Search NASA⌕ Search

SEARCH · Search NASA

Results for “WING TIP CONTROLS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1959

The Effects of Streamwise-Deflected Wing Tips on the Aerodynamic Characteristics of an Aspect Ratio-2 Triangular Wing, Body, and Tail Combination

An investigation has been conducted on a triangular wing and body combination to determine the effects on the aerodynamic characteristics resulting from deflecting portions of the wing near the tips 900 to the wing surface about streamwise hinge lines. Experimental data were obtained for Mach numbers of 0.70, 1.30, 1.70, and 2.22 and for angles of attack ranging from -5 deg to +18 deg at sideslip angles of 0 deg and 5 deg. The results showed that the aerodynamic center shift experienced by the triangular wing and body combination as the Mach number was increased from subsonic to supersonic could be reduced by about 40 percent by deflecting the outboard 4 percent of the total area of each wing panel. Deflection about the same hinge line of additional inboard surfaces consisting of 2 percent of the total area of each wing panel resulted in a further reduction of the aerodynamic center travel of 10 percent. The resulting reductions in the stability were accompanied by increases in the drag due to lift and, for the case of the configuration with all surfaces deflected, in the minimum drag. The combined effects of reduced stability and increased drag of the untrimmed configuration on the trimmed lift-drag ratios were estimated from an analysis of the cases in which the wing-body combination with or without tips deflected was assumed to be controlled by a canard. The configurations with deflected surfaces had higher trimmed lift-drag ratios than the model with undeflected surfaces at Mach numbers up to about 1.70. Deflecting either the outboard surfaces or all of the surfaces caused the directional stability to be increased by increments that were approximately constant with increasing angle of attack at each Mach number. The effective dihedral was decreased at all angles of attack and Mach numbers when the surfaces were deflected.

Peterson, Victor L.↗
NASA NTRS1944

Aerodynamic Tests of a Full-scale TBF-1 Aileron Installation in the Langley 16-foot High-Speed Tunnel

The failure of wing panels on a number of TBF-1 and TBM-1 airplanes in flight has prompted several investigations of the possible causes of failure. This report describes tests in the Langley 16-foot high-speed tunnel to determine whether these failures could be attributed to changes in the aerodynamic characteristics of the ailerons at high speeds. The tests were made of a 12-foot-span section including the tip and aileron of the right wing of a TBF-1 airplane. Hinge moments, control-link stresses due to aerodynamic buffeting, and fabric-deflection photographs were obtained at true airspeeds ranging from 110 to 365 miles per hour. The aileron hinge-moment coefficients were found to vary only slightly with airspeed in spite of the large fabric deflections that developed as the speed was increased. An analysis of these results indicated that the resultant hinge moment of the ailerons as installed in the airplane would tend to restore the ailerons to their neutral position for all the high-speed flight conditions covered in the tests. Serious aerodynamic buffeting occurred at up aileron angles of -10 degrees or greater because of stalling of the sharp projecting lip of the Frise aileron. The peak stresses set up in the aileron control linkages in the buffeting condition were as high as three times the mean stress. During the hinge-moment investigation, flutter of the test installation occurred at airspeeds of about 150 miles per hour. This flutter condition was investigated in some detail and slow-motion pictures were made of the motion of the wing tip and aileron. The flutter was found to involve simultaneous normal bending and chordwise oscillation of the wing and flapping of the aileron. The aileron motion appeared to be coupled with this flutter condition and was investigated in some detail and slow-motion pictures were made of the motion of the wing tip and aileron. The flutter was found to involve simultaneous normal bending and chordwise oscillation of the wing and flapping of the aileron. The aileron motion appeared to be coupled with the motion of the wing through the mass unbalance of the aileron in the normal-to-chord plane due to location of the hinge line 2.17 inches below the center of gravity of the aileron. Flutter did not occur when the installation was stiffened to prevent chordwise motion or when the bending frequency of the aileron system was appreciably higher than that of the wing as in the complete airplane installation.

Becker, John V↗
NASA NTRS1945

Determination of the Stability and Control Characteristics of a Tailless All-Wing Airplane Model with Sweepback in the Langley Free-Flight Tunnel

Force and flight tests were performance on an all-wing model with windmilling propellers. Tests were conducted with deflected and retracted flaps, with and without auxiliary vertical tail surfaces, and with different centers of gravity and trim coefficients. Results indicate serious reduction of stick-fixed longitudinal stability because of wing-tip stalling at high lift coefficient. Directional stability without vertical tail is undesirably low. Low effective dihedral should be maintained. Elevator and rudder control system is satisfactory.

WING FLAPS - DEFLECTION↗
NASA NTRS1977

Optimal control alleviation of tilting proprotor gust response

Optimal control theory is applied to the design of a control system for alleviation of the gust response of tilting proprotor aircraft. Using a proprotor and cantilever wing analytical model, the uncontrolled and controlled gust response is examined over the entire operating range of the aircraft except for hover: helicopter mode, conversion, and airplane mode flight. Substantial improvements in the loads, ride quality, and aeroelastic stability are possible with a properly designed controller. A single controller, nominally optimal only at the design point speed (160 knots here), operated efficiently over the entire speed range, with the possible exception of very low speed in helicopter mode. Kalman-Bucy filters were used as compensation networks to provide state estimates from various measurements in the system. Efficient control requires the measurement of the wing motion, rotor speed perturbation, and tip-path-plane tilt.

Johnson, W.↗
NASA NTRS1986

Subsonic aerodynamic characteristics of a circular body earth-to-orbit transport

To reduce the weight and improve the performance of future earth-to-orbit transports, the use of circular cross sections in the fuselage bodies of these vehicles is being considered at the Langley Research Center. Structurally, circular cross sections are stronger and lighter than other shapes. A study has been made applying the circular body concept to a vertical-takeoff, delta-winged, single-stage-to-orbit transport. A 52 in., 0.022-scale model of the circular body vehicle was tested at a Mach number of 0.3 in the 7 x 10 ft High Speed Wind Tunnel at the Langley Research Center to obtain aerodynamic forces and moments. Oil-flow photographs were taken at several angles of attack to aid in the aerodynamic analysis. Model control surfaces included elevons and ailerons for the evaluation of pitch and roll characteristics and either wing-tip fins, a nose mounted dorsal fin, or a conventional vertical tail for the evaluation of yaw characteristics. Other deflecting surfaces included speedbrakes and body flaps. Basic data on longitudinal flight characteristics are shown, including lift, drag, and pitching moments. Comparisons of the directional stability and control effectiveness of the three directional control devices are also shown.

Lepsch, R. A., Jr.↗
NASA NTRS1978

Preliminary study of a large span-distributed-load flying-wing cargo airplane concept

An aircraft capable of transporting containerized cargo over intercontinental distances is analyzed. The specifications for payload weight, density, and dimensions in essence configure the wing and establish unusually low values of wing loading and aspect ratio. The structural weight comprises only about 18 percent of the design maximum gross weight. Although the geometric aspect ratio is 4.53, the winglet effect of the wing-tip-mounted vertical tails, increase the effective aspect ratio to approximately 7.9. Sufficient control power to handle the large rolling moment of inertia dictates a relatively high minimum approach velocity of 315 km/hr (170 knots). The airplane has acceptable spiral, Dutch roll, and roll-damping modes. A hardened stability augmentation system is required. The most significant noise source is that of the airframe. However, for both take-off and approach, the levels are below the FAR-36 limit of 108 db. The design mission fuel efficiency is approximately 50 percent greater than that of the most advanced, currently operational, large freighter aircraft. The direct operating cost is significantly lower than that of current freighters, the advantage increasing as fuel price increases.

Jernell, L. S.↗
NASA NTRS1979

Low-speed aerodynamic performance of a high-aspect-ratio supercritical-wing transport model equipped with full-span slat and part-span double-slotted flaps

An investigation was conducted in the Langley V/STOL tunnel to determine the static longitudinal and lateral-directional aerodynamic characteristics of an advanced high-aspect-ratio supercritical-wing transport model equipped with a full-span leading-edge slat and part-span double-slotted trailing-edge flaps. This wide-body transport model was also equipped with spoiler and aileron control surfaces, flow-through nacelles, landing gear, movable horizontal tails, and interchangeable wing tips with aspect ratios of 10 and 12. The model was tested with leading-edge slat and trailing-edge flap combinations representative of cruise, climb, takeoff, and landing wing configurations. The tests were conducted at free-stream conditions corresponding to Reynolds numbers (based on mean geometric chord) of 0.97 to 1.63 x 10 to the 6th power and corresponding Mach numbers of 0.12 to 0.20, through an angle-of-attack range of -2 deg to 24 deg and a sideslip-angle range of -10 deg to 5 deg.

Morgan, H. L., Jr.↗
NASA NTRS1946

Free-Spinning Tunnel Tests of a 1/20-Scale Model of the Chance Vought XF6U-1 Airplane, TED No. NACA 2390

A spin investigation has been conducted in the Langley 20-foot free-spinning tunnel on a 1/20-scale model of the Chance Vought XF6U-1 airplane, The effects of control settings and movements upon the erect and inverted spin and recovery characteristics of the model were determined for the normal-fighter condition. The investigation also included tests for the take-off fighter condition (wing-tip tanks plus fuel added) spin-recovery parachutes, and simulated pilot escape. In general, for the normal-fighter condition, the model was extremely oscillatory in roll, pitch, and yaw. The angles of the fuselage varied from extremely flat to inverted attitudes, and the model rotated with the rudder in a series of short turns and glides. Recoveries by rudder reversal were rapid but the model would immediately go into a spin in the other direction. Recoveries by merely neutralizing the rudder were satisfactory when the elevator and ailerons were set to neutral, the ensuing flight path being a steep glide. Thus, it is recommended that all controls be neutralized for safe recovery from spins obtained on the airplane. With the external wing-tip tanks installed, the spins were somewhat less oscillatory in roll but recovery could not be obtained unless full-down elevator was used in conjunction with the rudder. If a spin is entered inadvertently with the full-scale airplane with external wing-tip tanks installed and if recovery is not imminent after a recovery attempt is made, it is recommended that the tanks be jettisoned and the controls neutralized.

Klinar, Walter J.↗
NASA NTRS1983

Adaptive flutter suppression, analysis and test

Methods of adaptive control have been applied to suppress a potentially violent flutter condition of a half-span model of a lightweight figher aircraft. This marked the confluence of several technologies with active flutter suppression, digital control and adaptive control theory the primary contributors. The control algorithm was required to adapt both to slowly varying changes, corresponding to changes in the flight condition or fuel loading and to rapid changes, corresponding to a store release or the transition from a stable to an unstable flight condition. The development of the adaptive control methods was followed by a simulation and checkout of the complete system and a wind tunnel demonstration. As part of the test, a store was released from the model wing tip, transforming the model abruptly from a stable configuration to a violent flutter condition. The adaptive algorithm recognized the unstable nature of the resulting configuration and implemented a stabilizing control law in a fraction of a second. The algorithm was also shown to provide system stability over a range of wind tunnel Mach numbers and dynamic pressures.

Johnson, E. H.↗
NASA NTRS1959

Exploratory Investigation at Mach Number of 2.01 of the Longitudinal Stability and Control Characteristics of a Winged Reentry Configuration

An investigation has been conducted to determine the longitudinal stability and control characteristics of a reentry configuration at a Mach number of 2.01. The configuration consisted of clipped delta wing with hinged wing-tip panels. The results indicate that deflecting the wing-tip panels from a position normal to the wing chord plane to a position coincident with the wing chord plane resulted in a stabilizing change in the pitching-moment characteristics but did not significantly affect the nonlinearity of the pitching-moment variation with angle of attack. The trailing-edge controls were effective in producing pitching moment throughout the angle-of-attack range for control deflections up to at least 600. The control deflection required for trim, however, varied nonlinearly with angle of attack. It would appear that this nonlinearity as well as the maximum deflection required for trim could be greatly decreased by utilizing a leading-edge control in conjunction with a trailing-edge control.

Foster, Gerald V.↗
NASA NTRS1979

Vortex-lift roll-control device

A wing is described for aircraft of cropped, arrow-type planform with thin leading and side edges. The wing has a pivotable tip to alter the crop angle of the wing during flight. Increasing the crop angle causes the wing side edge to become a trailing edge which reduces the strength of the side edge vortex flow. Decreasing the crop angle causes opposite results, in particular the side edge is now a leading edge and can generate a leading edge vortex flow. The wing constitutes a roll control device for aircraft of the stated design particularly effective at higher angles of attack.

Lamar, J. E.↗
NASA NTRS1983

Acoustic measurements of the X-wing rotor

Noise measurements of a stoppable X-wing rotor system model, tested in the Ames 40- by 80-foot wind tunnel, are summarized. Performance, control system stability, and noise of the model were investigated at various forward speeds, tip speeds, collective blade angles, jet blowing velocities, and model attack angles. The model was tested in the rotating wing helicopter configuration, in the fixed wing configuration, and in wing configurations between the two. Noise data obtained in the helicopter configuration at the two highest tip speeds (Mach 0.44 and 0.47) and at wind tunnel speeds below 140 knots are reported. Test configuration and performance information are included. General acoustic measurements (dB, dBA, and PNdB) at six microphone locations are presented for all conditions under which the background noise was below the model noise. More specific measurements (1/3-octave and blade passage frequency harmonic levels) are presented for selected conditions. Graphs of dBA and 1/3-octave spectra, which show the noise trends as functions of operating condition, are included. The noise depends mainly on the jet blowing velocity. The noise levels were highest at moderate jet blowing velocities, less at the highest velocity, and lowest with no blowing at all.

Mosher, M.↗
NASA NTRS1983

The tilt rotor research aircraft (XV-15) program

The tilt rotor concept is introduced and the performance capabilities and noise characteristics of the XV-15 aircraft are discussed. In hover, the aircraft is lifted by the two wing tip mounted rotors with the nacelles in the vertical position. In this flight mode, the vehicle is a twin rotor helicopter and is controlled by rotor cyclic and collective controls. The aircraft can fly as a helicopter or tilt the nacelle to the propeller mode and operate as a fixed-wing twin turboprop airplane. It is also possible to stop the conversion at any intermediate angle and fly continuously or reconvert. The rotors are powered by two modified T-53 engines and the power train includes a cross shaft located in the wing, to allow for the engine failure case and still retain power to both rotors.

Magee, J. P.↗
NASA NTRS1948

Free-Spinning-Tunnel Tests of a 1/24-Scale Model of the Grumman XF9F-2 Airplane with Wing-Tip Tanks Installed

An investigation of the spin and recovery characteristics of a 1/24-scale model of the Grumman XF9F-2 airplane with wing-tip tanks installed has been conducted-in the Langley 20-foot free-spinning tunnel. The effects of control settings and movements on the erect spin and recovery characteristics of the model for a range of possible loadings of the tip tanks were determined. Spin and recovery characteristics without tanks were determined in a previous investigation. The model results indicated that the airplane spins will generally be oscillatory and that recoveries will be satisfactory for all loadings by normal recovery technique (full rudder reversal followed approximately one-half turn later by moving the elevator down). The rudder force necessary for recovery should be within the physical capability of the pilot but the elevator force may be excessive so that some type of balance or booster might be necessary, or it might be necessary to jettison the wing-tip tanks.

Berman, Theodore↗
NASA NTRS1932

Preliminary investigation of rolling moments obtained with spoilers on both slotted and plain wings

A wind-tunnel study has been made to determine the possibility of developing spoilers suitable for providing the lateral control for airplanes in place of the usual ailerons. The first tests were made on a model wing with a fixed tip slot, but when it was found that the effectiveness of the spoilers did not depend to any great extent on the slot, tests were made on a plain wing also. In both cases certain spoiler positions were found which were free from the usual adverse rolling moments with small deflections. Five different forms of spoiler were tested, the best ones being simple plates, either straight or slightly curved to fit the contour of the airfoil when not deflected. Sufficient rolling moment can probably be obtained from spoilers of reasonable size to provide satisfactory lateral control for certain types of airplanes.

Weick, Fred E↗
NASA NTRS1924

The Measurement of the Damping in Roll on a Jn4h in Flight

This investigation was carried out by the National Advisory Committee for Aeronautics for the purpose of measuring the value of L sub P in flight. The method consisted in flying with heavy weights on each wing tip, suddenly releasing one of them, and allowing the airplane to roll up to 90 degrees with controls held in neutral while a record was being taken of the airspeed, and angular velocity about the X axis. The results are of interest as they show that the damping found in the wind tunnel by the method of small oscillations is in general 40 per cent higher than the damping in flight. At 50 M. P. H. The flight curve of L sub P has a high peak, which is not indicated in the model results. It is also shown that at this speed the lateral maneuverability is low.

Norton, F H↗
NASA NTRS1979

Extended analytical study of the free-wing/free-trimmer concept

The free wing/free trimmer concept was analytically studied in order to: (1) compare the fore and aft trimmer configurations on the basis of equal lift capability, rather than equal area; (2) assess the influence of tip mounted aft trimmers, both free and fixed, on the lateral directional modes and turbulence responses; (3) examine the feasibility of using differential tip mounted trimmer deflection for lateral control; (4) determine the effects of independent fuselage attitude on the lateral directional behavior; and (5) estimate the influence of wing sweep on dynamic behavior and structural weight. Results indicate that the forward trimmer concept is feasible with the reduced size examined, but it remains inferior to the aft trimmer in every respect except structural weight. Differential motion of the aft trimmer is found to provide powerful lateral control; while the effect of fuselage deck angle is a reduction of the dutch roll damping ratio for nose-down attitudes.

Porter, R. F.↗
NASA NTRS1942

Comparison of Aileron Control Characteristics as Determined in Flight Tests of P-36, P-40, Spitfire, and Hurricane Pursuit Airplanes

The Army Air Force has made available several pursuit-type airplanes for quantitative investigation of their flying and handling qualities. One Item of special interest obtained from the results of the investigation is a comparison of the aileron control characteristics of the P-36, P-40, Hawker Hurricane, and Supermarine Spitfire airplanes. Figure 1 shows the design characteristics of the ailerons and the control sticks of the four airplanes. Aileron effectiveness may be expressed in terms of the helix angle generated by the wing tip in a steady roll. This angle is given by the expression pb/2V, where p is the rolling velocity, b the wing span, and V the true airspeed, expressed in consistent units. This quantity is convenient to use because, although it does not rep resent directly the rolling velocity of airplanes of different spans or airplanes operating at different speeds, it provides a satisfactory basis for computing the rate of roll and the time required to bank a given amount under any given set of conditions. The ratio of pb/2V obtained in any roll to the maximum value reached with full aileron deflection indicates the fraction of the maximum aileron travel that was reached. A complete discussion of this criterion for aileron effectiveness is given in reference 1. The aileron effectiveness of the various airplanes is compared in the following table on the basis of the response obtained with stick forces of 30 and 5 pounds. A force of 30 pounds is somewhat less than the greatest stick force exerted by the pilot. Repeated flight measurements have shown, however, that this force is a reasonable upper limit for maneuvering at high speeds.

Phillips, William H.↗