Search NASA⌕ Search

SEARCH · Search NASA

Results for “YAWING MOMENTS - AILERONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1948

Stability derivatives of triangular wings at supersonic speeds

The analysis of the stability derivatives of low-aspect-ratio triangular wings at subsonic and supersonic speeds, given in NACA TN no. 1423, is extended to apply to triangular wings having large vertex angles and traveling at supersonic speeds. The lift, rolling moment due to sideslip, and damping in roll and pitch for this more general case have been treated elsewhere on the basis of the theory of small disturbances. The surface potentials for angle of attack and rolling taken therefrom are used to obtain the several side-force and yawing-moment derivatives that depend on leading-edge suction, and a tentative value for the rolling moment due to yawing. The lift and moment due to downward acceleration are obtained on the basis of an unpublished unsteady-flow solution. All the known stability derivatives of the triangular wing at supersonic speeds, regardless of source, are summarized for convenience and presented with respect to both body axes and stability axes. The results are limited to Mach numbers for which the triangular wing is contained within the Mach cone for its vertex. The spanwise variation of Mach number in the case of yawing is neglected, although the effect must be of importance.

Ribner, Herbert S↗
NASA NTRSDate not supplied

Force and Moment Analysis for the High Reynolds Number Wind Tunnel Test of the Space Launch System at Ascent Conditions

A high Reynolds number test of the Space Launch System was performed at the NASA Langley National Transonic Facility (NTF). The objective of the test was to use the cryogenic testing capabilities of the NTF to acquire data over the largest range of Reynolds numbers possible with a specific focus on the Reynolds numbers closest to flight conditions. The test was performed at Mach numbers from 0.50 to 0.95 which corresponds to the ascent portion of flight for the SLS vehicle. Force and moment data showed that pitching and yawing moment were sensitive to Reynolds number effects over the full range of Mach and Reynolds numbers tested. Axial force also showed sensitivity to Reynolds number with the largest differences seen between Mach 0.50 to 0.90. Surface pressure data showed the highest sensitivity to Reynolds number in the vicinity of the solid rocket booster forward attach region.

Space Launch System↗
NASA NTRSDate not supplied

Force and Moment Analysis for the High Reynolds Number Wind Tunnel Test of the Space Launch System at Ascent Conditions

A high Reynolds number test of the Space Launch System was performed at the NASA Langley National Transonic Facility (NTF). The objective of the test was to use the cryogenic testing capabilities of the NTF to acquire data over the largest range of Reynolds numbers possible with a specific focus on the Reynolds numbers closest to flight conditions. The test was performed at Mach numbers from 0.50 to 0.95, which corresponds to the ascent portion of flight for the SLS vehicle. Force and moment data showed that pitching and yawing moment were sensitive to Reynolds number effects over the full range of Mach and Reynolds numbers tested. Axial force also showed sensitivity to Reynolds number with the largest differences seen between Mach 0.50 to 0.90. Surface pressure data showed the highest sensitivity to Reynolds number in the vicinity of the solid rocket booster forward attach region.

Space Launch System↗
NASA NTRS1939

Pressure-distribution Measurements on a Tapered Wing with a Full-span Split Flap in Curved Flight

Pressure-distribution tests were made on the 32-foot whirling arm of the Daniel Guggenheim Airship Institute of a tapered wing to determine the rolling and yawing moments due to an angular velocity in yaw. The model was tested at 0 degree and 5 degrees pitch, -1 degree and 5 degree yaw, and with a full-span flap deflected 60 degrees. The results are given in the form of span load distributions and in calculated moment coefficients. The rolling-moment coefficients are in fairly close agreement with those derived by means of a simple approximate theory even for high deflection of the full-span flap.

Troller, TH↗
NASA NTRS1981

Space shuttle solid rocket booster sting interference wind tunnel test analysis

Wind tunnel test results from shuttle solid rocket booster (SRB) sting interference tests were evaluated, yielding the general influence of the sting on the normal force and pitching moment coefficients and the side force and yawing moment coefficients. The procedures developed to determine the sting interference, the development of the corrected aerodynamic data, and the development of a new SRB aerodynamic mathematical model are documented.

Conine, B.↗
NASA NTRS1990

Flight investigation of the effect of tail boom strakes on helicopter directional control

A joint U.S. Army/NASA flight investigation was conducted utilizing an instrumented Bell 240B single-rotor helicopter to determine the effectiveness of horizontally-mounted tail boom strakes on directional controllability and tail rotor power required during low-speed, crosswind operating conditions. The purpose of the strakes was to separate airflow over the tail boom and change fuselage yawing moments in a direction to improve the yaw control margin and reduce tail rotor power required. Low-speed crosswind data were obtained in 5-knot increments at airspeeds of 0 knots to 35 knots and for 30 deg increments in wind azimuth from 0 to 330 deg. In right sideward flight at the most critical wind azimuth and airspeed (60 deg azimuth measured from the nose of the aircraft and 20 knots airspeed), the strakes improved the pedal margin by about 6 percent of total travel and reduced the tail rotor power required by 17 percent. The increase in yaw control and reduction in tail rotor power offered by the strakes can expand the operating envelope in terms of gross weight and altitude capability. No effects in forward flight were noted.

Kelley, Henry L.↗
NASA NTRS1991

Hub and pylon fairing integration for helicopter drag reduction

The results of testing hub and pylon fairings mounted on a one-fifth scale helicopter with the goal of reducing parasite drag are presented. Lift, drag, and pitching moment, as well as side force and yawing moment, were measured. The primary objective of the test was to validate the drag reduction capability of integrated hub and pylon configurations in the aerodynamic environment produced by a rotating hub in forward flight. In addition to the baseline helicopter without fairings, three hub fairings and three pylon fairings were tested in various combinations. The three hub fairings tested reflect two different conceptual design approaches to implementing an integrated fairing configuration on an actual aircraft. The design philosophy is discussed in detail and comparisons are made between the wind tunnel models and potential full-scale prototypes. The data show that model drag can be reduced by as much as 20.8 percent by combining a small hub fairing with circular arc upper and flat lower surfaces and a nontapered 34-percent thick pylon fairing. Aerodynamic effects caused by the fairings, which may have a significant impact on static longitudinal and directional stability, were observed. The results support previous research which showed that the greatest reduction in model drag is achieved if the hub and pylon fairings are integrated with minimum gap between the two.

Martin, D. M.↗
NASA NTRS1993

Flight investigation of the effect of tail boom strakes on helicopter directional control

A joint U.S. Army/NASA flight investigation was conducted utilizing a single-rotor helicopter to determine the effectiveness of horizontally mounted tail boom strakes on directional controllability and tail rotor power during low-speed, crosswind operating conditions. Three configurations were investigated: (1) baseline (strakes off), (2) single strake (strake at upper shoulder on port side of boom), and (3) double strake (upper strake plus a lower strake on same side of boom). The strakes were employed as a means to separate airflow over the tail boom and change fuselage yawing moments in a direction to improve the yaw control margin and reduce tail rotor power. Crosswind data were obtained in 5-knot increments of airspeed from 0 to 35 knots and in 30 deg increments of wind azimuth from 0 deg to 330 deg. At the most critical wind azimuth and airspeed in terms of tail rotor power, the strakes improved the pedal margin by 6 percent of total travel and reduced tail rotor power required by 17 percent. The increase in yaw control and reduction in tail rotor power offered by the strakes can expand the helicopter operating envelope in terms of gross weight and altitude capability. The strakes did not affect the flying qualities of the vehicle at airspeeds between 35 and 100 knots.

Kelly, Henry L.↗
NASA NTRS1975

Exploratory flight investigation of aircraft response to the wing vortex wake generated by the augmentor wing jet STOL research aircraft

A brief exploratory flight program was conducted at Ames Research Center to investigate the vortex wake hazard of a powered-lift STOL aircraft. The study was made by flying an instrumented Cessna 210 aircraft into the wake of the augmentor wing jet STOL research aircraft at separation distances from 1 to 4 n.mi. Characteristics of the wake were evaluated in terms of the magnitude of the upset of the probing aircraft. Results indicated that within 1 n.mi. separation the wake could cause rolling moments in excess of roll control power and yawing moments equivalent to rudder control power of the probe aircraft. Subjective evaluations by the pilots of the Cessna 210 aircraft, supported by response measurements, indicated that the upset caused by the wake of the STOL aircraft was comparable to that of a DC-9 in the landing configuration.

Jacobsen, R. A.↗
NASA NTRS1981

Some experiments on Yaw stability of wind turbines with various coning angles

A horizontal axis wind turbine was constructed to study the effect of coning angle on the yawing moments produced. Coning angles of 0 deg, +10 deg and -10 deg were studied in the upwind and downwind cases. Moment and rotational frequency of the blades at each yaw angle setting were taken. It was found that as the coning angle increased from -10 deg to +10 deg in either the upwind or downwind case the stability decreased. The downwind case was slightly more stable for all coning angles than was the upwind case. It is found that all the previous cases were stable for high rotation speeds, but at lower rotation speeds, they were all unstable and could not self start unless held in the wind.

Bundas, D.↗
NASA NTRS1999

Aerodynamic Characteristics and Control Effectiveness of the HL-20 Lifting Body Configuration at Mach 10 in Air

A 0.0196-scale model of the HL-20 lifting-body, one of several configurations proposed for future crewed spacecraft, was tested in the Langley 31-Inch Mach 10 Tunnel. The purpose of the tests was to determine the effectiveness of fin-mounted elevons, a lower surface flush-mounted body flap, and a flush-mounted yaw controller at hypersonic speeds. The nominal angle-of-attack range, representative of hypersonic entry, was 2 deg to 41 deg, the sideslip angles were 0 deg, 2 deg, and -2 deg, and the test Reynolds number was 1.06 x 10 E6 based on model reference length. The aerodynamic, longitudinal, and lateral control effectiveness along with surface oil flow visualizations are presented and discussed. The configuration was longitudinally and laterally stable at the nominal center of gravity. The primary longitudinal control, the fin-mounted elevons, could not trim the model to the desired entry angle of attack of 30 deg. The lower surface body flaps were effective for roll control and the associated adverse yawing moment was eliminated by skewing the body flap hinge lines. A yaw controller, flush-mounted on the lower surface, was also effective, and the associated small rolling moment was favorable.

Scallion, William I.↗
NASA NTRS1929

Forces on Elliptic Cylinders in Uniform Air Stream

This report presents the results of wind tunnel tests on four elliptic cylinders with various fineness ratios, conducted in the Navy Aerodynamic Laboratory, Washington. The object of the tests was to investigate the characteristics of sections suitable for streamline wire which normally has an elliptic section with a fineness ratio of 4.0; also to learn whether a reduction in fineness ratio would result in improvement; also to determine the pressure distribution on the model of fineness ratio of 4. Four elliptic cylinders with fineness ratios of 2.5, 3.0, 3.5, and 4.0 were made and then tested in the 8 by 8 wind tunnel; first, for cross-wind force, drag, and yawing moment at 30 miles an hour and various angles of yaw; next for drag 0 degree pitch and 0 degree yaw and various wind speeds; then for end effect on the smallest and largest models; and lastly for pressure distribution over the surface of the largest model at 0 degree pitch and 0 degree yaw and various wind speeds. In all tests, the length of the model was transverse to the current. The results are given for standard air density, p = .002378 slug per cubic foot. This account is a slight revised form of report no. 315. A summary of conclusions is given at the end of the text. (author)

Zahm, A F↗
NASA NTRS1981

Calculation of lateral-directional stability derivatives of wings by a nonplanar quasi-vortex-lattice method

The nonplanar quasi-vortex-lattice method is applied to the calculation of lateral-directional stability derivatives of wings with and without vortex-lift effect. Results for conventional configurations and those with winglets, V-tail, etc. are compared with available data. All rolling moment derivatives are found to be accurately predicted. The prediction of side force and yawing moment derivatives for some configurations is not as accurate. Causes of the discrepancy are discussed. A user's manual for the program and the program listing are also included.

Lan, C. E.↗
NASA NTRS2002

Modeling and Simulation of a Helicopter Slung Load Stabilization Device

This paper addresses the problem of simulation and stabilization of the yaw motions of a cargo container slung load. The study configuration is a UH-60 helicopter carrying a 6ft x 6 ft x 8 ft CONEX container. This load is limited to 60 KIAS in operations and flight testing indicates that it starts spinning in hover and that spin rate increases with airspeed. The simulation reproduced the load yaw motions seen in the flight data after augmenting the load model with terms representing unsteady load yaw moment effects acting to reinforce load oscillations, and augmenting the hook model to include yaw resistance at the hook. The use of a vertical fin to stabilize the load is considered. Results indicate that the CONEX airspeed can be extended to 110 kts using a 3x5 ft fin.

Cicolani, Luigi S.↗
NASA NTRS2011

Engine Yaw Augmentation for Hybrid-Wing-Body Aircraft via Optimal Control Allocation Techniques

Asymmetric engine thrust was implemented in a hybrid-wing-body non-linear simulation to reduce the amount of aerodynamic surface deflection required for yaw stability and control. Hybrid-wing-body aircraft are especially susceptible to yaw surface deflection due to their decreased bare airframe yaw stability resulting from the lack of a large vertical tail aft of the center of gravity. Reduced surface deflection, especially for trim during cruise flight, could reduce the fuel consumption of future aircraft. Designed as an add-on, optimal control allocation techniques were used to create a control law that tracks total thrust and yaw moment commands with an emphasis on not degrading the baseline system. Implementation of engine yaw augmentation is shown and feasibility is demonstrated in simulation with a potential drag reduction of 2 to 4 percent. Future flight tests are planned to demonstrate feasibility in a flight environment.

Taylor, Brian R.↗
NASA NTRS2011

Engine Yaw Augmentation for Hybrid-Wing-Body Aircraft via Optimal Control Allocation Techniques

Asymmetric engine thrust was implemented in a hybrid-wing-body non-linear simulation to reduce the amount of aerodynamic surface deflection required for yaw stability and control. Hybrid-wing-body aircraft are especially susceptible to yaw surface deflection due to their decreased bare airframe yaw stability resulting from the lack of a large vertical tail aft of the center of gravity. Reduced surface deflection, especially for trim during cruise flight, could reduce the fuel consumption of future aircraft. Designed as an add-on, optimal control allocation techniques were used to create a control law that tracks total thrust and yaw moment commands with an emphasis on not degrading the baseline system. Implementation of engine yaw augmentation is shown and feasibility is demonstrated in simulation with a potential drag reduction of 2 to 4 percent. Future flight tests are planned to demonstrate feasibility in a flight environment.

Taylor, Brian R.↗
NASA NTRS1985

Low-speed wind-tunnel tests of an advanced eight-bladed propeller

As part of a research program on advanced turboprop aircraft aerodynamics, a low-speed wind-tunnel investigation was conducted to document the basic performance and force and moment characteristics of an advanced eight-bladed propeller. The results show that in addition to the normal force and pitching moment produced by the propeller/nacelle combination at angle of attack, a significant side force and yawing moment are also produced. Furthermore, it is shown that for test conditions wherein compressibility effects can be ignored, accurate simulation of propeller performance and flow fields can be achieved by matching the nondimensional power loading of the model propeller to that of the full-scale propeller.

Coe, P. L., Jr.↗
NASA NTRS1993

A sensitivity study for pneumatic vortex control on a chined forebody

A study was conducted to assess the sensitivity of yaw control on a chined forebody to the longitudinal location of a blowing slot at the chine edge. In addition, the effects of port blowing were also studied. NASA Langley's thin-layer Navier-Stokes code CFL3D was used to compare flow field characteristics and total yawing moment coefficients for the blowing configurations. Based upon equivalent blowing momentum coefficients, a significant increase in yaw control effectiveness was attained from the forward slot, relative to the aft slot, and port blowing was less effective than either slot blowing configuration.

Boalbey, R. E.↗