Search NASA⌕ Search

SEARCH · Search NASA

Results for “TAIL MOUNTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1944

Experimental Verification of the Rudder-Free Stability Theory for an Airplane Model Equipped with Rudders Having Negative Floating Tendency and Negligible Friction

An investigation has been made in the Langley free-flight tunnel to obtain an experimental verification of the theoretical rudder-free stability characteristics of an airplane model equipped with conventional rudders having negative floating tendencies and negligible friction. The model used in the tests was equipped with a conventional single vertical tail having rudder area 40 percent of the vertical tail area. The model was tested both in free flight and mounted on a strut that allowed freedom only in yaw. Tests were made with three different amounts of rudder aerodynamic balance and with various values of mass, moment of inertia, and center-of-gravity location of the rudder. Most of the stability derivatives required for the theoretical calculations were determined from forced and free-oscillation tests of the particular model tested. The theoretical analysis showed that the rudder-free motions of an airplane consist largely of two oscillatory modes - a long-period oscillation somewhat similar to the normal rudder-fixed oscillation and a short-period oscillation introduced only when the rudder is set free. It was found possible in the tests to create lateral instability of the rudder-free short-period mode by large values of rudder mass parameters even though the rudder-fixed condition was highly stable. The results of the tests and calculation indicated that for most present-day airplanes having rudders of negative floating tendency, the rudder-free stability characteristics may be examined by simply considering the dynamic lateral stability using the value of the directional-stability parameter Cn(sub p) for the rudder-free condition in the conventional controls-fixed lateral-stability equations. For very large airplanes having relatively high values of the rudder mass parameters with respect to the rudder aerodynamic parameters, however, analysis of the rudder-free stability should be made with the complete equations of motion. Good agreement between calculated and measured rudder-free stability characteristics was obtained by use of the general rudder-free stability theory, in which four degrees of lateral freedom are considered. When this assumption is made that the rolling motions alone or the lateral and rolling motions may be neglected in the calculations of rudder-free stability, it is possible to predict satisfactorily the characteristics of the long-period (Dutch roll type) rudder-free oscillation for airplanes only when the effective-dihedral angle is small. With these simplifying assumptions, however, satisfactory prediction of the short-period oscillation may be obtained for any dihedral. Further simplification of the theory based on the assumption that the rudder moment of inertia might be disregarded was found to be invalid because this assumption made it impossible to calculate the characteristics of the short-period oscillations.

STABILITY- FAIRCHILD R2K-1↗
NASA NTRS1974

Investigation of space shuttle orbiter subsonic stability and control characteristics in the NAAL low speed wind tunnel (0A62b), volume 1

Experimental aerodynamic investigations were conducted on a sting-mounted 0.0405 scale representation of the 140A/B space shuttle orbiter in a 7.75 ft by 11 ft low speed wind tunnel during the time period from November 14, 1973, to December 6, 1973, with the primary test objectives being to establish basic longitudinal stability characteristics in and out of ground effect, as well as lateral-directional stability characteristics in free air. Two dual podded nacelle configurations were also tested, one with three dual podded nacelles on the lower wing surface, and the other with a single dual nacelle on the lower centerline with dual nacelle pylons mounted above each wing. Stability and control characteristics were investigated at nominal elevon, rudder, aileron, and body flap deflections. Pressure bugs were used to determine pressures on the vertical tail at spanwise stations, and aerodynamic force and moment data were measured in the stability axis system by an internally mounted, six component strain gage balance.

Mennell, R.↗
NASA NTRS1986

An evaluation of leading-edge flap performance on delta and double-delta wings at supersonic speeds

The aerodynamic performance of leading-edge flaps on three delta double-delta wing planforms having aspect ratios of 1.75, 2.11, and 2.50, have been investigated experimentally. The wings were mounted on a generic fuselage without an inlet canopy, or a vertical tail. The Mach numbers of the flow over the wings were 1.60, 1.90 and 2.16. A primary set of full-span leading-edge flaps with similar root and tip chords were tested on each wing, and several alternate flap planforms were tested on the aspect ratio 1.75 wings. It is found that all leading edge geometries were effective in reducing drag lifting over the range of wing aspect ratios and Mach numbers tested. Greater flap performance was obtained when primary flaps were applied to the delta planform. In general, the primary flap geometry yielded better performance than the alternative geometries tested. Flow visualization techniques were found to be useful for identifying the beneficial effects of leading-edge flap deflection on flow separation as well as fuselage interference effects. Black and white photographs of the delta and double-delta planforms are provided.

Covell, P. F.↗
NASA NTRS1987

Supersonic Aerodynamic Characteristics of a Space Shuttle Orbiter Model at Angles of Attack from 20 Deg to 90 Deg

Space Shuttle Orbiter aerodynamic characteristics have been determined in the angle-of-attack range from 20 to 90 degrees and Mach numbers from 4.60 to 1.80 at Reynolds numbers, based on body length, of 2.15 x 10 to the 6th and 4.30 x 10 to the 6th power. Emphasis is on vehicle stability, control, and trim characteristics above a 60 degree angle of attack. The model used was a 0.986 percent scale Orbiter, having a blade-mounted support system entering the model in the region of the vertical tail. Elevon deflections of 0, -10, -20, and -40 degrees and body-flap deflections of 0, +6 and -12 degrees were investigated individually and in combination. Schlieren photographs are also presented for selected configurations and Mach numbers. The Orbiter was found to be longitudinally stable and trimmable in the angle-of-attack range from approximately 60 to 80 degrees. Both the elevon and body flap provided positive pitch control-effectiveness at angles of attack from 60 to 80 degrees and the Mach numbers of this study. For the range of neutral to stable trim in the angle-of-attack range above about 55 degrees, the deflected elevon/body-flap combination provided positive trimmed lift and lift/drag ratios.

Spencer, Bernard, Jr.↗
NASA NTRS1993

Weasel works SA-150: Design study of a 100 to 150 passenger transport aircraft

As the year 2000 rapidly approaches, the airlines are faced with an extremely competitive and environmentally restrictive marketplace. In order to survive, commercial air carriers will need to find new ways to lower their direct operating costs, increase load factors and comply with tightening federal and international constraints. The SA-150 has been designed to meet these demands by focusing on the areas of aerodynamic efficiency, an improved level of passenger comfort, and a limited application of advanced technology. The SA-150 has been optimized for a 500 nmi. mission to help the airlines meet the challenges of the short haul, quick turnaround flight. With a maximum capacity of 124 passengers, and full baggage, the SA-150 is also capable of covering a range of 1500 nmi. This additional range capability will provide the airlines with flexibility when scheduling their routes. The aircraft features a 'V' tail, fly-by-wire system and is powered by two turbofans mounted under a twelve aspect ratio wing. The SA-150 will have an initial production run of 800 units and have a purchase price of $37.7 million in 1993 dollars.

Alkema, Kevin↗
NASA NTRSDate not supplied

Subsonic Single Aft Engine (SUSAN) Transport Aircraft Concept and Trade Space Exploration

A trade space exploration of a new NASA regional transport aircraft concept called the SUbsonic Single Aft eNgine (SUSAN) Electrofan is presented. The SUSAN concept uses a 20MW Electrified Aircraft Propulsion (EAP) system to enable advance Propulsion Airframe Integration (PAI) in transport category aircraft. Alternative fuels will be used to reduce the amount of emissions per energy used. By combining these features there is the potential to reduce aircraft emissions by 50% per passenger/mile while retaining the size, speed, and range of large regional jets. SUSAN is has a 750 mile economic mission, a 2500 mile design range and a maximum capacity of 180 passengers. The SUSAN configuration utilizes a single aft mounted engine and distributed electric wing-mounted thrusters on a tube and wing arrangement with a T-tail empennage. The SUSAN Electrofan employs a hybrid powertrain to enable: single turbofan operation on a large transport category aircraft; increased aerodynamic and propulsive efficiency through placement of electric engines; optimized turbofan sizing and efficiency through control and electric boosting, reduced control surface sizing through thrust augmentation. A single use battery is employed as the power source in case of turbofan failure. The design study also considers the constraints of operating within the current airport, airspace and economic constraints. This paper presents the status of the trade space exploration; however the concept definition is not finished. Forward work includes optimizing the overall aircraft configuration and including certain hard to model features like boundary layer ingestion or natural laminar flow across all appliable subsystems. Additional work forward work is a more extensive analysis of the configuration using alternative fuels.

Ralph H. Jansen↗
NASA NTRSDate not supplied

Brief Overview of Subsonic Single Aft Engine (SUSAN) Transport Aircraft Concept and Trade Space Exploration

The SUSAN concept uses a 20-megawatt Electrified Aircraft Propulsion system to enable advance Propulsion Airframe Integration in transport category aircraft. Alternative fuels will be used to reduce the amount of emissions per energy used. By combining these features there is the potential to reduce aircraft emissions by 50 percent per passenger/mile while retaining the size, speed, and range of large regional jets. The SUSAN is has a 750-mile economic mission, a 2500-mile design range and a maximum capacity of 180 passengers. The SUSAN configuration utilizes a single aft mounted engine and distributed electric wing-mounted thrusters on a tube and wing arrangement with a T-tail empennage. The SUSAN Electrofan employs a hybrid powertrain to enable: single turbofan operation on a large transport category aircraft; increased aerodynamic and propulsive efficiency through placement of electric engines; optimized turbofan sizing and efficiency through control and electric boosting, reduced control surface sizing through thrust augmentation. A single use battery is employed as the power source in case of turbofan failure. The design study also considers the constraints of operating within the current airport, airspace, and economic constraints. Forward work includes optimizing the overall aircraft configuration and including certain hard to model features like boundary layer ingestion or natural laminar flow across all appliable subsystems. Additional work forward work is a more extensive analysis of the configuration using alternative fuels.

Ralph Jansen↗
NASA NTRS1955

Aerodynamic Characteristics of Various Configurations of a Model of a 45 Degree Swept-wing Airplane at a Mach Number of 2.01

An investigation has been conducted at the Langley 4- by 4-foot supersonic pressure tunnel at a Mach nmber of 2.01 to determine the aerodynamic characteristics of several configurations of a model of a 45 deg swept-wing airplane. The basic configuratin had a wing with 45 deg sweepback at the quarter-chord line, aspect ration 3.2, taper ration 0.468, NACA 65A005.5 sections just outboard of the inlet and NACA 65A003.7 sections at the tip. The wing was mounted slightly above the body center line and an all-movable horizantal tail was located slightly below the extended chord line of the wing. Tre design incorporated twin wing-root supersonic inlets ducted to a single exit at the base of the fuselage. The configurations investigated included an extended nose length, a bumped-fuselage afterbody, an inlet droop, an lncreased wing aspect ratio, and a revised canopy shape. Configurations employing the wing of increased aspect ratio of 3.7, which constituted the bulk of the tests, produced about a 10-percent increase in lift and in longitudinal stability as compared with the basic wing of aspect ratio 3.2. There was a slight but masurable increase in minimum drag and maximum lift-drag ratio.

Spearman, Leroy M↗
NASA NTRS1993

A high resolution ultraviolet Shuttle glow spectrograph

The High Resolution Shuttle Glow Spectrograph-B (HRSGS-B) is a small payload being developed by the Naval Research Laboratory. It is intended for study of shuttle surface glow in the 180-400 nm near- and middle-ultraviolet wavelength range, with a spectral resolution of 0.2 nm. It will search for, among other possible features, the band systems of excited NO which result from surface-catalyzed combination of N and O. It may also detect O2 Hertzberg bands and N2 Vegard-Kaplan bands resulting from surface recombination. This wavelength range also includes possible N2+ and OH emissions. The HRSGS-B will be housed in a Get Away Special canister, mounted in the shuttle orbiter payload bay, and will observe the glow on the tail of the orbiter.

Carruthers, George R.↗
NASA NTRS1991

The FM-007: An advanced jet commuter for HUB to spoke transportation

Due to the increasing need for new commuter aircraft, the FM-007 is proposed, a technologically advanced jet propelled short takeoff and landing (STOL) airplane. The proposed commuter is designed for hub to spoke air travel. In order to reduce drag, natural laminar flow technology is integrated into the design using the natural laminar flow airfoil section for the wing. A three lifting surface configuration provides for more efficient cruise flight. This unique design includes a small forward wing (canard), a rear mounted high aspect ratio main wing, and a small horizontal stabilizer high atop the vertical tail. These three surfaces act together to reduce drag by minimizing the downward force the horizontal stabilizer has to account for due to the nose down pitching moment. Commuter aircraft must also incorporate passenger comfort. This is achieved by providing a spacious pressurized cabin with a large galley and reduced cabin noise due to incorporation of noise reduction gear. A basic oval design is adopted, as opposed to a circular design in order to allow for the seating of five passengers abreast. To get STOL capability, an over the wing blown flap is used using a Rolls Royce Tay series engine.

Blouke, Peter Scott↗
NASA NTRS2015

Cart3D Analysis of Plume and Shock Interaction Effects on Sonic Boom

A plume and shock interaction study was developed to collect data and perform CFD on a configuration where a nozzle plume passed through the shock generated from the wing or tail of a supersonic vehicle. The wing or tail was simulated with a wedge-shaped shock generator. Three configurations were analyzed consisting of two strut mounted wedges and one propulsion pod with an aft deck from a low boom vehicle concept. Research efforts at NASA were intended to enable future supersonic flight over land in the United States. Two of these efforts provided data for regulatory change and enabled design of low boom aircraft. Research has determined that sonic boom is a function of aircraft lift and volume distribution. Through careful tailoring of these variables, the sonic boom of concept vehicles has been reduced. One aspect of vehicle tailoring involved how the aircraft engine exhaust interacted with aft surfaces on a supersonic aircraft, such as the tail and wing trailing edges. In this work, results from Euler CFD simulations are compared to experimental data collected on sub-scale components in a wind tunnel. Three configurations are studied to simulate the nozzle plume interaction with representative wing and tail surfaces. Results demonstrate how the plume and tail shock structure moves with increasing nozzle pressure ratio. The CFD captures the main features of the plume and shock interaction. Differences are observed in the plume and deck shock structure that warrant further research and investigation.

supersonic wind tunnels↗
NASA NTRS2018

Stabilizer Sacrificial Surfaces

An aircraft assembly is disclosed and includes a fuselage including a turbine engine mounted within the aft fuselage. A burst zone is defined about the turbine engine and a tail is disposed at least partially with the burst zone. The tail includes primary control surfaces and sacrificial control surfaces. The sacrificial control surfaces can break away in a defined manner to maintain integrity of the primary control surfaces outside of the burst zone.

Chandler, Jesse M.↗
NASA NTRS1990

Electro-optical spin measurement system

An electro-optical spin measurement system for a spin model in a spin tunnel includes a radio controlled receiver/transmitter, targets located on the spin model, optical receivers mounted around the perimeter of the spin tunnel and the base of the spin tunnel for receiving data from the targets, and a control system for accumulating data from the radio controlled receiver and receivers. Six targets are employed. The spin model includes a fuselage, wings, nose, and tail. Two targets are located under the fuselage of the spin model at the nose tip and tail. Two targets are located on the side of the fuselage at the nose tip and tail, and a target is located under each wing tip. The targets under the fuselage at the nose tip and tail measure spin rate of the spin model, targets on the side of the fuselage at the nose tip and tail measure angle of attack of the spin model, and the targets under the wing tips measure roll angle of the spin model. Optical receivers are mounted at 90 degree increments around the periphery of the spin tunnel to determine angle of attack and roll angle measurements of the spin model. Optical receivers are also mounted at the base of the spin tunnel to define quadrant and position of the spin model and to determine the spin rate of the spin model.

Fodale, Robert↗
NASA NTRS1973

Supersonic aerodynamic characteristics of hypersonic low-wave-drag elliptical body-tail combinations as affected by changes in stabilizer configuration

An investigation has been made at Mach numbers from 1.50 to 4.63 to determine systematically the effects of the addition and position of outboard stabilizers and vertical- and vee-tail configurations on the performance and stability characteristics of a low-wave-drag elliptical body. The basic body shape was a zero-lift hypersonic minimum-wave-drag body as determined for the geometric constraints of length and volume. The elliptical cross section had an axis ratio of 2 (major axis horizontal) and an equivalent fineness ratio of 6.14. Base-mounted outboard stabilizers were at various dihedral angles from 90 deg to minus 90 deg with and without a single center-line vertical tail or a vee-tail. The angle of attack was varied from about minus 6 to 27 deg at sideslip angles of 0 and 5 deg and a constant Reynolds number of 4.58 x one million (based on body length).

Spencer, B., Jr.↗
NASA NTRS2015

Direct Simulation of Flow over A Wall-Mounted Hump

Simulating separated flows at high Reynolds numbers using Reynolds Averaged Navier-Stokes (RANS) modeled equations remains a challenge in aeronautics. The main hindrance to progress stems from the lack of extended de- tailed data pertinent to the root cause of failure of RANS models, as well as the little progress in RANS modeling innovations in the past several decades. The goal of the current effort is to generate data for separated flow at a Reynolds numbers where conventional models are challenged. We use Direct Numerical Simulations to model turbulent flow over the wall-mounted hump configuration to investigate the physics of flow separation and boundary layer recovery, as well as provide data relevant to the modeling community. A chord-based Reynolds number of Re(sub c) = 47,500 is considered with a turbulent inflow profile of Re(sub θ) = 1,400 (θ /c = 3%). We use FDL3DI, a code that solves the compressible Navier-Stokes equations using high-order compact-difference scheme and filter, with the standard re- cycling/rescaling method of generating turbulent boundary layers as inflow to the computational domain. Two differ- ent configurations of the upper-wall are analyzed for two sets of boundary conditions (slip and no-slip). The results are compared with the available higher Re(sub c) (= 936,000, Re(sub θ) = 7,200, θ /c = 0.77%) experiment for major flow features. The simulated lower Rec allows for DNS-like mesh resolutions, and adequately wide spans. The results from these simulations show earlier separation and delayed reattachment compared to Re(sub c) = 936,000, and significantly higher skin friction in the forebody of the hump. We also find that the upper-wall shape and boundary condition influence pressure distribution over the hump, whereas skin friction is only influenced by the boundary condition.

Wall-Mounted↗
NASA NTRS1991

Model rotor icing tests in the NASA Lewis icing research tunnel

Tests of a lightly instrumented two-bladed teetering rotor and a heavily instrumented sub-scale articulated main rotor were conducted in the NASA Lewis Research Center Icing Research Tunnel (IRT) in August 1988 and September and November 1989. The first was an OH-58 tail rotor which had a diameter of 1.575 m and a blade chord of 0.133 m, and was mounted on a NASA designed test rig. The second, a four bladed articulated rotor, had a diameter of 1.83 m with 0.124 m chord blades specially fabricated for the experiment. This rotor was mounted on a Sikorsky Aircraft Powered Force Model, which enclosed a rotor balance and other measurement systems. The models were exposed to variations in temperature, liquid water content, and medium droplet diameter, and were operated over ranges of advance ratio, shaft angle, tip Mach number (rotor speed), and weight coefficient to determine the effect of these parameters on ice accretion. In addition to strain gage and balance data, the test was documented with still, video, and high speed photography, ice profile tracing, and ice molds. Presented here are the sensitivity of the model rotors to the test parameters and a comparison of the results to theoretical predictions.

Flemming, Robert J.↗
NASA NTRS1991

Model rotor icing tests in the NASA. Lewis Icing Research Tunnel

Tests of a lightly instrumented two bladed teetering rotor and a heavily instrumented subscale articulated main rotor were conducted in the NASA Lewis Icing Research Tunnel (IRT). The first was an OH-58 tail rotor which had a diameter of 1.575 m and a blade chord of 0.133 m, and was mounted on a NASA designed test rig. The second, a four bladed articulated rotor, had a diameter of 1.83 m with 0.124 m chord blades specifically fabricated for the experiment. This rotor was mounted on a Sikorsky Aircraft Powered Force Model, which enclosed a rotor balance and other measurement systems. The models were exposed to variations in temperature, liquid water content, and medium droplet diameter, and were operated over ranges of advance ratio, shaft angle, tip Mach number (rotor speed), and weight coefficient to determine the effect of these parameters on ice accretion. In addition to strain gage and balance data, the test was documented with still, video, and high speed photography, ice profile tracing, and ice molds. The sensitivity is presented of the model rotors to the test parameter and a comparison of the results to theoretical predictions.

Flemming, Robert J.↗