Search NASA⌕ Search

SEARCH · Search NASA

Results for “acoustic tones”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Control of Inflow Distortion in a Scarf Inlet

The scarf inlet has the potential to reduce aircraft inlet noise radiation to the ground by reflecting it into the space above the engine. Without forward motion of the engine, the non-symmetry of the inlet causes inflow distortion which generates noise that is greater than the noise reduction of the scarf. However, acoustic evaluations of aircraft engines are often done on static test stands. A method to reduce inflow distortion by boundary layer suction is proposed and evaluated using a model of a high bypass ratio engine located in an anechoic chamber. The design goal of the flow control system is to make the inflow to the inlet circumferentially uniform and to eliminate reversed flow. This minimizes the inflow distortion and allows for acoustic evaluation of the scarf inlet on a static test stand. The inlet boundary layer suction effectiveness is evaluated both by aerodynamic and by acoustic measurements. Although the design goal is not met, the control system is found to have a beneficial effect on the engine operation, reducing blade stall and speed variation. This is quantified by two acoustic benefits, reduction both of the variability of tone noise and of the low frequency wideband noise due to the inflow distortion. It is felt that a compromise in the manufacture of the control hardware contributes to the inability of the control system to perform as expected from the analysis. The control system with sufficient authority is felt to have the potential to permit reliable acoustic testing in a static configuration of engines with non-symmetric inlets. Because the control system can improve operation of the engine, it may also have the potential to reduce noise and vibration and enhance engine longevity during low speed ground operations in the terminal area.

Gerhold, Carl H.↗
NASA NTRS2012

Advanced Jet Noise Exhaust Concepts in NASA's N+2 Supersonics Validation Study and the Environmentally Responsible Aviation Project's Upcoming Hybrid Wing Body Acoustics Test

Acoustic and flow-field experiments were conducted on exhaust concepts for the next generation supersonic, commercial aircraft. The concepts were developed by Lockheed Martin (LM), Rolls-Royce Liberty Works (RRLW), and General Electric Global Research (GEGR) as part of an N+2 (next generation forward) aircraft system study initiated by the Supersonics Project in NASA s Fundamental Aeronautics Program. The experiments were conducted in the Aero-Acoustic Propulsion Laboratory at the NASA Glenn Research Center. The exhaust concepts presented here utilized lobed-mixers and ejectors. A powered third-stream was implemented to improve ejector acoustic performance. One concept was found to produce stagnant flow within the ejector and the other produced discrete-frequency tones (due to flow separations within the model) that degraded the acoustic performance of the exhaust concept. NASA's Environmentally Responsible Aviation (ERA) Project has been investigating a Hybrid Wing Body (HWB) aircraft as a possible configuration for meeting N+2 system level goals for noise, emissions, and fuel burn. A recently completed NRA led by Boeing Research and Technology resulted in a full-scale aircraft design and wind tunnel model. This model will be tested acoustically in NASA Langley's 14-by 22-Foot Subsonic Tunnel and will include dual jet engine simulators and broadband engine noise simulators as part of the test campaign. The objectives of the test are to characterize the system level noise, quantify the effects of shielding, and generate a valuable database for prediction method development. Further details of the test and various component preparations are described.

Henderson, Brenda S.↗
NASA NTRS1985

Propeller aircraft interior noise model: User's manual for computer program

A computer program entitled PAIN (Propeller Aircraft Interior Noise) has been developed to permit calculation of the sound levels in the cabin of a propeller-driven airplane. The fuselage is modeled as a cylinder with a structurally integral floor, the cabin sidewall and floor being stiffened by ring frames, stringers and floor beams of arbitrary configurations. The cabin interior is covered with acoustic treatment and trim. The propeller noise consists of a series of tones at harmonics of the blade passage frequency. Input data required by the program include the mechanical and acoustical properties of the fuselage structure and sidewall trim. Also, the precise propeller noise signature must be defined on a grid that lies in the fuselage skin. The propeller data are generated with a propeller noise prediction program such as the NASA Langley ANOPP program. The program PAIN permits the calculation of the space-average interior sound levels for the first ten harmonics of a propeller rotating alongside the fuselage. User instructions for PAIN are given in the report. Development of the analytical model is presented in NASA CR 3813.

Wilby, E. G.↗
DOE OSTI2022

The effect of simultaneous exposure on the attention selection and integration of segments and lexical tones by Urdu-Cantonese bilingual speakers

In the perceptual learning of lexical tones, an automatic and robust attention-to-phonology system enables native tonal listeners to adapt to acoustically non-optimal speech, such as phonetic conflicts in daily communications. Previous tone research reveals that non-native listeners who do not linguistically employ lexical tones in their mother tongue may find it challenging to attend to the tonal dimension or integrate it with the segmental features. However, it is unknown whether the attentional interference initially caused by a maternal attentional system would continue influencing the non-optimal tone perception for simultaneous bilingual teenagers. From an endpoint in the age of language acquisition, we investigate whether the tone-specific attention mechanism developed by the Urdu-Cantonese simultaneous bilinguals is automatic enough to assist them in adapting to a phonetically-conflicting environment. Three groups of teenagers engaged in a four-condition ABX task: Urdu-Cantonese simultaneous bilinguals, Cantonese native listeners, and Urdu-speaking, late learners of Cantonese. The results showed that although the simultaneous bilinguals could phonologically process Cantonese tones in a Cantonese-like way under a conflict-free listening condition, they still failed in adapting to the phonetic conflicts, especially the segment-induced ones. It thus demonstrated that the simultaneous exposure and years of regular education in Hong Kong local schools still could not automatically guarantee simultaneous bilingual processing of Cantonese tones. In interpreting the findings, it hypothesized that, except for simultaneous exposure, the development of a tone-specific attention mechanism is also likely to be L1-inhibitory, tone experience-driven, and language-specific for simultaneous bilinguals.

Ning, Jinghong↗
NASA NTRS1996

Active Noise Control of Low Speed Fan Rotor-Stator Modes

This report describes the Active Noise Cancellation System designed by General Electric and tested in the NASA Lewis Research Center's 48 inch Active Noise Control Fan. The goal of this study was to assess the feasibility of using wall mounted secondary acoustic sources and sensors within the duct of a high bypass turbofan aircraft engine for active noise cancellation of fan tones. The control system is based on a modal control approach. A known acoustic mode propagating in the fan duct is cancelled using an array of flush-mounted compact sound sources. Controller inputs are signals from a shaft encoder and a microphone array which senses the residual acoustic mode in the duct. The canceling modal signal is generated by a modal controller. The key results are that the (6,0) mode was completely eliminated at 920 Hz and substantially reduced elsewhere. The total tone power was reduced 9.4 dB. Farfield 2BPF SPL reductions of 13 dB were obtained. The (4,0) and (4,1) modes were reduced simultaneously yielding a 15 dB modal PWL decrease. Global attenuation of PWL was obtained using an actuator and sensor system totally contained within the duct.

Sutliff, Daniel L.↗
NASA NTRS1983

Tone generation by rotor-downstream strut interaction

A JT15D fan stage was acoustically tested in the NASA Lewis anechoic chamber as part of the joint Lewis-Langley Research Center investigation of flight simulation techniques and flight effects using the JT15D engine as a common test vehicle. Suspected rotor-downstream support strut interaction was confirmed through the use of simulated support struts which were tested at three axial rotor-strut spacings. Tests were also performed with the struts removed. Inlet boundary layer suction in conjuction with an inflow control device was also explored. The removal of the boundary layer reduced the fan fundamental tone levels suggesting that the mounting and mating of such a device to the nacelle requires careful attention. With the same inflow control device installed good acoustic agreement was shown between the engine on an outdoor test stand and the fan in the anechoic chamber.

Woodward, R. P.↗
NASA NTRS1983

Tone generation by rotor-downstream strut interaction

A JT15D fan stage was acoustically tested in the NASA Lewis anechoic chamber as part of the joint Lewis-Langley Research Center investigation of flight simulation techniques and flight effects using the JT15D engine as a common test vehicle. Suspected rotor-downstream support strut interaction was confirmed through the use of simulated support struts which were tested at three axial rotor-strut spacings. Tests were also performed with the struts removed. Inlet boundary layer suction in conjunction with an inflow control device was also explored. The removal of the boundary layer reduced the fan fundamental tone levels suggesting that the mounting and mating of such a device to the nacelle requires careful attention. With the same inflow control device installed good acoustic agreement was shown between the engine on an outdoor test stand and the fan in the anechoic chamber.

Woodward, R. P.↗
NASA NTRS1996

Active Control of Fan Noise: Feasibility Study: Active Fan Noise Cancellation in the NASA Lewis Active Noise Control Fan Facility - Volume 3

This report describes the Active Noise Cancellation (ANC) System designed by General Electric and tested in the NASA Lewis Research Center's (LERC) 48 inch Active Noise Control Fan (ANCF). The goal of this study is to assess the feasibility of using wall mounted secondary acoustic sources and sensors within the duct of a high bypass turbofan aircraft engine for global active noise cancellation of fan tones. The GE ANC system is based on a modal control approach. A known acoustic mode propagating in the fan duct is canceled using an array of flush-mounted compact sound sources. The canceling modal signal is generated by a modal controller. Inputs to the controller are signals from a shaft encoder and from a microphone array which senses the residual acoustic mode in the duct. The key results are that the (6,0) was completely eliminated at the 920 Hz design frequency and substantially reduced elsewhere. The total tone power was reduced 6.8 dB (out of a possible 9.8 dB). Farfield reductions of 15 dB (SPL) were obtained. The (4,0) and (4,1) modes were reduced simultaneously yielding a 15 dB PWL decrease. The results indicate that global attenuation of PWL at the target frequency was obtained in the aft quadrant using an ANC actuator and sensor system totally contained within the duct. The quality of the results depended on precise mode generation. High spillover into spurious modes generated by the ANC actuator array caused less than optimum levels of PWL reduction. The variation in spillover is believed to be due to calibration procedure, but must be confirmed in subsequent tests.

Pla, Frederic G.↗
NASA NTRS2015

Modeling of Broadband Liners Applied to the Advanced Noise Control Fan

The broadband component of fan noise has grown in relevance with an increase in bypass ratio and incorporation of advanced fan designs. Therefore, while the attenuation of fan tones remains a major factor in engine nacelle acoustic liner design, the simultaneous reduction of broadband fan noise levels has received increased interest. As such, a previous investigation focused on improvements to an established broadband acoustic liner optimization process using the Advanced Noise Control Fan (ANCF) rig as a demonstrator. Constant-depth, double-degree of freedom and variable-depth, multi-degree of freedom liner designs were carried through design, fabrication, and testing. This paper addresses a number of areas for further research identified in the initial assessment of the ANCF study. Specifically, incident source specification and uncertainty in some aspects of the predicted liner impedances are addressed. This information is incorporated in updated predictions of the liner performance and comparisons with measurement are greatly improved. Results illustrate the value of the design process in concurrently evaluating the relative costs/benefits of various liner designs. This study also provides further confidence in the integrated use of duct acoustic propagation/radiation and liner modeling tools in the design and evaluation of novel broadband liner concepts for complex engine configurations.

Nark, Douglas M.↗
NASA NTRSDate not supplied

Update on Electric Motor Noise

Electric motors like those used in concept Advanced Air Mobility vehicles generate noise relevant to the acoustic profile of those vehicles. This work presents ongoing efforts to study, understand, and predict the noise generated by these types of motors. Efforts to perform experimental and simulation investigations of motor vibration modes are presented. Then recent acoustic measurements of operating motors and the resonant tones they generate is discussed. Lastly an update of ongoing efforts to measure real world vehicles is provided.

Electric motor noise↗
NASA NTRS1974

Acoustic and aerodynamic performance of a 1.83 meter (6 foot) diameter 1.2 pressure ratio fan (QF-6)

A 1.2-pressure-ratio, 1.83-meter-(6-ft-) diameter experimental fan stage with characteristics suitable for use in STOL aircraft engines was tested for acoustic and aerodynamic performance. The design incorporated features for low noise, including absence of inlet guide vanes, low rotor-blade-tip speed, low aerodynamic blade loading, and long axial spacing between the rotor and stator rows. The stage was run with four nozzles of different area. The perceived noise along a 152.4 meter (500-ft) sideline was rear-quadrant dominated with a maximum design-point level of 103.9 PNdb. The acoustic 1/3-octave results were analytically separated into broadband and pure-tone components. It was found that the stage noise levels generally increase with a decrease in nozzle area, with this increase observed primarily in the broadband noise component. A stall condition was documented acoustically with a 90-percent-of-design-area nozzle.

Woodward, R. P.↗
NASA NTRS1990

Impingement tones of large aspect ratio supersonic rectangular jets

The frequency structure of large aspect ratio jet impingement tones is analyzed. Feedback loops consisting of downstream propagating instability waves of the jet flow and upstream propagating acoustic waves from the wall to the nozzle lip produce as many as 20 or more tones when a supersonic rectangular jet of large aspect ratio is directed normal on a wall. It is seen that there are only two basic tones. The basic tone of the lower frequency is associated with a symmetric instability feedback mode of the jet, while that of the higher frequency is associated with an antisymmetric instability feedback mode. The remaining tones are combination tones of the two basic frequencies and their harmonics. It is determined that the measured basic impingement tone frequencies fall in the theoretical permissible frequency bands over a wide range of jet Mach number.

Tam, Christopher K. W.↗
NASA NTRS1986

Recent advances in aeroacoustics

The state of the art in theoretical and numerical models and experimentation on broadband noise propagation from high speed aircraft components such as jets and helicopter blades is detailed. Attention is given to noise produced by jets, shear layers and turbulence and to the acoustic properties of rotors. The generation and propagation of acoustic noise are discussed in terms of the evolution of concepts for flow-tone generation to include hydrodynamic instabilities. Consideration is also given to techniques for experimental studies and theoretical models for nonlinear features of acoustic propagation of broadband noise and acoustic propagation in partially-choked or soft-walled ducts.

Krothapalli, A.↗
NASA NTRS2000

Direct Numerical Simulation of Automobile Cavity Tones

The Navier Stokes equation is solved computationally by the Dispersion-Relation-Preserving (DRP) scheme for the flow and acoustic fields associated with a laminar boundary layer flow over an automobile door cavity. In this work, the flow Reynolds number is restricted to R(sub delta*) < 3400; the range of Reynolds number for which laminar flow may be maintained. This investigation focuses on two aspects of the problem, namely, the effect of boundary layer thickness on the cavity tone frequency and intensity and the effect of the size of the computation domain on the accuracy of the numerical simulation. It is found that the tone frequency decreases with an increase in boundary layer thickness. When the boundary layer is thicker than a certain critical value, depending on the flow speed, no tone is emitted by the cavity. Computationally, solutions of aeroacoustics problems are known to be sensitive to the size of the computation domain. Numerical experiments indicate that the use of a small domain could result in normal mode type acoustic oscillations in the entire computation domain leading to an increase in tone frequency and intensity. When the computation domain is expanded so that the boundaries are at least one wavelength away from the noise source, the computed tone frequency and intensity are found to be computation domain size independent.

Kurbatskii, Konstantin↗
NASA NTRS2000

Acoustic and Aerothermal Performance Test of the Axisymmetric Coannular Ejector Nozzle: Acoustic Performance - Volume 2

Acoustic and propulsion performance testing of a model-scale Axisymmetric Coannular Ejector nozzle was conducted in the Boeing Low-speed Aeroacoustic Facility. This nozzle is a plug nozzle with an ejector design to provide aspiration of about 20% of the engine flow. A variety of mixing enhancers were designed to promote mixing of the engine and the aspirated flows. These included delta tabs, tone-injection rods, and wheeler ramps. This report addresses the acoustic aspects of the testing. The spectral characteristics of the various configurations of the nozzle are examined on a model-scale basis. This includes indentifying particular noise sources contributing to the spectra and the data are projected to full-scale flyover conditions to evaluate the effectiveness of the nozzle, and of the various mixing enhancers, on reducing the Effective Perceived Noise Levels.

Herkes, William↗
NASA NTRS1992

Measurements of fluctuating pressure in a rectangular cavity in transonic flow at high Reynolds numbers

An experiment was performed in the Langley 0.3 meter Transonic Cryogenic Tunnel to study the internal acoustic field generated by rectangular cavities in transonic and subsonic flows and to determine the effect of Reynolds number and angle of yaw on the field. The cavity was 11.25 in. long and 2.50 in. wide. The cavity depth was varied to obtain length-to-height (l/h) ratios of 4.40, 6.70, 12.67, and 20.00. Data were obtained for a free stream Mach number range from 0.20 to 0.90, a Reynolds number range from 2 x 10(exp 6) to 100 x 10(exp 6) per foot with a nearly constant boundary layer thickness, and for two angles of yaw of 0 and 15 degs. Results show that Reynolds number has little effect on the acoustic field in rectangular cavities at angle of yaw of 0 deg. Cavities with l/h = 4.40 and 6.70 generated tones at transonic speeds, whereas those with l/h = 20.00 did not. This trend agrees with data obtained previously at supersonic speeds. As Mach number decreased, the amplitude, and bandwidth of the tones changed. No tones appeared for Mach number = 0.20. For a cavity with l/h = 12.67, tones appeared at Mach number = 0.60, indicating a possible change in flow field type. Changes in acoustic spectra with angle of yaw varied with Reynolds number, Mach number, l/h ratios, and acoustic mode number.

Tracy, M. B.↗
NASA NTRS1974

Acoustic results of supersonic tip speed fan blade modification

A supersonic tip speed single stage fan was modified with the intent of reducing multiple pure tone (MPT) or buzz saw noise. There were three modifications to the blades from the original design. The modifications to the blade resulted in an increase in cascade throat area causing the shock to start at a lower corrected fan speed. The acoustic results without acoustically absorbing liners showed substantial reduction in multiple pure tone levels. However, an increase in the blade passing frequency noise at takeoff fan speed accompanied the MPT reduction. The net result however, was a reduction in the maximum 1000-foot (304.8 m) altitude level flyover PNL. For the case with acoustic treatment in the inlet outer wall, the takeoff noise increased relative to an acoustically treated baseline. This was largely due to the increased blade passing frequency noise which was not effectively reduced by the liner.

Jutras, R. R.↗
NASA NTRS1977

Inlet turbulence and fan noise measured in an anechoic wind tunnel and statically with an inlet flow control device

Turbulence and acoustic measurements were taken in the NASA-Lewis anechoic wind tunnel - a facility which has demonstrated the blade passage tone cutoff phenomena with forward velocity. Turbulence data were taken in a subsonic inlet at various fan speeds under static and forward velocity conditions. A honeycomb/screen flow control device was placed over the inlet during static tests to modify the inflow in an attempt to simulate flight conditions. Acoustic levels of the blade passage tone along with transverse turbulence intensities were reduced with forward velocity. The flow control device reduced the blade passage tone to an intermediate level between those levels associated with static and forward velocity operation.

Shaw, L. M.↗