Search NASA⌕ Search

SEARCH · Search NASA

Results for “TENSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Garnet melt viscosity, surface tension and drainage

Good surface morphology and layer uniformity of LPE-grown Bi YIG films are favored by fast melt removal after growth. Three flux modifying oxides: MoO3, V2O3, and WO3 are compared with respect to their effect on viscosity, surface tension and melt drainage. All three oxides increased the viscosities of Bi-garnet melts, but the viscosities and drainage times of V2O3 and MoO3 modified melts were smaller than those of WO3 modified melts. The liquid-gas surface tension was found to be temperature independent. The drainage process was strongly temperature dependent, 40 to 60 kcal/mol, whereas the viscosities of melts had activation energies of 11 to 16 kcal/mol. Contact angles of 16 + or - 2 deg were measured on frozen melt drops.

Luther, L. C.↗
NASA NTRS1985

Surface-tension-driven flow in a glass melt

Motion driven by surface tension gradients was observed in a vertical capillary liquid bridge geometry in a sodium borate melt. The surface tension gradients were introduced by maintaining a temperature gradient on the free melt surface. The flow velocities at the free surface of the melt, which were measured using a tracer technique, were found to be proportional to the applied temperature difference and inversely proportional to the melt viscosity. The experimentally observed velocities were in reasonable accord with predictions from a theoretical model of the system.

Mcneil, Thomas J.↗
NASA NTRS1984

The effect of anisotropic crystal-melt surface tension on grain boundary groove morphology

The shape of a stationary solid-liquid interface in a temperature gradient near a grain boundary in a pure material is calculated for anisotropic crystal-melt surface tension and equal thermal conductivities of crystal and melt. Results are compared with those for the well-known problem of the two-dimensional equilibrium shape of a crystal. For small anisotropy, the resulting interface shapes have continuously turning tangents but differ in detail from the grain boundary groove shapes that have been calculated for isotropic surface tension. For larger anisotropy, the interface shapes have discontinuities in slope as a result of missing orientations.

Voorhees, P. W.↗
NASA NTRS1988

Interfacial tension and vapor-liquid equilibria in the critical region of mixtures

In the critical region, the concept of two-scale-factor universality can be used to accurately predict the surface tension between near-critical vapor and liquid phases from the singularity in the thermodynamic properties of the bulk fluid. In the present work, this idea is generalized to binary mixtures and is illustrated using the data of Hsu et al. (1985) for CO2 + n-butane. The pressure-temperature-composition-density data for coexisting, near-critical phases of the mixtures are fitted with a thermodynamic potential comprised of a sum of a singular term and nonsingular terms. The nonuniversal amplitudes characterizing the singular term for the mixtures are obtained from the amplitudes for the pure components by interpolation in a space of thermodynamic 'field' variables. The interfacial tensions predicted for the mixtures from the singular term are within 10 percent of the data on three isotherms in the pressure range (Pc - P)/Pc of less than 0.5. This difference is comparable to the combined experimental and model errors.

Moldover, Michael R.↗
NASA NTRS1988

Effect of surface tension anisotropy on cellular morphologies

A three-dimensional weakly nonlinear analysis for conditions near the onset of instability at the crystal-melt interface was carried out to second order, taking into account the effects of latent heat generation and surface-tension anisotropy of the crystal-melt interface; particular consideration was given to the growth of a cubic crystal in the 001-, 011-, and 111-line directions. Numerical calculations by McFadden et al. (1987), performed for an aluminum-chromium alloy with the assumption of a linear temperature field and an isotropic surface tension, showed that only hexagonal nodes (and not hexagonal cells) occurred near the onset of instability. The results of the present analysis indicate that the nonlinear temperature field (which occurs when thermal conductivities of the crystal and the melt are different and/or the latent heat effects are not negligible) can modify this result and, for certain alloys and processing conditions, can cause the occurrence of hexagonal cells near the onset of instability.

Mcfadden, G. B.↗
NASA NTRS1988

Development of a space qualified Surface Tension Confined Liquid Cryogen Cooler (STCLCC)

The Surface Tension Confined Liquid Cryogen Cooler (STCLCC), a new type of cryogenic cooler which is being developed by the NASA-GSFC for spaceflight payloads, is described. The STCLCC will be capable of maintaining instrumentation within the temperature range of 10-120 K and will allow liquid cryogens to be flown in space without the risk of liquid being entrained in the vent gas. A low-density open-cell material in the STCLCC acts as a 'sponge', with the surface tension trapping the liquid cryogen within its pores and keeping the liquid away from the cooler's vent during launch, zero-g operations, and landing. It is emphasized that the STCLCC concept is amenable to a wide variety of applications, whenever a passive low-cost cooler is required or when the on-orbit service of a cooler would increase a mission's lifetime.

Castles, Stephen H.↗
NASA NTRS1988

Tension fatigue analysis and life prediction for composite laminates

A tension fatigue life prediction methodology for composite laminates is presented. Tension fatigue tests were conducted on quasi-isotropic and orthotropic glass epoxy, graphite epoxy, and glass/graphite epoxy hybrid laminates. Edge delamination onset data were used to generate plots of strain energy release rate as a function of cycles to delamination onset. These plots were then used along with strain energy release rate analyses of delaminations initiating at matrix cracks to predict local delamination onset. Stiffness loss was measured experimentally to account for the accumulation of matrix cracks and for delamination growth. Fatigue failure was predicted by comparing the increase in global strain resulting from stiffness loss to the decrease in laminate failure strain resulting from delaminations forming at matrix cracks through the laminate thickness. Good agreement between measured and predicted lives indicated that the through-thickness damage accumulation model can accurately describe fatigue failure for laminates where the delamination onset behavior in fatigue is well characterized, and stiffness loss can be monitored in real time to account for damage growth.

Obrien, T. K.↗
NASA NTRS1988

An experimental and analytical evaluation of the tapered tension-torsion strap concept

A new free-tip rotor moment controller designed to increase torque output (a restoring moment) was proposed. The controller would be used as a retention device for the freely pitching tip of a helicopter rotor. The new design featured a tapered tension-torsion strap instead of the previously used parellel strap. A tapered strap has a larger separation between the tension wires at the retention end than at the oscillating end; separation is equal at both ends for a parallel strap. A simple dynamic analysis was developed and an experiment performed to evaluate this tapered strap concept. The test results indicated that the torsional spring stiffness of the strap, represented by a torsional pendulum, increased with the amount of taper. The predicted dynamic characteristics of the pendulum also confirmed this observation and correlated reasonably well with the experimental results. It could be concluded from the experimental and analytical results that the tapered strap accomplished increased torque output when compared to the parellel strap.

Louie, Alexander↗
NASA NTRS1988

Fluoride glass: Crystallization, surface tension

Fluoride glass was levitated acoustically in the ACES apparatus on STS-11, and the recovered sample had a different microstructure from samples cooled in a container. Further experiments on levitated samples of fluoride glass are proposed. These include nucleation, crystallization, melting observations, measurement of surface tension of molten glass, and observation of bubbles in the glass. Ground experiments are required on sample preparation, outgassing, and surface reactions. The results should help in the development and evaluation of containerless processing, especially of glass, in the development of a contaminent-free method of measuring surface tensions of melts, in extending knowledge of gas and bubble behavior in fluoride glasses, and in increasing insight into the processing and properties of fluoride glasses.

Doremus, R. H.↗
NASA NTRS1989

An analytical and experimental investigation of edge delamination in laminates subjected to tension, bending, and torsion

An integrated two-dimensional finite element was developed to calculate interlaminar stresses and strain energy release rates for the study of delamination in composite laminates subjected to uniaxial tension, bending, and torsion loads. Addressed are the formulation, implementation, and verification of the model. Parametric studies were conducted on the effect of Poisson's ratio mismatch between plies and the stacking sequence on interlaminar stress, and on the effect of delamination opening height and delamination length, due to bending, on strain energy release rate for various laminates. A comparison of strain energy release rates in all-graphite and graphite/glass hybrid laminates is included. The preliminary results of laminates subjected to torsion are also included. Fatigue tension tests were conducted on Mode 1 and mixed mode edge-delamination coupons to establish the relationship between fatigue load vs. onset of delamination cycle. The effect on the fatigue delamination onset of different frequencies (1 and 5 Hz) was investigated for glass, graphite,and their hybrid laminates. Although a 20 percent increase in the static onset-of-delamination strength and a 10 percent increase in ultimate strength resulted from hybridizing the all-graphite laminate with a 90 deg glass ply, the fatigue onset is lower in the hybrid laminate than in the all-graphite laminate.

Chan, Wen S.↗
NASA NTRS1988

Acoustic measurement of the surface tension of levitated drops

The measurement of the frequency of the fundamental mode of shape oscillation of acoustically levitated drops has been carried out to determine the surface tension of the drop material. Sound fields of about 20 kHz in frequency allow the suspension of drops a few millimeters in size, as well as the necessary drive for oscillations. The surface tension of water, hexadecane, silicone oil, and aqueous solutions of glycerin levitated in air has been measured, and the results have been compared with those obtained with standard ring tensiometry. The two sets of data are in good agreement, the largest discrepancy being about 10 percent. Uncertainties in the effects of the nonspherical static shape of drops levitated in the earth's gravitational field and the rotation state of the sample are the major contributors to the experimental error. A decrease of the resonance frequency of the fundamental mode indicates a soft nonlinearity as the oscillation amplitude increases.

Trinh, E. H.↗
NASA NTRS1987

Calculation of the surface tension of liquid metals using a one-component-plasma reference system

The one-component-plasma (OCP) model is used as a reference system instead of the traditional hard-sphere fluid to calculate the liquid-vapor interfacial surface tension of liquid metals within the density functional formalism. The calculated surface tensions of the alkali metals are in excellent agreement with experiment. For the polyvalent metal Al, the result obtained is larger than experimental measurements. It is concluded that the OCP system is not suitable to describe the liquid-vapor phase transition in simple metals which have a nominal plasma parameter larger than the usual freezing value of about 178. The calculated interfacial widths in all cases are narrower than the expected experimental values.

Zeng, X. C.↗
NASA NTRS1989

Surface tension measurements of aqueous ammonium chloride (NH4Cl) in air

Aqueous NH4Cl's solidification is often used to model metal alloy solidification processes. The present determinations of the magnitude of the variation of aqueous NH4Cl's surface tension as a function of both temperature and solutal concentration were conducted at 3, 24, and 40 C over the 72-100 wt pct water solutal range. In general, the surface tension increases 0.31 dyn/cm per percent decrease in wt pct of water, and decreases 0.13 dyn/cm for each increase in deg C. Attention is given to the experimental apparatus employed.

Lowry, S. A.↗
NASA NTRS1990

Edge delamination of composite laminates subject to combined tension and torsional loading

Delamination is a common failure mode of laminated composite materials. Edge delamination is important since it results in reduced stiffness and strength of the laminate. The tension/torsion load condition is of particular significance to the structural integrity of composite helicopter rotor systems. Material coupons can easily be tested under this type of loading in servo-hydraulic tension/torsion test stands using techniques very similar to those used for the Edge Delamination Tensile Test (EDT) delamination specimen. Edge delamination of specimens loaded in tension was successfully analyzed by several investigators using both classical laminate theory and quasi-three dimensional (Q3D) finite element techniques. The former analysis technique can be used to predict the total strain energy release rate, while the latter technique enables the calculation of the mixed-mode strain energy release rates. The Q3D analysis is very efficient since it produces a three-dimensional solution to a two-dimensional domain. A computer program was developed which generates PATRAN commands to generate the finite element model. PATRAN is a pre- and post-processor which is commonly used with a variety of finite element programs such as MCS/NASTRAN. The program creates a sufficiently dense mesh at the delamination crack tips to support a mixed-mode fracture mechanics analysis. The program creates a coarse mesh in those regions where the gradients in the stress field are low (away from the delamination regions). A transition mesh is defined between these regions. This program is capable of generating a mesh for an arbitrarily oriented matrix crack. This program significantly reduces the modeling time required to generate these finite element meshes, thus providing a realistic tool with which to investigate the tension torsion problem.

Hooper, Steven J.↗
NASA NTRS1990

Surface tension and viscosity from damped free oscillations of viscous droplets

Damped oscillations of a viscous droplet in vacuum or in an inert gas of negligible density are considered. The dependence of the complex decay factor on the properties of the liquid is investigated for the first time, and numerical results are compared with earlier studies for special cases. A new method is developed to determine both surface tension and viscosity from a single experiment in which the damping rate and frequency of oscillations are measured. The procedure to determine surface tension and viscosity from oscillating levitated liquids is outlined, and results presented for various modes of shape oscillations.

Suryanarayana, P. V. R.↗
NASA NTRS1990

Critical-point analysis of the liquid-vapor interfacial surface tension

The interfacial surface tension of the liquid-vapor system is analyzed near the critical point in a manner similar to bulk thermodynamic critical-point analyses. This is accomplished by a critical-point analysis of the single-phase hard-wall surface tension. Both a Landau expansion and a scaling theory equation of state are investigated. Some general exponent relations are derived and, in addition, some thermodynamically defined correlation lengths are discussed.

Salvino, R. E.↗
NASA NTRS1991

The wavelength of supercritical surface tension driven Benard convection

The size or the wavelength of moderately supercritical surface tension driven Benard convection has been investigated experimentally in a thin fluid layer of large aspect ratio. It has been found that the number of the hexagonal convection cells increases with increased temperature differences, up to 1.3 times the critical temperature difference. That means that the wavelength of surface tension driven convection decreases after onset of the instability for moderately nonlinear conditions. This result is in striking contrast to the well-known increase of the wavelength of buoyancy driven Rayleigh-Benard convection.

Koschmieder, E. L.↗
NASA NTRS1991

The fatigue behaviour of orthotropic laminates under tension-compression loading

The fatigue behavior of orthotropic laminates (0, +/-45, 0 deg)2s and (90, +/-45, 90 deg)2s, has been evaluated under alternating tension-compression loading. Even though the first laminate is much stronger than the second, both started to fail by delamination. Visual damage started to show only at the very end of the fatigue life but measurement of the stiffness showed that degradation starts at about 80 percent of the fatigue life. The first laminate failed in compression after delamination between the 0 and the 45 deg laminae, while the second failed in tension after delamination between the +45 and -45 deg laminae. It is shown that the interlaminar fatigue strength of both laminate structures can be correlated to the applied fatigue load.

Rotem, A.↗