Search NASA⌕ Search

SEARCH · Search NASA

Results for “WEST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Developing high performance RF heating scenarios on the WEST tokamak

High power experiments, up to 9.2 MW with LHCD and ICRH, have been carried out in the full tungsten tokamak WEST. Quasi non inductive discharges have been achieved allowing to extend the plasma duration to 53s with stationary conditions in particular with respect to tungsten contamination. Transitions in H mode are obtained lasting up to 4s with weak energy increment at the power crossing the separatrix is close to the threshold. Hot L mode plasmas (Te(0)>3keV) with a confinement time following the ITER L96 scaling are routinely obtained. The weak aspect ratio dependence of this scaling law is confirmed. Tungsten accumulation is generally not an operational issue on WEST. Difficulty of burning through tungsten can prevent from accessing to a hot core plasma in the ramp-up phase or can lead to rapid collapse of the central temperature when radiation is enhanced by a slight decrease of the temperature. Apart few pulses post-boronization, the plasma radiation is rather high (Prad/Ptot~50%) and is dominated by tungsten. This fraction does not vary as the RF power is ramped up and is quite similar in ICRH and/or LHCD heated plasmas. An estimate of the contribution of the RF antennas to the plasma contamination in tungsten is given.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Distribution Development for Residual Inventory at the New York West Valley Site - 20400

The New York State Energy Research and Development Authority (NYSERDA) is the owner of the Western New York Nuclear Service Center (WNYNSC), a 1,351 ha site located approximately 48 km south of Buffalo, New York. In 1962, Nuclear Fuel Services, Inc. (NFS) entered into Agreements with the Atomic Energy Commission and New York State to construct the first commercial reprocessing plant of nuclear fuel in the United States. NFS, a private company, built and operated the spent fuel reprocessing plant and waste disposal facilities, processing 640 Mg of spent nuclear fuel from 1966 to 1972 under an Atomic Energy Commission license. Nuclear fuel reprocessing operations ended in 1972 and never reopened, leaving behind radioactive and chemical wastes. Operations led to contamination in a number of facilities and locations. Some of that contamination has migrated from waste disposal zones to other layers, formations, and features on and off the WNYNSC. Phase I decommissioning activities are ongoing and involve the removal of a number of areas and structures that have been associated with contamination. The purpose of this work is to outline the approach for characterizing contamination not associated with disposed wastes, contaminated structures, or specific releases. In this work, the term, residual radiological activity, is used to describe environmental contamination that exists subsequent to the completion of Phase I decommissioning activities, that is not associated with disposed wastes, contaminated structures, or specific releases. Contamination from the Site was quantified relative to data that characterize the concentrations of radionuclides that exist in background. Background concentrations are those present in the area but having no influence from Site related activities. The existence of residual radiological activity that is elevated relative to background has the potential to contribute to future risks to human health and the environment. As a consequence, the residual inventory information is used to inform the West Valley Probabilistic Performance Assessment (PPA) model to characterize potential future risks to human health and the environment. The centralized West Valley Data Management System (DMS) was the source of information for the data assembled in this analysis. The DMS is a fairly large compilation consisting of thousands of records from investigation studies, with sample dates ranging from 1990 to present. Samples from monitoring wells, boreholes, geoprobe studies, surface water, surface soils, storm water outfalls, ventilation stack filters, plant and animal tissues, and more are included in the DMS. Results are typically reported in units of activity per unit volume. For the purpose of the analyses presented here, all results were converted into consistent units of pCi per unit volume. Since 1990, data have been collected from various locations across the WNYNSC at different times with varying frequency over the course of several decades. As a consequence, a number of potential issues can arise with respect to the assembly of a dataset that is deemed adequate for the characterization of residual radiological activity. These issues were assessed and resolved to the extent possible through careful consideration of the properties of the distributions. The intent was to use data which characterize the current state of the Site. Radionuclides can be designated to one of several groups depending on their origin. In this work the groups considered were 1) Naturally Occurring Radioactive Material (NORM), 2) fallout, and 3) Other (including power plant, medical research, etc). This grouping is a useful construct with respect to the interpretation of fixed laboratory results. For example, NORM radionuclides that exist within a decay chain should have approximately equivalent distributions of concentrations if they are representative of background conditions. Insights such as these can be used as a check to identify sample results that need to be further investigated or omitted due to issues associated with reported results from fixed laboratory analyses. This type of analysis provided a foundation for the assessment of the adequacy of sample results for use in subsequent components of an assessment. The general process for the assessment of residual radiological contamination at the Site consists of a sequence of several steps. First, for each analyte, several statistical tests were performed to assess the weight of evidence against the null hypothesis that the mean of the distribution of concentrations was equal to zero. If the mean of the distribution of concentrations for a given radionuclide was not found to be greater than zero, then it was removed from consideration as a component of the residual radiological contamination. If there was significant evidence to reject the hypothesis of the mean being equal to zero, the second step was to compare the distribution of the data from the Site to that of the corresponding background. A suite of tests was used to compare the distributions of the site and background data. The results of these tests were collectively used to determine if site data are elevated relative to background. The third step was to develop distributions using a Bayesian framework to characterize the distribution of mean of the increment present above background for each of the radionuclides. The Bayesian model implemented allowed for the comparison of site-specific records to background concentrations to better approximate contamination attributed to the Site. A final screening step was employed for radionuclides that exceed background. This screening step compared 95% upper confidence limits (UCLs) from the increment distribution developed in the previous step to the risk screening levels. This approach yields a list of analytes that were determined to be elevated relative to background.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

West Valley Demonstration Project (WVDP) Annual Site Environmental Report (ASER) for Calendar Year 2023

The report, prepared for the U.S. Department of Energy West Valley Demonstration Project office (DOE-WVDP), summarizes the environmental protection program at the WVDP for calendar year (CY) 2023. Monitoring and surveillance of the facilities used by the DOE are conducted to verify protection of public health and safety and the environment. The report is a key component of DOE’s effort to keep the public informed of environmental conditions at the WVDP. The quality assurance protocols applied to the environmental monitoring program ensure the validity and accuracy of the monitoring data. In addition to demonstrating compliance with environmental laws, regulations, and directives, evaluation of data collected in 2023 continued to indicate that WVDP activities pose no threat to public health or safety, or to the environment.

Record of Decision↗
DOE OSTI2023

Evaluation of an open forecasting challenge to assess skill of West Nile virus neuroinvasive disease prediction

Abstract Background West Nile virus (WNV) is the leading cause of mosquito-borne illness in the continental USA. WNV occurrence has high spatiotemporal variation, and current approaches to targeted control of the virus are limited, making forecasting a public health priority. However, little research has been done to compare strengths and weaknesses of WNV disease forecasting approaches on the national scale. We used forecasts submitted to the 2020 WNV Forecasting Challenge, an open challenge organized by the Centers for Disease Control and Prevention, to assess the status of WNV neuroinvasive disease (WNND) prediction and identify avenues for improvement. Methods We performed a multi-model comparative assessment of probabilistic forecasts submitted by 15 teams for annual WNND cases in US counties for 2020 and assessed forecast accuracy, calibration, and discriminatory power. In the evaluation, we included forecasts produced by comparison models of varying complexity as benchmarks of forecast performance. We also used regression analysis to identify modeling approaches and contextual factors that were associated with forecast skill. Results Simple models based on historical WNND cases generally scored better than more complex models and combined higher discriminatory power with better calibration of uncertainty. Forecast skill improved across updated forecast submissions submitted during the 2020 season. Among models using additional data, inclusion of climate or human demographic data was associated with higher skill, while inclusion of mosquito or land use data was associated with lower skill. We also identified population size, extreme minimum winter temperature, and interannual variation in WNND cases as county-level characteristics associated with variation in forecast skill. Conclusions Historical WNND cases were strong predictors of future cases with minimal increase in skill achieved by models that included other factors. Although opportunities might exist to specifically improve predictions for areas with large populations and low or high winter temperatures, areas with high case-count variability are intrinsically more difficult to predict. Also, the prediction of outbreaks, which are outliers relative to typical case numbers, remains difficult. Further improvements to prediction could be obtained with improved calibration of forecast uncertainty and access to real-time data streams (e.g. current weather and preliminary human cases). Graphical Abstract

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

West Valley Demonstration Project (WVDP) Annual Site Environmental Report (ASER) for Calendar Year 2021

The report, prepared for the U.S. Department of Energy West Valley Demonstration Project office (DOE-WVDP), summarizes the environmental protection program at the WVDP for calendar year (CY) 2021. Monitoring and surveillance of the facilities used by the DOE are conducted to verify protection of public health and safety and the environment. The report is a key component of DOE’s effort to keep the public informed of environmental conditions at the WVDP. The quality assurance protocols applied to the environmental monitoring program ensure the validity and accuracy of the monitoring data. In addition to demonstrating compliance with environmental laws, regulations, and directives, evaluation of data collected in 2021 continued to indicate that WVDP activities pose no threat to public health or safety, or to the environment.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

West Valley Demonstration Project (WVDP) (Annual Site Environmental Report (ASER), Calendar Year 2022)

The report, prepared for the U.S. Department of Energy West Valley Demonstration Project office (DOE-WVDP), summarizes the environmental protection program at the WVDP for calendar year (CY) 2022. Monitoring and surveillance of the facilities used by the DOE are conducted to verify protection of public health and safety and the environment. The report is a key component of DOE’s effort to keep the public informed of environmental conditions at the WVDP. The quality assurance protocols applied to the environmental monitoring program ensure the validity and accuracy of the monitoring data. In addition to demonstrating compliance with environmental laws, regulations, and directives, evaluation of data collected in 2022 continued to indicate that WVDP activities pose no threat to public health or safety, or to the environment.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Exploring Climate-Disease Connections in Geopolitical Versus Ecological Regions: The Case of West Nile Virus in the United States

Many infectious disease forecasting models in the United States (US) are built with data partitioned into geopolitical regions centered on human activity as opposed to regions defined by natural ecosystems; although useful for data collection and intervention, this has the potential to mask biological relationships between the environment and disease. We explored this concept by analyzing the correlations between climate and West Nile virus (WNV) case data aggregated to geopolitical and ecological regions. We compared correlations between minimum, maximum, and mean annual temperature; precipitation; and annual WNV neuroinvasive disease (WNND) case data from 2005 to 2019 when partitioned into (a) climate regions defined by the National Oceanic and Atmospheric Administration (NOAA) and (b) Level I ecoregions defined by the Environmental Protection Agency (EPA). We found that correlations between climate and WNND in NOAA climate regions and EPA ecoregions were often contradictory in both direction and magnitude, with EPA ecoregions more often supporting previously established biological hypotheses and environmental dynamics underlying vector-borne disease transmission. Using ecological regions to examine the relationships between climate and disease cases can enhance the predictive power of forecasts at various scales, motivating a conceptual shift in large-scale analyses from geopolitical frameworks to more ecologically meaningful regions.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Structure of an RNA G-quadruplex from the West Nile virus genome

Potential G-quadruplex sites have been identified in the genomes of DNA and RNA viruses and proposed as regulatory elements. The genus Orthoflavivirus contains arthropod-transmitted, positive-sense, single-stranded RNA viruses that cause significant human disease globally. Computational studies have identified multiple potential G-quadruplex sites that are conserved across members of this genus. Subsequent biophysical studies established that some G-quadruplexes predicted in Zika and tickborne encephalitis virus genomes can form and known quadruplex binders reduced viral yields from cells infected with these viruses. The susceptibility of RNA to degradation and the variability of loop regions have made structure determination challenging. Despite these difficulties, we report a high-resolution structure of the NS5-B quadruplex from the West Nile virus genome. Analysis reveals two stacked tetrads that are further stabilized by a stacked triad and transient noncanonical base pairing. This structure expands the landscape of solved RNA quadruplex structures and demonstrates the diversity and complexity of biological quadruplexes. We anticipate that the availability of this structure will assist in solving further viral RNA quadruplexes and provides a model for a conserved antiviral target in Orthoflavivirus genomes.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

Characterizing W sources in the all-W wall, all-RF WEST tokamak environment

In this work, experimental data, together with interpretive modeling tools, are examined to study trends in the tungsten (W) source in the all-W environment of the WEST tokamak, both from the divertor and from the main chamber. In particular, a poloidal limiter protecting an ion cyclotron resonance heating (ICRH) antenna is used as proxy for main chamber sourcing. The key study is carried out by stepping up lower hybrid current drive (LHCD) power, as the only auxiliary power source. Limiter and divertor W sources exhibit a qualitatively similar proportionality to the total power crossing the separatrix, P SEP , although the main chamber source remains substantially lower than the divertor source, for the range of P SEP accessible in the experiments. Intepretive modeling of the limiter source is carried out with a particle-in-cell (PIC) sheath model coupled to a surface sputtering model. Oxygen is used as a proxy for all light impurity species allowing for characterization of the critical W erosion regions. To get a good quantitative match to the data, it is necessary to assume that the oxygen arrives at the surface mostly at high ionization stages (4+ and above). A separate simulation with SOLEDGE-EIRENE, constrained to measured upstream scrape-off-layer plasma profiles, gives oxygen fractional abundances that are compatible with the PIC simulation result. This is understood to arise from transport processes that dominate over recombination. Substituting the LHCD by ICRH, in an equivalent experiment, the local W source exhibits a 3× enhancement. This can be matched by the simulation, by assuming local RF electric field rectification, based on ~100 eV peak-to-peak, near-antennna electric field. This work has highlighted the particular importance of understanding the ion charge state balance of light impurities as these are most likely the dominant sputtering species in fusion devices with high-Z walls.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Interpretative transport modeling of the WEST boundary plasma: main plasma and light impurities

Understanding impurity transport in tokamak plasmas is crucial to control radiative losses and material migration in future magnetic fusion reactors. In this work we deploy the SolEdge2D-EIRENE code to model the boundary plasma in a WEST discharge, satisfactorily reproducing measurements of both upstream and divertor plasma conditions. Additionally, the spatial distribution of oxygen, studied here as a representative light impurity, is compared to vacuum ultraviolet spectroscopy measurements acquired with an oscillating line of sight. The simulation captures a key feature of the experiment, namely a factor of sime2 higher oxygen brightness in the inner divertor region compared to the outer one. This spatial asymmetry in oxygen concentration is interpreted by analyzing the balance of friction forces and thermal gradient forces that the light impurity exchanges with the main plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

WEST full tungsten operation with an ITER grade divertor

The mission of WEST (tungsten-W Environment in Steady-state Tokamak) is to explore long pulse operation in a full tungsten (W) environment for preparing next-step fusion devices (ITER and DEMO) with a focus on testing the ITER actively cooled W divertor in tokamak conditions. Following the successful completion of phase 1 (2016-2021), phase 2 started in December 2022 with the lower divertor made entirely of actively cooled ITER-grade tungsten mono-blocks. A boronization prior the first plasma attempt allowed for a smooth startup with the new divertor. Despite the reduced operating window due to tungsten, rapid progress has been made in long pulse operation, resulting in discharges with a pulse length of 100 s and an injected energy of around 300 MJ per discharge. Plasma startup studies were carried out with equatorial boron nitride limiters to compare them with tungsten limiters, while Ion Cyclotron Resonance Heating assisted startup was attempted. High fluence operation in attached regime, which was the main thrust of the first campaigns, already showed the progressive build up of deposits and appearance of dust, impacting the plasma operation as the plasma fluence increased. In total, the cumulated injected energy during the first campaigns reached 43 GJ and the cumulated plasma time exceeded 5 h. Demonstration of controlled X-Point Radiator regime is also reported, opening a promising route for investigating plasma exhaust and plasma-wall interaction issues in more detached regime. This paper summarises the lessons learned from the manufacturing and the first operation of the ITER-grade divertor, describing the progress achieved in optimising operation in a full W environment with a focus on long pulse operation and plasma wall interaction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Modelling the limiter ramp-up of WEST for addressing the future challenges of ITER

This paper presents a joint experimental and numerical investigation into the physics of long limited plasma ramp-up in tokamaks with tungsten (W) first walls, a critical phase for ITER operation. The comparison between the average plasma quantities simulated using the SolEdge-HDG code and the measurements taken during three successive WEST discharges after boronisation shows how challenging it is to predict this phase. While simulations reproduce the general trends at the midplane, with reasonable match in density profiles, they consistently underestimate core temperatures possibly due to too large perpendicular heat conductivity. On the contrary, at the high field side (HFS) limiter, simulations overestimate the measured quantities, and highlights the limitation of using Bohm boundary conditions at grazing magnetic angles. Experimental measurements reveal that the boron layer is rapidly eroded, on a timescale comparable to a single ITER discharge. The subsequent transition from a boron-coated to a tungsten wall increases recycling and significantly degrades the core plasma, reducing the electron temperature by nearly half due to W contamination, despite wall parameters remaining stable. Furthermore, comparisons with Langmuir probes, bolometry, reflectometry, and spectroscopy indicate that the experimental far scrape-Off layer (SOL) is significantly wider than simulated. This wide SOL implies that boron erosion extends along the entire HFS limiter rather than being confined to the contact point. This work highlights some characteristics of the plasma during this phase of the discharge and emphasizes the current modelling issues that need to be resolved in order to obtain reliable predictions concerning the ITER ramp-up.

ITER↗
DOE OSTI2025

Near-term heatwave risk in HighResMIP models across different temperature zones of West Africa

This study projects near-future (2031–2050) changes in heatwave (HW) risk across West Africa (WA) using an ensemble of eight high-resolution global climate models from the High-Resolution Model Intercomparison Project under a high-emission scenario. Using K-means clustering, we divided WA into four unique temperature zones and examined projected changes in extreme temperatures, HW occurrence and magnitude. Our results indicate a statistically significant increase in future HW events across most parts of WA, although considerable spread exists over the region and among individual models. The most pronounced increases are evident in the Sahel/Sahara and the Guinea Highlands subregions, with an ensemble mean increase of ∼10 HW events per year. In contrast, the lowest increase in HW events is projected in central WA, with increases ranging between 1 and 5 events per year. Similarly, the magnitude of HW events is projected to increase in most models, with Sahel/Sahara exhibiting the largest increases. Additionally, projections suggest that the strongest HWs will become more frequent, particularly in northern and southwestern WA. These findings highlight significant spatial heterogeneity in future HW risk across WA, emphasizing the need for targeted adaptation strategies.

HighResMIP↗
DOE OSTI2022

Opening-mode fracturing and cementation during hydrocarbon generation in shale: An example from the Barnett Shale, Delaware Basin, West Texas

Relative timing of fracturing is a key input for predictive fracture models, but timing information for fractures is commonly difficult to obtain. In this study, we used crosscutting relations and fluid inclusion assemblage temperatures from fracture cements from a few well-documented sampled fractures, combined with a one-dimensional burial history model, to establish timing for three generations of opening-mode fractures in a Barnett Shale core from the southern part of the Delaware Basin, Pecos County, West Texas. A burial history model is presented for the cored well and matched to measured vitrinite reflectance in samples from the core, and bottomhole temperature in the well. Here, the earliest fractures (group 1) likely formed due to early fluid-expulsion events (ca. 300 Ma) and were folded during host-rock compaction. Later group 2 fractures are sealed with fibrous barite containing primary, liquid hydrocarbon inclusions (mean homogenization temperature [T h ] = –9°C) and aqueous fluid inclusions (mean T h = 108.1°C). Group 2 fractures likely formed in response to fluid overpressure associated with cracking of type II kerogen to oil. Group 3 vertical fractures are up to 2 m in height with kinematic apertures ranging from less than 0.05 to 1.4 mm, partly open, and strike dominantly 010°–020°. Sequentially trapped aqueous fluid inclusions in fracture-spanning quartz cement bridges (mean T h = 110°C in crack-seal texture and 128°C in post-crack-seal fracture cement) record fracture opening under increasing temperature, inferred to reflect increasing burial, with continued overpressuring during the Triassic to Late Cretaceous. Some group 3 fractures may have continued to fill during Cenozoic uplift.

02 PETROLEUM↗
DOE OSTI2021

A proposed framework for the development and qualitative evaluation of West Nile virus models and their application to local public health decision-making

West Nile virus (WNV) is a globally distributed mosquito-borne virus of great public health concern. The number of WNV human cases and mosquito infection patterns vary in space and time. Many statistical models have been developed to understand and predict WNV geographic and temporal dynamics. However, these modeling efforts have been disjointed with little model comparison and inconsistent validation. In this paper, we describe a framework to unify and standardize WNV modeling efforts nationwide. WNV risk, detection, or warning models for this review were solicited from active research groups working in different regions of the United States. A total of 13 models were selected and described. The spatial and temporal scales of each model were compared to guide the timing and the locations for mosquito and virus surveillance, to support mosquito vector control decisions, and to assist in conducting public health outreach campaigns at multiple scales of decision-making. Our overarching goal is to bridge the existing gap between model development, which is usually conducted as an academic exercise, and practical model applications, which occur at state, tribal, local, or territorial public health and mosquito control agency levels. The proposed model assessment and comparison framework helps clarify the value of individual models for decision-making and identifies the appropriate temporal and spatial scope of each model. This qualitative evaluation clearly identifies gaps in linking models to applied decisions and sets the stage for a quantitative comparison of models. Specifically, whereas many coarse-grained models (county resolution or greater) have been developed, the greatest need is for fine-grained, short-term planning models (m–km, days–weeks) that remain scarce. We further recommend quantifying the value of information for each decision to identify decisions that would benefit most from model input.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2019

Deep Direct-Use Feasibility Study Numerical Modeling and Uncertainty Analysis using iTOUGH2 for West Virginia University

To reduce the geothermal exploration risk, a feasibility study is performed for a deep direct-use system proposed at the West Virginia University (WVU) Morgantown campus. This study applies numerical simulations to investigate reservoir impedance and thermal production. Because of the great depth of the geothermal reservoir, few data are available to characterize reservoir features and properties. As a result, the study focuses on the following three aspects: 1. model choice for predicting reservoir impedance and thermal breakthrough: after investigating three potential models (one single permeability model and two dual permeability models) for flow through fractured rock, it is decided to use single permeability model for further analysis; 2. well placement (horizontal vs. vertical) options: horizontal well placement seems to be more robust to heterogeneity and the impedance is more acceptable; 3. Prediction uncertainty: the most influential parameters are identified using a First-Order-Second-Moment uncertainty propagation analysis, and the uncertain range of the model predictions is estimated by performing a Monte Carlo simulation. Heterogeneity has a large impact on the perdition, therefore, is considered in the predictive model and uncertainty analysis. The numerical model results and uncertainty analysis are used for economic analysis. The dataset submitted here support the described study. Manuscript is submitted to Geothermics, will be linked once paper is accepted.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Seasonal delay of Sahelian rainfall driven by an east–west contrast in radiative forcing in idealized CESM experiments

Recent studies suggest the observed seasonal delay of rainfall over the Sahel is mainly driven by anthropogenic aerosol forcing, which features a robust east–west contrasting changes in recent decades, with negative and positive top-of-the-atmosphere shortwave radiative forcing in South and East Asia (SA&EA) and in North America and Europe (NA&EU), respectively. Their individual effects on the Sahel rainfall annual cycle remain unclear. Here, by designing idealized sensitivity experiments based on Community Earth System Model (CESM1.2), we show that both negative radiative forcing over SA&EA and positive radiative forcing over NA&EU contribute to the delayed phase and enhanced amplitude of Sahel rainfall annual cycle. To understand the underlying physical processes, both the convective quasi-equilibrium (CQE) and atmospheric energetic frameworks are utilized. Both frameworks can well explain the seasonal delay in the rainfall annual cycle over the Sahel under the regional radiative forcings, with the CQE framework showing stronger explanatory power. Based on the insights from both frameworks, we conducted a moisture budget analysis and found that the negative radiative forcing over SA&EA causes an anomalous low-level anticyclonic circulation, which transports more moisture to the Sahel. As the anomalous anticyclone is stronger in summer and fall compared to spring, rainfall is delayed in the Sahel. Further, under the influence of the positive radiative forcing over NA&EU, more warming in the northern hemisphere causes northward transport of moisture to the northern tropics associated with the cross-equatorial transport of energy. The moisture transport increases relativehumidity over the Sahel and enhances the effective atmospheric heat capacity that delays the seasonal rainfall.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Solid-phase Mn speciation in suspended particles along meltwater-influenced fjords of West Greenland

Manganese (Mn) is an essential micro-nutrient that can limit or, along with iron (Fe), co-limit phytoplankton growth in the ocean. Glacier meltwater is thought to be a key source of trace metals to high latitude coastal systems, but little is known about the nature of Mn delivered to glacially-influenced fjords and adjacent coastal waters. In this work, we combine in-situ dissolved Mn (dMn) measurements of surface waters with Mn K-edge X-ray absorption spectroscopy (XAS) data of suspended particles in four fjords of West Greenland. Data were collected from transects of up to 100 km in fjords with different underlying bedrock geology from 64 to 70°N. We found that dMn concentrations generally decreased conservatively with increasing salinity (from 80 to 120 nM at salinity < 8 to < 40 nM at salinities > 25). Dissolved Fe (dFe) trends in these fjords similarly declined with increasing distance from glacier outflows (declining from > 20 nM to < 8 nM). However, the dMn/dFe ratio increased rapidly likely due to the greater stability of dMn at intermediate salinities (i.e. 10–20) compared to rapid precipitation of dFe across the salinity gradient. The XAS data indicated a widespread presence of Mn(II)-rich suspended particles near fjord surfaces, with structures akin to Mn(II)-bearing phyllosilicates. However, a distinct increase in Mn oxidation state with depth and the predominance of birnessite-like Mn(IV) oxides was observed for suspended particles in a fjord with tertiary basalt geology. The similar dMn behaviour in fjords with different suspended particle Mn speciation (i.e., Mn(II)-bearing phyllosilicates and Mn(IV)-rich birnessite) is consistent with the decoupling of dissolved and particulate Mn and suggests that dMn concentrations on the scale of these fjords are controlled primarily by dilution of a freshwater dMn source rather than exchange between dissolved and particle phases. This work provides new insights into the Mn cycle in high latitude coastal waters, where small changes in the relative availabilities of dMn, dFe and macronutrients may affect the identity of the nutrient(s) proximally limiting primary production.

58 GEOSCIENCES↗