SEARCH · Search NASA

Results for “absorbed power”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Experimental evaluation of active and passive means of alleviating rotor impulsive noise in descent flight

A controlled wind tunnel test program was conducted on a model 2.14 m (7 ft) diameter teetering rotor to determine the effectiveness of blade tips such as the Ogee tip and the TAMI (Tip Air Mass Injection) tip in reducing the impulsive noise due to blade-vortex interaction in descent flight. In addition, a full rectangular tip which has the same span as the Ogee tip and an effective rectangular tip which has the same lifting area as the Ogee tip were also considered. The tests were conducted at two advance ratios (0.125 and 0.14) with various descent rates ranging from steady level flight to about 6 m/sec (20 ft/sec). A comparison of the performance of different rotors showed that for the same tip Mach number and thrust, the Ogee tip rotor absorbed more power than the full rectangular tip rotor, while the TAMI tip rotor absorbed more power than the effective tip rotor.

Janakiram, D. S.↗

DOE OSTI2026

Mitigating Data Center Impact on Grid Stability: A Coordinated Control Strategy Using Verrus StabiliGrid Architecture

Large data centers, which now represent a significant and growing share of the total U.S. grid load, can inadvertently destabilize the electrical grid when they disconnect simultaneously during brief voltage disturbances. The July 10, 2024, Eastern Interconnection incident, in which a sub-100-millisecond transmission fault triggered the cascading loss of approximately 1,500 MW of data center load, illustrates this vulnerability. While commercial battery energy storage systems (BESS) deployed in data centers provide device-level fault ride-through per IEEE 1547, they lack coordination with facility protection logic and uninterruptible power supplies (UPS), limiting their effectiveness as grid-stabilizing assets. This report presents the Verrus StabiliGrid architecture, a coordinated control framework that integrates BESS, UPS, and point-of-interconnection (POI) protection settings to enable data centers to ride through both undervoltage and overvoltage grid contingencies without disconnecting. The four-step strategy encompasses: (1) high-resolution power quality monitoring to detect the grid state during events such as undervoltage, overvoltage, underfrequency, and overfrequency; (2) POI protection settings that allow for extended ride-through and grid-connected operation during grid contingencies; (3) grid state-driven autonomous dispatch of assets to improve grid resilience by reducing power draw during undervoltage or absorbing more power during overvoltage events; and (4) coordinated post-recovery dispatch of data center assets to restore firm load to pre-contingency levels. Validated through controller-hardware-in-the-loop (C-HIL) simulations at the National Laboratory of the Rockies, results show grid import restoration to pre-fault levels within 100 milliseconds of voltage recovery. This work advances the ability of data centers to transition from passive, disturbance-sensitive loads to active participants in grid stability, a capability increasingly required by emerging NERC and ERCOT regulatory frameworks.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2020

High-efficiency, air-stable manganese–iron oxide nanoparticle-pigmented solar selective absorber coatings toward concentrating solar power systems operating at 750 °C

Solar selective absorber coating with long-term thermal stability at high temperatures ≥750 °C in air is an important component to reduce the levelized cost of energy (LCOE) of concentrating solar power (CSP) systems toward 50% power efficiency and dispatchable solar electricity. Conventionally, solar spectral selectivity requires multilayer-interference coatings implemented by stringently controlled vacuum deposition, and these coatings degrade significantly at >700 °C in air. Herein, we established a quantitative design approach and demonstrated a proof-of-concept air-stable, manganese–iron oxide nanoparticle (NP)-pigmented solar selective coatings with a high solar absorptance of ~93%, a relatively low thermal emittance of ~52%, and an optical-to-thermal energy conversion efficiency >89% under 1,000× solar concentration at 750 °C toward Generation 3 CSP systems. These coatings demonstrate spectral selectivity using cost-effective spray coating approach, a notable improvement over conventional vacuum-deposited, multilayer solar selective coatings for low-cost, high-efficiency solar thermal receivers. In contrast to the thermal degradation of spectrally non-selective benchmark Pyromark 2500 coatings at 750 °C in air, the solar absorptance of the MnFe 2 O 4 -pigmented coatings on stainless steel 310 (SS 310) substrates is increased to ~92.9% and the optical-to-thermal energy conversion efficiency is improved to 89.7% after serving at 750 °C in air for 700 h. X-ray diffraction results reveal that this improvement is due to the transformation of MnFe 2 O 4 NPs into more thermodynamically stable, non-stoichiometric manganese-rich manganese ferrite and iron-rich manganese–iron oxide phases after 500 h aging at 750 °C. For >1,000 h-endurance testing at 750 °C in air and the subsequent 19 day-night thermal cycling between 750 °C (12 h/cycle) and 25 °C (12 h/cycle) on SS 310 substrates, the thermal degradation is mainly due to the CrO x microflake formation from SS 310 substrates rather than the coatings, which can be suppressed by preoxidizing the surface of SS 310. With lower emittance matrix material and further optimization of pigment NP stoichiometry, concentration, and coating thickness, it is promising to achieve an optimized thermal efficiency ≥92.5% with long-term thermal stability at 750 °C for Generation 3 CSP systems.

14 SOLAR ENERGY↗

DOE OSTI2020

Effect of magnetic field ripple on parallel electron transport during microwave plasma heating in the Proto-MPEX linear plasma device

The Prototype Material Plasma Exposure eXperiment (Proto-MPEX) is a linear plasma device located at Oak Ridge National Laboratory to develop the plasma source concept for the Materials Plasma Exposure eXperiment (MPEX). Recent experiments have demonstrated the heating of electrons in a high-density deuterium plasma (n e ~ 5 × 10 19 m -3 ) via electron Bernstein waves and source plasma production via helicon waves in this linear configuration. Moreover, experimental observations suggest that the magnetic ripple adversely affects the parallel transport of the heated electrons toward the target where material samples are to be exposed to the plasma. In order to understand the transport process during microwave application, a test-particle Monte-Carlo (MC) code has been developed that incorporates the effects of Coulomb collisions, magnetic mirror adiabatic trapping and electron cyclotron interaction via a quasilinear RF heating operator. MC calculations indicate that the absence of 2nd turning points along the trajectory of cyclotron heated electrons significantly reduces adiabatic trapping and maximizes power transport to the Target surface. Thermalization of cyclotron heating electrons is analyzed with the MC code and it is found that for conditions relevant to ProtoMPEX, a significant fraction of the absorbed heating power is coupled to the Target surface via ballistic fast electrons; however, under certain conditions, up to 60% of the absorbed RF power can be dissipated via thermalization of the fast electrons on the background plasma. Results are compared with experimental measurements. Finally, the implications of the results are discussed in the context of the upcoming MPEX device.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

High-Strength, High-Ductility, High Entropy Alloys with High-Efficiency Native Oxide Solar Absorbers for Concentrating Solar Power Systems

This EPSCoR Project has been investigating the synergy between the excellent high-temperature mechanical behavior of FeMnNiAlCr high entropy alloys (HEA) and the high solar absorptance of their native oxides for high efficiency concentrated solar thermal power (CSP) systems working at >700°C. While HEAs have attracted substantial interest in recent years, most investigations have focused on their applications as structural materials rather than functional materials. This EPSCoR project discovered that FeMnNiAlCr HEAs can potentially be applied synergistically as both a structural and functional material for high-efficiency concentrating solar thermal power (CSP) systems working at >700°C. The HEA itself would be used in high-temperature tubing to carry molten salts or supercritical CO 2 , while its surface oxide would act as a high-efficiency solar thermal absorber. With Fe and Mn being the major components in these HEAs (adding up to ~70 at.% of the alloy), these materials are much more cost-effective than the Ni-based superalloys currently being investigated for high-temperature CSP systems. Through this research, these Fe-Mn based HEAs have demonstrated yield strengths 2-3x greater than that of stainless steel at 700°C and a creep lifetime >800 h at 700ºC under a typical CSP tubing mechanical load of 35 MPa. Their Mn-rich surface oxides maintain a high optical-to-thermal conversion efficiency of ~87% under 1000x solar concentration ratio for 20 simulated day-night thermal cycles between 750ºC and room temperature. In preliminary corrosion studies, these HEAs have sustained immersion in unpurified bromide molten salts for 14 days at 750°C with <2% weight loss, in contrast to 70% weight loss from a 316 stainless steel reference. The simultaneous achievement of promising mechanical, optical, and thermochemical properties in this FeMnNiAlCr system opens the door to new applications of HEAs in solar energy harvesting. Partnerships with Ames Laboratory and Oak Ridge National Laboratory (ORNL) also advanced our understanding of the fundamental structure-property relationships through atomic scale material characterization and first-principles computational modeling. The key research results in this project can potentially be extended to other HEAs and their native oxides. In terms of applications, the proposed FeMnNiAlCr HEA/native oxide system could potentially exceed the mechanical and the optical performance of existing tubing and solar coating materials under EERE’s CSP program at lower cost, which also aligns well with the EPSCoR Science and Technology strategies of New Hampshire in boosting the deployment of renewable energy.

14 SOLAR ENERGY↗

NASA NTRS2021

Precise Timing and Phase-resolved Spectroscopy of the Young Pulsar J1617-5055 with NuSTAR

We report on a Nuclear Spectroscopic Telescope Array (NuSTAR) observation of the young, energetic pulsar PSR J1617-5055. Parkes Observatory 3 GHz radio observations of the pulsar (taken about 7 yr before the NuSTAR observations) are also reported here. NuSTAR detected pulsations at a frequency of f ≍ 14.4 Hz (P ≍ 69.44 ms) and, in addition, the observation was long enough to measure the source's frequency derivative, ḟ ≈ -2.8 X10^(-11) Hz/s. We find that the pulsar shows one peak per period at both hard X-ray and radio wavelengths, but that the hard X-ray pulse is broader (having a duty cycle of ~0.7), than the radio pulse (having a duty cycle of ~0.08). Additionally, the radio pulse is strongly linearly polarized. J1617's phase-integrated hard X-ray spectrum is well fit by an absorbed power-law model, with a photon index Γ = 1.59 ± 0.02. The hard X-ray pulsations are well described by three Fourier harmonics, and have a pulsed fraction that increases with energy. We also fit the phase-resolved NuSTAR spectra with an absorbed power-law model in five phase bins and find that the photon index varies with phase from Γ = 1.52 ± 0.03 at phases around the flux maximum to Γ = 1.79 ± 0.06 around the flux minimum. Last, we compare our results with other pulsars whose magnetospheric emission is detected at hard X-ray energies and find that, similar to previous studies, J1617's hard X-ray properties are more similar to the MeV pulsars than the GeV pulsars.

Neutron Stars↗

NASA NTRS2011

Hybrid Power Management-Based Vehicle Architecture

Hybrid Power Management (HPM) is the integration of diverse, state-of-the-art power devices in an optimal configuration for space and terrestrial applications (s ee figure). The appropriate application and control of the various power devices significantly improves overall system performance and efficiency. The basic vehicle architecture consists of a primary power source, and possibly other power sources, that provides all power to a common energy storage system that is used to power the drive motors and vehicle accessory systems. This architecture also provides power as an emergency power system. Each component is independent, permitting it to be optimized for its intended purpose. The key element of HPM is the energy storage system. All generated power is sent to the energy storage system, and all loads derive their power from that system. This can significantly reduce the power requirement of the primary power source, while increasing the vehicle reliability. Ultracapacitors are ideal for an HPM-based energy storage system due to their exceptionally long cycle life, high reliability, high efficiency, high power density, and excellent low-temperature performance. Multiple power sources and multiple loads are easily incorporated into an HPM-based vehicle. A gas turbine is a good primary power source because of its high efficiency, high power density, long life, high reliability, and ability to operate on a wide range of fuels. An HPM controller maintains optimal control over each vehicle component. This flexible operating system can be applied to all vehicles to considerably improve vehicle efficiency, reliability, safety, security, and performance. The HPM-based vehicle architecture has many advantages over conventional vehicle architectures. Ultracapacitors have a much longer cycle life than batteries, which greatly improves system reliability, reduces life-of-system costs, and reduces environmental impact as ultracapacitors will probably never need to be replaced and disposed of. The environmentally safe ultracapacitor components reduce disposal concerns, and their recyclable nature reduces the environmental impact. High ultracapacitor power density provides high power during surges, and the ability to absorb high power during recharging. Ultracapacitors are extremely efficient in capturing recharging energy, are rugged, reliable, maintenance-free, have excellent lowtemperature characteristic, provide consistent performance over time, and promote safety as they can be left indefinitely in a safe, discharged state whereas batteries cannot.

Eichenberg, Dennis J.↗

NASA NTRS1993

Self-mode-locked chromium-doped forsterite laser generates 50-fs pulses

Stable transform-limited (delta nu-delta tau = 0.32) femtosecond pulses with a FWHM of 50 fs were generated from a self-mode-locked chromium-doped forsterite laser. The forsterite laser was synchronously pumped by a CW mode-locked Nd:YAG (82 MHz) laser that generated picosecond pulses (200-300 ps) and provided the starting mechanism for self-mode-locked operation. Maximum output power was 45 mW for 3.9 W of absorbed pumped power with the use of an output coupler with 1 percent transmission. The self-mode-locked forsterite laser was tuned from 1240 to 1270 nm.

Seas, A.↗

NASA NTRS2008

Solar-Terrestrial Coupling Evidenced by Periodic Behavior in Geomagnetic Indexes and the Infrared Energy Budget of the Thermosphere

We examine time series of the daily global power (W) radiated by carbon dioxide (at 15 microns) and by nitric oxide (at 5.3 microns) from the Earth s thermosphere between 100 km and 200 km altitude. Also examined is a time series of the daily absorbed solar ultraviolet power in the same altitude region in the wavelength span 0 to 175 nm. The infrared data are derived from the SABER instrument and the solar data are derived from the SEE instrument, both on the NASA TIMED satellite. The time series cover nearly 5 years from 2002 through 2006. The infrared and solar time series exhibit a decrease in radiated and absorbed power consistent with the declining phase of the current 11-year solar cycle. The infrared time series also exhibits high frequency variations that are not evident in the solar power time series. Spectral analysis shows a statistically significant 9-day periodicity in the infrared data but not in the solar data. A very strong 9-day periodicity is also found to exist in the time series of daily A(sub p) and K(sub p) geomagnetic indexes. These 9-day periodicities are linked to the recurrence of coronal holes on the Sun. These results demonstrate a direct coupling between the upper atmosphere of the Sun and the infrared energy budget of the thermosphere.

Mlynczak, Martin G.↗

DOE OSTI2024

Performance Evaluation of Multi-Vendor Grid-Forming Inverters for Grid-Connected Operation Through Hardware Experimentation: Preprint

Existing real-world projects of GFM inverters that operate in parallel to power grids typically are sized between dozens and a few hundreds Megawatt (MW) scale according to a recent NERC GFM inverter white paper. These large systems are often difficult to evaluate prior to deployments because of their large size. The performance of smaller GFM inverters (dozens to a few hundreds MW) that operate parallel with power grids (distribution systems) is even less understood. There is an opportunity to better understand these systems through hardware testing under controlled laboratory conditions. Therefore, this paper presents the functional performance evaluation tests of multiple (three) commercial GFM inverters when they operate in parallel with the grid through hardware experiments. The goal of these tests is to explore the GFM inverters' functionalities and dynamic response when in parallel with power grids to eventually develop universal specifications for GFM inverters. Both steady state (changing the inverter's frequency and voltage droop) and transient (adding step change in grid's frequency/voltage) tests are performed for each GFM inverter with the same testing circuit and testing protocol. The experimental results indicate the bench-marked performance that: 1) the GFM inverters can be dispatched through frequency and voltage droop intercepts to output the target power when paralleled to the grid; 2) the GFM inverters automatically respond to system frequency and voltage events to output the needed power, however, the GFM inverters all show stability issues when absorbing reactive power from the grid.

grid-forming inverters↗

NASA NTRS1991

Experiment and numerical simulation of RF heating in the Tandem Mirror plasma propulsion device

Recent results of experimental and theoretical studies of ICRF heating of the plasma in the Tendem Mirror rocket are presented. The radial and axial profile of the magnetic field of the wave have been measured, and the data agree with the results from numerical simulation. One very important new finding is that the wave damped when it approached the resonance plane. This is a strong indication of beach heating effect and that RF power is absorbed by the ions in the plasma as expected. This power absorption phenomenon was also further confirmed by the refined analytical study of the wave propagation in a slab model. The electron density in the central cell has been measured by a microwave interferometer. The existence of two types of discharge similar to those of H-alpha emission have also been observed from the density measurements. A preliminary design of a flight system for a 100-day Mars transit has been undertaken. The specific weight for a 10 MW rocket is only 0.04 kg/kW.

Yang, T. F.↗

DOE OSTI2021

Efficient and Reliable Power Takeoff for Ocean Wave Energy Harvesting

The project goal is to significantly improve the current ocean wave energy harvesting through innovative Power Take-off (PTO) design, advanced power electronics, and novel wave capture structures. The objective of the project is to design and demonstrate system-agnostic components for application across multiple MHK systems, and complete component designs, build scaled prototypes, and perform testing and analysis for metric validation of 25% increase in component rating/per unit cost and 50% reduction in failure rate. The major innovation of the PTO is the Mechanical Motion Rectifier (MMR) mechanism that rectifies the bi-directional oscillatory motion of the input from waves into a steady unidirectional rotation output to directly drive the electrical generator. Through this mechanism, the efficiency and the fatigue life of the PTO can be significantly improved to benefit the energy absorption and lifespan of the wave energy converters (WEC). During the period of performance, the component and system design are completed, the scaled prototypes are developed and performed testing. It is validated that the 25% increase in a component rating/per unit cost. The 50% reduction in failure rate is not directly validated by experiments, however, it can be explained qualitatively with analysis. Besides, 8 journal articles, 13 conference proceedings, 1 patent, 3 Master thesis and two Ph.D. dissertations are published based on the work related to this project. The list of all the publications can be found at the end of the project as an appendix. Over 30 students and postdocs were trained through this project. Three prototypes of 100W and 500W WECs and 10KW PTO were designed, built, and tested in ocean wave tank and using the NREL dynamometer. This project demonstrated 50-80% PTO efficiency, 90-98% power electronics efficiency, up to 66% capture width ratio in irregular waves, and 34% overall efficiency in regular waves.

16 TIDAL AND WAVE POWER↗

DOE OSTI2024

Performance Evaluation of Multi-Vendor Grid-Forming Inverters for Grid-Connected Operation Through Hardware Experimentation

This paper presents the functional performance evaluation tests of multiple (three) commercial grid-forming (GFM) inverters when they operate in parallel with the grid through hardware experiments. The goal of these tests is to explore and benchmark the GFM inverters' functionalities and dynamic response when they are operated in parallel with power grids. Both steady-state (changing the inverter's frequency and voltage droop) and transient (adding step changes to grid's frequency/voltage) tests are performed for each GFM inverter with the same testing circuit and testing protocol. The key findings are summarized as follows: 1) The GFM inverters can be dispatched through frequency and voltage droop intercepts to output the target power; and 1) the GFM inverters automatically respond to system frequency and voltage events to output the needed power; 3) all the GFM inviters shows stability issues when absorbing reactive power from the grid.

frequency droop↗

NASA NTRS1991

Spectral performance of monolithic holmium and thulium lasers

Fabry-Perot resonators have been used to demonstrate single-mode lasing of holmium and neodymium YAG. The previous demonstration in the holmium laser required TE cooling the crystal to -15 C in order to achieve threshold. The present study extends that result, demonstrating +25 C operation in a 1-mm thick plano/plano resonator. The experimental configuration of lasing both the holmium and thulium lasers used a 500-mW diode laser which was collimated, circularized, and focused into a beam radius of 60 microns. The single-frequency lasing spectrum of the holmium laser is shown. By adjusting the mirror reflectivity, the ability to control the laser's wavelength is demonstrated. This laser operated with 11 mW of optical power, a 57-percent slope efficiency, and 120-mW threshold vs absorbed diode power laser for the 60-micron beam radius. The thulium laser operated very efficiently at room temperature, but on seven longitudinal modes. The Tm:TAG laser exhibits typical characteristics of spatial hole burning not seen in the Ho:Tm:YAG for flat/flat resonators.

Storm, Mark E.↗

NASA NTRS1939

Tandem Air Propellers - II

Tests of three-blade, adjustable-pitch counterrotating tandem model propellers, adjusted to absorb equal power at maximum efficiency of the combination, were made at Stanford University. The aerodynamic characteristics, for blade-angle settings of 15, 25, 35, 45, 55, and 65 degrees at 0.75R of the forward propeller and for diameters spacings of 8-1/2, 15 and 30% were compared with those of three-blade and six-blade propellers of the same blade form. It was found that, in order to realize the condition of equal power at maximum efficiency, the blade angles for the rear propeller must be generally less than for the forward propeller, the difference increasing the blade angle. The tests showed that, at maximum efficiency, the tandem propellers absorb about double the power of three-blade propellers and about 8% more power than six-blade propellers having the pitch of the forward propeller of the tandem combination. The maximum efficiency of the tandem propellers was found to be from 2-15% greater than for six-blade propellers, the difference varying directly with blade angle. It was also found that the maximum efficiency of the tandem propellers was greater than that of a three-blade propeller for blade angles at 0.75R of 25 degrees or more. The difference in maximum efficiency again varied directly with blade angle, being about 9% for 65 degrees at 0.75R.

Lesley, E. P.↗

DOE OSTI2020

Laser and thermooptical characteristics of a laser head based on a thin Yb : YAG slab

Amplification and thermally induced phase distortions in a cw pumped laser head with an active element in the form of a thin Yb : YAG slab are experimentally studied. Lasing characteristics of an emitter based on this laser head are examined. Laser radiation is obtained with an average power of 32 W and a slope efficiency with respect to the absorbed pump power η = 68 %. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2021

Ultrafast optical switching and power limiting in intersubband polaritonic metasurfaces

Highly nonlinear optical materials with fast third-order nonlinear optical response are crucial for the operation of all-optical photonic devices, such as switches for signal processing and computation, power limiters, and saturable absorbers. The nonlinear response of traditional optical materials is weak, thus requiring large light intensities to induce significant changes in their properties. Here we show that optical control of the coupling rate in subwavelength patch antennas coupled to intersubband transitions in multi-quantum-well semiconductor heterostructures can provide a giant third-order nonlinear response, on the order of 3.4 × <#comment/> 10 − <#comment/> 13 m 2 / V 2 , with a response time < <#comment/> 2 p s . We utilize this effect to realize intersubband polaritonic metasurfaces and demonstrate their operation as highly nonlinear saturable and reverse saturable absorbers, enabling optical power limiters and other elements for all-optical modulation and control. Our approach enables a plethora of compact, low-power, highly nonlinear devices with spectral, temporal, and structured wavefront responses tailored by design.

Mann, Sander A. (ORCID:0000000277420615)↗

NASA NTRS2012

Energy Budgets of the Giant Planets and Titan

As a fundamental property, the energy budget affects many aspeCts of planets and their moons, such as thermal structure, meteorology, and evolution. We use the observations from two Cassini spectrometers (i.e., CIRS and VIMS) to explore one important component of the energy budget the total emitted power of Jupiter, Saturn, and Titan (Li et al., 2010, 2011, 2012). Key results are: (1) The Cassini observations precisely measure the global-average emitted power of three bodies: 14.l0+/-0.03 Wm(exp -2), 4.952+/-0.035 Wm(exp -2), and 2.834+/-0.012 Wm(exp -2) for Jupiter, Saturn, and Titan, respectively. (2) The meridional distribution of emitted power displays a significant asymmetry between the northern and southern hemispheres on Jupiter and Saturn. On Titan, the meridional distribution of emitted power is basically symmetric around the equator. (3) Comparing with the Voyager measurements, the new Cassini observations reveal a significant temporal variation of emitted power on both Jupiter and Saturn: i) The asymmetry between the two hemisphere shown in the Cassini epoch (2000-2010) is not present in the Voyager epoch (1979-1980); and ii) From the Voyager epoch to the Cassini epoch, the global-average emitted power appeared to increase by approx 3.8% for Jupiter and approx 6.4% for Saturn. (4) Together with previous measurements of the absorbed solar power on Titan, the new Cassini measurements of emitted power provide the first observational evidence of the global energy balance on Titan. The uncertainty in the previous measurements of absorbed solar energy places an upper limit on its energy imbalance of 6.0% on Titan. The exploration of emitted power is the first part of a series of studies examining the temporal variability of the energy budget on the giant planets and Titan. Currently, We are measuring the absorbed solar energy in order to determine new constraints on the energy budgets of Jupiter, Saturn, and Titan.

Liming, Li↗