Search NASA⌕ Search

SEARCH · Search NASA

Results for “VELOCITY ERROR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

CFD Modelling of Bore Erosion in Two-Stage Light Gas Guns

A well-validated quasi-one-dimensional computational fluid dynamics (CFD) code for the analysis of the internal ballistics of two-stage light gas guns is modified to explicitly calculate the ablation of steel from the gun bore and the incorporation of the ablated wall material into the hydrogen working cas. The modified code is used to model 45 shots made with the NASA Ames 0.5 inch light gas gun over an extremely wide variety of gun operating conditions. Good agreement is found between the experimental and theoretical piston velocities (maximum errors of +/-2% to +/-6%) and maximum powder pressures (maximum errors of +/-10% with good igniters). Overall, the agreement between the experimental and numerically calculated gun erosion values (within a factor of 2) was judged to be reasonably good, considering the complexity of the processes modelled. Experimental muzzle velocities agree very well (maximum errors of 0.5-0.7 km/sec) with theoretical muzzle velocities calculated with loading of the hydrogen gas with the ablated barrel wall material. Comparison of results for pump tube volumes of 100%, 60% and 40% of an initial benchmark value show that, at the higher muzzle velocities, operation at 40% pump tube volume produces much lower hydrogen loading and gun erosion and substantially lower maximum pressures in the gun. Large muzzle velocity gains (2.4-5.4 km/sec) are predicted upon driving the gun harder (that is, upon using, higher powder loads and/or lower hydrogen fill pressures) when hydrogen loading is neglected; much smaller muzzle velocity gains (1.1-2.2 km/sec) are predicted when hydrogen loading is taken into account. These smaller predicted velocity gains agree well with those achieved in practice. CFD snapshots of the hydrogen mass fraction, density and pressure of the in-bore medium are presented for a very erosive shot.

Bogdanoff, D. W.↗
DOE OSTI2022

Image-domain DAS 3D VSP elastic transmission tomography

SUMMARY Full-wavefield elastic imaging of active-source seismic data acquired by downhole receivers commonly offers higher-resolution subsurface images in the vicinity of a borehole compared to conventional surface seismic data sets, which can lack higher-frequency wavefield components due to longer travel paths and increased attenuation. An increasingly used approach for downhole acquisition is vertical seismic profiling (VSP), which has become more attractive when coupled with distributed acoustic sensing (DAS) using optical fibres installed in wells. The main difficulty for generating high-quality images with full-wavefield imaging tools for DAS VSP data, though, is the need for an accurate velocity model. To build plausible velocity models using active-source DAS VSP data, we adopt a 3-D image-domain elastic transmission tomography technique, originally developed for surface-recorded passive (microseismic) data, by exchanging the source and receiver positions (i.e. reciprocity) to mimic a passive-seismic surface monitoring scenario. The inversion approach exploits various images for each source constructed through time-reverse imaging (TRI) of downgoing P- and S-wave first-arrival waveforms. The TRI process uses the kinetic term of the (extended) PS energy imaging condition that exhibits sufficient sensitivity to velocity model errors. The method automatically updates the P- and S-wave velocity models to optimize image focusing via adjoint-state inversion. We illustrate the efficacy of the adopted elastic inversion technique using an active-source DAS 3-D VSP field data set acquired in the North Slope of Alaska. The numerical experiments demonstrate that the inverted elastic velocity models can be further used in full-wavefield acoustic/elastic imaging algorithms to obtain accurate subsurface images.

Oren, Can (ORCID:000000019534265X)↗
DOE OSTI2023

Modeling a Miniature Voitenko-Like Explosively-Driven Shock Tube Using FLAG

Using the FLAG hydrocode, hypervelocity plasma jets observed in miniature explosively–driven shock tube experiments have been modeled with a relative error in velocity of less than 5% (a reduction from previous attempts which yielded errors of 37%). This suggests that FLAG may be well-suited to model HE systems involving the acceleration of gases through complex crack systems in HE devices: A phenomenon not accurately captured using current modeling capabilities. The Eulerian hydrocode model presented here leverages AMR to reduce computational cost and, importantly, it was found that mesh resolution and model geometry each significantly affected the average jet velocity. The model and the results are detailed here together with comments on challenges during its development and avenues for future work.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1985

Correcting for particle counting bias error in turbulent flow

An ideal seeding device is proposed generating particles that exactly follow the flow out are still a major source of error, i.e., with a particle counting bias wherein the probability of measuring velocity is a function of velocity. The error in the measured mean can be as much as 25%. Many schemes have been put forward to correct for this error, but there is not universal agreement as to the acceptability of any one method. In particular it is sometimes difficult to know if the assumptions required in the analysis are fulfilled by any particular flow measurement system. To check various correction mechanisms in an ideal way and to gain some insight into how to correct with the fewest initial assumptions, a computer simulation is constructed to simulate laser anemometer measurements in a turbulent flow. That simulator and the results of its use are discussed.

Edwards, R. V.↗
NASA NTRS2018

Production of Negative Hydrogen Ions Within the MMS Fast Plasma Investigation Due to Solar Wind Bombardment

The particle data delivered by the Fast Plasma Investigation instrument aboard National Aeronautics and Space Administration's Magnetospheric Multiscale (MMS) mission allow for exceptionally high-resolution examination of the electron and ion phase space in the near-Earth plasma environment. It is necessary to identify populations which originate from instrumental effects. Using Fast Plasma Investigation's Dual Electron Spectrometers, we isolate a high-energy (approximately kiloelectron volt) beam, present while the spacecraft are in the solar wind, which exhibits an azimuthal drift with period associated with the spacecraft spin. We show that this population is consistent with negative hydrogen ions H− generated by a double charge exchange interaction between the incident solar wind H+ ions and the metallic surfaces within the instrument. This interaction is likely to occur at the deflector plates close to the instrument aperture. The H− density is shown to be approximately 0.2-0.4% of the solar wind ion density, and the energy of the negative ion population is shown to be 70% of the incident solar wind energy. These negative ions may introduce errors in electron velocity moments on the order of 0.2-0.4% of the solar wind velocity and significantly higher errors in the electron temperature.

Magnetospheric Multiscale↗
DOE OSTI2020

An analysis of the spatio-temporal resolution of the immersed boundary method with direct forcing

The immersed boundary method (IBM) with direct forcing is very popular in the simulation of rigid particulate flows. In the IBM, an interaction force is introduced at the interface between fluid and particle in order to approximate the no-slip boundary condition. The interaction force is calculated through dividing the velocity difference (or error) between fluid and particle at the interface by the time step. Here, a dynamic equation for the velocity difference is derived. Additionally, analyses on the dynamic equation provide a few new findings: (i) The interaction force is the solution of a least-squares error problem, with the direct implication that the Lagrangian marker distribution has no effect on the large scale flow structure once the distribution of Lagrangian markers become saturated along the interface (i.e., each marker remains properly correlated with all its neighbors); (ii) The Lagrangian volume-weight is a relaxation factor to control how fast the velocity error decays to the ideal value of zero; (iii) The optimal choice of the Lagrangian volume-weight is the largest value permissible by a stability condition. A comprehensive convergence analysis with regard to the spatial and temporal resolution is presented for the velocity error and also for the shear-stress and surface pressure. In three simple canonical problems, it is analytically and numerically shown that the IBM results converge to the theoretical solutions obtained with precise imposition of no-slip and no-penetration boundary conditions. It is observed that it is not necessary to match the Lagrangian marker volume-weight to that of the local Eulerian cell volume and in fact this matching leads to lower than optimal computational efficiency. However, it is found that extremely high Eulerian grid resolution and small time step have to be used to obtain high precision simulation results. Especially, the time step should be inversely proportional to the particle Reynolds number for low Reynolds number flows. For high frequency oscillation problems, the grid size needs to be reduced by a factor of the square root of the frequency, and the time step to be reduced by a factor of the frequency. The theoretical findings here can be used to alleviate the technical difficulties in simulating non-spherical particles by not requiring the Lagrangian marker distribution to match the Eulerian grids and also in the implementation of IBM on non-uniform Eulerian grids. The present work also provides simple practical guidance on the choice of temporal and spatial resolution so as to control the simulation error a priori.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1998

Preston Probe Calibrations at High Reynolds Number

The overall goal of the research effort is to study the performance of two Preston probes designed by NASA Langley Research Center across an unprecedented range of Reynolds number (based on friction velocity and probe diameter), and perform an accurate calibration over the same Reynolds number range. Using the Superpipe facility in Princeton, two rounds of experiments were performed. In each round of experiments for each Reynolds number, the pressure gradient, static pressure from the Preston probes and the total pressure from the Preston probes were measured. In the first round, 3 Preston probes having outer diameters of 0.058 inches, 0.083 inches and 0.203 inches were tested over a large range of pipe Reynolds numbers. Two data reduction methods were employed: first, the static pressure measured on the Preston probe was used to calculate P (modified Preston probe configuration), and secondly, the static pressure measured at the reference pressure tap was used to calculate P (un-modified Preston probe configuration). For both methods, the static pressure was adjusted to correspond with the static pressure at the Preston probe tip using the pressure gradient. The measurements for Preston probes with diameters of 0.058 inches, and 0.083 inches respectively were performed in the test pipe before it was polished a second time. Therefore, the measurements at high pipe Reynolds numbers may have been affected by roughness. In the second round of experiments the 0.058 inches and 0.083 inches diameter, un-modified probes were tested after the pipe was polished and prepared to ensure that the surface was smooth. The average velocity was estimated by assuming that the connection between the centerline velocity and the average velocity was known, and by using a Pitot tube to measure the centerline velocity. A preliminary error estimate suggests that it is possible to introduce a 1% to 2% error in estimating the average velocity using this approach. The evidence on the errors attending the second data set is somewhat circumstantial, and the measurements have not been repeated using a better approach, it seems probable that the correlation given applies to un-modified Preston probes over the range 6.4 less than x* less than 11.3.

Smits, Alexander J.↗
NASA NTRS1992

The Laser Atmospheric Wind Sounder (LAWS) Preliminary Error Budget and Performance Estimate

The Laser Atmospheric Wind Sounder (LAWS) study phase has resulted in a preliminary error budget and an estimate of the instrument performance. This paper will present the line-of-sight (LOS) Velocity Measurement Error Budget, the instrument Boresight Error Budget, and the predicted signal-to-noise ratio (SNR) performance. The measurement requirements and a preliminary design for the LAWS instrument are presented in a companion paper.

Kenyon, David L.↗
DOE OSTI2025

DESI peculiar velocity survey – Fundamental Plane

The Dark Energy Spectroscopic Instrument (DESI) peculiar velocity survey aims to measure the peculiar velocities of early- and late-type galaxies within the DESI footprint using both the Fundamental Plane and optical Tully–Fisher relations. Direct measurements of peculiar velocities can significantly improve constraints on the growth rate of structure, reducing uncertainty by a factor of approximately 2.5 at redshift 0.1 compared to the DESI Bright Galaxy Survey’s redshift space distortion measurements alone. We assess the quality of stellar velocity dispersion measurements from DESI spectroscopic data. These measurements, along with photometric data from the Legacy Survey, establish the Fundamental Plane relation and determine distances and peculiar velocities of early-type galaxies. During survey validation, we obtain spectra for 6698 unique early-type galaxies, up to a photometric redshift of 0.15. 64 per cent of observed galaxies (4267) have relative velocity dispersion errors below 10 per cent. This percentage increases to 75 per cent if we restrict our sample to galaxies with spectroscopic redshifts below 0.1. We use the measured central velocity dispersion, along with photometry from the DESI Legacy Imaging Surveys, to fit the Fundamental Plane parameters using a 3D Gaussian maximum likelihood algorithm that accounts for measurement uncertainties and selection cuts. In addition, we conduct zero-point calibration using the absolute distance measurements to the Coma cluster, leading to a value of the Hubble constant, H 0 = 76.05 ± 0.35 (statistical) ±0.49 (systematic Fundamental Plane) ±4.86 (statistical due to calibration) km s –1 Mpc –1 ⁠. This H 0 value is within 2σ of Planck cosmic microwave background results and within 1σ of other low-redshift distance indicator-based measurements.

cosmological parameters↗
NASA NTRS1986

A lateral guidance algorithm to reduce the post-aerobraking burn requirements for a lift-modulated orbital transfer vehicle

A lateral guidance algorithm which controls the location of the line of intersection between the actual and desired orbital planes (the hinge line) is developed for the aerobraking phase of a lift-modulated orbital transfer vehicle. The on-board targeting algorithm associated with this lateral guidance algorithm is simple and concise which is very desirable since computation time and space are limited on an on-board flight computer. A variational equation which describes the movement of the hinge line is derived. Simple relationships between the plane error, the desired hinge line position, the position out-of-plane error, and the velocity out-of-plane error are found. A computer simulation is developed to test the lateral guidance algorithm for a variety of operating conditions. The algorithm does reduce the total burn magnitude needed to achieve the desired orbit by allowing the plane correction and perigee-raising burn to be combined in a single maneuver. The algorithm performs well under vacuum perigee dispersions, pot-hole density disturbance, and thick atmospheres. The results for many different operating conditions are presented.

Herman, G. C.↗
NASA NTRS2000

Calibration of a Spacecraft Gyro Quadruplet

This work presents a new approach to gyro calibration where, in addition to being used for computing attitude that is needed in the calibration process, the gyro outputs are also used as measurements in a Kalman filter. Gyro calibration as well as calibration of other instruments occurs in two steps. In the first step, the instrument error parameters are estimated. During the second stage, those errors are continuously removed from the gyro readings. In the classical approach to gyro calibration, the gyro outputs are used to maintain or compute body orientation rather than being used as measurements in the context of filtering. In inertial navigation, for example, gyro errors cause erroneous computation of velocity and position, and then when the latter are compared to measured velocity and position, a great portion of the computed velocity and position errors can be determined. The latter errors are then fed into a Kalman filter (KF) that uses the INS error model to infer on the gyro errors. Similarly, when applying the classical approach to spacecraft (SC) altitude determination, the gyro outputs are used to compute the attitude and then attitude measurements are used to determine the attitude errors, which again using a KF, indicates what the gyro errors are. In the approach adopted in this work the gyro outputs are used as angular rate measurements and are compared to estimated angular rate measurements. However, this approach requires the knowledge of the angular rate. In the past, the estimated angular rate was computed in a rather simplistic way assuming that the rate was constant. In the present work, the estimated angular rate is derived using a KF whose input can be any kind of attitude measurement, therefore the angular rate experienced by the SC can be continuously changing, and yet a good estimate of the rate, necessary for calibration, can be obtained.

Harman, Richard R.↗
NASA NTRS1982

A comparison of turbulence intensity measurements using a laser velocimeter and a hot wire in a low speed jet flow

The study involves a simultaneous measurement with both instruments along radial scans at two axial locations in the jet exiting from the turbulent pipe and an axial scan at the 75-percent radial location in the jet from the convergent nozzle. The results suggest that, within the limits of flow stationarity, both instruments yield measurements in good agreement, + or - 0.8-percent in turbulence intensity, below a turbulence intensity (the ensemble standard deviation divided by the local mean velocity) of 20 percent. From turbulence intensities of 20 percent to a maximum of 75 percent, the measurements exhibit the same trends; for reasons discussed here, however, the comparisons are not of the quality as those below 20 percent. It is found that correcting the turbulence intensity data for velocity bias errors increases the results by an average of 2 percent in turbulence intensity above the hot wire results and the uncorrected laser velocimeter data. The results are seen as calling into question the validity of using the velocity bias correction and time average techniques for turbulence intensity measurements.

Meyers, J. F.↗
DOE OSTI2022

Experimental characterization of extreme temperature granular flows for solar thermal energy transport and storage

High-temperature, dense granular flows along an inclined plane were considered for solar thermal energy transport and storage with sintered bauxite particles. A series of experiments was performed for particle inlet temperatures of ~ 200, 400, 600, and 800 °C to understand the mechanisms of granular flows at extreme temperatures. Mass flow rates were measured using a load cell and free-surface velocities were measured and computed using particle image velocimetry. Surface temperatures were measured using infrared cameras. A significant decrease in steady-state particle mass flow rate was observed with increasing temperature due to changing flow properties. A decrease in bulk particle free-surface velocities was observed at higher temperatures. Free-surface velocity measurement error between experiments were within 20% of the average. The particle surface temperatures decreased from inlet to outlet with larger gradients at higher temperatures observed due to increasing convection and radiative heat losses. Here, a decrease in temperature was observed along the side walls due to a decrease in particle velocities.

14 SOLAR ENERGY↗
NASA NTRS1986

Radial-velocity measures and the existence of astrophysical binaries in late-type dwarf stars

Radial velocities with errors of 1-2 km/s are presented based on CCD scans obtained with the Kitt Peak National Observatory coude feed telescope between 1982 and 1985 of 48 dK-M stars that lack Balmer emission. Comparison with Gliese's (1969) values shows only two stars to be spectroscopic binary candidates with small velocity amplitudes. No evidence for any short period (less than 10 days) binaries is found, supporting the conclusions of Young et al. (1986) that there are no astrophysical binaries among these chromosherically inactive dM stars.

Bopp, B. W.↗
DOE OSTI2022

An improved pressure drop correlation for modeling localized effects in a pebble bed reactor

Advances in the development of pebble bed reactors (PBRs) has created a desire for accurate and cost-effective simulation tools for design scoping studies and safety analysis. The current state-of-the-art for these simulations is the use of porous media models, although these models rely on correlations to capture the effects of flow features that are not explicitly modeled. One of the areas where correlation accuracy is currently lacking is in the near-wall region of the bed. In this region, the presence of the wall causes the pebbles to pack more orderly, drastically changing the geometry and flow behavior in this region. This work presents a new generalized pressure drop correlation for PBRs based on the KTA equation. A high-to-low methodology is applied, where large eddy simulation (LES) is performed on two beds of 1568 and 1700 pebbles to generate a high-fidelity dataset. The flow fields are then averaged in time and separated into concentric rings of 0.05 D peb width. Average porosity, velocity, and pressure drop are extracted for each ring and the friction and form losses are calculated. The Reynolds number range for this study is 625–10,000, and thus the form losses are dominant over the friction losses. The form losses across the rings are investigated, and a correction term for the form loss calculation is determined and applied to the KTA equation to drastically improve the capability of modeling localized porosity effects in a porous media code. Finally, the improved correlation reduces near-wall velocity prediction error from over 50% with the KTA correlation to around 5%. Agreement in pressure drop prediction between LES and porous media simulations is also improved.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Dark matter density profiles in dwarf galaxies: linking Jeans modelling systematics and observation

ABSTRACT The distribution of dark matter in dwarf galaxies can have important implications on our understanding of galaxy formation as well as the particle physics properties of dark matter. However, accurately characterizing the dark matter content of dwarf galaxies is challenging due to limited data and complex dynamics that are difficult to accurately model. In this paper, we apply spherical Jeans modelling to simulated stellar kinematic data of spherical, isotropic dwarf galaxies with the goal of identifying the future observational directions that can improve the accuracy of the inferred dark matter distributions in the Milky Way dwarf galaxies. We explore how the dark matter inference is affected by the location and number of observed stars as well as the line-of-sight velocity measurement errors. We use mock observation to demonstrate the difficulty in constraining the inner core/cusp of the dark matter distribution with data sets of fewer than 10 000 stars. We also demonstrate the need for additional measurements to make robust estimates of the expected dark matter annihilation signal strength. For the purpose of deriving robust indirect detection constraints, we identify Ursa Major II, Ursa Minor, and Draco as the systems that would most benefit from additional stars being observed.

79 ASTRONOMY AND ASTROPHYSICS↗