Search NASA⌕ Search

SEARCH · Search NASA

Results for “Slender Structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Effect of orbital transfer loads on large platforms

A preliminary automated structural sizing procedure suitable for conceptual design and early tradeoff studies of large truss platforms configured for shuttle transportation to LEO is discussed as well as some orbital transfer design considerations. Platforms that are sized to withstand orbital transfer loads for the LEO to GEO maneuver are compared to platforms sized only for LEO application. It is concluded that for platforms supporting low mass distributed payloads, platform and strut frequency requirements are strong design drivers for LEO applications. The struts are found to be extremely slender, thinswalled, and of small diameter. If full advantage is to be taken of these minimum mass designs, a manufacturing capability must be developed for long straight struts. For platforms that are to be transferred from LEO to GEO in a deployed state, the orbital transfer loads become design drivers. However, even for an initial thrust-to-weight ratio equal to 0.1, a platform on the order of 100 m diameter appears packageable with its OTV in one shuttle flight, and larger platforms appear possible at lower thrust-to-weight ratios.

Walz, J. E.↗
NASA NTRS1984

Radar response from vegetation with nodal structure

Radar images from the SEASAT synthetic aperture radar (SAR) produced unusually high returns from corn and sorghum fields, which seem to indicate a correlation between nodal separation in the stalk and the wavelength of the radar. These images also show no difference in return from standing or harvested corn. Further investigation using images from the Shuttle Imaging Radar (SIR-A) substantiated these observations and showed a degradation of the high return with time after harvest. From portions of corn and sweet sorghum stalks that were sampled to measure stalk water content, it was determined that near and after maturity the water becomes more concentrated in the stalk nodes. The stalk then becomes a linear sequence of alternating dielectrics as opposed to a long slender cylinder with uniform dielectric properties.

Blanchard, B. J.↗
NASA NTRS1991

Investigation of vortex development on a pitching slender body of revolution

A computational study of the unsteady flow about a pitching 3.5 caliber tangent ogive forebody is presented. The flow is simulated using the full 3D unsteady Navier-Stokes equations and a time-accurate implicit algorithm. Comparison to available experimental data for a steady 20 deg case is presented as validation. Effects of grid resolution and a comparison of solutions using full Navier-Stokes and the thin-layer approximation are included. The forebody is simulated in a 'pitch-up to 20 deg and hold' maneuver, and two different pitch axis locations are used in the study. Examination of the unsteady vorticity field for the pitch-up cases reveals the formation of strong shear layers as the body decelerates, and their roll-up into vortical structures in a process similar to that observed in airfoil dynamic stall. Pronounced vortex/surface interactions are seen which produce multiple secondary separation regions, ejection of vorticity from the surface, and embedded regions of high suction.

Stanek, M. J.↗
NASA NTRS1975

ISOFINEL: Isoparametric finite element code for elastic analysis of two-dimensional bodies

A formulation is presented for the development of a finite element program for the elastic analysis of two-dimensional bodies using the eight-node isoparametric quadrilateral. The program solves for both plane stress and plane strain problems. The finite element formulation based on the isoparametric displacement functions is presented. The program structure is given in the form of flow diagrams with descriptions of the numerical procedure used to obtain the element stiffness matrix, and the solution method employed to solve for nodal displacements. Three numerical examples (a plate under uniaxial tension, a plate under pure shear, and a beam under pure bending) are presented to illustrate the capability and limitations of the element implementation. The first problem is solved exactly by the element, as predicted by the form of its displacement functions. In the other two problems the accuracy of the solution is highly dependent upon the slenderness of the element, the number of elements in the map, and the numerical integration scheme used to build the element stiffness matrix.

Marino, C.↗
NASA NTRS1984

Usefulness of multifrequency MST radar measurements, part 2.6B

Scattering of radio waves from atmospheric refractive-index irregularities induced by turbulence was invoked almost four decades ago to explain the characteristics of signals received on VHF/UHF ionospheric and tropospheric forward-scatter links. Due to the bistatic geometry of these links a slender, horizontally extended, common volume or cell is formed in space. The principal contribution to scattering arises from refractive-index fluctuations in this volume at the Bragg wave number K approx. sub B = K approx. sub i -k approx. sub s vectors. It has been surmised that the use of more than one frequency in probing the middle-atmosphere regions should help resolve several issues pertaining to the scattering mechanism. These issues are briefly re-examined in this note. The implications of the radar equation are discussed. The problems arising due to layered structure of turbulence and the choice of frequencies most suitable for multifrequency measurements are considered.

Rastogi, P. K.↗
NASA NTRS1987

Flutter study of an advanced composite wing with external stores

A flutter test using a scaled model of an advanced composite wing for a Navy attack aircraft has been conducted in the NASA Langley Research Center Transonic Dynamics Tunnel. The model was a wall-mounted half-span wing with a semi-span of 6.63 ft. The wing had an aspect ratio of 5.31, taper ratio of 0.312, and quarter-chord sweep of 25 degrees. The model was supported in a manner that simulated the load path in the carry-through structure of the aircraft and the symmetric boundary condition at the fuselage centerline. The model was capable of carrying external stores from three pylon locations on the wing. Flutter tests were conducted for the wing with and without external stores. No flutter was encountered for the clean wing at test conditions which simulated the scaled airplane operating envelope. Flutter boundaries were obtained for several external store configurations. The flutter boundaries for the fuel tanks were nearly Mach number independent (occurring at constant dynamic pressure). To study the aerodynamic effect of the fuel tank stores, pencil stores (slender cylindrical rods) which had the same mass and pitch and yaw inertia as the fuel tanks were tested on the model. These pencil store configurations exhibited a transonic dip in the flutter dynamic pressure, indicating that the aerodynamic effect of the actual fuel tanks on flutter was significant. Several flutter analyses methods were used in an attempt to predict the flutter phenomenon exhibited during the wind-tunnel test. The analysis gave satisfactory predictions of flutter for the pencil store configurations, but unsatisfactory correlation for the actual fuel tank configurations.

Cole, Stanley R.↗
NASA NTRS1980

Structural sizing considerations for large space platforms

Structural optimization studies are made using mathematical programming techniques to examine minimum mass structural proportions of deployable and erectable tetrahedral truss platforms subject to the integrated effects of practical design requirements. Considerations integrated into the optimization process are: 1) lowest natural frequencies of the platform and individual platform components (struts); 2) packaging constraints imposed by the Shuttle cargo bay capacity; 3) initial curvature of the struts; 4) column buckling of the struts due to gravity gradient, orbital transfer, strut length tolerance, or design loads; and 5) practical lower limits for strut diameter and wall thickness. Ultra-low mass designs are shown to be possible with strut proportions much more slender than those conventionally used for earthbound application.

Heard, W. L., Jr.↗
NASA NTRS2004

Wind Tunnel Application of a Pressure-Sensitive Paint Technique to a Faceted Missile Model at Subsonic and Transonic Speeds

A pressure-sensitive paint (PSP) technique was applied in a wind tunnel experiment in the NASA Langley Research Center 8-Foot Transonic Pressure Tunnel to quantify the vortex-induced surface static pressures on a slender, faceted missile model at subsonic and transonic speeds. Global PSP calibrations were obtained using an in-situ method featuring the simultaneous electronically-scanned pressures (ESP) measurements. Both techniques revealed the significant influence leading-edge vortices on the surface pressure distributions. The mean error in the PSP measurements relative to the ESP data was approximately 0.6 percent at M(sub infinity)=0.70 and 2.6 percent at M(sub infinity)=0.90 and 1.20. The vortex surface pressure signatures obtained from the PSP and ESP techniques were correlated with the off-surface vortex cross-flow structures obtained using a laser vapor screen (LVS) flow visualization technique. The on-surface and off-surface techniques were complementary, since each provided details of the vortex-dominated flow that were not clear or apparent in the other.

Erickson, Gary E.↗
DOE OSTI2025

Assessment of integral models for non-Boussinesq lazy plumes using numerical simulations

Integral modelling of turbulent buoyant plumes is crucial for rapid predictions of plume characteristics. While the governing equations are typically derived using self-similarity and a Boussinesq approximation, these assumptions may not hold for plumes originating from finite-area sources with large density ratios. Here, this work evaluates the accuracy of integral-scale models for non-Boussinesq lazy plumes using high-fidelity numerical simulations of turbulent helium plumes. We analyse the plume kinematics by computing vertical fluxes, plume radius and radial profiles, establishing some disparities between common practice and physical accuracy. We identify how the definition of the plume radius changes the perception of the plume structure when the flow is not self-similar and derive a relationship between the flux-based and threshold-based definitions without requiring self-similarity. We then examine the plume dynamics by evaluating the source terms from the governing plume equations. Our results support neglecting diffusive and viscous effects but emphasise the importance of the mean pressure gradient, even in the self-similar regime. Two coefficients need to be modelled: the well-known entrainment coefficient and the lesser-known momentum correction coefficient, which is a correction required for the momentum equation to account for self-similar and slender approximations. The momentum correction coefficient is found to be approximately constant and slightly greater than the assumed value of 1. The standard entrainment coefficient models perform well up to a local Richardson number three times the asymptotic value but overpredict entrainment for larger Richardson numbers. We propose a correction using the known finite limit of entrainment at infinite Richardson number.

Meehan, Michael Alexander [Sandia National Laborat↗
NASA NTRS1997

An Experimental Investigation on the Static Equilibria and Dynamics of Liquid Bridges

A liquid bridge is a volume of liquid held between two or more solid supports. In the case of small disk supports with a sharp edge, the contact line between the bridge and the support disk will be anchored along the edge of the disk. For these cases the solid presents a geometrical singularity and the contact angle is indeterminate within a given range. This dissertation presents research conducted on liquid bridges with anchored contact lines. The three major topics covered are: determining the role of support geometry on static equilibria, liquid bridge dynamical behavior, and forces exerted by a liquid bridge on a support structure. The work was primarily experimental and conducted in a "Plateau tank" that allowed for the simulation of equivalent low-gravity conditions. The main thrust of the experimental work involved the use of a high resolution optical measurement system for imaging the dynamic zone shape, measurement of the static and dynamic contact angles and non-invasive analysis of excited surface modes. The liquid bridge was manipulated by computer controlled linear actuators which allowed precise control over the physical characteristics of the bridge. Experiments have been carried out to locate a bifurcation point along the maximum volume axisymmetric stability margin. Below the critical slenderness the bifurcation from an axisymmetric to a stable nonaxisymmetric configuration is supercritical. However, above this critical slenderness, the bifurcation is subcritical. A series of experiments analyzed the effect on axisymmetric bridge stability by using support disks of different radii, The shape behavior as transition points were approached, as well as the limiting case of a vanishing support radius was investigated. Experiments were performed to determine the resonant frequencies of axisymmetric bridges subject to lateral vibrations. Anomolous results led to a series of experiments to characterize nonlinearities present in the dynamic bridge shape. Finally, an attempt was made to experimentally measure the force exerted by the bridge on the lower support disk. This was done through use of a force balance apparatus. Particular attention was paid to the behavior of the bridge as the minimum volume stability limit was approached.

Resnick, Andrew Howard↗
NASA NTRS1974

Nonlinear equations of motion for the elastic bending and torsion of twisted nonuniform rotor blades

The equations of motion are developed by two complementary methods, Hamilton's principle and the Newtonian method. The resulting equations are valid to second order for long, straight, slender, homogeneous, isotropic beams undergoing moderate displacements. The ordering scheme is based on the restriction that squares of the bending slopes, the torsion deformation, and the chord/radius and thickness/radius ratios are negligible with respect to unity. All remaining nonlinear terms are retained. The equations are valid for beams with mass centroid axis and area centroid (tension) axis offsets from the elastic axis, nonuniform mass and stiffness section properties, variable pretwist, and a small precone angle. The strain-displacement relations are developed from an exact transformation between the deformed and undeformed coordinate systems. These nonlinear relations form an important contribution to the final equations. Several nonlinear structural and inertial terms in the final equations are identified that can substantially influence the aeroelastic stability and response of hingeless helicopter rotor blades.

Hodges, D. H.↗
NASA NTRS1986

Direct simulation of hypersonic flows over blunt slender bodies

Results of a numerical study of low-density hypersonic flow about cylindrically blunted wedges and spherically blunted cones with body half angles of 0, 5, and 10 deg are presented. Most of the transitional flow regime encountered during entry between the free molecule and continuum regimes is simulated for a reentry velocity of 7.5 km/s by including freestream conditions of 70 to 100 km. The bodies are at zero angle of incidence and have diffuse and finite catalytic surfaces. Translational, thermodynamic, and chemical nonequilibrium effects are considered in the numerical simulation by utilizing the direct simulation Monte Carlo (DSMC) method. The numerical simulations show that noncontinuum effects such as surface temperature jump, and velocity slip are evident for all cases considered. The onset of chemical dissociation occurs at a simulated altitude of 96 km for the two-dimensional configurations. Comparisons between the DSMC and continuum viscous shock-layer calculations highlight the significant difference in flowfield structure predicted by the two methods.

Moss, J. N.↗
NASA NTRS2003

An Assessment of CFD Effectiveness for Vortex Flow Simulation to Meet Preliminary Design Needs

The low-speed flight and transonic maneuvering characteristics of combat air vehicles designed for efficient supersonic flight are significantly affected by the presence of free vortices. At moderate-to-high angles of attack, the flow invariably separates from the leading edges of the swept slender wings, as well as from the forebodies of the air vehicles, and rolls up to form free vortices. The design of military vehicles is heavily driven by the need to simultaneously improve performance and affordability.1 In order to meet this need, increasing emphasis is being placed on using Modeling & Simulation environments employing the Integrated Product & Process Development (IPPD) concept. The primary focus is on expeditiously providing design teams with high-fidelity data needed to make more informed decisions in the preliminary design stage. Extensive aerodynamic data are needed to support combat air vehicle design. Force and moment data are used to evaluate performance and handling qualities; surface pressures provide inputs for structural design; and flow-field data facilitate system integration. Continuing advances in computational fluid dynamics (CFD) provide an attractive means of generating the desired data in a manner that is responsive to the needs of the preliminary design efforts. The responsiveness is readily characterized as timely delivery of quality data at low cost.

Raj, P.↗
NASA NTRS1962

Design comparison of lunar return configurations

Parabolic manned re-entry design comparisons are made between two classes of slender and blunt configurations capable of conventional horizontal and vertical earth landings. Aerodynamic modulation using flaps and control augmentation requirements are discussed in terms of their effect upon re-entry trajectories and landing footprints. Within the environment defined by the re-entry trajectories, the convective and radiative modes of heat transfer are compared, their differences discussed, and the problems associated with the configurations for planetary return missions indicated. Thermal protection systems are discussed and the factors influencing the selection of a given system for the re-entry environment are indicated. Comparison between reflective and absorptive systems are made and the merits of each for a given flight time indicated. A thermo-structural analysis is presented which shows the trade-oft between structural operating temperature and heat protection system thickness requirements. Total heat shield and structural weights are compared for the landing footprints presented and their variation with range shown. Finally, the areas of uncertainty in the aero-thermo structural design analysis are indicated for each class of configuration studied, and the weight differences between conventional horizontal landing and vertical descent configurations are given.

Parabolic flight↗
NASA NTRS1988

Slender wing theory including regions of embedded total pressure loss

An aerodynamic theory of the flow about slender delta wings is described. The theory includes a treatment of the self-consistent development of the vortex wake patterns above the wing necessary to maintain smooth flow at the wing edges. The paper focuses especially on the formation within the wake of vortex 'cores' as embedded regions of total pressure loss, fed and maintained by umbilical vortex sheets emanating from the wing edges. Criteria are developed for determining the growing size and location of these cores, as well as the distribution and strength of the vorticity within them. In this paper, however, the possibility of vortex breakup is omitted. The aerodynamic consequences of the presence and evolution of the cores and the associated wake structure are illustrated and discussed. It is noted that wake history effects can have substantial influence on the distribution of normal force on the wing as well as on its magnitude.

Mccune, James E.↗
NASA NTRS2001

Vortical Flow Prediction Using an Adaptive Unstructured Grid Method

A computational fluid dynamics (CFD) method has been employed to compute vortical flows around slender wing/body configurations. The emphasis of the paper is on the effectiveness of an adaptive grid procedure in "capturing" concentrated vortices generated at sharp edges or flow separation lines of lifting surfaces flying at high angles of attack. The method is based on a tetrahedral unstructured grid technology developed at the NASA Langley Research Center. Two steady-state, subsonic, inviscid and Navier-Stokes flow test cases are presented to demonstrate the applicability of the method for solving practical vortical flow problems. The first test case concerns vortex flow over a simple 65' delta wing with different values of leading-edge bluntness, and the second case is that of a more complex fighter configuration. The superiority of the adapted solutions in capturing the vortex flow structure over the conventional unadapted results is demonstrated by comparisons with the windtunnel experimental data. The study shows that numerical prediction of vortical flows is highly sensitive to the local grid resolution and that the implementation of grid adaptation is essential when applying CFD methods to such complicated flow problems.

Pirzadeh, Shahyar Z.↗
NASA NTRS2001

Vortical Flow Prediction Using an Adaptive Unstructured Grid Method

A computational fluid dynamics (CFD) method has been employed to compute vortical flows around slender wing/body configurations. The emphasis of the paper is on the effectiveness of an adaptive grid procedure in "capturing" concentrated vortices generated at sharp edges or flow separation lines of lifting surfaces flying at high angles of attack. The method is based on a tetrahedral unstructured grid technology developed at the NASA Langley Research Center. Two steady-state, subsonic, inviscid and Navier-Stokes flow test cases are presented to demonstrate the applicability of the method for solving practical vortical flow problems. The first test case concerns vortex flow over a simple 65deg delta wing with different values of leading-edge bluntness, and the second case is that of a more complex fighter configuration. The superiority of the adapted solutions in capturing the vortex flow structure over the conventional unadapted results is demonstrated by comparisons with the windtunnel experimental data. The study shows that numerical prediction of vortical flows is highly sensitive to the local grid resolution and that the implementation of grid adaptation is essential when applying CFD methods to such complicated flow problems.

Pirzadeh, Shahyar Z.↗
NASA NTRS2004

Wind Tunnel Application of a Pressure-Sensitive Paint Technique to a Faceted Missile Model at Subsonic and Transonic Speeds

A pressure-sensitive paint (PSP) technique was applied in a wind tunnel experiment in the NASA Langley Research Center 8-Foot Transonic Pressure Tunnel to quantify the vortex-induced surface static pressures on a slender, faceted missile model at subsonic and transonic speeds. Satisfactory global calibrations of the PSP were obtained at =0.70, 0.90, and 1.20, angles of attack from 10 degrees to 20 degrees, and angles of sideslip of 0 and 2.5 degrees using an in-situ method featuring the simultaneous acquisition of electronically-scanned pressures (ESP) at 57 discrete locations on the model. Both techniques clearly revealed the significant influence on the surface pressure distributions of the vortices shed from the sharp, chine-like leading edges. The mean error in the PSP measurements relative to the ESP data was approximately 0.6 percent at M infinity =0.70 and 2.6 percent at M infinity =0.90 and 1.20. The vortex surface pressure signatures obtained from the PSP and ESP techniques were correlated with the off-surface vortex cross-flow structures obtained using a laser vapor screen (LVS) flow visualization technique. The on-surface and off-surface techniques were complementary, since each provided details of the vortex-dominated flow that were not clear or apparent in the other.

Erickson, Gary E.↗