Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface property”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Atomic-Level Understanding of Surface Reconstruction Based on Li[Ni x Mn y Co 1–x–y ]O 2 Single-Crystal Studies

The stability of cathode particle surfaces that are directly exposed to the electrolyte is one of the most crucial and determining factors for cathode performance at high operating voltages. Theory has predicted a strong dependence of surface stability on chemical compositions as well as surface facets of layered oxides, yet conflicting results on the correlations exist as most experimental studies focus on cycled secondary particles recovered from composite electrodes. Here, we synthesize well-formed Li[Ni x Mn y Co 1–x–y ]O 2 (NMC) single-crystal samples, carefully define pristine surface properties, and then monitor their evolution with cycling. Atomic-resolution scanning transmission electron microscopy (STEM) imaging and electron energy loss spectroscopy (EELS) analysis show the formation of a surface reconstruction layer (SRL) as well as an extended surface reduction layer on pristine, Li-permeable non-(001) surfaces, even before cycling. We reveal a transition region with chemical gradient, in which the layered structure gradually densifies and eventually transforms into the SRL on the top surface. Contrary to these observations, no SRL is observed on pristine, Li-impermeable (001) surfaces, revealing the facet-dependent nature of surface reconstructions during particle synthesis. Upon electrochemical cycling, significant composition-and facet-dependent SRL growth is observed. The driving force and mechanism for surface reconstruction are further discussed. The present study provides insights into the origin as well as the nature of SRLs, highlighting the significance of surface engineering in cathode material optimization.

25 ENERGY STORAGE↗
DOE OSTI2023

Exploring Mission Design for Imaging Spectroscopy Retrievals for Land and Aquatic Ecosystems

The retrieval algorithms used for optical remote sensing satellite data to estimate Earth's geophysical properties have specific requirements for spatial resolution, temporal revisit, spectral range and resolution, and instrument signal-to-noise ratio (SNR) performance to meet biogeoscience objectives. Studies to estimate surface properties from hyperspectral data use a range of algorithms sensitive to various sources of spectroscopic uncertainty, which are in turn influenced by mission architecture choices. Retrieval algorithms vary across scientific fields and may be more or less sensitive to mission architecture choices that affect spectral, spatial, or temporal resolutions and spectrometer SNR. We used representative remote sensing algorithms across terrestrial and aquatic study domains to inform aspects of mission design that are most important for impacting accuracy in each scientific area. We simulated the propagation of uncertainties in the retrieval process including the effects of different instrument configuration choices. We found that retrieval accuracy and information content degrade consistently at >10 nm spectral resolution, >30 m spatial resolution, and >8-day revisit. In these studies, the noise reduction associated with lower spatial resolution improved accuracy vis à vis high spatial resolution measurements. The interplay between spatial resolution, temporal revisit, and SNR can be quantitatively assessed for imaging spectroscopy missions and used to identify key components of algorithm performance and mission observing criteria.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Characterization of Surface Heterogeneity-Induced Convection Using Cluster Analysis

Land-atmosphere interactions and boundary layer processes often control the formation of shallow clouds and subsequently deep convective precipitation over the Southern Great Plains. In this study, we examine the impacts of large-scale advection on the cloud populations and land-atmospheric coupling observed during the Holistic Interactions of Shallow Clouds, Aerosols, and Land-Ecosystems (HI-SCALE) field campaign in 2016. In this work, we performed two Large Eddy Simulations (LES) using the Weather Research and Forecasting Model for a day in which the transition from clear-sky to shallow precipitating clouds and isolated deep convection was observed. The control simulation reproduced the overall distribution of cloud populations by using realistic soil conditions with an interactive land model. In the sensitivity simulation where large-scale advection is removed, a strong relationship between the land and boundary layer is found. To study the timing, location, and intensity of convective initiation and the relationship of clouds with land surface properties, a cluster analysis of equivalent potential temperature is performed for the simulation without large-scale advection. That analysis shows that convective clouds first form over regions with higher surface sensible heat flux. Precipitation from those convective clouds likely triggers new updrafts nearby about two hours later through the lifting associated with cold pools. Furthermore, the cluster analysis also shows that in addition to the spatial pattern of soil moisture, land use and soil texture in western Oklahoma also influence the location of convective initiation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Competing electronic states emerging on polar surfaces

Excess charge on polar surfaces of ionic compounds is commonly described by the two-dimensional electron gas (2DEG) model, a homogeneous distribution of charge, spatially-confined in a few atomic layers. Here, by combining scanning probe microscopy with density functional theory calculations, we show that excess charge on the polar TaO 2 termination of KTaO 3 (001) forms more complex electronic states with different degrees of spatial and electronic localization: charge density waves (CDW) coexist with strongly-localized electron polarons and bipolarons. These surface electronic reconstructions, originating from the combined action of electron-lattice interaction and electronic correlation, are energetically more favorable than the 2DEG solution. They exhibit distinct spectroscopy signals and impact on the surface properties, as manifested by a local suppression of ferroelectric distortions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Vapor-phase grafting of functional silanes on atomic layer deposited Al 2 O 3

Fundamental studies are needed to advance our understanding of selective adsorption in aqueous environments and develop more effective sorbents and filters for water treatment. Vapor-phase grafting of functional silanes is an effective method to prepare well-defined surfaces to study selective adsorption. In this investigation, we perform vapor phase grafting of five different silane compounds on aluminum oxide (Al2O3) surfaces prepared by atomic layer deposition. These silane compounds have the general formula L3Si–C3H6–X where the ligand, L, controls the reactivity with the hydroxylated Al2O3 surface and the functional moiety, X, dictates the surface properties of the grafted layer. We study the grafting process using in situ Fourier transform infrared spectroscopy and ex situ x-ray photoelectron spectroscopy measurements, and we characterize the surfaces using scanning electron microscopy, atomic force microscopy, and water contact angle measurements. Here, we found that the structure and density of grafted aminosilanes are influenced by their chemical reactivity and steric constraints around the silicon atom as well as by the nature of the anchoring functional groups. Methyl substituted aminosilanes yielded more hydrophobic surfaces with a higher surface density at higher grafting temperatures. Thiol and nitrile terminated silanes were also studied and compared to the aminosilane terminated surfaces. Uniform monolayer coatings were observed for ethoxy-based silanes, but chlorosilanes exhibited nonuniform coatings as verified by atomic force microscopy measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Analysis of the Surface Morphology and Chemical Composition of Zr-Nb3Sn Alloys with Zr Different Concentrations

The Zr inclusion in Nb3Sn can improve the high magnetic field performance of Nb3Sn radio frequency cavities. The focus of this project is to characterize the surface properties and chemical composition of Zr-Nb3Sn. Nb3Sn was doped with two different concentrations of Zr. ~0.5%, and ~24% Zr. Various spectroscopy techniques were used to examine how the surface morphology and chemical composition changes with increasing Zr fraction in Nb3Sn.

Sue, Micah↗
DOE OSTI2022

In-situ exsolution of bimetallic CoFe nanoparticles on (La,Sr)FeO 3 perovskite: Its effect on electrocatalytic oxidative coupling of methane

This study presents in-situ reduction of lanthanum strontium cobalt ferrite (LSCF) perovskite as an effective method for modifying its surface properties and enhancing its electrocatalytic reactivity for oxidative coupling of methane (OCM). The evolution of hetero-phases during the reduction of LSCF resulted in CoFe nanoparticles being formed at the surface. The in-situ reduced LSCF cell for OCM could be operated in either an ion pump or a fuel cell mode. High selectivity of 63% and 10.2% were reported for C 2+ hydrocarbons and C 3 H 6 , respectively. DFT calculations on LSCF and CoFe revealed that the high selectivity of C 2+ hydrocarbons on the LSCF primarily stems from the presence of CoFe nanoparticles. In-situ DRIFTS conducted under CH 4 proved that complete oxidation of CH 4 can be effectively inhibited by reducing LSCF, and control of oxygen supply is an important parameter for selective conversion of CH 4 to higher order hydrocarbon.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Analysis of the Surface Morphology and Chemical Composition of Zr-Nb3Sn Alloys with Zr Different Concentrations

The inclusion of zirconium (Zr) in niobium-tin (Nb3Sn) significantly enhances the performance of Nb3Sn radiofrequency cavities in high magnetic fields. This research project is dedicated to characterizing the surface properties and chemical composition of Zr-doped Nb3Sn. Two different concentrations of Zr were used for doping: approximately 0.5% and 24%. Various spectroscopy techniques were employed to analyze how the surface morphology and chemical composition of Nb3Sn change with increasing Zr content. The findings of this study indicate that the grain size decreases as the Zr concentration increases. In samples with 24% Zr, nanometer-sized particles, likely oxides, were observed. X-ray photoelectron spectroscopy (XPS) data revealed that the thickness of niobium oxides (NbOx) decreases with increasing Zr, while the thickness of tin oxides (SnOx) increases. Additionally, grain size distribution analysis showed that the average grain size is around 5300 nm , with a grain area density of about 165 grains/μm .

Sue, Micah↗
DOE OSTI2021

In situ spectroscopic insights into the redox and acid-base properties of ceria catalysts

Cerium oxide (ceria) plays an important and fascinating role in heterogeneous catalysis as illustrated by its versatile use as a catalyst, a catalyst support, or a promotor in various oxidation and reduction reactions. Central to these reactions is the rich defect chemistry, facile redox capability, and unusual acid-base properties of ceria. Understanding the unique redox and acid-base properties of ceria is essential to build the structure-catalysis relationship so that improved catalytic functions can be achieved for ceria-based materials. Among the characterization toolbox, spectroscopic approach indisputably stands out for its unparalleled power in offering chemical insights into the surface properties of ceria at atomic and molecular level. In this review, we summarize advances in revealing the redox and acid-base properties of ceria via a variety of spectroscopic methods including optical, X-ray, neutron, electronic and nuclear spectroscopy. Both direct spectroscopy characterization and its coupling with probe molecules are analyzed to illustrate how the nature, strength and density of different surface sites are influenced by the pretreatment, the morphology and size of ceria nanoparticles. Further directions in taking advantage of in situ/operando spectroscopy for better understanding the catalysis of ceria-based materials are detailed in the summary and outlook section.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Picosecond Carrier Dynamics in InAs and GaAs Revealed by Ultrafast Electron Microscopy

Understanding the limits of spatio-temporal carrier dynamics, especially in III-V semiconductors, is key to designing ultrafast and ultra-small optoelectronic components. However, identifying such limits and the properties controlling them has been elusive. Here, using scanning ultrafast electron microscopy (SUEM), in bulk n-GaAs and p-InAs, we simultaneously measure picosecond carrier dynamics along with three related quantities: sub-surface band bending, above-surface vacuum potentials, and surface trap densities. We make two surprising observations. First, we uncover a negative-time contrast in secondary electrons resulting from an interplay among these quantities. Second, despite dopant concentrations and surface state densities differing by many orders of magnitude between the two materials, their carrier dynamics, measured by photo-excited band bending and filling of surface states, occur at a seemingly common timescale of about 100 ps. This observation may indicate fundamental kinetic limits tied to a multitude of material and surface properties of optoelectronic III-V semiconductors, and highlights the need for techniques that simultaneously measure electro-optical kinetic properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Influence of Annealing Temperature on the OER Activity of NiO(111) Nanosheets Prepared via Microwave and Solvothermal Synthesis Approaches

Earth-abundant transition metal oxides are promising alternatives to precious metal oxides as electrocatalysts for the oxygen evolution reaction (OER) and are intensively investigated for alkaline water electrolysis. OER electrocatalysis, like most other catalytic reactions, is surface-initiated, and the catalyst performance is fundamentally determined by the surface properties. Most transition metal oxide catalysts show OER activities that depend on the predominantly exposed crystal facets/surface structure. Therefore, the design of synthetic strategies to obtain the most active crystal facets is of significant research interest. In this work, rock salt NiO OER catalysts with (111) predominantly exposed facets were synthesized by a solvothermal (ST) method either heated under supercritical or microwave-assisted (MW) conditions. Particular emphasis was placed on the influence of the post annealing temperature on the structural configuration and OER activity to compare their catalytic performances. The as-prepared electrocatalysts are pure α-Ni hydroxides which were converted to rock salt NiO (111) nanosheets with hexagonal pores after heat treatment at different temperatures. The OER activity of the electrodes has been evaluated in 0.1 M KOH using geometric and intrinsic current densities via normalization by the disk area and BET area, respectively. The lowest overpotential at a geometric current density of 10 mA/cm 2 is found for samples pretreated by heating between 400 and 500 °C with a catalyst loading of 115 μg/cm 2 . Despite the very similar nature of the catalysts obtained from the two methods, the ST electrodes show a higher geometric and intrinsic current density for 500 °C pretreatment. The MW electrodes, however, achieve an optimal geometric current density for 400 °C pretreatment, while their intrinsic current density requires pretreatment over 600 °C. Interestingly, pretreated electrodes show consistently higher OER activity as compared to the poorly crystalline/less ordered hydroxide as-prepared electrocatalysts. Thus, our study highlights the importance of the synthesis method and pretreatment at an optimal temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Penetration of foliar-applied Zn and its impact on apple plant nutrition status: in vivo evaluation by synchrotron-based X-ray fluorescence microscopy

The absorption of foliar fertilizer is a complex process and is poorly understood. The ability to visualize and quantify the pathway that elements take following their application to leaf surfaces is critical for understanding the science and for practical applications of foliar fertilizers. By the use of synchrotron-based X-ray fluorescence to analyze the in vivo localization of elements, our study aimed to investigate the penetration of foliar-applied Zn absorbed by apple leaves with different physiological surface properties, as well as the possible interactions between foliar Zn level and the mineral nutrient status of treated leaves. The results indicate that the absorption of foliar-applied Zn was largely dependent on plant leaf surface characteristics. High-resolution elemental maps revealed that the high binding capacity of the cell wall for Zn contributed to the observed limitation of Zn penetration across epidermal cells. Trichome density and stomatal aperture had opposite effects on Zn fertilizer penetration: a relatively high density of trichomes increased the hydrophobicity of leaves, whereas the presence of stomata facilitated foliar Zn penetration. Low levels of Zn promoted the accumulation of other mineral elements in treated leaves, and the complexation of Zn with phytic acid potentially occurred owing to exposure to high-Zn conditions. The present study provides direct visual evidence for the Zn penetration process across the leaf surface, which is important for the development of strategies for Zn biofortification in crop species.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Carbon Electrodes from Powder River Basin Coal Development of Competitive Supercapacitor Electrodes of Diverse Compositions from Coal Extract

Recent demand for coal as a thermal energy source has decreased significantly and will likely continue to decrease as renewable sources of energy become more available and environmental concern and cost from burning coal makes it more costly than renewables. Given that Powder River Basin (PRB) coal in Wyoming has relatively low thermal energy, it is critical for Wyoming to employ coal in other capacities at the current energy transition period in history. Among many potential non-thermal applications, PRB coal can be utilized for membrane and electrode applications through the formation of carbon fibers. Coal-derived membranes can become low-cost, conductive membranes for use in electrodialysis separation processes. Carbon fiber derived electrodes have been shown be a cost-effective alternative to typical electrode materials that can meet or exceed the performance of current carbon electrode materials. In this talk, we demonstrate the manufacture of supercapacitor electrodes from Powder River Basin (PRB) coal-derived precursors. Specifically, PRB coal was treated in cheap solvents, partitioned into liquid extract and solid residue. An electropinning process has been developed that can convert either the liquid extract or the solid residue into carbon fiber mats. The electrospinning process is versatile with many tunable process parameters to achieve desirable physiochemical properties. For example, the coal residue can be manipulated by additional heat treatment, or by adding binders, salts, or surfactants to create a solution that can be electrospun into advanced carbon electrodes with desirable structural and surface properties. Similarly, some of the liquid extract (tar fraction) can be subsequently reacted with toluene diisocyanate to create resinous coal-derived polyurethane (PUs) as a spinnable ink. Carbon nanofiber mats made from our proprietary electrospinning process were further carbonized at temperature ranging from 700°C to 900°C before they are used as electrodes in supercapacitors. Galvanostatic charge-discharge (GCD) results show that the best performing PU fiber mats can deliver a specific capacitance of 604 F g -1 at the current density of 1 A g -1 . A carbon fiber mat from a different solvent extraction residue also delivered the specific capacitance of 508 F g -1 . These specific capacitance values are comparable to or better than commercial activated carbons, demonstrating the viability of manufacturing carbon nanofiber electrodes from coal without the use of a commercial polymer as binder in the spinning ink.

Cincotta, Robert↗
DOE OSTI2024

Picosecond carrier dynamics in InAs and GaAs revealed by ultrafast electron microscopy

Understanding the limits of spatiotemporal carrier dynamics, especially in III-V semiconductors, is key to designing ultrafast and ultrasmall optoelectronic components. However, identifying such limits and the properties controlling them has been elusive. Here, using scanning ultrafast electron microscopy, in bulk n-GaAs and p-InAs, we simultaneously measure picosecond carrier dynamics along with three related quantities: subsurface band bending, above-surface vacuum potentials, and surface trap densities. We make two unexpected observations. First, we uncover a negative-time contrast in secondary electrons resulting from an interplay among these quantities. Second, despite dopant concentrations and surface state densities differing by many orders of magnitude between the two materials, their carrier dynamics, measured by photoexcited band bending and filling of surface states, occur at a seemingly common timescale of about 100 ps. This observation may indicate fundamental kinetic limits tied to a multitude of material and surface properties of optoelectronic III-V semiconductors and highlights the need for techniques that simultaneously measure electro-optical kinetic properties.

42 ENGINEERING↗
DOE OSTI2020

Current measurements in the intermittent-contact mode of atomic force microscopy using the Fourier method: a feasibility analysis

Atomic force microscopy (AFM) is an important tool for measuring a variety of nanoscale surface properties, such as topography, viscoelasticity, electrical potential and conductivity. Some of these properties are measured using contact methods (static contact or intermittent contact), while others are measured using noncontact methods. Some properties can be measured using different approaches. Conductivity, in particular, is mapped using the contact-mode method. However, this modality can be destructive to delicate samples, since it involves continuously dragging the cantilever tip on the surface during the raster scan, while a constant tip–sample force is applied. In this paper we discuss a possible approach to develop an intermittent-contact conductive AFM mode based on Fourier analysis, whereby the measured current response consists of higher harmonics of the cantilever oscillation frequency. Such an approach may enable the characterization of soft samples with less damage than contact-mode imaging. To explore its feasibility, we derive the analytical form of the tip–sample current that would be obtained for attractive (noncontact) and repulsive (intermittent-contact) dynamic AFM characterization, and compare it with results obtained from numerical simulations. Although significant instrumentation challenges are anticipated, the modelling results are promising and suggest that Fourier-based higher-harmonics current measurement may enable the development of a reliable intermittent-contact conductive AFM method.

14 SOLAR ENERGY↗
DOE OSTI2025

Silylsilane‐Substituted Polymers: Fluorine‐Free, Liquid Repellent, and Hydrolytically Stable Alternatives to Siloxanes

Abstract Per‐ and polyfluoroalkyl substances (PFAS) are omniphobic and exceptionally stable, making them ideal for a wide range of materials applications. However, as “forever chemicals”, their exceptional persistence and bioaccumulation have generated an increasing amount of environmental and health concerns, prompting the search for fluorine‐free alternatives. Siloxane‐based materials are therefore interesting to examine as PFAS alternatives due to their low surface energy and hydrophobicity but suffer from hydrolytic instability of Si─O linkages. To address this challenge, a novel methacrylate monomer, 3‐[tris(trimethylsilyl)silyl]propyl methacrylate (M‐silyl), is designed containing Si─Si bonds rather than Si─O bonds of siloxanes. Polymers derived from M‐silyl (P‐silyl) is prepared by controlled free radical polymerization and compared with their siloxane analogues after coating on silicon wafers. Contact angle (CA) measurements confirmed P‐silyl to be hydrophobic (advancing/receding water CA = 109.7°/83.0°), with a low‐hysteresis for oil (lyophobic) (hexadecane CA hysteresis = 2.0°), comparable to its siloxane‐based counterpart. Importantly, P‐silyl maintained these surface properties after exposure to acidic or basic conditions, while siloxane analogues lost hydrophobicity. Consequently, the incorporation of Si ─ Si linkages into the design of the polymer enables chemically stable, fluorine‐free alternatives for water‐repellent and low hysteresis surface coatings and advances the design of fluorine‐free functional materials.

fluorine-free↗
DOE OSTI2026

Illinois Storage Corridor - CarbonSAFE Phase III: Policy, Regulatory, Legal and Permitting Characteristics; Subtask 5.5

The Illinois Storage Corridor (ISC) project aims to advance the commercial development and implementation of carbon capture and storage (CCS) technologies within a region in Illinois of suitable geology for carbon dioxide (CO 2 ) storage in deep saline aquifers. The project partners have annual emissions greater than 6.5 million tonnes per year; storage hubs are being explored at two sites—one near the One Earth Energy facility in east-central Illinois, and one near the Prairie State Generating Company campus in southwest Illinois. To implement the technology, legal, policy, and economic considerations must be explored. The United States Environmental Protection Agency (US EPA) administers the Underground Injection Control (UIC) program and is responsible for issuing Class VI permits to construct and operate CO 2 injection wells, i.e., a UIC Class VI well permit is required to inject CO 2 into the subsurface for geologic sequestration. The largest consideration of the Class VI well requirements is to protect underground sources of drinking water (USDWs). Additionally discussed are considerations for Class VI permits relating to public engagement. Besides permitting, property rights to storage sites, subsurface pore spaces, and areas for pipeline transportation must be secured. Pore space rights is still a novel concept being explored and not yet addressed by the Illinois legislature. It is believed that surface property rights are required for the subsurface pore space below, so long as there is not a separated mineral estate in the subsurface. Illinois legislature has addressed securing rights-of-way for CO 2 transportation, allowing for easements and the exercise of eminent domain to secure such rights. Economically, the incentives for CCS are ever-expanding. Recently, the federal government broadened the availability and increased the dollar-amounts for the § 45Q tax credits for geological storage of carbon oxides. Congress has also authorized the Advanced Industrial Facilities Development Program which allocates billions of dollars in funds to installing technology at industrial facilities to reduce greenhouse gas emissions. On the state level, Illinois has had its own incentives for CCS projects since 2009 and expanded its emission-related goals again in 2021. The law enacted in 2021 specifically creates a commission to explore implementing CCS at Prairie State Generating Company, a partner on the Illinois Storage Corridor project.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Optical properties of semiconductor nanoparticles doped with 3d and 4f block elements

Doped inorganic nanoparticles (NPs) have enabled researchers across multiple disciplines to create new materials with unique optical, electronic, magnetic, electrical, chemical, and/or compositional properties. In the quest for generating newer functional materials with controlled optical and electronic properties, the use of d- and f-block elements as dopants in the inorganic NPs remain at the forefront of research. This article summarizes experiments that identify the important control parameters, in the form of NP core and surface properties, for promoting host-sensitized dopant emission from d- and f-doped inorganic/semiconductor NPs. We conclude that energy offsets between the dopant and NP electronic levels and an understanding of the charge trapping mechanisms can be used to predict dopant luminescence, and we claim that these features can be used to choose NP host materials by design, rather than by trial and error.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗