SEARCH · Search NASA

Results for “UV-Vis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Effect of the Deposition of Vanadium-Oxide on the Photocatalytic Activity of TiO2 Nanotubes and Its Photodiode Performance Interfaced with CH3NH3PbI3 Single Crystal

In this study, we report the influence of vanadium oxide (VO), as a photosensitive component, on the photoactivity of TiO2 nanotubes (TNTs). A series of TNTs of varying tube diameter were synthesized by the anodization of titanium foils at different voltages, while vanadium oxide was deposited on TNTs by wet chemical deposition. An improvement in the optical properties of nanotubes was observed after the deposition of vanadium oxide. An improvement in the optical properties (redshift in UV-Vis spectra) of TNTs and TNT/VO was noted. The photocatalytic activity was improved with increasing tube diameter, while it was weakened after the deposition of VO. Furthermore, photoactivity was investigated in photodiodes based on TNTs or TNT/VO and single crystals of CH3NH3PbI3. The photoelectric measurement revealed that different TNT diameters did not influence the I-V characteristic of the photodiodes, while the deposition of VO improved the photocurrent for smaller TNTs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

New Platinum Complexes from Salen- and Hydroxy-Substituted Salpn-Naphthalene Ligands with CO 2 Reduction Activity

The electrocatalytic reduction of carbon dioxide (CO 2 ) into added-value products is a promising alternative to completing the cycle of atmospheric CO 2 . We report two new platinum complexes—a salen-like naphthalene (PtL1) and a hydroxy-substituted salpn naphthalene (PtL2)—that are capable of activating CO 2 to produce carbon monoxide (CO). The predominant keto tautomer of the non-innocent ligands was determined using DFT calculations and UV-Vis spectroscopy. The PtL2 complex has a CO Faradaic efficiency >40% in the presence of water as a sacrificial proton source at -2.5 V vs. Fc/Fc + . The addition of the hydroxy group in combination with water as a proton source decreased the reduction potential and increased the CO formation tenfold when compared to PtL1.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2022

Synthesis, Crystal and Electronic Structures, Nonlinear Optical Properties, and Magnetic Properties of Two Thiophosphates: KInP 2 S 7 and KCrP 2 S 7

Two thiophosphates, KInP 2 S 7 and KCrP 2 S 7 , were structurally characterized without investigating any optical properties. Herein in this work, KInP 2 S 7 and KCrP 2 S 7 were revisited to investigate their optical and magnetic properties, respectively. Pure polycrystalline samples and crystals of KInP 2 S 7 and KCrP 2 S 7 were grown by high temperature solid state reactions, where mm-sized crystals of KCrP 2 S 7 were collected. KCrP 2 S 7 is isostructural to KInP 2 S 7 , which features a layered structure. KInP 2 S 7 and KCrP 2 S 7 possess close relationship to the layered thiophosphate M 2 P 2 S 6 (M = Fe, Co, Zn, etc.). The bonding pictures of KInP 2 S 7 were studied using the electron localization function (ELF) coupled with crystal orbital Hamilton population (COHP) calculations. The intrinsically distorted [PS 4 ] tetrahedra and [InS 6 ] octahedra are made by strong covalent P-S interactions and ionic In-S interactions, respectively. Electronic structure analysis confirmed that the optical properties of KInP 2 S 7 are mainly contributed to by [PS 4 ] tetrahedra together with small amounts of the contributions coming from [InS 6 ] octahedra. Magnetic measurement on mm-sized crystals of KCrP 2 S 7 verified that there is an antiferromagnetic transition around 21 K, and the Cr atoms are trivalent. KInP 2 S 7 is predicated to be an indirect bandgap semiconductor of 2.38 eV, which is confirmed by the UV-Vis measurement of 2.4(1) eV. KInP 2 S 7 is not a type-I phase-matching material and exhibits moderate second harmonic generation (SHG) response (0.51 × AgGaS 2 , sample of particle size of 100 µm). The laser damage threshold (LDT) of KInP 2 S 7 is very high of 5.2 × AgGaS 2 . Bandgap engineering were undergone to enhance the SHG response of KInP 2 S 7 .

36 MATERIALS SCIENCE↗

DOE OSTI2022

Organo-Nanocups Assist the Formation of Ultra-Small Palladium Nanoparticle Catalysts for Hydrogen Evolution Reaction

Ultra-small palladium nanoparticles were synthesized and applied as catalysts for a hydrogen evolution reaction. The palladium metal precursor was produced via beta-cyclodextrin as organo-nanocup (ONC) capping agent to produce ultra-small nanoparticles used in this study. The produced ~3 nm nanoparticle catalyst was then characterized via X-ray diffraction (XRD), transmission electron microscopy (TEM), ultraviolet-visible spectroscopy (UV-Vis), and Fourier transform infrared spectroscopy (FTIR) to confirm the successful synthesis of ~3 nm palladium nanoparticles. The nanoparticles’ catalytic ability was explored via the hydrolysis reaction of sodium borohydride. The palladium nanoparticle catalyst performed best at 303 K at a pH of 7 with 925 μmol of sodium borohydride having an H 2 generation rate of 1.431 mL min -1 mL cat -1 . The activation energy of the palladium catalyst was calculated to be 58.9 kJ/mol.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Radiation-Induced Oxidation Reactions of 2-Selenouracil in Aqueous Solutions: Comparison with Sulfur Analog of Uracil

One-electron oxidation of 2-selenouracil (2-SeU) by hydroxyl (●OH) and azide (●N3) radicals leads to various primary reactive intermediates. Their optical absorption spectra and kinetic characteristics were studied by pulse radiolysis with UV-vis spectrophotometric and conductivity detection and by the density functional theory (DFT) method. The transient absorption spectra recorded in the reactions of ●OH with 2-SeU are dominated by an absorption band with an λmax = 440 nm, the intensity of which depends on the concentration of 2-SeU and pH. Based on the combination of conductometric and DFT studies, the transient absorption band observed both at low and high concentrations of 2-SeU was assigned to the dimeric 2c-3e Se-Se-bonded radical in neutral form (2●). The dimeric radical (2●) is formed in the reaction of a selenyl-type radical (6●) with 2-SeU, and both radicals are in equilibrium with Keq = 1.3 × 104 M−1 at pH 4 (below the pKa of 2-SeU). Similar equilibrium with Keq = 4.4 × 103 M−1 was determined for pH 10 (above the pKa of 2-SeU), which admittedly involves the same radical (6●) but with a dimeric 2c-3e Se-Se bonded radical in anionic form (2●−). In turn, at the lowest concentration of 2-SeU (0.05 mM) and pH 10, the transient absorption spectrum is dominated by an absorption band with an λmax = 390 nm, which was assigned to the ●OH adduct to the double bond at C5 carbon atom (3●) based on DFT calculations. Similar spectral and kinetic features were also observed during the ●N3-induced oxidation of 2-SeU. In principle, our results mostly revealed similarities in one-electron oxidation pathways of 2-SeU and 2-thiouracil (2-TU). The major difference concerns the stability of dimeric radicals with a 2c-3e chalcogen-chalcogen bond in favor of 2-SeU.

2-selenouracil↗

DOE OSTI2024

Hydrogen Production and Li-Ion Battery Performance with MoS2-SiNWs-SWNTs@ZnONPs Nanocomposites

This study explores the hydrogen generation potential via water-splitting reactions under UV-vis radiation by using a synergistic assembly of ZnO nanoparticles integrated with MoS2, single-walled carbon nanotubes (SWNTs), and crystalline silicon nanowires (SiNWs) to create the MoS2-SiNWs-SWNTs@ZnONPs nanocomposites. A comparative analysis of MoS2 synthesized through chemical and physical exfoliation methods revealed that the chemically exfoliated MoS2 exhibited superior performance, thereby being selected for all subsequent measurements. The nanostructured materials demonstrated exceptional surface characteristics, with specific surface areas exceeding 300 m2 g−1. Notably, the hydrogen production rate achieved by a composite comprising 5% MoS2, 1.7% SiNWs, and 13.3% SWNTs at an 80% ZnONPs base was approximately 3909 µmol h−1g−1 under 500 nm wavelength radiation, marking a significant improvement of over 40-fold relative to pristine ZnONPs. This enhancement underscores the remarkable photocatalytic efficiency of the composites, maintaining high hydrogen production rates above 1500 µmol h−1g−1 even under radiation wavelengths exceeding 600 nm. Furthermore, the potential of these composites for energy storage and conversion applications, specifically within rechargeable lithium-ion batteries, was investigated. Composites, similar to those utilized for hydrogen production but excluding ZnONPs to address its limited theoretical capacity and electrical conductivity, were developed. The focus was on utilizing MoS2, SiNWs, and SWNTs as anode materials for Li-ion batteries. This strategic combination significantly improved the electronic conductivity and mechanical stability of the composite. Specifically, the composite with 56% MoS2, 24% SiNWs, and 20% SWNTs offered remarkable cyclic performance with high specific capacity values, achieving a complete stability of 1000 mA h g−1 after 100 cycles at 1 A g−1. These results illuminate the dual utility of the composites, not only as innovative catalysts for hydrogen production but also as advanced materials for energy storage technologies, showcasing their potential in contributing to sustainable energy solutions.

Chemistry↗

DOE OSTI2022

Degradation in Photovoltaic Encapsulant Transmittance: Results of the Second PVQAT TG5 Artificial Weathering Study

The optical degradation of encapsulants from ultraviolet (UV) radiation has historically resulted in a significant loss in performance throughout the life of a photovoltaic (PV) module. IEC test methods have recently been developed to screen for PV encapsulants prone to loss in optical performance. The present study was performed to benchmark polymeric packaging materials relative to IEC 62788-1-4 (covering the measurement of optical transmittance) and IEC 62788-1-7 (on the durability of transmittance), provide feedback toward improvement of the methods, and develop insight regarding optical degradation. Contemporary materials were examined, including: poly(ethylene-co-vinyl acetate) (EVA), thermoplastic polyolefin (TPO), polyolefin elastomer (POE), and polyvinyl butyral (PVB) encapsulants; a poly(ethene-co-tetrafluoroethene)/poly(ethylene terephthalate) (ETFE/PET) transparent backsheet; and a polystyrene (PS) working reference material. The use of silica-, specialty-, and rolled-glass was also compared in laminated coupons. Specimen size was separately examined from 2.5 cm to 12.5 cm. Weathering was performed with a xenon source, using IEC TS 62788-7-2 methods A2, A3, A4, and A5 (chamber temperature of 55 Degrees C, 65 Degrees C, 75 Degrees C, or 85 Degrees C), respectively. Characterizations were made using a UV-VIS-NIR spectrophotometer (transmittance and reflectance, with and without an integrating sphere), a UV-VIS fluorescence spectrophotometer, a camera, and an optical microscope. Performance was analyzed, including solar weighted transmittance, yellowness index, UV cut-off wavelength, and haze (scattering). Separate Arrhenius analyses were performed to assess retention of transmittance and changes in yellowness index. The activation energy for both characteristics was found to range from 15 kJ?mol-1-80 kJ/mol-1, with an average of 48 kJ/mol-1, similar to the average of 45 kJ/mol-1 identified in the previous international PV Quality Assurance Task Force (PVQAT) Task Group 5 (TG5) study of more traditional encapsulants. The separate degradation modes of discoloration and scattering were distinguished in the encapsulants using a comprehensive spectral characterization. Based on these results, the IEC 62788-1-7 pass/fail criteria of 5% change in transmittance was confirmed to identify a known bad encapsulant.

durability↗

DOE OSTI2024

A Molten Salt Aerosol Spectroscopy Approach to Online Process Monitoring in Molten Salt Reactors

Recent research and development in molten salt reactors (MSRs) has led to many advanced reactor designs, many of which have demonstrations planned in the next decade. However, a significant challenge that must be overcome before liquid fueled MSRs become viable globally is nuclear material accountancy (NMA) and safeguards. Liquid-fueled MSRs are problematic to safeguards because the nuclear material is in the bulk phase, inventories are constantly changing, and there are potentially many outlet pathways that must be monitored, especially in designs with online chemical processing. At the Idaho National Laboratory, we have developed a process monitoring tool to circulate molten salt through a nebulizer and optical cell, where laser-induced breakdown spectroscopy (LIBS) and ultraviolet-visible (UV-VIS) are applied to track the elemental and oxidation states of the constituents in the salt aerosol. This approach has the potential to provide information on the actinides, fission products, and corrosion in the reactor or process. Preliminary testing in aqueous praseodymium chloride (PrCl3) and neodymium chloride (NdCl3) showed good sensitivity detection limits n developed calibration curves. Additional tests and analysis or ongoing in aqueous solutions while equipment is being scaled up for high temperature molten salt testing. Results for continued testing as well as a status of the molten salt design and anticipated commissioning will be presented.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

DOE OSTI2024

Radiation-induced transients on solid and molten Li and K iodides

The study, quantification, and monitoring of iodine in nuclear power generation systems have been paramount due to its environmental and health implications. Thorough speciation and transport studies strengthened the development and deployment of water reactors, which are now required for the new generation of Molten Salt Reactors (MSR), where the fuel and coolant are a complex liquid system of suitable halides. The speciation, radiation-induced chemistry, and transport of iodine (I-127, I-129 and I-131) under extreme conditions of temperature and ionizing radiation are among the challenges for the future implementation of MSR’s. In aqueous systems, the triiodide-iodine-iodide (I3--I2-I-) equilibrium is strongly dependent on the conditions of the medium. In molten iodides and chlorides, the triiodide detection (and its disproportionation) poses challenges due to the extreme conditions of temperature and radiation, but studies have shown a dependence on temperature, absorbed dose and salt composition. Through absorption spectroscopy techniques (diffuse reflectance and high-temperature UV-Vis), as well as resonance (Electron Paramagnetic Resonance) it is possible to identify primary transients induced by ionizing radiation trapped in the solid phase (Solid-state radiolysis), and steady-state main absorption components with a fast-acquisition real-time spectroscopy. The presence of heterogeneous phase (colloids), viscosity changes, and gas evolution are among the observed processes. A specific case of study is speciation in the presence of Ni. A corrosion product with magnetic properties due to unpaired electrons in its electronic structure. Ferromagnetic materials are monitored in solidified salts to identify aggregation and phase separation. Comparative studies of eutectic mixtures of LiI-KI and LiCl-KCl with known addition of dopants will be presented, with a perspective of radiation chemistry and its possible implications in complex systems.

36 - MATERIALS SCIENCE↗

DOE OSTI2025

Challenges in selecting appropriate electrodes for high-temperature molten salt systems

Based on a specific molten salt (e.g., chloride, fluoride, iodide) investigated, different working and reference electrode materials can be selected considering the chemical and thermal stability of the electrochemical cell components. In this talk, the electrode materials and challenges encountered with a spectro-electrochemical setup installed inside a glovebox, and the solutions implemented to address these challenges, specifically for the chloride and iodide molten salts will be presented. For molten chlorides, the fundamental interactions between neodymium chloride (NdCl3) and Nd metal in lithium chloride-potassium chloride eutectic salt were investigated at 773 K. The electrochemical transitions Nd2+,3+/Nd(s) were analyzed using an inert W electrode with cyclic voltammetry and chronoamperometry techniques, coupled with in-situ UV-Vis spectroscopy to elucidate the kinetic pathways of this disproportionation reaction (eq. 1). Nd(s) + NdCl3 = NdCl2 (1) For molten iodides, the challenges related to working electrode selectivity and present spectro-electrochemical results obtained from cyclic voltammetry measurements conducted at 673 K will be discussed.

36 - MATERIALS SCIENCE↗

DOE OSTI2025

In Situ Spectroscopic Monitoring of MSR Molten Salt and Off-Gas Systems

A significant challenge that must be overcome before commercialization of molten salt reactors is tracking special nuclear material (SNM) through the reactor and subsystems such as fuel chemical processing and off-gas systems. In recent years, several approaches have been explored to track SNM, fission products, and corrosion products in these different subsystems. One such approach is to employ laser and optical spectroscopy to measure the atomic and molecular signals of MSR salts. The advantages of these approaches are that they typically are non-intrusive and offer the capability of process monitoring while still providing low uncertainties. At the Idaho National Laboratory, spectroscopy approaches such as laser-induced breakdown spectroscopy (LIBS) and ultraviolet-visible (UV-Vis) spectroscopy have been utilized to investigate molten salts in an aerosol (LiCl, KCl, RbCl2, NdCl3, and PrCl3) and vapor phases (MgCl5, NdCl5, and ZrCl4) with success. Testing to date has yielded qualitative information on all the above species and quantitative data and analytical figures of merit for species in the vapor phases. These findings, including results from ongoing testing, as well as the experimental conditions and potential applications will be presented.

98 - NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL↗

DOE OSTI2025

Why are Lead Iodide‐Based Perovskite Precursor Inks Yellow?

A challenge faced by metal halide perovskite (MHP) photovoltaics is scaling up solution deposition processes to realize rapid and inexpensive manufacturing. The challenge lies in completely understanding and controlling solution speciation, nucleation, and self-assembly of iodoplumbate complexes during solvent evaporation as the liquid transforms into gels and solids. An accurate description of solution species, at all points in the transformation, is a prerequisite to design robust and reliable processes. Here, in this study, the common assumption that initial monoplumbate solution species typically invoked (e.g., [PbI 6 ] 4− ) are certainly not the origin of optical absorbance at >400 nm wavelengths is disproved, as are many large particles of common “intermediate” iodoplumbate phases with face- or edge-sharing connectivity. Instead, a new perspective is offered, involving (partially) corner-sharing iodo(poly)plumbates (>1 Pb 2+ per complex) that experience highly dynamic chemical environments. It is outlined how the MHP field would benefit by elucidating these phenomena. Future work is required to determine the size and kinetic behavior of polyplumbate species, and contextualize these findings in relation to broader trends in materials chemistry beyond MHPs. Ultimately, a complete explanation for the solution speciation, optical absorbance signatures, and the color of MHP precursor inks remains an open challenge to the community.

14 SOLAR ENERGY↗

DOE OSTI2023

Self-diagnosis of model suitability for continuous measurements of stream-dissolved organic carbon derived from in situ UV–visible spectroscopy

Application of high-frequency monitoring of dissolved organic carbon (DOC) is difficult in instances where training datasets are challenging to develop (e.g., remote locations) and the relationship between optical features and DOC concentration changes due to environmental or landscape shifts (e.g., climate or land-use change). We developed and compared three partial least squares (PLS) models using in situ water level measurements, conductivity, and UV–Vis spectral attenuation to predict DOC. Two site-specific models were developed using data from a hillslope-dominated forest or a low-relief wetland-pond-dominated stream catchment. The third model, using data from both sites, exhibited the best performance (DOC range = 4–15.5 mg C L −1 , mean = 8.38 mg C L −1 , training RMSE = 0.34 mg C L −1 , internal validation RMSE = 0.50 mg C L −1 , external validation RMSE = 2.43 mg C L −1 ). We further demonstrate using PLS model statistics to monitor performance and elucidate when and how models should be updated. These statistics, Hotelling's T 2 and squared prediction errors, are useful consistency checks for the predictions made and detect underlying inconsistencies that, if undetected, can reduce the robustness of DOC prediction. For example, via the T 2 statistic, we identified the summer–autumn transition as a period when DOC composition differed from what was represented in the training dataset. We also determined that elevated SUVA 254 values contributed to the overall bias observed in predictions made during the subsequent year as part of the external validation. This enabled the application of a bias correction that reduced the RMSE from 2.43 to 0.89 mg C L −1 . The method presented here could be applied to future monitoring programs enabling model updates to monitor DOC fluxes accurately from optical datasets (e.g., attenuance or fluorescence) in the face of developing datasets in remote locations or environmental change. In conclusion, implementation of this approach may also identify possible regime shifts or landscape and hydrologic change associated with climate and other environmental changes relevant to terrestrial to aquatic fluxes.

UV-VIS spectroscopy↗

DOE OSTI2024

Comparison of effects from gamma, e-beam and X-ray radiation on multilayer polymer films used in biopharmaceutical devices by chemometric treatment of spectroscopic data

The present study investigated the effects of gamma-ray, electron beam, and X-ray radiation on polymers in EVA/EVOH/EVA multilayer films. Spectroscopic methods, including FTIR and UV–Vis, were employed in conjunction with chemometric treatments such as PCA, SIMPLISMA treatments, and PLS models. The feasibility of dose prediction on multilayer film, given a known dose, is attainable across various irradiation technologies. Both gamma ray and X-ray exhibit comparable effects on the multilayer film, and it is feasible to anticipate the dose released on the film by utilizing UV–Vis spectra or infrared spectra for gamma ray or X-ray of a predetermined dose.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2023

Machine Learning Models for Predicting Molecular UV–Vis Spectra with Quantum Mechanical Properties

Accurate understanding of Ultraviolet–visible (UV–Vis) spectra is critical for highthroughput design of compounds for drug discovery. Experimentally determining UV–Vis spectra can become expensive when dealing with a large quantity of novel molecules. This provides us an opportunity to drive computational advances in molecular property predictions using quantum mechanics and machine learning. In this work, we use both Quantum Mechanically (QM) predicted and measured UV–Vis spectra as input to modify four different machine learning architectures: UVvis-SchNet, UVvis- DTNN, UVvis-Transformer, and UVvis-MPNN. Here we find that the UVvis-MPNN model outperforms the other models when using optimized 3D coordinates and QM predicted spectra as input features. This model has the highest performance for predicting UVVisible spectra with a training RMSE of 0.06 and validation RMSE of 0.08.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Water-Soluble Copper(I) Hydroxide Catalyst and Its Formation in Ligand-Free Suzuki–Miyaura Cross-Coupling Reactions

Copper has emerged as an alternative metal for metal-catalyzed cross-coupling reactions due to its low cost, readily availability, and low toxicity. Here this article reports a water-soluble active molecular catalyst and its formation in the ligand-free Suzuki–Miyaura (SM) cross-coupling reactions with copper iodide as the precatalyst in aqueous solutions. The SM coupling is homogeneous in nature, and the molecular catalyst is Cu(OH) in its singlet electronic state as identified by experimental and computational UV–vis absorption spectroscopy. The Cu(OH) catalyst is generated through the leaching of oval-shaped Cu 2 O nanoparticles, which are characterized with X-ray Auger electron spectroscopy, X-ray absorption spectroscopy, and transmission electron microscopy. The soluble Cu(OH) species is stable for at least 4 weeks under ambient conditions.

cross-coupling↗

DOE OSTI2025

Tuning the Molecular Structure and Reaction Mechanism of Olefin Metathesis by Model Bilayered Supported MoO x /AlO x /SiO 2 Catalysts

The molecular structure and activity of supported MoO x olefin metathesis catalysts are heavily impacted by the choice of catalyst support. In this study, surface modification of the SiO 2 support with AlO x and selective anchoring of the MoO x on the surface AlO x sites were used to tune the structure, activation, and reactivity of the resulting surface MoO x sites. Extensive in situ molecular characterization, chemical probe studies, and density functional theory (DFT) calculations reveal that the enhanced activity of the supported MoO x /AlO x /SiO 2 catalyst over the MoO x / SiO 2 catalyst is associated with more favorable activation and kinetics of surface MoO x anchored at AlO x sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

The Stability of Nd Hydroxyl Complexes at Near Neutral to Alkaline pH from 25 to 75 °C: Implications for Monazite Solubility in Hydrothermal Aqueous Fluids

Speciation of rare earth elements (REE) in aqueous fluids controls their mobilization during fluid-rock interaction. Thermodynamic modeling provides important insights into the factors controlling REE mobility and fractionation in aqueous fluids, in which aqueous REE hydroxyl complexes are particularly important across a broad pH range. However, the stability of these REE hydroxyl complexes remains poorly determined due to limited experimental data above ambient temperature. In this work, UV–vis spectrophotometry experiments were conducted to determine the cumulative hydrolysis constants for neodymium (Nd) from 25 to 75 °C in near-neutral to alkaline solutions. The color indicator m -cresol purple was used to determine in situ pH. Alkaline NaOH-bearing aqueous solutions were doped with varying initial Nd concentrations (0 to ∼0.155 mmol/kg), which resulted in the release of protons (H + ) and pH decrease during hydrolysis of Nd 3+ according to Nd 3+ + n H 2 O = Nd(OH) n 3– n + H + . The average OH – ligand number coordinated to Nd 3+ was found to increase from 1.0 to 1.6 at 25 °C and from 1.2 to 2.8 at 75 °C over a pH range from 6.3 to 9.0. The measured speciation shows an increased predominance of Nd(OH) 3 0 over the Nd(OH) 2 + and Nd(OH) 2+ species with increased temperature and pH. The increasing cumulative formation constants (log*β° n , n = 1 to 3) retrieved from 25 to 75 °C differ by 0.1 to 1.9 logarithmic units in comparison to existing thermodynamic databases. These updated thermodynamic data have important implications for geochemical modeling of the speciation of Nd hydroxyl complexes and the solubility of monazite as a function of pH.

58 GEOSCIENCES↗