Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solid additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

FY24 Task 5: Leachate Disposition

Directly feeding sludge solids to the high-level waste (HLW) Waste Treatment Plant represents an alternative flowsheet seeking to initiate sludge processing as soon as possible. Key processing functions previously captured during baseline pretreatment operations include leaching and washing prior to solids concentration. These operations should be considered in the potential direct feed flowsheets to maximize waste feed loading, minimize HLW volume, and mitigate corrosion challenges associated with vitrification of high phosphate and fluoride concentrations. Additionally, single-shell tank (SST) retrievals and waste transfers to double-shell tanks (DSTs) in a direct feed flowsheet would likely also benefit from some level of leaching, washing, and solids concentration in order to reduce DST space and mission duration. These operations could occur in a new facility or potentially in available DSTs. If washing and leaching are utilized, an effective disposition pathway for the wash water and leachate solutions are needed. Three target species that benefit significantly from leaching and washing are phosphate, fluoride and aluminum. Phosphate (PO 4 3- ) and fluoride (F - ) can contribute substantially to the amount of carrier fluid needed for dissolution, and the resulting volume of liquid generated. Disposition of this retrieval solution should be evaluated in order to prevent crystallization of these anions throughout system processing. Since there is a high probability that any retrieval solutions will be at or near their PO 4 3- and F - solubility limits, evaporation or blending with a high Na supernate (>3.5 M) is not recommended for the wash water streams without a method to remove precipitants prior to solution disposal. Additionally, aluminum present in the southeast quadrant of the Hanford site represents roughly 60% of the waste solids in the initial processing tanks. These aluminum solids are in the form of gibbsite (Al(OH) 3 ) and can pose significant challenges for processing due to the fast-settling times and high solids loading associated with these materials. Easily remediated by caustic addition to the solids, these wash solutions could be processed through crystalline silicotitanate (CST) ion exchange columns to prepare the supernate solutions for disposition. The current target for feed conditions to the Low Activity Waste (LAW) melter are waste streams that contain nominally 5-6 M Na. Fractions within the tanks contain upwards of 0.2 M phosphate and fluoride in solution at 3.5 M Na. Concentrating these solutions above 5 M Na would result in an exceedance of the solubility limits, and potential for uncontrolled precipitation of the phosphate and fluoride crystal material. The resulting crystalline salt material is typically sodium fluoride phosphate, also referred to as natrophosphate (Na 7 FPO 4 ·19H 2 O). Salt phases are of importance in tank waste due to their chemical reactivity, which can result in precipitation, dissolution, or transformation, impacting any downstream processes (Bolling et al. 2020, Russell, Snow, and Peterson 2010). Salt generation and precipitation could pose challenges by causing system plugging and melter corrosion if left in the supernate stream, or limit sodium molarity of the supernate that would be accepted without incident in waste operations. To understand the impact of this salt generation, the crystallization of natrophosphate in multiple simulant feed matrices was studied to understand the implications of various tank waste supernate chemistries. Three matrices were examined: high PO 4 3- /low F - , low PO 4 3- /high F - , and an average matrix. Subsequent testing was performed with the average matrix with the inclusion of CsNO 3 , and a final run with the average matrix including CsNO 3 and a 137 Cs spike for tracer purposes.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Tunable and Robust Optical and Structural Properties of a Cooperative Squaraine-Dye Aggregate-DNA DX-DAE Tile System

Molecular excitons, which are excitations delocalized over multiple dyes in a wavelike manner, are of interest for a wide range of applications, including quantum information science. Numerous studies have templated a variety of synthetic dyes via a DNA scaffold to induce dye aggregation to create molecular excitons upon photoexcitation. Dye aggregate optical properties are critically dependent on relative dye geometry and local environment; therefore, an understanding of dye-dye and DNA-dye interactions is critical for advancing toward more complex DNA-dye systems. The extensively studied DNA Holliday junction (HJ) and less-studied double-crossover (DX) tile motif are fundamental test beds for designing complex and ultimately modular DNA-dye architectures. Here, we report the first study of single-linked squaraine dye aggregation and exciton delocalization on a larger and more stable (compared with the HJ) DX tile motif. We first highlight a few DNA-dye constructs that support single dyes and aggregates with distinct optical properties that are both tunable—through sample design, buffer conditions, and heat treatment—and robust to environment changes, including transfer to solid phase. Next, we assess several experimental and design considerations that demonstrate directed dye-driven assembly of a novel double-tile DNA configuration. Our results demonstrate that single-linked squaraine dyes templated to DX tiles provide a viable research path to design and evaluate dye aggregate networks that support exciton delocalization. We include herein the first report of exciton delocalization in the solid phase in a DNA-dye construct. Additionally, our findings indicate that dye aggregation impacts the assembly of the DNA-dye construct, and, in some cases, thereby cooperates with the DNA to determine a final robust system configuration. Finally, we show that a controlled annealing schedule can be employed to promote the homogeneous assembly of DNA-dye constructs. The findings in this study contribute to the understanding of DNA-dye systems and the relevant factors involved in their directed assembly to achieve specific constructs with desirable properties.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Multinuclear Solid-State NMR and NMR Crystallography of Solid Forms of Creatine and Creatinine

Creatine is a performance-enhancing supplement with two widely available commercial solid forms, namely, creatine monohydrate (creatine·H 2 O) and creatine HCl, the latter of which does not have a reported crystal structure. Moreover, commercial formulations of creatine may contain creatinine, an undesired impurity phase resulting from the self-cyclization of creatine during manufacturing. Therefore, reliable methods for characterizing the different solid forms of creatine and detecting the presence of creatinine are essential. Herein, we address these challenges using 13 C, 15 N, and 35 Cl solid-state NMR (SSNMR) spectroscopy to obtain distinct spectral fingerprints for creatine·H 2 O and creatine HCl, along with creatinine and creatinine HCl. The acquisition of these SSNMR spectra offers a robust approach for both the rapid characterization of each solid form and the detection of the impurity phases. Additionally, quadrupolar NMR crystallography-guided crystal structure prediction (QNMRX-CSP) was applied for the de novo crystal structure determination of creatine HCl, which was validated by the subsequently determined single-crystal X-ray diffraction (SCXRD) structure. Finally, to investigate the relationship between NMR parameters and structural features, 13 C and 15 N chemical shifts and 35 Cl electric field gradient (EFG) tensors were computed from geometry-optimized structures of the four solid forms by using dispersion-corrected DFT-D2* methods. Finally, this integrative approach offers a powerful framework for advancing the structural understanding and quality control of creatine-based supplements and next-generation formulations, as well as a wide range of other solid pharmaceuticals and nutraceuticals.

NMR↗
DOE OSTI2026

Electrode Modification by Laser Ablation to Overcome Mechanical and Scalability Limitations of Solid-State Prealkylation of Electrode Architectures

In this work, laser ablation of Si electrode surfaces is utilized to provide localized strain relief during the Solid State Prealkylation of Electrode Architectures (SPEAR) process, in addition to volumetric expansion relief in the form of free volume channels across the electrode. A hexagonal mesh patterning was employed via laser ablation, where the hexagonal diameter (pitch) was varied from 250 to 1000 µm. It was demonstrated that these channels serve as expansion voids, accommodating the increase in electrode thickness observed during SPEAR and preventing cracking at the electrode surface. Optical microscopy and Raman mapping confirm that Li diffusion is the rate-limiting solid-state process, requiring a 24 h rest period to achieve homogeneous LixSi alloying through the electrode bulk. Electrochemical evaluations in full cells show that a 1000 μm pitch pattern yields a high initial discharge capacity of 2485 mA h g–1 and 86.4% capacity retention after 80 cycles, whereas smaller pitches (<500 μm) result in lithium plating at 4.1 V in full cells paired with NMC 811 due to excessive current collector exposure from the ablation process. XPS analysis reveals that the laser treatment modifies the electrode surface by increasing the Si–O and C–O species, changing the SEI composition observed via an increase in fluorophosphates upon cycling.

Musgrove, Amanda [ORNL] (ORCID:0009000220910389)↗
DOE OSTI2026

Tank 11H Low Temperature Aluminum Dissolution and Inhalation Dose Potential Analyses at Savannah River Site – 26018

Currently, there is approximately 34 million gallons of high-level radioactive tank waste in the Tank Farm at the Savannah River Site (SRS). The ultimate goal of operations at the Tank Farm is to remove the high level waste (HLW) from the tanks followed by stabilization of the waste through vitrification of the HLW into glass or grouting the decontaminated waste into saltstone. After bulk removal of the HLW consisting of sludge, saltcake, and supernatant, further efforts are made to reduce the residual waste present in the tank in order to declare preliminary cease waste removal (PCWR) signifying completion of HLW removal. These reduction efforts can include tank washing to remove soluble salts and radioisotopes and dissolution of solids including aluminum. Aluminum in the form of gibbsite and boehmite is relatively insoluble in water. Through addition of aqueous sodium hydroxide, the aluminum can be dissolved at mild temperatures. In order for the waste tank to meet closure mode requirements of the Concentration, Storage, and Transfer Facilities (CSTF), which includes the Tank Farm, Documented Safety Analysis (DSA), a component of the safety basis, the inhalation dose potential (IDP) and the radiolytic hydrogen generation rate of the stored waste must be demonstrated to be lower than their respective designated limits. These parameters are calculated from measured radiochemical analyses of isotopes that emit a high amount of radioactivity including Cs-137, Sr-90, Pu-238, Pu-239, Pu-240, Pu-241, Am-241, and Cm-244. Following the low temperature aluminum dissolution (LTAD) process, Tank 11H slurry samples were pulled from the tank and sent to Savannah River National Laboratory (SRNL) to measure the extent of aluminum dissolution, hydroxide concentration, densities of slurry and supernatant, weight percent solids analyses, and radionuclide activities. The analyses of the composite sample found that approximately 90% of the total aluminum in the slurry was dissolved, indicating successful reduction of the insoluble aluminum in the waste tank. Additionally, the weight percent insoluble solids (slurry basis) measurement of the composite sample was found to be approximately 1%, demonstrating that minimal solids still remain in the tank. Finally, the radiochemical analyses of the composite sample determined that the waste contents of the tank met the IDP and radiolytic hydrogen generation rate requirements of the CSTF DSA. These measurements have shown that the LTAD process in Tank 11H was successful in waste reduction efforts and a positive step towards declaring PCWR and tank closure at SRS.

Dekarske, John [Savannah River National Laboratory↗
DOE OSTI2025

Microstructure-sensitive mechanical behavior of an additively manufactured psuedoelastic shape memory alloy

The additive manufacturing of shape memory alloys into complex geometries enables fabrication of advanced functional systems across a variety of fields and domains. This work presents results focused on the mechanical behavior of additively manufactured shape memory pseudoelastic NiTi. The deformation induced solid state phase transformation from austenite to martensite allows this system to accommodate large recoverable strains. This deformation behavior is fundamentally driven by crystal-scale transformation physics. Laser powder bed fusion processing reveals that the resulting microstructure, both grain morphology and crystallographic texture, is strongly dependent on the manufacturing processing history. Exhaustive mechanical testing demonstrates that these microstructural factors strongly impact both tensile and cyclic stress–strain behavior. Cyclic dissipative behavior, however, is similar across all tested microstructures following an initial transient period. Remarkably, analysis of spatial strain fields during tensile loading reveals two distinctly different localization “modes”. The first is initiation of localized deformation bands which continuously propagate through the tensile bar during loading. In the second mode localization is observed but lacks propagation; instead additional localization cites nucleate during subsequent loading. The latter phenomena is suspected to be driven by grain-scale deformation physics as the localized band morphologies coincide with grain morphologies. These phenomena strongly impact the resulting aggregate stress–strain behavior. Hence, manufacturers and designers of psuedoelastic functional components must at the very least consider the potential variability in properties when considering additive manufacturing processing. More ideally the process–structure–property relations can be used to further tailor and optimize final functional performance.

Additive manufacturing↗
DOE OSTI2024

In-situ electrochemical optical techniques in the investigation of lithium interfacial phenomena with a liquid and a solid-state electrolyte

An in-situ electrochemical optical diagnosis is the key to the investigation of electrode interface during a redox reaction. Because the morphology changes particularly, dendrite formation, dendrite shapes, solid electrolyte interface formation and gas generation can be revealed visually. The challenge of ensuring uniform current density on a flat Li anode in a liquid electrolyte was addressed and uniform Li plating was demonstrated. The dendrite shape change under different reduction current density was discussed. Here the Li dendrite shape change and the performance of Li anodes with a surface lamination of graphite and red phosphate were used as examples to demonstrate the capability of the in-situ optical cell. An in-situ electrochemical optical cell used in the investigation of the increasingly popular solid-state Li batteries has its own challenges. Due to the untransparent nature of a solid-state electrolyte, an optical investigation on a solid-state electrolyte Li battery needs to be done by exposing the cross-section of the cell. In addition, it is very difficult to assemble an optical cell with a brittle and fragile solid-state electrolyte in a glove box. A set of formation and transfer dies, and an optical cell were introduced. The Li dendrite growth at the interface can be observed in a solid-state Li cell.

25 ENERGY STORAGE↗
DOE OSTI2025

Investigation of Undissolved Solids from Salt Waste Processing Facility (SWPF) Salt Batches Collected via Filtration

SRNL researchers performed six experiments wherein 0.1 μm-grade stainless steel filters were used to filter samples pulled from salt batches 6, 9B, and 11B, without the addition of monosodium titanate. Three of these experiments were performed to collect filterable solids from each salt batch and characterize trapped solids via scanning electron microscopy. The remaining three experiments were performed to collect and then dissolve the same solids using 3.5 M nitric acid (similar to that employed in the Salt Waste Processing Facility) for characterization via Inductively-coupled plasma atomic emission spectroscopy.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Development of an Energy-Efficient and High-Productivity Ammonia Recovery and Removal Process Using Resin-Wafer Electrodeionization

As efforts to develop various energy resources, ammonia energy is emerging as a promising carbon-free fuel alternative. Recovering high-concentration ammonia and ammonium from wastewater potentially offers significant environmental and economic benefits. However, research on recovery technologies for industries such as semiconductors remains limited. This study develops an efficient, energy-saving ammonia recovery technology using Resin Wafer Electrodeionization (RW-EDI), specifically for the semiconductor industry. RW-EDI shows promise for recovering ammonia from high-concentration wastewater. By optimizing parameters, such as voltage and initial concentration, a balance between productivity and energy consumption is achieved. Results indicate that ammonium and fluoride ion transport kinetics are similar, with minimal competition and selectivity values between 0.95 and 1.08. As the initial ammonia/ammonium concentration increases from 500 to 8000 ppm, reaction rate constants and the overall mass transfer coefficient decrease. Increasing the voltage can enhance mass transfer and eliminate barriers. Ion transport primarily occurs in the RW solid phase, accounting for 93.89% of the total current. Additionally, RW-EDI shows superior specific energy consumption within a concentration range of 500 ppm to 8000 ppm, outperforming technologies like electrodialysis by reducing specific energy consumption from 8−15 kWh/kg-NH 4 + to 1.2−2.5 kWh/kg-NH 4 + . This study highlights RW-EDI’s potential for ammonia recovery, providing valuable insights for future applications in wastewater treatment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Defect-Free Growth of Decagonal Quasicrystals around Obstacles

Quasicrystals are aperiodic solids with exotic physical properties. The mechanisms driving their growth are far from understood, particularly in the presence of rigid obstacles. Here, using in situ synchrotron x-ray tomography and molecular dynamics simulations, we investigate the interaction between decagonal quasicrystals and obstacles (shrinkage pores) during solidification of an Al 79 ⁢Co 6 ⁢Ni 15 alloy. The results reveal defect-free quasicrystal growth around the pores, independent of pore size and geometry. Our findings point to a universal feature of aperiodic solids: their ability to accommodate structural disruptions due to additional (phasonic) degrees of freedom. This Letter opens new possibilities for synthesizing large-scale, single quasicrystals from a liquid metal precursor.

alloys↗
DOE OSTI2025

Mitigating Crack Formation When Using High Oxygen Permeability Ionomer in PEMFC Catalyst Layers

High oxygen permeability ionomers (HOPIs) are being developed as an alternative to conventional perfluorosulfonic (PFSA) ionomers for cathodes in proton exchange membrane fuel cells (PEMFCs). HOPIs aim to reduce local oxygen transport resistance, improving performance and reducing degradation as the catalyst loses surface area. However, HOPIs' more rigid, 3D backbone leads to increased crack density in the cathode, potentially causing accelerated degradation. This study investigates crack formation in HOPI-based and PFSA-bound catalyst layers (CLs). We conducted a comprehensive parametric study to identify conditions and catalyst slurry components that minimize cracking. CLs were fabricated with various ionomer and catalyst types, under different relative humidity (RH) levels, solids weight percentages, solvent ratios, and ionomer-to-carbon ratios (I/C). Results show that HOPI-based CLs exhibit less cracking when fabricated under low RH conditions, with lower solids weight percentage, higher alcohol content, and lower I/C. Additionally, catalysts with low/medium surface area carbon supports show less cracking than those with high surface area carbon supports.

08 HYDROGEN↗
DOE OSTI2024

Effects of electron beam irradiation on CrMnV and CrMnTiV high entropy alloys: Nano-mechanical, structural, and thermodynamic perspectives

Beam exit windows are crucial components of any particle accelerator as they provide an interface between the beamline vacuum and target material at atmospheric media. For high beam power machines, special materials and designs are required to withstand high radiation and mechanical loads, while minimizing energy loss during transition and maximizing window lifetime. This research investigates the impact of electron beam exposure to bulk CrMnV and CrMnTiV high entropy alloys (HEAs) with the primary goal of identifying suitable candidate materials for the design of robust and durable exit window settings. The selection criteria include intrinsic characteristics, power dissipation, and mechanical responses. According to the thermodynamic calculations, both equiatomic CrMnV and the addition of 7% of Ti with equiatomic CrMnV yield solid-solutions phases. The structural and mechanical properties of CrMnV and CrMnTiV samples were tested using field emission scanning electron microscopy, atomic force microscopy, scanning electron microcopy with energy dispersive x-ray spectroscopy, x-ray diffraction, and nanoindentation before and after exposure to a dose of ~66 kGy from a 10 MeV e-beam accelerator. Despite exhibiting beam transmission characteristics comparable to Cr and V, the indentation hardness of HEAs exceeded that of the Cr and V samples by five to six times. The examination of the CrMnTiV irradiated samples revealed organized deformation patterns depicting new features, which we suspect twinning and twin boundaries due to the addition of Ti to CrMnV. Ti, a hexagonal-close-packed crystal structure, is commonly known for deformation twinning behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2024

UHT-CAMANCHE: Ultra-High Temperature Ceramic Additively Manufactured Compact Heat Exchangers

The conceptual basis for this project is the convergence of advanced ultra-high temperature ceramic materials and additive manufacturing technologies to produce compact ceramic heat exchangers with complex internal flow path geometries. Task areas were broadly divided into materials and manufacturing development, heat exchanger design, component testing, and techno-economic analysis. Technical challenges included the design and commissioning of new test facilities, improving feature resolution and deposition rate of ceramic additive manufacturing techniques, establishing process-structure-property relationships in additively manufactured ultra-high temperature ceramics, and assessing high temperature materials compatibility in CO 2 environments. The primary candidate material evaluated in this work is a composite comprising zirconium diboride (ZrB2) with 30 vol. % silicon carbide (SiC) which was selected based on its desirable combination of high temperature mechanical properties, high thermal and electrical conductivities, and oxidation resistance. High solids loaded ZrB2-SiC pastes suitable for extrusion-based additive manufacturing were developed for the first time as part of this work. Materials compatibility studies indicate this material oxidizes in CO 2 to form a protective borosilicate scale which transforms to pure silica above 1000°C. Parts made by additive manufacturing displayed enlarged grain sizes produced by pressureless sintering as compared to hot-press sintering. Increases in microstructural coarseness have outsized effect on oxidation performance up to 1400°C due to incomplete oxidation of coarse large diameter SiC particles resulting in lower amounts of silica that apparently inhibit protective scale formation. Additive manufacturing as a forming technique did not appear to significantly affect thermal conductivity, hardness, or elastic modulus, though flexural strength was reduced by half or more as compared to traditionally hot-pressed materials. This effect was attributed to the presence of strength-limiting flaws (ca. 40 microns in size) originating from extrudate inhomogeneities that could potentially be eliminated with further process improvements. Attempts to attain economies of scale for production of multi-kilowatt scale heat exchangers by ceramic additive manufacturing proved difficult. Lack of automation and a modest extrusion rate while retaining fine feature resolution made the overall process labor intensive and limited experimental throughput. A number of full-scale components were taken through post-process heat treatments including drying, binder burnout, and sintering; however, none survived without significant flaws or cracks. Therefore, no operational data from a newly installed heat exchanger test loop were able to be obtained during the performance period. Continued research and development is recommended to improve economic feasibility of ceramic additive manufacturing by standardizing the use of advanced sensors, artificial intelligence, and automation tools to reduce associated labor costs and accelerate production rates. The materials and manufacturing techniques demonstrated in this work are likely to find applications in defense and energy applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Improving creep resistance of Al-0.27Zr-0.08Sn (wt%) via cold swaging while maintaining high electrical conductivity

This study investigates the effect of mechanical cold work (0, 50, and 90% cross-sectional area reduction via swaging) on the creep properties of cast aluminum alloys with high electrical conductivity including high-purity Al (HP-Al), Al-0.15Zr (Al-Zr), and Al-0.27Zr-0.08Sn (Al-Zr-Sn, wt%). The Al-Zr alloy is strengthened by Zr in solid solution while the Al-Zr-Sn alloy is additionally strengthened by Al3Zr nanoprecipitates (8 nm diameter). After 90% cold swaging, the alloys exhibit grains elongated along the swaging direction with their widths ranging between 8 and 152 μm perpendicular to the swaging direction. Creep testing at 200 °C shows that the minimum creep rate of all 90% swaged alloys shows high sensitivity to stress, which can be modeled via a threshold stress σth. Increasing swaging magnitude from 0 to 50 to 90% in Al-Zr-Sn improves the creep resistance without reducing electrical conductivity. The formation of subgrains, increased dislocation density, and columnar grain structure in swaged alloys all enhance creep resistance. HP-Al swaged to 90% exhibits much lower creep resistance (σth = 18 MPa) due to subgrain coarsening and the absence of precipitates compared to Al-Zr (σth = 40 MPa) and Al-Zr-Sn (σth = 40 MPa), which maintain stable subgrain structures and benefit from solid solution strengthening and Al3Zr nanoprecipitates, respectively. Although Al3Zr precipitates are known to stabilize the deformed microstructure by pinning grain-boundaries, this work demonstrates that Zr in solid solution alone can effectively stabilize the deformed microstructure resulting in enhanced creep resistance. This effect of Zr solute on stabilizing grain boundaries for creep performance was not previously well-defined in the literature. Despite similar creep performances of Al-Zr and Al-Zr-Sn, the latter shows 70% higher room-temperature microhardness and slightly improved electrical conductivity (56%IACS (International Annealed Copper Standard) vs. 57%IACS, respectively). This work provides new insights into creep mechanisms of cold-worked Al–Zr alloys that will guide the design of heat-resistant Al conductors for high-demand applications.

Coello ramirez, Ismael [Northwestern University,]↗
DOE OSTI2026

Unraveling interphase-driven failure pathways in LiMn0.6Fe0.4PO4/graphite pouch cells

LiMnxFe1−xPO4 (LMFP) is a promising high-voltage, thermally stable, and earth-abundant cathode material, yet its practical application is limited by interphase instability and Mn dissolution. In this work, we systematically evaluate LiMn0.6Fe0.4PO4/graphite pouch cells using three electrolyte formulations including control carbonate electrolyte, control + 2 wt% vinylene carbonate (VC), and control + 2 wt% VC + 1 wt% 1,3,2-dioxathiolane 2,2-dioxide (DTD), to establish how electrolyte composition governs interphase chemistry and long-term degradation. Electrochemical testing shows that both additives are preferentially reduced prior to ethylene carbonate (EC) during cell formation, generating robust cathode-electrolyte interphase (CEI) and solid-electrolyte interphase (SEI) layers that suppress gas evolution and raise the first-cycle coulombic efficiency to 89.3%. Additionally, the dual-additive electrolyte delivers the most stable performance, retaining over 85% capacity after 600 cycles while minimizing impedance growth under long-term cycling at C/3 and 40 °C. Soft X-ray absorption spectroscopy confirms that VC + DTD effectively suppresses electrolyte oxidation at the cathode surface, and micro-X-ray fluorescence shows substantially reduced Mn dissolution and deposition on the graphite anode. Density functional theory simulations further provided insights into the structural and energetic influences of alkoxide species on the cathode surface, proposing a Mn2+ extraction mechanism. The combined experimental and computational findings establish a mechanistic link between electrolyte composition and interphase evolution, highlighting the effectiveness of electrolyte engineering for extending the operational lifetime of LMFP-based lithium-ion batteries.

Chak, Chanmonirath Michael↗
DOE OSTI2024

Enhancing the Range and Reliability of the Spacer Layer Imaging Method

The spacer layer imaging method (SLIM) is widely used to measure the thickness of additive and lubricant films, in lubricant development and evaluation, and for fundamental research into elastohydrodynamic lubrication and tribofilm formation mechanisms. The film thickness measurement, as implemented on several popular tribometers, provides powerful, non-destructive in-situ mapping of film topography with nanometre-scale height sensitivity. However, the results can be highly sensitive to experimental procedure, machine condition, and image analysis, in some cases reporting unphysical film thickness trends. The prevailing image analysis techniques make it challenging to interrogate these errors, often hiding their multivariate nonlinear behaviour from the user by spatial averaging. Herein, several common ‘silent errors’ in the SLIM measurement, including colour matching to incorrect fringe orders, and colour drift due to the optical properties of the system or film itself, are discussed, with examples. A robust suite of novel a priori and a posteriori methods to address these issues, and to improve the accuracy and reliability of the measurement, are also presented, including a novel, computationally inexpensive circle-finding algorithm for automated image processing. In combination, these methods allow reliable mapping of films up to at least 800 nm in thickness, representing a significant milestone for the utility of SLIM applied to elastohydrodynamic contact.

EHL film geometry↗
DOE OSTI2025

Aggregation Dynamics of Colloidal Particles in Tin Perovskite Crystalline Film Formation

We present an approach to understanding the crystallization of tin-based perovskite films for photovoltaic applications, starting from precursor suspensions processed via spin-coating. By integrating colloidal theory with the fluid dynamics of suspensions, this approach elucidates the influence of both chemical variables and process parameters on the crystallization pathways of perovskite suspensions and the resulting microstructural features of the solid films. Specifically, the incorporation of SnCl 2 as an additive was found to accelerate crystallization, whereas tBP induces a slowdown of the process leading, however, to a marked improvement in film uniformity and microstructural quality.

Crystallization↗
DOE OSTI2024

Analytical capabilities for iodine detection: Review of possibilities for different applications

This Review summarizes a range of analytical techniques that can be used to detect, quantify, and/or distinguish between isotopes of iodine (e.g., long-lived 129 I, short-lived 131 I, stable 127 I). One reason this is of interest is that understanding potential radioiodine release from nuclear processes is crucial to prevent environmental contamination and to protect human health as it can incorporate into the thyroid leading to cancer. It is also of interest for evaluating iodine retention performances of next-generation iodine off-gas capture materials and long-term waste forms for immobilizing radioiodine for disposal in geologic repositories. Depending upon the form of iodine (e.g., molecules, elemental, and ionic) and the matter state (i.e., solid, liquid, and gaseous), the available options can vary. In addition, several other key parameters vary between the methods discussed herein, including the destructive vs nondestructive nature of the measurement process (including in situ vs ex situ measurement options), the analytical data collection times, and the amount of sample required for analysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗