Search NASA⌕ Search

SEARCH · Search NASA

Results for “Turbulence measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Application of a laser velocimeter for remote wind velocity and turbulence measurements.

Demonstration of the utility of a laser Doppler-type instrument for studying the velocity structure of atmospheric flow. Its value lies in the fact that regions of interest can be sensed remotely without introducing a perturbation at that location. The absence of moving mechanical parts results in a sensor with high frequency response capability. Regions of the atmosphere to be monitored can be selected simply by deflecting a mirror and adjusting the position of the focusing lens.

Lawrence, T. R.↗
NASA NTRS1973

Three-dimensional gas turbulence measurement with a laser-Doppler velocimeter system

Laser-Doppler system records gas-velocity data over wide dynamic range in three-dimensional space without physical probe. System detects shift in laser beam scattered by flowing particles and uses this frequency to calculate particle velocities. Technique is based on principle that laser beam scattered by flowing particles is shifted in frequency by amount proportional to laser frequency.

Fuller, C. E.↗
NASA NTRS1974

Turbulent measurements in supersonic boundary layer flows using laser velocimetry

Laser velocimetry has been applied successfully in the measurement of mean velocities and Reynolds stresses in a zero pressure gradient, Mach 2.9 boundary layer, and upstream and downstream of a two-dimensional, shock-wave boundary layer interaction for the same Mach number. The Reynolds stresses were obtained using a one-component, dual-scatter laser velocimeter operated in a manner analogous to the 'slanted hot-wire' technique. Signal processing was of the single-particle counting type which permitted measurements to be made using only the naturally occurring particles in the tunnel air stream for light scattering. The results for the shock-wave boundary layer interaction are presented along with hot-wire anemometer and pitot-static pressure measurements obtained in the same flow. Also, a data acquisition scheme for use with a two-component laser velocimeter is presented which should provide even better accuracies in future studies.

Johnson, D. A.↗
NASA NTRS1978

Doppler lidar processing for atmospheric turbulence measurements

A Doppler lidar is described, its processing methods are characterized, and two alternate techniques are considered. The described system uses a CO2 laser transmitting at 10.6 microns and a bank of narrow band filters for the spectrum analysis. Typical results obtained with this system are presented. The two alternate techniques involve computation of the discrete spectrum by use of the discrete Fourier transform. The first technique involves single-pulse processing and incoherent integration, while the second technique performs coherent processing on the train of received pulses.

Polge, R. J.↗
NASA NTRS1979

Turbulence measurements in a rectangular jet

The paper deals with hot-wire measurements in a rectangular incompressible jet issuing into a medium at rest. The flow field of the jet was found to be characterized by the presence of three distinct regions with respect to the mean axial velocity on the center line, referred to as potential core region, two-dimensional type region, and axisymmetric type region. The onset of the second region appears to be at downstream locations where the shear layers from the short dimension of the nozzle meet. Similarly, the center line velocity decay is first of axisymmetric nature at a downstream location where the two shear layers from the long dimension of the nozzle meet. The conditions for the existence of a rectangular jet of an aspect ratio of 16.7 with the laminar tophat profile at the exit are identified.

Krothapalli, A.↗
NASA NTRS1987

A comparison of turbulence measurement methods

An experiment is described in which temperature (density) and velocity are measured separately but simultaneously as functions of time so that it is possible to determine the relationships among velocity, density, and the product of density and velocity. Temperatures were measured with a dual-wire thermocouple probe. Velocity data were supplied by a fringe laser-Doppler anemometer. Signals from thermocouples and the laser were recorded on FM magnetic tape for later processing.

Fralick, Gustave C.↗
NASA NTRS1992

Turbulence measurements of high shear flow fields in a turbomachine seal configuration

The mean velocity and Reynolds stress tensor throughout a whirling annular seal are presented. The data was collected with a three dimensional laser Doppler velocimeter using phase averaging. Two axial flow conditions (Re = 12,000 and 24,000) were studied at one shaft speed (Ta = 6,600). The eccentricity and whirl ratios were 50 and 100 percent, respectively. There is a region of high axial momentum in this region is higher in the low Reynolds number case due to an axial recirculation zone that occurs on the suction side of the rotor at the inlet. The recirculation zone does not occur in the high Reynolds number case. At both Reynolds numbers, there is a recirculation zone on the rotor surface in the pressure side of the inlet. This recirculation zone extends from 20 to 200 degrees rotor zenith in the tangential direction, and is one third of a clearance wide radially. The high Reynolds number recirculation zone is 1.5 mean clearances long, while the low Reynolds number zone extends 2 mean clearances downstream. When compared to previous studies, it is apparent that the tangential momentum is no greater for a seal with whirl than for one without if other parameters are constant. Areas of high tangential momentum occur in the clearance where the axial momentum is low. Average exit plane tangential velocities in the high Reynolds number case are 1.5 times greater than those in the other flow case. These results are in general agreement with predictions made by other investigators.

Morrison, Gerald L.↗
NASA NTRS2002

Measurements of Turbulent Flow Field in Separate Flow Nozzles with Enhanced Mixing Devices - Test Report

As part of the Advanced Subsonic Technology Program, a series of experiments was conducted at NASA Glenn Research Center on the effect of mixing enhancement devices on the aeroacoustic performance of separate flow nozzles. Initial acoustic evaluations of the devices showed that they reduced jet noise significantly, while creating very little thrust loss. The explanation for the improvement required that turbulence measurements, namely single point mean and RMS statistics and two-point spatial correlations, be made to determine the change in the turbulence caused by the mixing enhancement devices that lead to the noise reduction. These measurements were made in the summer of 2000 in a test program called Separate Nozzle Flow Test 2000 (SFNT2K) supported by the Aeropropulsion Research Program at NASA Glenn Research Center. Given the hot high-speed flows representative of a contemporary bypass ratio 5 turbofan engine, unsteady flow field measurements required the use of an optical measurement method. To achieve the spatial correlations, the Particle Image Velocimetry technique was employed, acquiring high-density velocity maps of the flows from which the required statistics could be derived. This was the first successful use of this technique for such flows, and shows the utility of this technique for future experimental programs. The extensive statistics obtained were likewise unique and give great insight into the turbulence which produces noise and how the turbulence can be modified to reduce jet noise.

Bridges, James↗