Search NASA⌕ Search

SEARCH · Search NASA

Results for “VIBRATION PROTECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Structural, vibrational, and electronic topological transitions of Bi 1.5 Sb 0.5 Te 1.8 Se 1.2 under pressure

Topological insulators have been the subject of intense research interest due to their unique surface states that are topologically protected against scattering or defects. However, the relationship between the crystal structure and topological insulator state remains to be clarified. Here, we show the effects of hydrostatic pressure on the structural, vibrational, and topological properties of the topological insulator Bi 1.5 Sb 0.5 Te 1.8 Se 1.2 up to 45 GPa using X-ray diffraction and Raman spectroscopy in a diamond anvil cell, together with first-principles theoretical calculations. Two pressure-induced structural phase transitions were observed: from ambient rhombohedral R3¡m phase to a monoclinic C2/m phase at ~13 GPa, and to a disordered I4/mmm phase at ~22 GPa. In addition, the alloy undergoes several electronic transitions within the R3¯m phase: indirect to direct bulk band gap transition at ~5.8 GPa, bulk gap closing with an appearance of Dirac semimetal (DSM) state at ~8.2 GPa, and to a trivial semimetal state at ~12.1 GPa. Anomalies in c/a ratio and Raman full width at half maximum that coincide with the DSM phase suggest the contribution of electron-phonon coupling to the transition. Here, compared to binary end members Bi 2 Te 3 , Bi 2 Se 3 , and Sb 2 Te 3 , the structural phase transition and anomaly were observed at higher pressures in Bi 1.5 Sb 0.5 Te 1.8 Se 1.2 . These results suggest that the topological transitions are precursors to the structural phase transitions.

42 ENGINEERING↗

Loads and aeroelasticity division research and technology accomplishments for FY 1982 and plans for FY 1983

Accomplishments of the past year and plans for the coming year are highlighted as they relate to five year plans and the objectives of the following technical areas: aerothermal loads; multidisciplinary analysis and optimization; unsteady aerodynamics; and configuration aeroelasticity. Areas of interest include thermal protection system concepts, active control, nonlinear aeroelastic analysis, aircraft aeroelasticity, and rotorcraft aeroelasticity and vibrations.

Gardner, J. E.↗

Document Monitor

The charters of Freedom Monitoring System will periodically assess the physical condition of the U.S. Constitution, Declaration of Independence and Bill of Rights. Although protected in helium filled glass cases, the documents are subject to damage from light vibration and humidity. The photometer is a CCD detector used as the electronic film for the camera system's scanning camera which mechanically scans the document line by line and acquires a series of images, each representing a one square inch portion of the document. Perkin-Elmer Corporation's photometer is capable of detecting changes in contrast, shape or other indicators of degradation with 5 to 10 times the sensitivity of the human eye. A Vicom image processing computer receives the data from the photometer stores it and manipulates it, allowing comparison of electronic images over time to detect changes.

Source record↗

Periodic Material-Based Seismic Base Isolators for Small Modular Reactors

Important structures such as nuclear power plants should experience very little vibrations in order to maintain the safety of the nuclear facilities during seismic events. Protection of these structures by seismic isolators requires the isolators to provide seismic isolation irrespective of the direction of excitations and to develop a stable response without rocking. Conventional seismic isolation systems, however, can only fulfill partial requirements for the seismic protection. This study adopts the principle of periodic materials for seismic isolation. These materials exhibit unique properties of frequency band gaps, where incoming waves with frequencies falling inside the frequency band gaps are forbidden. The new isolation systems, known as periodic foundations, function both as a structural foundation to support the gravitational weight of the superstructure and also as a seismic isolator. The isolation mechanism, hypothetically, can easily fulfill all the requirements for seismic protection of the critical facilities. This study focuses on the design of one-dimensional (1D) and three-dimensional (3D) periodic foundations for seismic isolation of small modular reactor (SMR) buildings. The theoretical study was first conducted to reveal the fundamental behavior of periodic foundations. Then global sensitivity analysis was utilized to study the effect of design parameters on the frequency band gaps. In addition, simple straight-forward design equations based on the sensitivity analysis are proposed for the design of periodic foundations. Utilizing the proposed equations, prototypes of 1D and 3D periodic foundations were designed to isolate an SMR building. Scaled models were fabricated and experimentally tested to validate the hypothesis and design. The periodic foundation structural systems were tested under various input waves, including seismic waves, in the horizontal and vertical directions and the torsional mode. The shake table test results show that the periodic foundations can reduce the acceleration response of the SMR building up to 90% in the horizontal direction and the torsional mode. As much as a 40% response reduction in the vertical direction is also observed. Moreover, the periodic foundation-isolated structure exhibited stable response with negligible rocking on the structure. This study proved the capability of periodic foundations to enhance the seismic safety of critical structures.

42 ENGINEERING↗

Operando FTIR Studies of Electrolyte Solution Structures and Dynamics at Electrode-Electrolyte Interfaces

The well-stabilized electrode-electrolyte interface (EEI) is critical to battery performance and safety, thus understanding the electrolyte solution structures (e.g., ion solvation and ionic association) and dynamics within EEI is an important area of study. Unfortunately, due to the sensitive nature of the electrodes, ex-situ characterization methods are limited and challenging to interpret as chemical and structural changes occur upon deconstructing the cell. In this work, we present operando characterization of near-surface electrolyte solution structures and dynamics by ATR-FTIR spectroscopy during battery cycling. We studied two selected model electrodes, a lithium nickel manganese cobalt oxide (NMC) or a planar silicon (Si), in a standard Gen2 electrolyte of 1.2 M LiPF6 in ethylene carbonate (EC):ethyl methyl carbonate (EMC) (3:7 wt%). In the former case, the composite cathode on aluminum foil is placed face-down on an ATR crystal. A ring of lithium metal serves as the counter/reference electrode and no separator is required. In the latter case, a lightly doped p-type silicon wafer is phosphorous-doped at the surface to increase the conductivity of the sample without compromising infrared transparency. The ATR crystal is then pressed on the back of the silicon with a minimal air gap to ensure sufficient optical contact between the two materials. The front of wafer is then placed in a modified coin-type cell geometry with a minimal electrolyte, a separator, and a lithium metal counter/reference electrode. In both experiments, we analyze the electrolyte solution structures within the EEI and find similar patterns as a function of potential. Firstly, we find that EMC decomposes faster than EC -suggesting that EMC plays a greater role in the electrochemical reactions on the electrode surface (e.g., formation of a protective layer to prevent further electrolyte decomposition). Secondly, we monitor the increase/decrease of the vibrational absorption peaks attributed to carbonates coordinated with Li+ ions relative to the decrease/increase of their uncoordinated counterparts, as expected when changing the local concentration of Li+ ions near the electrode surface during deintercalation/intercalation into the electrode. Finally, we observe that the features assigned to the Li+-PF6 -/-solvent molecules contact ion pair relative to the uncoordinated PF6 - anion. These observations give important information regarding the electrolyte solution structures and dynamics near the electrode surfaces. We look forward to applying these techniques to additional lithiumion battery systems with different cathode or anode materials and beyond lithium-ion systems to characterize surface chemistry/evolution (on-going research) and solution structures/dynamics (in particular, (de)solvation behaviors) within the EEI, which can be a bottleneck to efficient ion transfer from the electrolyte to the electrode.

14 SOLAR ENERGY↗

Design of a Transport System for the PIP-II HB650 Cryomodule

The PIP-II Project at FNAL requires the assembly of 3 high-beta 650MHz cryomodules at STFC Daresbury (DL) in the UK. These modules must be safely transported from DL to FNAL in the USA. Previous experience with cryomodule transport was leveraged at both labs to design a transport system to protect the cryomodules during transit. Requirements for the system included mitigation of shocks, drops, and vibrations, and acting as a lifting fixture. It is comprised of a tessellated steel frame which encompasses the module with a wire rope isolator arrangement which the module mounts to. The frame was designed to withstand the weight of the 12.5 tonne cryomodule in various load cases. Details of shock and vibration profiles were obtained from MIL-STD-810H and were used to guide the sizing of the isolators. The frame and the isolation system were analysed via FEA using the shock and vibration profiles as an input. The transport system was found to be suitable for the given isolation, frame stiffness, and lifting code requirements. The frame has been fabricated and successfully load tested at FNAL. It will now be road tested with a dummy cryomodule before undergoing a trial run to DL.

43 PARTICLE ACCELERATORS↗

Passive Vibration Isolator For Experiments

Passive isolator reduces natural vibrational frequency of platform to less than 1 Hz - well below frequencies of vibration induced by human activity. Biological, crystal-growth, and other experiments mounted on platform protected against disturbances by technicians working in vicinity. Designed for use in microgravitational environment of spacecraft. Modified version designed for use on Earth by including components counteracting steady normal Earth gravitation. Consumes no electrical power, simple, and inexpensive.

Naumann, Robert J.↗

Exploration Exercise System (EES) Development

Exploration class missions will be required to have an exercise device that is lightweight, has a small footprint, and is capable of providing enough physical stimulus and exercise variability to be an effective countermeasure against muscle and bone loss that results from the microgravity environment. Exploration exercise device prototypes should be evaluated on the ground and in-orbit for feasibility of use in microgravity for long and short duration exploration missions and efficacy of the device to maintain multi-system health and performance. The European Enhanced Exploration Exercise Device (E4D) was selected as the exploration prototype device to be evaluated on ISS for efficacy and feasibility of use as a single multi-modality device for the exercise system for exploration missions. This effort supports the continued development, testing, and verification of E4D hardware and software, internal NASA integration (Human Health and Performance, ISS Vehicle Office, Engineering, and Flight Operations), and external integration across NASA, ESA, and the Danish Aerospace Company (DAC). Providing a feasibility and acceptability assessment from a physiological efficacy and hardware durability standpoint are critical for informing use and risk associated with use on exploration missions. Clearly defined objectives from end users, stakeholders, and Subject Matter Experts (SMEs) will be tested by crewmembers during acute use sessions and long duration use of the exercise device while on ISS. This effort will include a flight study where crewmembers will be asked to exercise using only the E4D during the duration of their mission and participate in a battery of physiological testing to evaluate the efficacy. Hardware is scheduled to launch in FY25 followed by 2 years of operational use after activation and checkout. A final recommendation will be provided to the Artemis program on acceptability of the device for exploration missions. The E4D needs a vibration isolation stabilization (VIS) system that serves as a platform for the exercise hardware to protect the vehicle from loads imparted during exercise. Exploration forward VIS systems will need to protect the vehicle and provide sufficient stabilization for the exerciser during performance of all critical exercises. These enabling capabilities need to be achieved within exploration vehicle power, thermal, mass, and volume limitations.

Kent Lawrence Kalogera↗

Analysis of Launch Vehicle Liftoff Debris: Historical Perspective from Space Shuttle and Application to Artemis I

Human exploration-class launch vehicles are inherently prone to debris due to the extreme environments generated during pre-launch operations, liftoff, and flight. The use of cryogenic propellants often requires thermal protection system (TPS) coatings, typically foam, to maintain the propellant conditions in the tank and prevent an accumulation ice on the external surface of the vehicle. Some ice growth is to be expected at umbilical interfaces, vents, flanges, or brackets where it is difficult to apply TPS. This ice may come loose at any time due to wind on the launch pad, structural vibration and acoustics after rocket ignition, or aerodynamic forces during flight. This phenomena is especially apparent on vehicles with no TPS, such as the Saturn V rockets used in the Apollo Program, see Figure 1. During propellant tanking, the thermal contraction of the underlying substrate may generate cracks in the TPS (Figure 1). Chunks of TPS can release due to the expansion of ingested gas from cryopumping or from aerodynamic forces if the crack creates an offset surface. Most foams will also have a certain amount of “popcorning” where small pieces of foam will pop off during flight because of the differential between the static surface pressure and the pressure of the gas trapped in the foam cell structure. There are a number of other coating or closeout materials that may be shed from the vehicle and become debris. During pre-launch operations and liftoff, the vehicle may also be exposed to debris originating from the launch pad or ground support equipment. This debris is separate from foreign object debris, or FOD, which is not intended to be present and is strictly controlled through operations and maintenance procedures. In this case, debris is generated from hardware and materials that are necessary for launch and are subject to the intense vibration, acoustics, and direct plume impingement of the launch environment. Examples include ice from umbilicals, tape and tie wraps that protect cables, and rust or corrosion from the launch platform. While NASA has historically been aware of debris as a potential issue that could cause a failure resulting in loss of mission, loss of vehicle, or loss of crew, the likelihood and severity of that risk was not always well understood or given sufficient weight in program and flight decisions. After the Space Shuttle Columbia accident (STS-107), the investigation found that foam TPS debris shed from the external tank was the proximate cause of the damage to the orbiter wing. Six previous observations of debris released from the foam ramp that covered the bipod connecting the forward end of the orbiter to the external tank resulted in minor changes or were determined to be accepted flight risks. Two occurrences of bipod ramp foam loss were not identified until the STS-107 investigation. Despite the damage inflicted by these debris strikes, the Shuttle Program Requirements Control Board deemed the vehicle safe to fly. During the Return to Flight effort following the Columbia disaster, NASA Engineering developed a process for the assessment of debris transport, impact, and damage tolerance to support independent assessments of risk by NASA Safety and Mission Assurance (S&MA). Under this system, each element (vehicle or ground system) defines a catalog of all expected debris based on launch history, component testing, or analysis. Debris transport analysis (DTA) is conducted using the debris catalog characteristics and potential flow transport mechanisms (e.g., vehicle aerodynamics, gravity, wind, plume-driven). The predicted debris impact locations and velocities are provided to the hardware owners, who use available test data and analysis to determine whether each component can withstand the impacts. In cases where the element hardware may be severely damaged or fail, the options are to mitigate the debris source through some change in design or operation, or to work with S&MA to try to characterize the probability of the impact and damage for program risk acceptance. Because of the differences in debris characteristics and transport, the DTA has been divided between the Liftoff and Ascent regimes. The development and application of Liftoff DTA methodology from the Shuttle Program to the current Artemis Program is the subject of this paper. Liftoff DTA covers the time from the start of pre-launch operations at the launch pad, up until the vehicle clears the launch tower and there is no longer any interaction with ground systems. Debris transport during this period is broadly classified as either gravity, wind, and plume-entrained (GWPE) or plume driven (PD). GWPE debris is generally lower speed, travelling in a forward-to-aft direction. PD transport includes flow features from the rocket ignition transient, as well as plume impingement and recirculation that occur as the vehicle lifts off the launch platform. In these cases, the debris typically moves in an aft-to-forward direction at higher speeds. The applicable transport mechanisms must be considered for each piece of debris depending on the material, and release location and time. For example, rust or metallic debris from the tower could fall (GWPE) and impact the vehicle before landing on the launch platform deck where it could be also be transported by plume impingement (PD). However, falling ice (GWPE) from an umbilical is unlikely to survive impact with the vehicle or launch platform and be available for PD transport. Modeling of debris transport is accomplished using a set of DTA tools which simulate debris trajectories subject to a reference frame acceleration (i.e., gravity) and aerodynamic drag. Where the trajectory encounters a solid surface, the debris is allowed to rebound with a specified coefficient of restitution. The drag is calculated by interpolating the fluid state at each point in the debris trajectory from high-fidelity computational fluid dynamics (CFD) simulations of the launch vehicle and pad. The CFD data may either be static (steady state or time averaged), typically for GWPE transport, or dynamic (time-accurate) for PD flow features like the ignition transient. Examples of the CFD flow field solutions for the Space Launch System (SLS) rocket and launch pad are shown in Figure 2. Typical SLS debris trajectory predictions from DTA are illustrated in Figure 3. The final version of this paper will include a more detailed examination of the Liftoff DTA process developed during the Shuttle Program, and how it has been augmented and applied to the SLS rocket under the Artemis Program. Comparisons with debris observations from the Artemis I launch will demonstrate validation of the tools and methodology.

Debris↗

Quench conditioning device. Vibrational quench conditioning

Recently a new type of device, capacitor-based, aiming to eliminate or reduce superconducting magnet training was developed and tested at FNAL. I’ll review its main characteristics and principles of operation, make relevant comparisons and conclusions. Separately, I’ll discuss somewhat similar concepts based on induced vibrations in magnets, but I’ll extend this topic to cover both training reduction and quench protection. Those will be discussed at conceptual level, arguing about feasibility of such an approach and the need for more focused research on the topic, including simulations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Cabin fuselage structural design with engine installation and control system

Design requirements for the cabin, cabin system, flight controls, engine installation, and wing-fuselage interface that provide adequate interior volume for occupant seating, cabin ingress and egress, and safety are presented. The fuselage structure must be sufficient to meet the loadings specified in the appropriate sections of Federal Aviation Regulation Part 23. The critical structure must provide a safe life of 10(exp 6) load cycles and 10,000 operational mission cycles. The cabin seating and controls must provide adjustment to account for various pilot physiques and to aid in maintenance and operation of the aircraft. Seats and doors shall not bind or lockup under normal operation. Cabin systems such as heating and ventilation, electrical, lighting, intercom, and avionics must be included in the design. The control system will consist of ailerons, elevator, and rudders. The system must provide required deflections with a combination of push rods, bell cranks, pulleys, and linkages. The system will be free from slack and provide smooth operation without binding. Environmental considerations include variations in temperature and atmospheric pressure, protection against sand, dust, rain, humidity, ice, snow, salt/fog atmosphere, wind and gusts, and shock and vibration. The following design goals were set to meet the requirements of the statement of work: safety, performance, manufacturing and cost. To prevent the engine from penetrating the passenger area in the event of a crash was the primary safety concern. Weight and the fuselage aerodynamics were the primary performance concerns. Commonality and ease of manufacturing were major considerations to reduce cost.

Balakrishnan, Tanapaal↗

Additively Manufactured Tamper Evident Container

Los Alamos National Laboratory has developed a revolutionary and reliable new tamper evident container (TEC) to monitor and protect the health, security, and distribution of high-value assets, technological advancements, products, materials and more that are critical to the operations of businesses and government organizations. Unlike traditional tamper evident seals, the entire TEC serves as a seal, with encrypted on-board electronics able to continuously monitor and log structural health data including but not limited to force, temperature, pressure, humidity, orientation, radiation, acceleration, or vibration as needed. Analog and encrypted digital boards safely stored inside the TEC permanently record the complete integrity history of the protected items and have the ability to alert the TEC owners or take immediate defensive actions should a disruptive or tamper event take place.

36 MATERIALS SCIENCE↗

Environmental protection requirements for scout/shuttle auxiliary stages

The requirements for enabling the Scout upper stages to endure the expected temperature, mechanical shock, acoustical and mechanical vibration environments during a specified shuttle mission were determined. The study consisted of: determining a shuttle mission trajectory for a 545 kilogram (1200 pound) Scout payload; compilation of shuttle environmental conditions; determining of Scout upper stages environments in shuttle missions; compilation of Scout upper stages environmental qualification criteria and comparison to shuttle mission expected environments; and recommendations for enabling Scout upper stages to endure the exptected shuttle mission environments.

Qualls, G. L.↗

Flight Controller Software Protects Lightweight Flexible Aircraft

Lightweight flexible aircraft may be the future of aviation, but a major problem is their susceptibility to flutter-uncontrollable vibrations that can destroy wings. Armstrong Flight Research Center awarded SBIR funding to Minneapolis, Minnesota-based MUSYN Inc. to develop software that helps program flight controllers to suppress flutter. The technology is now available for aircraft manufacturers and other industries that use equipment with automated controls.

Source record↗

Protective Package for a Gamma-Ray Detector

Package for germanium gamma-ray detector protects semiconductor crystal from contamination, allows it to operate at high voltages, and isolates from shock and vibration. Package seals detector from its surroundings, whether in atmosphere or in vacuum of space. Main parts of package made of aluminum. Cover sealed to base by soft aluminum ring.

Fong, M.↗

Vibration and flutter analysis of reusable surface insulation panels

A study has been conducted of the aeroelastic behavior of heat shield panels for the thermal protection system of the space shuttle. Questions of structural and aerodynamic modeling are considered along with the analysis of a single isotropic tile and an isotropic main substructure. Representative flutter results are presented, taking into account a rigid and a flexible metallic substructure.

Dowell, E. H.↗

New technology for recovering residual metals from nonmetallic fractions of waste printed circuit boards

Highlights: • Vibrated gas-solid fluidized bed can recycle residual metals from WPCBs. • Glass fibers have bad effect on vibrated gas-solid fluidized bed segregation. • Each size fraction has its own optimum segregation parameters. • Fine size fraction has the worst segregation efficiency. - Abstract: Recycling of waste printed circuit boards is important for environmental protection and sustainable resource utilization. Corona electrostatic separation has been widely used to recycle metals from waste printed circuit boards, but it has poor separation efficiency for finer sized fractions. In this study, a new process of vibrated gas-solid fluidized bed was used to recycle residual metals from nonmetallic fractions, which were treated using the corona electrostatic separation technology. The effects of three main parameters, i.e., vibration frequency, superficial air flow velocity, and fluidizing time on gravity segregation, were investigated using a vibrating gas-solid fluidized bed. Each size fraction had its own optimum parameters. Corresponding to their optimal segregation performance, the products from each experiment were analyzed using an X-ray fluorescence (XRF) and a scanning electron microscope (SEM) equipped with an energy dispersive spectrometer (EDS). From the results, it can be seen that the metal recoveries of −1 + 0.5 mm, −0.5 + 0.25 mm, and −0.25 mm size fractions were 86.39%, 82.22% and 76.63%, respectively. After separation, each metal content in the −1 + 0.5 or −0.5 + 0.25 mm size fraction reduced to 1% or less, while the Fe and Cu contents are up to 2.57% and 1.50%, respectively, in the −0.25 mm size fraction. Images of the nonmetallic fractions with a size of −0.25 mm indicated that a considerable amount of clavate glass fibers existed in these nonmetallic fractions, which may explain why fine particles had the poorest segregation performance.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Pre-strain effect on frequency-based impact energy dissipation through a silicone foam pad for shock mitigation [Pre-strain effect on the frequency response of shock mitigation through a silicone foam pad]

Silicone foams have been used in a variety of applications from gaskets to cushioning pads over a wide range of environments. Particularly, silicone foams are used as a shock mitigation material for shock and vibration applications. Understanding the shock mitigation response, particularly in the frequency domain, is critical for optimal designs to protect internal devices and components more effectively and efficiently. The silicone foams may be subjected to pre-strains during the assembly process which may consequently influence the frequency response with respect to shock mitigation performance. A Kolsky compression bar was modified with pre-compression capabilities to characterize the shock mitigation response of silicone foam in the frequency domain to determine the effect of pre-strain. Lastly, a silicone sample was also intentionally subjected to repeated pre-strain and dynamic loadings to explore the effect of repeated loading on the frequency response of shock mitigation.

36 MATERIALS SCIENCE↗