Search NASA⌕ Search

SEARCH · Search NASA

Results for “Structure modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Accuracy of derivatives of control performance using a reduced structural model

The sensitivity of control system performance to structural changes is calculated for a multi-span beam with direct-rate feedback vibration control. Reduced models based on the natural modes of the structure are formed and derivatives of the damping ratios of the closed-loop eigenvalues are calculated. The convergence of the derivatives of the damping ratios with increasing number of modes is shown to be slower than the convergence of the damping ratios themselves. In particular, in some cases the convergence of finite-element approximations to the derivatives is much faster than the convergence of the modal approximations. The results indicate that the use of reduced models based on natural vibration modes may be ill-advised for calculating the sensitivity of control system performance to changes in the controlled structure.

Sandridge, Chris A.↗
NASA NTRS2013

A Structural Model Decomposition Framework for Systems Health Management

Systems health management (SHM) is an important set of technologies aimed at increasing system safety and reliability by detecting, isolating, and identifying faults; and predicting when the system reaches end of life (EOL), so that appropriate fault mitigation and recovery actions can be taken. Model-based SHM approaches typically make use of global, monolithic system models for online analysis, which results in a loss of scalability and efficiency for large-scale systems. Improvement in scalability and efficiency can be achieved by decomposing the system model into smaller local submodels and operating on these submodels instead. In this paper, the global system model is analyzed offline and structurally decomposed into local submodels. We define a common model decomposition framework for extracting submodels from the global model. This framework is then used to develop algorithms for solving model decomposition problems for the design of three separate SHM technologies, namely, estimation (which is useful for fault detection and identification), fault isolation, and EOL prediction. We solve these model decomposition problems using a three-tank system as a case study.

Roychoudhury, Indranil↗
NASA NTRS1983

Structural modelling and control design under incomplete parameter information: The maximum-entropy approach

A stochastic structural control model is described. In contrast to the customary deterministic model, the stochastic minimum data/maximum entropy model directly incorporates the least possible a priori parameter information. The approach is to adopt this model as the basic design model, thus incorporating the effects of parameter uncertainty at a fundamental level, and design mean-square optimal controls (that is, choose the control law to minimize the average of a quadratic performance index over the parameter ensemble).

Hyland, D. C.↗
DOE OSTI2024

STRUCTURAL MODELING TO SUPPORT POST-YIELD ACCEPTANCE CRITERIA FOR SPENT NUCLEAR FUEL CLADDING

Spent nuclear fuel (SNF) is evaluated for structural failure during storage and transportation scenarios. The U.S. Department of Energy’s Spent Fuel and Waste Science and Technology (SFWST) program has sponsored significant research in quantifying mechanical loads on SNF during storage and transportation scenarios using experimental and modeling methods. The SFWST program has also performed significant research on measuring the mechanical behavior of irradiated SNF as defueled cladding segments and cladding with fuel pellets to measure composite behavior. This paper considers some of the key material data from the Sibling Pin testing and uses structural modeling and analysis methods that have been informed by testing to consider post-yield acceptance criteria for SNF cladding structural analysis. Test data published by Oak Ridge National Laboratory (ORNL) and Pacific Northwest National Laboratory (PNNL) are the foundation for informing the material behavior of the models developed in this study. In particular, four-point bend (4PB) tests of fueled and defueled cladding segments provide significant information about the bending failure mode of SNF. ORNL’s 4PB test data is on fueled cladding segments, so the composite behavior of SNF is demonstrated. This paper describes PNNL’s coincident beam model that was developed to approximate the composite behavior of SNF. This paper also presents PNNL’s structural dynamic finite element models of a cask tip-over scenario, which is predicted to cause the strongest mechanical loads on SNF of all postulated storage and transportation scenarios. SNF bending loads predicted in the cask tip-over scenario and cladding acceptance criteria beyond yield are considered, with justification based on the Sibling Pin test data. ASME Boiler and Pressure Vessel code stress intensity limits are also considered. The ultimate goal of this work is to aid in the justification of structural acceptance criteria for SNF cladding beyond the cladding’s irradiated yield strength for use in structural analysis of all storage and transportation scenarios.

Klymyshyn, Nicholas A.↗
NASA NTRS1988

Emulating a flexible space structure: Modeling

Control Dynamics, in conjunction with Marshall Space Flight Center, has participated in the modeling and testing of Flexible Space Structures. Through the series of configurations tested and the many techniques used for collecting, analyzing, and modeling the data, many valuable insights have been gained and important lessons learned. This paper discusses the background of the Large Space Structure program, Control Dynamics' involvement in testing and modeling of the configurations (especially the Active Control Technique Evaluation for Spacecraft (ACES) configuration), the results from these two processes, and insights gained from this work.

Waites, H. B.↗
NASA NTRS1986

Vertical cloud structure models for the NTRZ EQZ, SEB and STRZ of Jupiter

Latitude-dependent models of the vertically inhomogeneous Jovian cloud structure are presented. The models assume an atmospheric composition with (CH4)/(H2) = 2.0 x .003, (He)/(H2) = 0.11 and (NH3)/(H2) = 2.0 x .0004 consistent with the Voyager IRIS measurements and employ refractive indices appropriate for ammonia ice particles and a photochemical stratospheric aerosol layer. The free parameters of the models are determined by fitting the results of multiple, scratching calculations to the near-infrared center and limb spectra of Clark and McCord and the center-to-limb 6190, 6350, 7250, 7500, 8900 and 9500 A photometric measurements of West. The resulting synthetic center-to-limb profiles are in excellent agreement with the observations. Of the regions studied the tropical zones are the most similar, with the observed differences explained by variations in the vertical extent of the cloudy layers. The Equatorial Zone is a unique region with denser NH3 clouds than either of the tropical zones. At visible and near-infrared wavelengths the belt-zone contrasts can be explained by opacity differences. The optical depth of the stratospheric aerosol layer is larger in a belt, while the tropospheric clouds are deeper and thinner.

Carlson, B. E.↗
NASA NTRS2011

Reference Management Methodologies for Large Structural Models at Kennedy Space Center

There have been many challenges associated with modeling some of NASA KSC's largest structures. Given the size of the welded structures here at KSC, it was critically important to properly organize model struc.ture and carefully manage references. Additionally, because of the amount of hardware to be installed on these structures, it was very important to have a means to coordinate between different design teams and organizations, check for interferences, produce consistent drawings, and allow for simple release processes. Facing these challenges, the modeling team developed a unique reference management methodology and model fidelity methodology. This presentation will describe the techniques and methodologies that were developed for these projects. The attendees will learn about KSC's reference management and model fidelity methodologies for large structures. The attendees will understand the goals of these methodologies. The attendees will appreciate the advantages of developing a reference management methodology.

Jones, Corey↗
NASA NTRS1976

A distribution benefits model for improved information on worldwide crop production. Volume 1: Model structure and application to wheat

The improved model is suitable for the study of benefits of worldwide information on a variety of crops. Application to the previously studied case of worldwide wheat production shows that about $108 million per year of distribution benefits to the United States would be achieved by a satellite-based wheat information system meeting the goals of LACIE. The model also indicates that improved information alone will not change world stock levels unless production itself is stabilized. The United States benefits mentioned above are associated with the reduction of price fluctuations within the year and the more effective use of international trade to balance supply and demand. Price fluctuations from year to year would be reduced only if production variability were itself reduced.

Andrews, J.↗
NASA NTRS2000

A Catchment-Based Approach to Modeling Land Surface Processes in a GCM: Model Structure - Part 1

A new strategy for modeling the land surface component of the climate system is described. The strategy is motivated by an arguable deficiency in most state-of-the-art land surface models (LSMs), namely the disproportionately higher emphasis given to the formulation of one-dimensional, vertical physics relative to the treatment of horizontal heterogeneity in surface properties -- particularly subgrid soil moisture variability and its effects on runoff generation. The new strategy calls for the partitioning of the continental surface into a mosaic of hydrologic catchments, delineated through analysis of high-resolution surface elevation data. The effective "grid" used for the land surface is therefore not specified by the overlying atmospheric grid. Within each catchment, the variability of soil moisture is related to characteristics of the topography and to three bulk soil moisture variables through a well-established model of catchment processes. This modeled variability allows the partitioning of the catchment into several areas representing distinct hydrological regimes, wherein distinct (regime-specific) evaporation and runoff parameterizations are applied. Care is taken to ensure that the deficiencies of the catchment model in regions of little to moderate topography are minimized.

Koster, Randal D.↗
NASA NTRS1988

The solar simulation test of the ITALSAT thermal structural model

The ITALSAT structural/thermal model (STM) was submitted to a solar simulation test in order to verify the spacecraft thermal design and the thermal mathematical model which will be used to predict the on orbit temperatures. The STM was representative of the flight model in terms of configuration, structures, appendages and thermal hardware; dissipating dummy units were used to simulate the electronic units. The test consisted of the main phases: on station (beginning of life), on station (end of life), and transfer orbit. Preliminary results indicate that the test performances were satisfactory. The spacecraft measured temperatures were up to 15 degrees higher than the predicted ones. This imposes a careful correlation analysis in order to have reliable flight temperature predictions.

Giommi, M.↗
NASA NTRS2002

Structural Modeling of a Five-Meter Thin Film Inflatable Antenna/Concentrator

Inflatable structures have been the subject of renewed interest in recent years for space applications such as communications antennas, solar thermal propulsion, and space solar power. A major advantage of using inflatable structures in space is their extremely light weight. An obvious second advantage is on-orbit deployability and related space savings in the launch configuration. A recent technology demonstrator flight for inflatable structures was the Inflatable Antenna Experiment (IAE) that was deployed on orbit from the Shuttle Orbiter. Although difficulty was encountered in the inflation/deployment phase, the flight was successful overall and provided valuable experience in the use of such structures. Several papers on static structural analysis of inflated cylinders have been written, describing different techniques such as linear shell theory, and nonlinear and variational methods, but very little work had been done in dynamics of inflatable structures until recent years. In 1988 Leonard indicated that elastic beam bending modes could be utilized in approximating lower-order frequencies of inflatable beams. Main, et al. wrote a very significant 1995 paper describing results of modal tests of inflated cantilever beams and the determination of effective material properties. Changes in material properties for different pressures were also discussed, and the beam model was used in a more complex structure. The paper demonstrated that conventional finite element analysis packages could be very useful in the analysis of complex inflatable structures. The purposes of this paper are to discuss the methodology for dynamically characterizing a large 5-meter thin film inflatable reflector, and to discuss the test arrangement and results. Nonlinear finite element modal results are compared to modal test data. The work is significant and of considerable interest to researchers because of 1) the large size of the structure, making it useful for scaling studies, and 2) application of commercially available finite element software for modeling pressurized thin-film structures.

Smalley, Kurt B.↗
DOE OSTI2020

BISON High Burnup Structure Modeling Capabilities Validated with a Selection of the Halden IFA-650 Rods

The U.S. Department of Energy (DOE)’s Nuclear Energy Advanced Modeling and Simulation (NEAMS)program aims to develop predictive capabilities using computational methods for the analysis and design of advanced reactor and fuel cycle systems. This program has been supporting the development of BISON, a high-fidelity and high-resolution fuel performance tool at the engineering scale. This document continues analysis and refinement of capabilities added to BISON early this calendar year in regards to the incorporation of capabilities applicable to extended burnups in response to industry interest. Details are provided on high burnup thermal conductivity models, a refitting of the high-burnup structure (HBS) porosity formation model to include additional data, the coupling of the HBS volume fraction model to thermal conductivity and fine fragmentation models, and validation activities. The IFA-650.4 and IFA-650.9 loss of coolant accident (LOCA) analyses are revisited with the latest developments in this report. A new validation case, IFA-650.14 has also been added to the BISON test suite.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1994

Dynamic-stall and structural-modeling effects on helicopter blade stability with experimental correlation

The effects of blade and root-flexure elasticity and dynamic stall on the stability of hingeless rotor blades are investigated. The dynamic stall description is based on the ONERA models of lift, drag, and pitching moment. The structural analysis is based on three blade models that range from a rigid flap-lag model to two elastic flap-lag-torsion models, which differ in representing root-flexure elasticity. The predictions are correlated with the measured lag damping of an experimental isolated three-blade rotor; the correlation covers rotor operations from near-zero-thrust conditions in hover to highly stalled, high-thrust conditions in foward flight. That correlation shows sensitivity of lag-damping predictions to structural refinements in blade and root-flexure modeling. Moreover, this sensitivity increases with increasing control pitch angle and advance ratio. For high-advance-ratio and high-thrust conditions, inclusion of dynamic stall generally improves the correlation.

Barwey, D.↗
NASA NTRS1988

The GISS global climate-middle atmosphere model. I - Model structure and climatology

A coupled global climate/middle atmosphere model (GCMAM) is developed by extending the Hansen et al. (1983) GISS global climate model to include the middle atmosphere up to 85 km. The model includes numerical solutions of the primitive equations, calculations of the radiative and surface fluxes, and a complete hydrologic cycle with convective and cloud-cover parameterizations. In addition, a parameterized gravity wave drag cycle is incorporated, in which gravity-wave momentum fluxes due to flow over topography, wind shear, and convection are calculated at each grid box, using theoretical relationships between the grid-scale variables and expected source strengths. The results of the GCMAM demonstrate that the model produces a reasonable simulation of the stratosphere. It is shown that the improvements over the previous version were achieved largely through the incorporation of the parameterized gravity wave drag.

Rind, D.↗
NASA NTRS2008

Structural Model Tuning Capability in an Object-Oriented Multidisciplinary Design, Analysis, and Optimization Tool

Updating the finite element model using measured data is a challenging problem in the area of structural dynamics. The model updating process requires not only satisfactory correlations between analytical and experimental results, but also the retention of dynamic properties of structures. Accurate rigid body dynamics are important for flight control system design and aeroelastic trim analysis. Minimizing the difference between analytical and experimental results is a type of optimization problem. In this research, a multidisciplinary design, analysis, and optimization [MDAO] tool is introduced to optimize the objective function and constraints such that the mass properties, the natural frequencies, and the mode shapes are matched to the target data as well as the mass matrix being orthogonalized.

Lung, Shun-fat↗
NASA NTRS2008

Structural Model Tuning Capability in an Object-Oriented Multidisciplinary Design, Analysis, and Optimization Tool

Updating the finite element model using measured data is a challenging problem in the area of structural dynamics. The model updating process requires not only satisfactory correlations between analytical and experimental results, but also the retention of dynamic properties of structures. Accurate rigid body dynamics are important for flight control system design and aeroelastic trim analysis. Minimizing the difference between analytical and experimental results is a type of optimization problem. In this research, a multidisciplinary design, analysis, and optimization (MDAO) tool is introduced to optimize the objective function and constraints such that the mass properties, the natural frequencies, and the mode shapes are matched to the target data as well as the mass matrix being orthogonalized.

Lung, Shun-fat↗
NASA NTRS2007

Aeroelastic Model Structure Computation for Envelope Expansion

Structure detection is a procedure for selecting a subset of candidate terms, from a full model description, that best describes the observed output. This is a necessary procedure to compute an efficient system description which may afford greater insight into the functionality of the system or a simpler controller design. Structure computation as a tool for black-box modelling may be of critical importance in the development of robust, parsimonious models for the flight-test community. Moreover, this approach may lead to efficient strategies for rapid envelope expansion which may save significant development time and costs. In this study, a least absolute shrinkage and selection operator (LASSO) technique is investigated for computing efficient model descriptions of nonlinear aeroelastic systems. The LASSO minimises the residual sum of squares by the addition of an l(sub 1) penalty term on the parameter vector of the traditional 2 minimisation problem. Its use for structure detection is a natural extension of this constrained minimisation approach to pseudolinear regression problems which produces some model parameters that are exactly zero and, therefore, yields a parsimonious system description. Applicability of this technique for model structure computation for the F/A-18 Active Aeroelastic Wing using flight test data is shown for several flight conditions (Mach numbers) by identifying a parsimonious system description with a high percent fit for cross-validated data.

Kukreja, Sunil L.↗
NASA NTRS2007

Aeroelastic Model Structure Computation for Envelope Expansion

Structure detection is a procedure for selecting a subset of candidate terms, from a full model description, that best describes the observed output. This is a necessary procedure to compute an efficient system description which may afford greater insight into the functionality of the system or a simpler controller design. Structure computation as a tool for black-box modeling may be of critical importance in the development of robust, parsimonious models for the flight-test community. Moreover, this approach may lead to efficient strategies for rapid envelope expansion that may save significant development time and costs. In this study, a least absolute shrinkage and selection operator (LASSO) technique is investigated for computing efficient model descriptions of non-linear aeroelastic systems. The LASSO minimises the residual sum of squares with the addition of an l(Sub 1) penalty term on the parameter vector of the traditional l(sub 2) minimisation problem. Its use for structure detection is a natural extension of this constrained minimisation approach to pseudo-linear regression problems which produces some model parameters that are exactly zero and, therefore, yields a parsimonious system description. Applicability of this technique for model structure computation for the F/A-18 (McDonnell Douglas, now The Boeing Company, Chicago, Illinois) Active Aeroelastic Wing project using flight test data is shown for several flight conditions (Mach numbers) by identifying a parsimonious system description with a high percent fit for cross-validated data.

Kukreja, Sunil L.↗