and in particular fluctuation data, were obtained from a massively parallel flux-driven gyrokinetic full-f particle-in-cell simulation of a DIII-D like equilibrium. Below some the findings are summarized. It was observed that the emergence of staircase structure is related to the variations in the normalized temperature gradient length (R/LT) and the poloidal flow shear. Average turbulence intensity is found to be large in the vicinity of minima in R/LTi, where ITG growth is expected to be lower. The distributions of the occurrences of potential fluctuation are found to be Gaussian away from the staircase-step locations, but they are found to be non-Gaussian in the vicinity of staircase-step locations. The results of analytically derived expressions for the distribution of the occurrences of turbulence intensity and intensity flux were compared with the corresponding quantities computed using XGC1 simulation data and good agreement is found. The derived expressions predicts inward and outward propagation of turbulence intensity flux in an intermittent fashion. The outward propagation of turbulence intensity flux occurs at staircase-step locations and is related to the change in poloidal flow velocity shear and to the change in the ion temperature gradient. The standard deviation, skewness and kurtosis for turbulence quantities were computed and found to be large in the vicinity of the staircase-step structures. Large values of skewness and kurtosis can be explained by a temporary opening and closing of the structure which allows turbulence intensity events to propagate. The staircase patterns may reduce the ion heat transport and a manipulation of these patterns may be used to optimize heat transport in tokamaks. An additional objective of the research in support of the Edge Physics Simulation initiative has been to improve the understanding of scrape-off layer thermal transport. In planning experiments and designing future tokamaks, it is important to understand the physical effects that contribute to divertor heat-load fluxes. The research accomplished will contribute to developing new models for the scrape-off layer region. The XGC0 code was used to compute the heat fluxes and the heat-load width in the outer divertor plates of C-Mod and DIII-D tokamaks. It was observed that the width of the XGC0 neoclassical heat-load was approximately inversely proportional to the total plasma current. Anomalous transport in the H-mode pedestal region of five Alcator C-Mod discharges, representing a collisionality scan, was analyzed. The understanding of anomalous transport in the pedestal region is important for the development of a comprehensive model for the H-mode pedestal slope. It was found that the electron thermal anomalous diffusivities at the pedestal top increase with the electron collisionality. This dependence can point to the DRIBM as the modes that drive the anomalous transport in the plasma edge of highly collisional discharges. The effects of plasma shaping on the H-mode pedestal structure was also investigated. The differences in the predicted H-mode pedestal width and height for the DIII-D discharges with different elongation and triangularities were discussed. For the discharges with higher elongation, it was found that the gradients of the plasma profiles in the H-mode pedestal reach semi-steady states. In these simulations, the pedestal slowly continued to evolve to higher pedestal pressures and bootstrap currents until the peeling ballooning stability conditions were satisfied. The discharges with lower elongation do not reach the semi-steady state, and ELM crashes were triggered at earlier times. The plasma elongation was found to have a stronger stabilizing effect than the plasma triangularity. For the discharges with lower elongation and lower triangularity, the ELM frequency was large, and the H-mode pedestal evolves rapidly. It was found that the temperature of neutrals in the scrape-off-layer region can affect the dynamics of the H-mode pedestal buildup. However, the final pedestal profiles were nearly independent of the neutral temperature. The elongation and triangularity affected the pedestal widths of plasma density and electron temperature profiles differently. This study illustrated a new mechanism for controlling the pedestal bootstrap current and the pedestal stability.

97 MATHEMATICS AND COMPUTING↗

Center for Extended Magnetohydrodrynamic Modeling

This work used the NIMROD code to solve two tokamak regimes found on the DIII-D tokamak. The first regime studied is the Quiescent H-mode regime that has the advantage of enabling tokamak high performance without the deleterious effects of Edge Localized Modes (ELMs). ELMs are a possible impediment to the success of tokamaks as a burning plasma reactor and the QH mode regime provides a mechanism for avoiding it. The QH mode achieves this state due to the appearance of long wavelength instability that saturates instead of reaching an ELM state. NIMROD simulations were able to describe many of the features of a particular discharge, including the importance of shear flow in reaching the state, the role of the parallel heat flux to decorrelate the temperature and velocity fluctations, and in the correlation of density and velocity fluctations to provide the density pumpout. This work resulted in two direct publications and an invited talk. Progress towards these publications resulted in two more publications (verification and solving the Grad-Shafranov equation with scrape-off-layer currents). The second regime studied was the Giant Sawtooth regime whereby energetic particles affect the stability of the 1/1 mode. This work resulted in performance improvements of NIMROD's energetic particle algorithms, and improvements to the drift-kinetic equation infrastructure used by both continuum and energetic particle closure methods. The studies proved more computationally demanding than expected because as the 1/1 is stabilized, the near marginal conditions cause long simulations times. Publication of this work is in progress under other funding.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Boundary, SOL, and Divertor Physics Studies on TCV (Final Report for Research Funded by DoE Award DE-SC0020327)

Research supported under this grant was organized around two diagnostic systems installed on the TCV tokamak located at EPFL in Lausanne, Switzerland: Multi-Spectral Imaging (MSI) and Gas-Puff Imaging (GPI). MSI monitors 2-d time-history images of up to 10 spectral lines, in the visible, using identical views for all wavelengths. The primary application of MSI is to infer 2-d time histories of electron temperature and density in the Scrape-Off-Layer (SOL) of diverted plasmas, utilizing ratios of emission from multiple neutral helium lines. The atomic models are validated against 1-d Thomson scattering measurements. SOL density and temperature maps are analyzed to infer divertor dynamics, including particle and power flows, for a variety of divertor configurations, and specifically as flux expansion along the long-legged outboard divertor is systematically varied. GPI is used to measure details of edge fluctuations in the SOL, particularly as a function of plasma triangularity (δ), including both positive and negative δ. A threshold is found, whereby for δ<-0.3, edge turbulence in the far SOL is completely suppressed. Dynamics of the filamentary turbulence was also analyzed using advance machine learning techniques. Research in support of four PhD theses was carried out within the scope of this Award, including 2 at MIT and 2 at EPFL.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Global 3D Simulations of the Tokamak Edge Region

The goal of this project is to better understand magnetized plasma dynamics at the edge region of the tokamak, including both closed-flux-surface region and the scrape-off-layer (SOL), through analytical analysis and advanced numerical simulations. Under the auspices of the U.S. DOE, the PI, along with students and collaborators have made a significant progress. These results were disseminated by 13 peer-reviewed article and many presentations and posters in domestic and international conferences.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Plasma Surface Interactions: Predicting the Performance and Impact of Dynamic PFC Surfaces

Interactions of plasma with material surfaces in tokamaks have long been recognized as crucial for development of practical fusion energy production. Such interactions can adversely affect both plasma performance and properties of tokamak materials by means of a large variety of physical phenomena involved. Among such phenomena attracting researchers’ attention are various mechanisms of erosion of plasma-facing components (PFCs) and resulting contamination of plasma with impurities, tritium retention in the first wall material, radiation damage and modification of mechanical properties of the tokamak structural materials, dust production, thermal loading limits and possibility of PFCs melting failure, etc. Aside from these phenomena, one of the main mechanisms strongly affecting fusion plasma discharge conditions is plasma recycling. The recycling taking place on PFCs, most importantly on divertor plates where the plasma fluxes are very large, is a major source of neutrals sustaining plasma pressure in scrape-off-layer (SOL) and contributing to SOL power dissipation by forming so-called detached plasma conditions in the divertor. Recycled neutrals can also play an important role in the edge plasma transport and stability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Center for Integrated Simulation of Fusion Relevant RF Actuators

This project was part of the “Center for Integrated Simulation of Fusion Relevant RF Actuators” SciDAC-4 project, led by Dr. Paul Bonoli (MIT). Rather than use an acronym (CISFRRFA), the project will be referred to in this document as the “RF-SciDAC4”. The larger SciDAC-4 project goals were to: 1. Develop an integrated simulation of the antenna + sheath + scrape-off-layer + core plasma system which fully utilizes leadership class computing resources to move towards a quantitative predictive capability for the response to RF power. 2. Work closely with the SciDAC-4 Whole Device Modeling (WDM) community to make both our new code development efforts, as well as the established hierarchy of RF tools, available within their environment, and to utilize WDM technologies to implement the couplings below. 3. Validate this predictive capability on appropriately diagnosed experiments including dedicated RF test stands, linear devices, and existing tokamaks. 4. Use these tools to inform design of robust, impurity-mitigating RF heating and current drive sources for future fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Biasing, Acquisition and Interpretation of a Dense Langmuir Probe Array in NSTX

A dense array of 99 Langmuir probes has been installed in the lower divertor region of the National Spherical Torus Experiments (NSTX). This array is instrumented with a system of elec- tronics that allows flexibility in the choice of probes to bias as well as the type of measurement (including standard swept, single probe, triple probe and operation as passive floating potential and scrape-off-layer (SOL) current monitors). The use of flush-mounted probes requires careful inter- pretation. The time dependent nature of the SOL makes swept-probe traces difficult to interpret. To overcome these challenges, the single- and triple-Langmuir probe signals are used in comple- mentary fashion to determine the temperature and density at the probe location. A comparison to mid-plane measurements is made. Work is supported by DOE contracts DE-AC02-09CHI1466 and DE-PS02-07ER07-29.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Microscopic Motion of Liquid Metal Plasma Facing Components In A Diverted Plasma

Liquid metal plasma facing components (PFCs) have been identified as an alternative material for fusion plasma experiments. The use of a liquid conductor where significant magnetic fields are present is considered risky, with the possibility of macroscopic fluid motion and possible ejection into the plasma core. Analysis is carried out on thermoelectric magnetohydrodynamic (TEMHD) forces caused by temperature gradients in the liquid-container system itself in addition to scrape-off-layer currents interacting with the PFC from a diverted plasma. Capillary effects at the liquid-container interface will be examined which govern droplet ejection criteria. Stability of the interface is determined using linear stability methods. In addition to application to liquidmetal PFCs, thin film liquidmetal effects have application to current and future devices where off-normal events may liquefy portions of the first wall and other plasma facing components.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

HIS-TORIC: Extending core ICRF wave simulation to include realistic SOL plasmas

This paper presents a novel approach to incorporating an arbitrarily shaped edge scrape-off-layer (SOL) plasma and an ion cyclotron range of frequency (ICRF) antenna structure into existing core ICRF wave simulation models. We partition the entire computation domain into two sub-domains: a core and an edge region. Simulations in each domain are performed separately with appropriate numerical solvers. For the core, the TORIC ICRF solver [M. Brambilla, Plasma Phys. Contrl. Fusion 41, 1 (1999)] was modified to impose an essential (Dirichlet) boundary condition at its interface with the edge domain. In the edge, a finite element method (FEM) is used to solve a cold collisional plasma model. The domains are then joined together using the continuity boundary condition for the tangential electric and magnetic fields at their interfaces (Hybrid Integration of SOL to TORIC: HIS-TORIC). The model developed here was tested using an ICRH H minority heating scenario on the Alcator C-Mod tokamak [I. Hutchinson et. al., Phys. Plasmas 1, 1511 (1994)]. The simulated pattern of core wave propagation agrees well with a standard TORIC simulation. This approach opens the possibility of using a realistic diverted SOL plasma and a complicated 3D RF antenna together with a rigorous hot core plasma model, while requiring only minimal modification to existing RF codes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Lower hybrid wave edge power loss quantification on the Alcator C-Mod tokamak

For the first time, the power deposition of Lower Hybrid RF waves into the edge plasma of a diverted tokamak has been systematically quantified. Edge deposition represents a parasitic loss of power that can greatly impact the use and efficiency of Lower Hybrid Current Drive (LHCD) at reactor-relevant densities. Through the use of a unique set of fast time resolution edge diagnostics, including innovative fast-thermocouples, an extensive set of Langmuir probes, and a Ly? ionization camera, the toroidal, poloidal and radial structure of the power deposition has been simultaneously determined. Power modulation was used to directly isolate the RF effects due to the prompt (t < ?E ) response of the scrape-off-layer (SOL) plasma to LHRF power. LHRF power was found to absorb more strongly in the edge at higher densities. It is found that a majority of this edge-deposited power is promptly conducted to the divertor. This correlates with the loss of current drive efficiency at high density previously observed on Alcator C-Mod, and displaying characteristics that contrast with the local RF edge absorption seen on other tokamaks. Measurements of ionization in the active divertor show dramatic changes due to LHRF power, implying that divertor region can be key for the LHRF edge power deposition physics. These observations support the existence of a loss mechanism near the edge for LHRF at high density (ne > 1.0 1020 [m?3]). Results will be shown addressing the distribution of power within the SOL, including the toroidal symmetry and radial distribution. These characteristics are important for deducing the cause of the reduced LHCD efficiency at high density and motivates the tailoring of wave propagation to minimize SOL interaction, for example, through the use of high-field-side launch.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Impact of lithium wall conditioning and wave-frequency on high density lower hybrid current drive experiment on EAST

A series of dedicated lower hybrid current drive (LHCD) experiments on EAST shows that lithium wall conditioning extends LH current drive and heating up to the line-averaged density of n ̅_e≈ 4x1019 m-3 for both 2.45 and 4.6 GHz. Current drive at such a high density is crucial for the development of long-pulse non-inductive scenarios on EAST. With lithiation, the LH power injection of 1.5 MW at 2.45 GHz resulted in a drop of loop voltage of ~ 0.3 V, which is a comparable loop voltage drop observed with 1.1 MW at 4.6 GHz. The observed decrease in loop voltage is attributed mostly to the RF heating effect. Another LHCD experiment suggests that lithium wall coating has a more significant impact on the scrape-off-layer (SOL) properties than changes in the Greenwald fraction. LHCD at 2.45 GHz still suffers from a loss of efficiency. Enhanced power ionization in front of the launcher may cause the onset of density-dependent wave instabilities. The rise in the midplane SOL density may also accelerate a transition in the divertor regime, leading to additional ionization and collisional losses in the X-point divertor plasma. Ray-tracing modeling supports that a lower wave frequency is more prone to collisional power loss. The experiments confirm that lithiation is a useful tool to control the SOL plasma, and suggest that density control in front of the launcher may be critical to mitigating power loss mechanisms in the plasma boundary.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observation of Efficient Lower Hybrid Current Drive at High Density in Diverted Plasmas on the Alcator C-Mod Tokamak

Efficient lower hybrid current drive (LHCD) is demonstrated at densities up to ne≈1.5×10^20 m^-3 in diverted plasmas on the Alcator C-Mod tokamak by operating at increased plasma current - and therefore reduced Greenwald density fraction. This density exceeds the nominal "LH density limit" at ne≈1.0×10^20 m^-3 reported previously, above which an anomalous loss of current drive efficiency was observed. The recovery of current drive efficiency to a level consistent with engineering scalings is correlated with a reduction in density shoulders and turbulence levels in the far scrape-off layer. Concurrently, rf wave interaction with the edge and/or scrape-off-layer plasma is reduced, as indicated by a minimal broadening of the wave frequency spectrum measured at the plasma edge. These results have important implications for sustaining steady-state tokamak operation and indicate a pathway forward for implementing efficient LHCD in a reactor.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fusion-Enabled Pluto Orbiter and Lander

The Pluto orbiter mission proposed here is credible and exciting. The benefits to this and all outer-planet and interstellar-probe missions are difficult to overstate. The enabling technology, Direct Fusion Drive, is a unique fusion engine concept based on the Princeton Field-Reversed Configuration (PFRC) fusion reactor under development at the Princeton Plasma Physics Laboratory. The truly game-changing levels of thrust and power in a modestly sized package could integrate with our current launch infrastructure while radically expanding the science capability of these missions. During this Phase I effort, we made great strides in modeling the engine efficiency, thrust, and specific impulse and analyzing feasible trajectories. Based on 2D fluid modeling of the fusion reactors outer stratum, its scrape-off-layer (SOL), we estimate achieving 2.5 to 5 N of thrust for each megawatt of fusion power, reaching a specific impulse, Isp, of about 10,000 s. Supporting this model are particle-in-cell calculations of energy transfer from the fusion products to the SOL electrons. Subsequently, this energy is transferred to the ions as they expand through the magnetic nozzle and beyond. Our point solution for the Pluto mission now delivers 1000 kg of payload to Pluto orbit in 3.75 years using 7.5 N constant thrust. This could potentially be achieved with a single 1 MW engine. The departure spiral from Earth orbit and insertion spiral to Pluto orbit require only a small portion of the total delta-V. Departing from low Earth orbit reduces mission cost while increasing available mission mass. The payload includes a lander, which utilizes a standard green propellant engine for the landing sequence. The lander has about 4 square meters of solar panels mounted on a gimbal that allows it to track the orbiter, which beams 30 to 50 kW of power using a 1080 nm laser. Optical communication provides dramatically high data rates back to Earth. Our mass modeling investigations revealed that if current high-temperature superconductors are utilized at liquid nitrogen temperatures, they drive the mass of the engine, partly because of the shielding required to maintain their critical temperature. Second generation materials are thinner but the superconductor is a very thin layer deposited on a substrate with additional layers of metallic classing. Tremendous research is being performed on a variety of these superconducting materials, and new irradiation data is now available. This raises the possibility of operating nearfuture high-temperature superconductors at a moderately low temperature to dramatically reduce the amount of shielding required. At the same time, a first generation space engine may require low-temperature superconductors, which are higher TRL and have been designed for space coils before (AMS-02 experiment for the ISS). We performed detailed analysis of the startup system and thermal conversion system components. The ideal working fluid was determined to be a blend of Helium and Xenon. No significant problems were identified with these subsystems. For the RF system, we conceived of a new, more efficient design using state-of-the-art switch amplifiers, which have the potential for 100% efficiency. This report presents details of our engine and trajectory analyses, mass modeling efforts, and updated vehicle designs.

temperature↗