SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Simulation studies of navigational and operational problems for variable sweep and fixed delta-wing supersonic transports under air traffic control procedures
Longitudinal aerodynamic characteristics of hypersonic lifting body spacecraft with variable sweep wings
A wind-tunnel investigation has been made of the longitudinal aerodynamic characteristics and jet-interference effects of a model of a jet V/STOL variable-sweep fighter airplane that employs four direct-lift engines which swing out from the fuselage and two lift-cruise engines located in the rear part of the fuselage. Data were obtained with two wing areas for various forward speeds and power conditions in the transition speed range. The data are presented without analysis or discussion.
A wind-tunnel investigation has been made of the effects of ground proximity on the longitudinal and lateral-directional aerodynamic characteristics and jet-interference effects of a model of a jet V/STOL variable-sweep fighter airplane that employs four direct-lift engines which swing out from the fuselage ahead of the wing and two lift-cruise engines located in the rear part of the fuselage. Data were obtained through a range of angles of attack and sideslip at simulated speeds from hover through transition at various heights of the model above a moving-belt ground plane. Power-off data and power-on data at several power conditions are presented. The data are presented without analysis or discussion.
The aerodynamic characteristics of a six-engine (four lift, two lift-cruise) lift-engine model obtained in the Ames 40- by 80-foot wind tunnel are presented. The model was an approximate one-half scale representation of a lift-engine VTOL fighter aircraft with a variable-sweep wing. The four lift-engines were housed in the aft fuselage with the inlets located above the wing. Longitudinal and lateral-directional force and moment data are presented for a range of exhaust gas momentum ratios (thrust coefficients). Wind tunnel forward speed was varied from 0 to 140 knots corresponding to a maximum Reynolds number of 6.7 million. The data are presented without analysis.
A wind-tunnel technique which makes use of a dynamically scaled aeroelastic model to predict full-scale airplane buffet loads during buffet boundary penetration is evaluated. A 1/8-scale flutter model of a fighter airplane with remotely controllable variable-sweep wings and trimming surfaces was used for the evaluation. The model was flown on a cable-mount system which permitted high lift forces comparable to those in maneuvering flight. Bending moments and accelerations due to buffet were measured on the flutter model and compared with those measured on the full-scale airplane in an independent flight buffet research study. It is concluded that the technique can provide valuable information on airplane buffet load characteristics not available from any other source except flight test.
Summarized are the aerodynamic center, alpha and q- aeroelastic effects on fighter-type aircraft in the 18,700 N gross range. The results indicate that with proper tailoring of planform (fixed or variable sweep), stiffner and elastic axis location it is possible to minimize trim requirements between selected extreme conditions. The inertial effects were found to be small for this class of aircraft.
An initial design study of high-transonic-speed transport aircraft has been completed. Five different design concepts were developed. These included fixed swept wing, variable-sweep wing, delta wing, double-fuselage yawed-wing, and single-fuselage yawed-wing aircraft. The boomless supersonic design objectives of range=5560 Km (3000 nmi), payload-18 143 kg (40 000lb), Mach=1.2, and FAR Part 36 aircraft noise levels were achieved by the single-fuselage yawed-wing configuration with a gross weight of 211 828 Kg (467 000 lb). A noise level of 15 EPNdB below FAR Part 36 requirements was obtained with a gross weight increase to 226 796 Kg (500 000 lb). Although wing aeroelastic divergence was a primary design consideration for the yawed-wing concepts, the graphite-epoxy wings of this study were designed by critical gust and maneuver loads rather than by divergence requirements. The transonic nacelle drag is shown to be very sensitive to the nacelle installation. A six-degree-of-freedom dynamic stability analysis indicated that the control coordination and stability augmentation system would require more development than for a symmetrical airplane but is entirely feasible. A three-phase development plan is recommended to establish the full potential of the yawed-wing concept.
An initial design study of high-transonic-speed transport aircraft has been completed. Five different design concepts were developed. These included fixed swept wing, variable-sweep wing, delta wing, double-fuselage yawed-wing, and single-fuselage yawed-wing aircraft. The boomless supersonic design objectives of range = 5560 km (3000 nmi), payload = 18,143 kg (40,000 lb), Mach = 1.2, and FAR Part 36 aircraft noise levels were achieved by the single-fuselage yawed-wing configuration with a gross weight of 211,828 kg (467,000 lb). A noise level of 15 EPNdB below FAR Part 36 requirements was obtained with a gross weight increase to 226,796 kg (500,000 lb). The off-design subsonic range capability for this configuration exceeded the Mach 1.2 design range by more than 20%. Although wing aeroelastic divergence was a primary design consideration for the yawed-wing concepts, the graphite-epoxy wings of this study were designed by critical gust and maneuver loads rather than by divergence requirements. The transonic nacelle drag is shown to be very sensitive to the nacelle installation. A six-degree-of-freedom dynamic stability analysis indicated that the control coordination and stability augmentation system would require more development than for a symmetrical airplane but is entirely feasible. A three-plane development plan is recommended to establish the full potential of the yawed-wing concept.
A comparative evaluation of fixed-geometry and variable-sweep wing designs, a fixed delta wing, and oblique wings with a single body or two bodies suggests that an oblique wing is preferable in a transonic transport aircraft in terms of gross weight, fuel consumption, and aircraft noise, and also shows an acceptable aeroelastic stability. Further studies are, however, needed to develop the full potential of the oblique-wing concept, including its economic implications.
This paper is concerned with the estimation of stability and control parameters of a high performance fighter aircraft from data obtained from high angle of attack flight. The estimation process utilizes a maximum likelihood algorithm derived for the case of a nonlinear aerodynamic force and moment model. The aircraft used was a high speed variable sweep heavy weight fighter with twin vertical tails. Comparisons of results from the nonlinear analysis are made with linear theory and wind tunnel results when available.
Oblique-wing twin- and single-fuselage transonic transport models were wind tunnel tested and showed superior aerodynamic efficiency to that of fixed-swept-wing, variable-sweep-wing, and delta-wing configurations similarly tested. The oblique-wing airplane had the smallest gross weight and lowest fuel consumption; it could achieve lower noise levels than swept- and delta-wing aircraft by engine-nacelle treatment; and it was aeroelastically less stable than a sweptback wing but more stable than a swept-forward wing. Graphite-epoxy met stability requirements without additional stiffening, whereas aluminum needed some additional stiffness. Further studies are called for to develop the full potential of the oblique-wing concept.
Fluctuating pressures and forces that cause aircraft buffeting have been measured on a semispan rigid-wing model of a typical variable-sweep fighter-type aircraft at transonic speeds. The rms spectral and spatial correlation characteristics of wing fluctuating pressures, fluctuating pressure summations, and structural responses are presented and discussed for a Mach number of 0.85, wing sweep angles of 26 and 72 deg, and angles of attack up to 12 deg. The fluctuating pressure characteristics beneath wing shock waves and leading-edge vortices and in regions of attached and separated flows are presented. Results indicate that: (1) the mean and fluctuating static pressure characteristics are related; (2) a circulation oscillation exists for attached flow conditions below buffet onset; and (3) a significant coupling exists between the wing shock-wave oscillation and the wing first torsional mode when shock-induced separation is present.
The feasibility of the RF gauging mode, counting technique was demonstrated for gauging liquid hydrogen and liquid oxygen under all attitude conditions. With LH2, it was also demonstrated under dynamic fluid conditions, in which the fluid assumes ever changing positions within the tank, that the RF gauging technique on the average provides a very good indication of mass. It is significant that the distribution of the mode count data at each fill level during dynamic LH2 and LOX orientation testing does approach a statistical normal distribution. Multiple space-diversity probes provide better coupling to the resonant modes than utilization of a single probe element. The variable sweep rate generator technique provides a more uniform mode versus time distribution for processing.
The slow landing speeds (30 mph, 65 mph) and light wing loading required for safety in the early days of aviation are shown to be irrelevant to safe landings of propeller-driven aircraft, while increases in wing loading and landing speed have been accompanied by improved safety records. This is attributed to length of runway and time available for approach maneuvers, plus immunity to wind gusts and turbulence conferred by higher wing loadings. Aerodynamical and mechanical aspects of safe landing are discussed, with no mention of instruments. Fuel savings achievable through high aspect ratio, variable sweep angle, and supercritical airfoils are also considered.
Supercritical airfoils and their applications to wings for various types of aircraft are studied. The various wings discussed were designed for a subsonic jet transport with increased speed, a variable sweep fighter with greater transonic maneuverability, a high subsonic speed STOL jet transport with improved low speed characteristics, and a subsonic jet transport with substantially improved aerodynamic efficiency. Results of wind tunnel and flight demonstration investigations are described. Also discussed are refinements of the transonic area rule concept and methods for reducing the aerodynamic interference between engine nacelles and wings at high subsonic speeds.
Studies of transport aircraft designed for boom-free supersonic flight show the variable sweep oblique wing to be the most efficient configuration for flight at low supersonic speeds. Use of this concept leads to a configuration that is lighter, quieter, and more fuel efficient than symmetric aircraft designed for the same mission. Aerodynamic structural, weight, aeroelastic and flight control studies show the oblique wing concept to be technically feasible. Investigations are reported for wing planform and thickness, pivot design and weight estimation, engine cycle (bypass ratio), and climb, descent and reserve fuel. Results are incorporated into a final configuration. Performance, weight, and balance characteristics are evaluated. Flight control requirements are reviewed, and areas in which further research is needed are identified.
The longitudinal stability characteristics of a complete model equipped with a variable sweep wings at angles of sweepback of 45 deg, 30 deg, 15 deg, and 0 deg investigated. Various wing modifications and an extern 1 flap arrangement designed to minimize the shift in neutral point accompanying the change in sweep angle were studied. The results indicate that stability at the stall was obtained at a sweep angle of 15 deg without recourse to stall control devices. The basic neutral point movement accompanying the change in sweep angle from 45 deg to 15 deg amounted to 56 percent of the mean aerodynamic chord (at zero sweep angle) and the most effective modification investigated only reduced this change to 47 percent of the chord. It appears, therefore, that for designs in which the fuselage is the major load carrying element some relative movement between the wing and center of gravity will be required to assure satisfactory stability at all sweep angles.