Search NASA⌕ Search

SEARCH · Search NASA

Results for “adhesive bonding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

LARC-13 polyimide adhesive bonding

The development of an addition-curing polyimide adhesive suitable for low pressure bonding without the generation of volatiles during cure is reported. LARC-13 is designed for bonding of polyimide matrix composites and of titanium to be used above 500 F, and is based on an oligomeric bis-nadimide which allows its processing at 50 psi or less, making it suitable for the bonding of fragile honeycomb sandwich structures. Few volatiles are evolved during its cure allowing large enclosed structures to be bonded, and it has high room and elevated temperature strengths and good strength retention after short terms up to 1100 F. LARC-13 was successfully used to bond the outer and inner skins of a polyimide/graphite wing shear panel for 500 F use, and for a short-term exposure up to 1100 F. Preparation of the adhesive, bonding, aging, and testing of lap shear and honeycomb samples are discussed.

Saint Clair, T. L.↗
NASA NTRS1982

The effects of inherent flaws on the time and rate dependent failure of adhesively bonded joints

Inherent flaws, as well as the effects of rate and time, are shown by tests on viscoelastic adhesive-bonded single lap joints to be as critical in joint failure as environmental and stress concentration effects, with random inherent flaws and loading rate changes resulting in an up to 40% reduction in joint strength. It is also found that the asymptotic creep stress, below which no delayed failure may occur, may under creep loading be as much as 45% less than maximum adhesive strength. Attention is given to test results for the case of titanium-LARC-3 adhesive single-lap specimens.

Sancaktar, E.↗
NASA NTRS1992

Effect of service environments on adhesively bonded joints in composite structures

The models employed in the present computational methods for evaluating severe service-environment effects on adhesively bonded joints in composites are based on composite analyses and structural mechanics, encompassing nonlinear environmental degradation. The methods are demonstrated for the case of a butt joint with a single doubler, subjected to the environmental effects as well as static and cyclic loads. The highest joint strength is noted to be required in the case of cyclic loads and hygrothermal service environments; margins of safety for adhesive material stresses decline rapidly in such cases.

Singhal, S. N.↗
DOE OSTI2024

Exploring Failure of Adhesively-Bonded Joints with Different Void Sizes at the Same Void Volume Fraction through A Micro-scale Numerical Modeling

This paper studied the effects of void sizes on the failure behavior of adhesively-bonded materials under global shear via micro-scale computational modeling. The numerical results indicate that large void sizes with increased distances between them at the same void volume fraction can alleviate the reduced joint strength of a weaker adherend-adhesive interface caused by interfacial voids. However, this is not the case for an adherend-adhesive interface with the interfacial tensile strength being sufficiently higher than the adhesive strength, showing the negligible effect on the joint strength due to various void sizes and the amount of interfacial voids. This preliminary investigation provides insightful information for scaling up the void size in the macro-scale computational modeling of joints, and enhances the understanding of the micro-mechanical adhesion in adherend-adhesive interfaces with different levels of bonding.

Qiao, Yao↗
NASA NTRS1968

Method of disjoining adhesively bonded electronic cordwood modules

Embedment of resistive heating elements in a cordwood module used for packaging electronic components, facilitates separation of the adhesive bond between the module, and metal heat sink and the potting material without damaging the components. Electrical power applied to the elements causes breakdown of bonding material.

Sacramone, P. J.↗
NASA NTRS1992

Preliminary Design Of Adhesively Bonded Composite Joints

Joints symmetrical and long enough to withstand cyclic loads and hygrothermal effects. Step-by-step procedure for preliminary design of adhesively bonded joints between laminated fiber-reinforced-matrix composite bars based on simplified methods for prediction of microstresses and local strengths, including interlaminar strengths. Involves approximate calculations of stresses in various components of joint. Includes calculations to determine such critical parameters as minimum length, maximum shear stress in adhesive, and peeloff stress. Deleterious effects of cyclic loading, increased temperature, and humidity also taken into account.

Chamis, C. C.↗
NASA NTRS1989

Effect of bond thickness on fracture and fatigue strength of adhesively bonded composite joints

An experimental investigation of composite to composite bonded joints was undertaken to study the effect of bond thickness on debond growth rate under cyclic loading and critical strain energy release rate under static loading. Double cantilever beam specimens of graphite/epoxy adherends bonded with EC 3445 were tested under mode I loading. A different behavior of fracture and fatigue strength was observed with variation of bondline thickness.

Mall, S.↗
NASA NTRS1981

Analysis of interface cracks in adhesively bonded lap shear joints, part 4

Conservation laws of elasticity for nonhomogeneous materials were developed and were used to study the crack behavior in adhesively bonded lap shear joints. By using these laws and the fundamental relationships in fracture mechanics of interface cracks, the problem is reduced to a pair of linear algebraic equations, and stress intensity solutions can be determined directly by information extracted from the far field. The numerical results obtained show that: (1) in the lap-shear joint with a given adherend, the opening-mode stress intensity factor, (K sub 1) is always larger than that of the shearing-mode (K sub 2); (2) (K sub 1) is not sensitive to adherent thickness abut (K sub 2) increases rapidly with increasing thickness; and (3) (K sub 1) and (K sub 2) increase simultaneously as the interfacial crack length increases.

Wang, S. S.↗
NASA NTRS2007

A Semi-Analytical Method for Determining the Energy Release Rate of Cracks in Adhesively-Bonded Single-Lap Composite Joints

A semi-analytical method for determining the strain energy release rate due to a prescribed interface crack in an adhesively-bonded, single-lap composite joint subjected to axial tension is presented. The field equations in terms of displacements within the joint are formulated by using first-order shear deformable, laminated plate theory together with kinematic relations and force equilibrium conditions. The stress distributions for the adherends and adhesive are determined after the appropriate boundary and loading conditions are applied and the equations for the field displacements are solved. Based on the adhesive stress distributions, the forces at the crack tip are obtained and the strain energy release rate of the crack is determined by using the virtual crack closure technique (VCCT). Additionally, the test specimen geometry from both the ASTM D3165 and D1002 test standards are utilized during the derivation of the field equations in order to correlate analytical models with future test results. The system of second-order differential field equations is solved to provide the adherend and adhesive stress response using the symbolic computation tool, Maple 9. Finite element analyses using J-integral as well as VCCT were performed to verify the developed analytical model. The finite element analyses were conducted using the commercial finite element analysis software ABAQUS. The results determined using the analytical method correlated well with the results from the finite element analyses.

Yang, Charles↗
NASA NTRS1989

Adhesive bond evaluation using phase sensitive detection techniques

Quadrature phase detection techniques have been used to monitor the amplitude and phase of a toneburst ultrasonic wave normally reflected from adhesively-bonded steel/rubber interface. The measured phase change values of the reflected signals were found to correlate with variations in sample preparation. It was determined that measured phase shift changes were larger for samples with weaker bonds as manifested by smaller measured values of the applied tensile loads at failure. A model calculation which incorporates the concept of interfacial strength into the usual problem of wave propagation in multi-layered isotropic elastic media was used to deduce a bond-quality parameter from an experimentally measured phase shift.

Smith, Alphonso C.↗
NASA NTRS2006

Active Metal Brazing and Adhesive Bonding of Titanium to C/C Composites for Heat Rejection System

Robust assembly and integration technologies are critically needed for the manufacturing of heat rejection system (HRS) components for current and future space exploration missions. Active metal brazing and adhesive bonding technologies are being assessed for the bonding of titanium to high conductivity Carbon-Carbon composite sub components in various shapes and sizes. Currently a number of different silver and copper based active metal brazes and adhesive compositions are being evaluated. The joint microstructures were examined using optical microscopy, and scanning electron microscopy (SEM) coupled with energy dispersive spectrometry (EDS). Several mechanical tests have been employed to ascertain the effectiveness of different brazing and adhesive approaches in tension and in shear that are both simple and representative of the actual system and relatively straightforward in analysis. The results of these mechanical tests along with the fractographic analysis will be discussed. In addition, advantages, technical issues and concerns in using different bonding approaches will also be presented.

Singh, M.↗
NASA NTRS1984

Rapid adhesive bonding concepts for specimen and panel fabrication and field repair

The NASA Langley Research Center has developed bonding concepts for aerospace composite materials which employ induction heating to directly apply heat to the bond line and/or adherends without simultaneously heating the entire structure, supports, and fixtures of a bonding assembly. These methods have demonstrated bonding process time reductions of two to three orders of magnitude, by comparison with conventional press molding. Attention is presently given to rapid adhesive bonding for lap shear specimens for aerospace panel bonding or field repair, as well as for the field repair requirements of metallic and advanced polymeric matrix composite structures.

Stein, B. A.↗
NASA NTRS2012

Adhesive-Bonded Composite Joint Analysis with Delaminated Surface Ply Using Strain-Energy Release Rate

This paper presents an analytical model to determine the strain energy release rate due to an interlaminar crack of the surface ply in adhesively bonded composite joints subjected to axial tension. Single-lap shear-joint standard test specimen geometry with thick bondline is followed for model development. The field equations are formulated by using the first-order shear-deformation theory in laminated plates together with kinematics relations and force equilibrium conditions. The stress distributions for the adherends and adhesive are determined after the appropriate boundary and loading conditions are applied and the equations for the field displacements are solved. The system of second-order differential equations is solved to using the symbolic computation tool Maple 9.52 to provide displacements fields. The equivalent forces at the tip of the prescribed interlaminar crack are obtained based on interlaminar stress distributions. The strain energy release rate of the crack is then determined by using the crack closure method. Finite element analyses using the J integral as well as the crack closure method are performed to verify the developed analytical model. It has been shown that the results using the analytical method correlate well with the results from the finite element analyses. An attempt is made to predict the failure loads of the joints based on limited test data from the literature. The effectiveness of the inclusion of bondline thickness is justified when compared with the results obtained from the previous model in which a thin bondline and uniform adhesive stresses through the bondline thickness are assumed.

Chadegani, Alireza↗
NASA NTRS1982

Adhesive-Bonded Tab Attaches Thermocouples to Titanium

Mechanical strength of titanium-alloy structures that support thermocouples is preserved by first spotwelding thermocouples to titanium tabs and then attaching tabs to titanium with a thermosetting adhesive. In contrast to spot welding, a technique previously used for thermocouples, fatigue strength of the titanium is unaffected by adhesive bonding. Technique is also gentler than soldering or attaching thermocouples with a tap screw.

Cook, C. F.↗
NASA NTRS2003

Shearography for Non-destructive Inspection with applications to BAT Mask Tile Adhesive Bonding and Specular Surface Honeycomb Panels

The applicability of shearography techniques for non-destructive evaluation in two unique application areas is examined. In the first application, shearography is used to evaluate the quality of adhesive bonds holding lead tiles to the B.4T gamma ray mask for the NASA Swift program. Using a vibration excitation, the more poorly bonded tiles are readily identifiable in the shearography image. A quantitative analysis is presented that compares the shearography results with a destructive pull test measuring the force at bond failure. The second application is to evaluate the bonding between the skin and core of a honeycomb structure with a specular (mirror-like) surface. In standard shearography techniques, the object under test must have a diffuse surface to generate the speckle patterns in laser light, which are then sheared. A novel configuration using the specular surface as a mirror to image speckles from a diffuser is presented, opening up the use of shearography to a new class of objects that could not have been examined with the traditional approach. This new technique readily identifies large scale bond failures in the panel, demonstrating the validity of this approach.

Lysak, Daniel B.↗