Separate Effects Testing of TRISO Fuel Particles using the MiniFuel Irradiation Vehicle
Explore the source record for details and available documents.
Gerczak, Tyler↗
SEARCH · Search NASA
Results for “TEST PARTICLES”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Refining Methods to Determine the Isotopic Composition of Uranium Particles by Laser Ablation MC-ICP-MS
We report on efforts to mitigate the generation of isotopic anomalies during the ablation of micrometer-sized uranium oxide particles and analysis by MC-ICP-MS. The results of testing on particles of U200 indicate that laser fluence and frequency can affect isotopic data produced by laser ablation, but no settings were tested that could eradicate the signal spiking effect and generation of anomalous isotopic data for 234U/238U and 236U/238U. These anomalies are more frequent in samples with higher 235U enrichments, which is expected given their higher abundances of 234U and 236U. Of the standards tested here, only U005-A was anomaly-free. Efforts to compare the laser traces for particles with normal and anomalous isotopic compositions showed subtle differences in the behavior of the 234U/238U and 236U/238U ratios. However, it would be challenging to identify anomalous data points from a population of unknowns using this distinction, i.e., this is unlikely to be diagnostic. Thus, using current analytical hardware, we cannot eradicate the signal spiking phenomenon and cannot unambiguously identify isotopic anomalies from laser ablation traces. Ultimately, laser ablation ICP-MS would either require dramatic improvement to the ablation process and generation of more homogenous aerosols and/or improvements to detector electronics to identify and correct for the spiking phenomenon. Even if the reliability of the technique could be improved, a broader question to address is whether current data quality is of a high enough standard for laser ablation MC-ICP-MS to be used as a complementary technique to LG-SIMS for Safeguards.
organic↗
Integrated Process Testing of MSR Salt Spill Accidents
Part of the licensing process for new nuclear reactors requires vendors to assess the potential consequences of identified accident scenarios using accident progression modeling. The accident scenario that will likely be evaluated by all molten salt reactor (MSR) developers is a spill of radionuclide-bearing fuel salt onto the reactor containment floor (i.e., a salt spill accident). The development of accident progression models requires experimental data to inform which processes to incorporate, to enable the calculation of parameters to model these processes, and to validate the model predictions. The data should quantify the sensitivities of key processes (e.g., molten salt spreading, heat transfer, containment structure corrosion, radionuclide vaporization, and aerosol generation) towards the initial conditions of the spill, the ambient environment, and the features of the containment. In addition, results from integrated process tests that quantify coupled processes are required to validate systems-level models. This report documents results from integrated process tests conducted on simulated molten salt spill accidents. The generated experimental data simultaneously quantify the heat transfer behavior of the spilled salt, compositional changes to the bulk salt, and the release of surrogate fission products from the spilled salt as aerosol particles. All tests that were conducted used FLiNaK doped with surrogate fission products, and the variables that were evaluated included the initial salt temperature and the concentration of surrogate fission products present in the salt. The major accomplishments of this work include identifying surrogate fuel salt compositions that provide insight into the dispersal behavior of radionuclides of potential significance to the source term, employing previously developed methods and measurement techniques to simultaneously measure key processes, generating data on the coupled processes of molten salt heat transfer and surrogate fission product release as aerosol particles, demonstrating new test methods for real-time monitoring of the flow rate of the spill and aerosol size quantification in an argon atmosphere, and developing a mass transfer model for cesium and iodine release from molten FLiNaK to provide insight into aerosol formation by vapor condensation. The same methodology applied herein can be employed to study different salt compositions of interest to MSR developers, different environmental conditions, and other variables that are relevant to postulated accident scenarios. The insights gained from these integrated process tests conducted at a laboratory scale will be incorporated into future integral effects tests conducted at an engineering scale.
20 FOSSIL-FUELED POWER PLANTS↗
Towards an understanding of particle-scale flaws and microstructure evolution in cold spray via accumulation of single particle impacts
Cold spray coatings are the sum of countless individual bonding events between single particles impacting on top of one another at high velocities. Thus, the collective behavior of microparticles must be considered to elucidate the origins of coating flaws at the scale of the particles and larger, or the dynamic evolution of the overall coating microstructure. Laser-induced particle impact testing (LIPIT) has been extensively used to study single-particle impacts, and in this work is adapted to study the accumulation of numerous particles with knowledge of each individual particle's impact parameters (particle size, velocity). The method reproducibly deposits stacks of gold particles (>20 particles) with different characteristic spectra of impact velocity. The observation of impact-induced erosion lets us define a critical velocity for material-build-up that is higher than that for single-particle bonding. The quantitative single-particle data are analyzed in a correlative manner to the structure and flaws in the resulting stacks, providing some first statistical connections between, e.g., strain and recrystallization, or aberrant particle characteristics and defects. The results highlight opportunities for the study of many-particle phenomena in microparticle impact—from interaction of particles in cold spray to multi-step erosion processes—with a quantitative view of the behavior of single particles.
Erosion↗
Failure analysis of nuclear transient-tested UN tristructural isotropic fuel particles in a 3D printed SiC matrix
Fully ceramic microencapsulated fuel elements containing UN tristructural isotropic (TRISO) fuel particles within a 3D printed SiC matrix were subjected to transient testing with varying energy depositions. Detailed post-irradiation examinations were performed, including leaching in hot HNO3 and post-leaching X-ray computed tomography, to quantify the percentage of failed TRISO particles and crack propagation within the particles and surrounding fuel matrix. In parallel, detailed finite element analyses were performed for comparison with experimental findings and to better evaluate transient failure modes. The lowest transient energy deposition—which still exceeded bounding values for high-temperature gas-cooled reactor applications—resulted in no detectable TRISO particle failures or matrix cracking, which was consistent with the simulations. Simulations of the higher-energy transients for which significant TRISO particle failure was expected were generally able to reproduce the transient temperatures and matrix cracking. Thus, the TRISO particle failures were explained based on the effects of local SiC matrix thickness and porosity. Results generally confirmed the high strength of the additively manufactured SiC matrix but also affirmed the need for a modified UN TRISO architecture to prevent SiC matrix cracks from propagating through TRISO layers. This unique failure mode has not historically been considered for TRISO fuels contained in weaker graphite matrices.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Low-cost production method for fluorescent particles for liquid flow velocimetry applications
Abstract In this Technical Note, we present a simple and low-cost production method for fluorescent particles perfectly suitable for velocimetry applications. We leverage the unique ability of Nile Red (NR) fluorophores to adsorb on the polymer surface and/or embed itself in between polymeric chains. The laboratory procedure to dye polyamide particles with NR and monetary advantages over commercially available fluorescent particles is outlined. Subsequently, the fluorescence behavior of the dyed particles is tested under a laser illumination source in polar and non-polar liquids. The distinct advantage of the emission spectrum of NR-dyed particles is demonstrated with sample test results.
42 ENGINEERING↗
Self-consistent hardness measurements spanning eleven decades of strain rate on a single material surface
A comprehensive understanding of material strength across strain rates typically requires the combination of results from different methods, which often vary in loading conditions and/or sampled volumes, leading to discrepancies in material behavior. This study presents a microindentation approach to measure hardness covering eleven orders of magnitude in strain rate, from quasi-static to phonon drag-dominated rates, on a single material surface under uniform testing conditions. By engineering the geometry of impactors used in laser induced particle impact testing, we extend the breadth of accessible strain rates, including multiple distinct rates exceeding 10⁵ s⁻¹. This self-consistent approach provides clearer insights into high-rate deformation mechanisms. Our results demonstrate a gradual increase in hardness with strain rate from quasi-static up to ultra-high rates, where a sharp upturn in hardness is observed.
Engineering↗
Assessment of Thin Plastic Scintillation Detectors for Beta-Particle Measurements at the Advanced Test Reactor Critical Facility
The Fission Wire Measurement System is a custom measurement system designed in the 1960s to measure the beta-particle activity of irradiated uranium-aluminum fission wires. This measurement is conducted to determine the fission rate profile of the Advanced Reactor Test Critical facility. The Advanced Test Reactor Critical facility is an open-pool, low-power test reactor used to qualify experiment configurations and verify core models prior to full-power experiment irradiations in the Advanced Test Reactor. Power distribution measurements in ATR-C use uranium-aluminum wires that are distributed throughout the core to validate simulation and modeling results. These measurements require from 340 to 1500 wires to be irradiated and measured within a 12-hour window. The system consists of 4 measurement channels and one reference channel, each with a 2-pi proportional gas flow detector and the measurement channels each have an automated sample changer. The gas flow detectors are of a custom design for this detector system that use methane gas with a large anode wire compared to modern proportional counters. These detectors, which are nearly 60 years old are irreplaceable. The measurements from these gas detectors are affected by the gas flow rate, atmospheric and line pressure, and are very sensitive to the applied high voltage. Recent improvements have been made to the control and data acquisition system, but the detectors have remained the same. The nature of the measurement of the fission product decay activity is such that the energy spectrum of the signal is changing with time. Thin, 250-um thick, plastic scintillators were commercially obtained as a potential replacement for the gas flow detectors. The original calibration of the uranium-aluminum fission wires was conducted in 1965 using a series of irradiations of gold foils and the wires in a well-characterized thermal neutron field. These measurements provided a time-dependent fission rate conversion factor from the gold foil data to calibrate the fission wires based on the response from the 2-pi proportional gas detectors. Transitioning to the new detectors requires qualification and testing. The sensitivity of the scintillators to changes in the energy spectrum of the fission wires and translation of the calibration factor have been completed. These measurements indicated that the sensitivity of the scintillators over time changes at a different rate than the sensitivity of the gas flow detectors. However, the inverse activity of measurements of both detector types is linear with time. Initial results indicate that the scintillator detectors will be a sufficient replacement for the gas detectors with minor adjustments to the fission rate conversion factor. Replacement of the detectors will improve the fission wire measurements and provide a more stable and reliable measurement system.
46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
Heat Transfer Characteristics of Particle Flow Through Additively Manufactured (SS 316L) Lattice Frame Material Based on Octet-Shape Topology
Abstract This paper presents experimentally obtained heat transfer characteristics of additively manufactured lattice frame material based on Octet-shaped unit cell. Binder jetting technology was used to print lattices in Stainless Steel 316L material. Lattice porosities ranging from 0.75 to 0.9 were investigated where thermal transport characteristics were obtained for void space occupied by air and particles. Particle diameters were varied from 266–966 microns. Effective thermal conductivity and averaged heat transfer coefficient was calculated through steady-state experiments. It was found that presence of lattice enhances the effective thermal conductivity by 2–4 times when compared to packed bed of particles alone. Furthermore, for gravity-assisted particle flow through lattice panel, significantly high convective heat transfer coefficients ranging from 200–400 W/m2K were obtained for the range of particle diameters tested. The superior thermal transport properties of Octet-shape based lattice frame material for particle flow through them makes it a very promising candidate for particle-to-supercritical carbon dioxide (sCO2) heat exchanger in concentrating solar power (CSP) application.
Aider, Youssef↗
Single particle impact explorations on the role of powder heat treatments in cold spray: Effects of strength and oxide structure
In cold spray, the optimization of the powder feedstock for improving the final properties of the coating and for improving the process itself are two different objectives. This paper explores the latter, studying the relationship between powder pre-heat treatment and the kinetic bonding between the individual particles and the substrate. Using a laser-induced particle impact test (LIPIT), we investigate the effect of different heat treatments on the critical adhesion velocity of Al 6061. Although heat treatments change the strength of the powders as well as the thickness of the native oxide layer each by as much as ∼50 %, the critical adhesion velocity remains constant to within only ∼10 %. A deeper analysis reveals that these two factors change in somewhat complementary ways for the heat treatments explored here, leading to counteracting effects. By quantitatively evaluating these two microstructural factors in tandem, we find that they are roughly equally important in determining the critical adhesion velocity. These observations thus provide insight for the development of new heat treatment regimens that might lower the adhesion velocity.
Al 6061↗
Compositing and Characterization of SE Quadrant Waste Exemplars
This report outlines the experimental investigation and characterization of transport properties in Hanford SE quadrant High-Level Waste (HLW). The goal of the study was to establish baseline behaviors of bulk composite rheology and settling characteristics to facilitate waste treatment process design for the Waste Treatment and Immobilization Plant (WTP) and avoid waste conditions and properties favorable to bubble cascade gas release events. The study focused on two major objectives: 1) identifying, obtaining, and preparing relevant Hanford tank waste samples for evaluation and 2) quantifying the “as-received” rheology and transport properties of the samples. Twenty-three centrifuged core segments originating from tanks AN-101, AN-106, and AW-105 were selected based on compositional relevance to SE quadrant PUREX cladding waste. These materials were composited into five waste composites enriched with target analytes: aluminum (Al), iron (Fe), phosphate (PO 4 ), uranium (U), and zirconium (Zr). Physical property and transport testing examined particle size distributions, bulk densities, settling behaviors, rheological properties, shear strengths, and just-suspended mixing speeds (NJS). Testing revealed two distinct composite classifications based on rheological characteristics: non-Newtonian composites (Fe and PO 4 ) and Newtonian composites (Al, U, and Zr). The Fe and PO 4 composites exhibited slow settling rates and reduced mobilization proclivity, attributable to strong particle-particle interactions and the formation of yield structures within non-Newtonian slurries. In contrast, the Al, U, and Zr composites displayed rapid settling and dense compaction behaviors, indicative of minimal structuring and interactions. Shear strengths for all composites were generally low relative to prior studies of SE quadrant waste, with only the U composite showing elevated strength approaching values reported in previous literature. Repeat shear strength measurements revealed contributions from dense granular material in the U composite and stronger cohesive properties in the Al composite. Settling data highlighted hindered settling behavior, with rates falling more than one order of magnitude below estimates based on Stokes’ law and rate decreasing as composite UDS content increased. NJS testing demonstrated different mobilization behaviors between cohesive and granular composites. The Fe composite required the highest mixing rate for resuspension, while the Al composite was the easiest to resuspend. Comparison of measured NJS against predictions made using the Zwietering correlation suggests non-Newtonian behavior alters resuspension mechanics, rendering non-Newtonian systems more stable against resuspension lift forces relative to their granular counterparts.
12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
Particle Swarm Optimisation for group structure optimization for radiotherapy shielding
Neutron transport simulations are ubiquitous in nuclear engineering because they allow one to model experimental systems and render a model platform for easy perturbation of experimental designs. In addition, simulations allow one to gain experimental insight without actually having to go through the trouble of building a physical experiment. Neutron transport simulations can be stochastic or deterministic based. Stochastic neutron transport simulations are typically simulated using the Monte Carlo method and yield very accurate solutions but are computationally expensive, while deterministic methods are typically faster but can be less accurate. Here we focus on optimizing the accuracy of deterministic neutron transport simulations for radiotherapy simulations. Deterministic neutron transport requires discretization of angle, energy, and space to appropriately analyze the system one is trying to model. Discretization of energy is challenging because of the highly variable neutron flux at certain neutron energies. Improper discretization of energy in the transport model can lead to erroneous results and therefore inaccurate interpretations of the solution. In this study, we evaluate Particle Swarm Optimization (PSO) as a mechanism for selecting optimal group structures for radiotherapy shielding. We tested the particle swarm optimization algorithm on radiotherapy shielding problems using Los Alamos National Laboratory's (LANL) main deterministic transport code PARTISN. Results show that the optimized energy group structures generated from the optimization algorithm outperformed LANL's standard energy group structures, and therefore demonstrate utility in using PSO to expedite computation times due to the increased accuracy obtained with a smaller but optimized group structure. (authors)
43 PARTICLE ACCELERATORS↗
Drift orbit islands of energetic particles due to 3D fields in ITER
In this study, we report a comparative study of the orbit islands formed by the guiding center drift motion of test energetic particles (EPs), including both high-energy deuterium ions and fusion-born α-particles, with respect to the magnetic islands formed by tracing the field lines, for an ITER plasma representing the 15 MA baseline scenario. The particle drift orbit is modified by the presence of static resonant magnetic perturbations (RMPs) of different toroidal mode numbers n (n = 1 and 3 in this study), forming orbit islands in the Poincaré plane by passing EPs. The key findings are as follows. (i) With an n = 1 RMP field, the size of the orbit islands combined with the total RMP field, including the plasma response, is about three times smaller than that obtained by assuming the corresponding vacuum field. (ii) The orbit island size is not sensitive to the EP energy, and is comparable to those of the magnetic islands. (iii) Passing EPs with outward radial orbital drift form orbit islands that shift inward with respect to the corresponding magnetic islands, and vice versa. This radial shift, ΔΨ, measured in the normalized equilibrium poloidal flux, is quantified as ΔΨ ≃ 0.03X for the ITER baseline plasma and assuming n = 1 RMPs, with $X\equiv {(M/{M}_{\mathrm{p}})}^{1/2}{(E[\mathrm{M}\mathrm{e}\mathrm{V}])}^{1/2}{Z}^{-1}$, where M is the particle mass, Mp is the proton mass, E is the particle energy, and Z is the particle charge number. (iv) Trapped EPs do not form drift orbit islands, even in the presence of the 3D fields produced by the 90 kAt ELM control coil current in ITER, and thus possess good confinement properties. Nevertheless, the deformation of the trapped particle drift orbits in the Poincaré plane shows that the canonical toroidal angular momentum of EPs is no longer conserved in the presence of the RMP fields.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Testing dark matter halo properties using self-similarity
ABSTRACT We use self-similarity in N-body simulations of scale-free models to test for resolution dependence in the mass function and two-point correlation functions of dark matter haloes. We use 10243 particle simulations performed with abacus , and compare results obtained with two halo finders: friends-of-friends (fof ), and rockstar . The fof mass functions show a systematic deviation from self-similarity which is explained by resolution dependence of the fof mass assignment previously reported in the literature. Weak evidence for convergence is observed only starting from haloes of several thousand particles, and mass functions are overestimated by at least as much as $20-25{{\ \rm per\ cent}}$ for haloes of 50 particles. The mass function of the default rockstar halo catalogue (with bound virial spherical overdensity mass), on the other hand, shows good convergence of the order of 50 to 100 particles per halo, with no detectable evidence at the few percent level of any systematic dependence for larger particle number. Tests show that the mass unbinding procedure in rockstar is the key factor in obtaining this much improved resolution. Applying the same analysis to the halo–halo two point correlation function, we find again strong evidence for convergence only for rockstar haloes, at separations sufficiently large so that haloes do not overlap. At these separations, we can exclude dependence on resolution at the $5-10{{\ \rm per\ cent}}$ level once haloes have of the order of 50 to 100 particles. At smaller separations results are not converged even at significantly larger particle number, and bigger simulations would be required to establish the resolution required for convergence.
79 ASTRONOMY AND ASTROPHYSICS↗
First observation of antiproton annihilation at rest on argon in the LArIAT experiment
We report the first observation and measurement of antiproton annihilation at rest on argon track and shower multiplicities and particle identification conducted with the LArIAT experiment. Stopping antiprotons from the Fermilab Test Beam Facility’s charged particle test beam are identified using beamline instrumentation and LArIAT’s liquid argon time projection chamber (LArTPC). The charged particle multiplicity from the annihilation vertex is manually evaluated via hand scanning, yielding a mean of 3.2 ± 0.4 tracks and a standard deviation of 1.3 tracks, consistent with a semiautomated reconstruction resulting in 2.8 ± 0.4 tracks and a standard deviation of 1.2 tracks. Both methods are consistent with Monte Carlo simulations within statistical uncertainty. The shower multiplicities and particle identification for outgoing tracks are also consistent with eant4 model predictions. These results, obtained from a low-statistics sample, provide a foundation for higher-statistics studies in larger LArTPCs, which could refine modeling of intranuclear annihilation on argon and inform scenarios such as neutron-antineutron oscillations. Published by the American Physical Society 2025
72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NLR CSP Optical Facilities: Illuminating the Path Forward Through Innovation and Impact: Agreement 38490
This initiative is a multi-faceted project at the National Laboratory of the Rockies (NLR) aimed at strengthening its Concentrating Solar Power (CSP) Optical Facilities to advance the development of low-cost, high-performance materials for solar and other applications. The project's strategy is built on three pillars: strategic stakeholder engagement, diligent facility maintenance and utilization, and the development of new research capabilities. The overarching goal is to ensure the facilities remain state-of-the-art resources for industry and academia, thereby accelerating the conversion of concentrated sunlight into energy. A key driver of the project is an international Advisory Board, which provides critical guidance on research priorities and industry needs, leading to new collaborations and secured funding. This external engagement, combined with proactive outreach to industry partners, ensures the lab's work remains aligned with real-world challenges, including materials durability and performance certification. Significant efforts in facility maintenance have addressed challenges with aging infrastructure. Notable achievements include the complete refurbishment of the hail-damaged Ultra-Accelerated Weathering System (UAWS) and the successful replacement of a failing 15-year-old Lambda 1050 spectrophotometer with a new-generation model, substantially upgrading material characterization capabilities. These maintenance activities were complemented by achieving a prestigious ISO 9001:2015 certification for the Advanced Optical Materials Labs, formally recognizing the quality and reliability of NLR's measurement capabilities. Despite these successes, challenges remain, including high demand for the High Flux Solar Furnace (HFSF) and intermittent failures of other key instruments. The project has delivered major advancements in research techniques and capabilities. At the Flatirons campus, a new indoor laboratory, was established to house advanced deflectometry and photogrammetry systems for heliostat characterization. For on-sun testing, a novel, actively cooled turning mirror was developed for the HFSF, enabling more realistic testing of particle receivers and components. A collaboration with Virginia Tech successfully demonstrated the high-temperature durability of a new solar absorber coating through extensive cyclic testing. Concurrently, new modeling took place to better predict material degradation on rough, fractal surfaces. In summary, this project has systematically enhanced NLR's CSP Optical Facilities through strategic upgrades, rigorous maintenance, and stakeholder-guided research. By overcoming equipment failures, budgetary constraints, and logistical hurdles, the project has reinforced NLR's role as a central hub for CSP innovation and materials testing. Future work will focus on securing diverse funding, expanding collaborations, and continuing to provide the critical infrastructure needed to accelerate the development and deployment of next-generation technologies.
14 SOLAR ENERGY↗
Observation of Antiproton Annihilation at Rest in LArIAT
Antiproton annihilation at-rest can provide a unique probe into the intra-nuclear structure of nuclei. This process was first observed in the 1950’s using photographic emulsion and has since been observed and studied on a variety of nuclei. We present here the first observation and reconstruction of antiproton annihilation at-rest interactions on argon nuclei using data from the LArIAT experiment, a liquid argon time projection chamber (LArTPC). LArIAT was exposed to a charged particle test-beam at Fermilab from 2015-2017. Antiprotons tagged using LArIAT’s beamline instrumentation were reconstructed in the LArTPC, and the multiplicities of final-state particles emerging from the identified annihilation at-rest vertex were measured. These results will inform searches for neutron-antineutron oscillation events in the future LArTPCs like DUNE due to their similar topological signature.
72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
Design and Operation of a Charged Particle Beamline for the NOvA Test Beam Experiment [Poster]
Abstract not provided.
72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗