Search NASA⌕ Search

SEARCH · Search NASA

Results for “ammonia production”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Ammonia Formation by the Reduction of Nitrite/Nitrate by FeS: Ammonia Formation Under Acidic Conditions

FeS reduces nitrite to, ammonia at pHs lower than the corresponding reduction by aqueous Fe+2. The reduction follows a reasonable first order decay, in nitrite concentration, with a half life of about 150 min (room temperature, CO2, pH 6.25). The highest ammonia product yield measured was 53%. Under CO2, the product yield decreases from pH 5.0 to pH 6.9. The increasing concentration of bicarbonate at higher pH interferes with the reaction. Bicarbonate interference is shown by comparing runs under N2 and CO2. The reaction proceeds well in the presence of such species as chloride, sulfate, and phosphate though the yield drops significantly with phosphate. FeS also reduces nitrate and, unlike with Fe+2, the reduction shows more reproducibility. Again, the product yield decreases with increasing pH, from 7% at pH 4.7 to 0% at pH 6.9. It appears as if nitrate is much more sensitive to the presence of added species, perhaps not competing as well for binding sites on the FeS surface. This may be the cause of the lack of reproducibility of nitrate reduction by Fe+2 (which also can be sensitive to binding by certain species).

Summers, David P.↗
NASA NTRS1977

The distribution of ammonia and its photochemical products on Jupiter

Altitude profiles of ammonia and its photochemical products are generated in the light of measurements of the Jovian temperature structure, eddy transport coefficient, improved chemical scheme, and rate constants. Realistic limits are placed on the concentration of hydrazine which may participate in the recycling of ammonia on Jupiter. The maximum hydrazine-ice production rate is calculated to be about 1.3 mg/sq m per Jovian day. The distribution of nitrogen gas is presented with and without supersaturation of hydrazine. The nitrogen mixing ratio near the ammonia cloud top is estimated to be in the range between 10 to the -9th and 10 to the -11th power. An appreciable latitudinal variation in the ammonia concentration is expected.

Atreya, S. K.↗
DOE OSTI2020

Low temperature, ambient pressure electrochemical ammonia synthesis in alkaline media — Mechanistic studies and catalyst design. Final Report

Ammonia synthesis via the Haber-Bosch process is a pillar of modern agriculture, which converts the abundant but inert dinitrogen in the atmosphere to nitrogen-based fertilizers. Despite more than a century of optimization, the Haber-Bosch process remains energy intensive and reliant on fossil fuels and produces large amounts of CO 2 . Distributed and modular ammonia synthesis via the electrochemical nitrogen reduction reaction (ENRR) at or close to ambient conditions, powered by renewable electricity is an attractive alternative because it allows as needed production of ammonia, and in turn fertilizers. However, selective ENRR catalysts remain lacking. In this project, we systematically investigated two categories of catalytic materials, i.e., precious metals and transition metal nitrides, in the ENRR. Precious metals exhibit low activity and selectivity in the ENRR, which is in agreement with recent computational studies. Transition metal nitrides, especially VN, has been demonstrated as active and selective ENRR catalysts. We developed the first quantitative method to determine the amount of ammonia produced in the ENRR on N-containing containing catalysts in the membrane electrode assembly configuration. An initial ammonia production rate of 6.6 × 10 -10 mol s -1 mg -1 and a Faradaic efficiency of 6.0% at -0.1 V were reached on VN. After the initial deactivation, VN was shown to be stable in the ENRR for 116 hours with a steady state ammonia production rate of 1.1 × 10 -10 mol s -1 cm -2 . A vanadium oxynitride species was identified as the active phase in the ENRR via a combination of operando and ex situ characterization techniques. In addition, we established that the ENRR proceeded on transition metal nitrides via the Mars van Krevelen mechanism and determined the initial and steady state active site densities by developing a quantitative isotopic exchange method.

42 ENGINEERING↗
NASA NTRS1984

Production of ammonia-depleted surface layers on the Saturnian satellites by ion sputtering

On the basis of laboratory-derived data on the ion erosion of water and ammonia ices, it is suggested that the surfaces of the Saturnian satellites Enceladus, Tethys, Dione, and Rhea could have become enriched with water ice over a reasonable geological time period owing to the preferential erosion of the ammonia by magnetosphere ion bombardment. This mechanism serves as an alternative explanation to other processes invoked for the absence of ammonia spectral features in these satellites.

Lanzerotti, L. J.↗
DOE OSTI2021

Ammonia-fed reversible protonic ceramic fuel cells with Ru-based catalyst

Abstract The intermediate operating temperatures (~400–600 °C) of reversible protonic ceramic fuel cells (RePCFC) permit the potential use of ammonia as a carbon-neutral high energy density fuel and energy storage medium. Here we show fabrication of anode-supported RePCFC with an ultra-dense (~100%) and thin (4 μm) protonic ceramic electrolyte layer. When coupled to a novel Ru-(BaO) 2 (CaO)(Al 2 O 3 ) (Ru-B2CA) reversible ammonia catalyst, maximum fuel-cell power generation reaches 877 mW cm −2 at 650 °C under ammonia fuel. We report relatively stable operation at 600 °C for up to 1250 h under ammonia fuel. In fuel production mode, ammonia rates exceed 1.2 × 10 −8 NH 3 mol cm −2 s −1 at ambient pressure with H 2 from electrolysis only, and 2.1 × 10 −6 mol NH 3 cm −2 s −1 at 12.5 bar with H 2 from both electrolysis and simulated recycling gas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Electrically enhanced Haber-Bosch (EEHB) anhydrous ammonia synthesis

The present invention is directed to a method and system for enhancing the production of ammonia from gaseous hydrogen and nitrogen. Advantageously, the method and system does not emit carbon gases during production. The method and system enhances the production of ammonia compared to traditional Haber-Bosch reactions.

Beach, Joseph↗
DOE OSTI2022

Gamma Driven Catalysis of Ammonia

Experiments were conducted to investigate a passive production mechanism for the world’s most energy intensive commodity, ammonia. A novel method, gamma catalyzed ammonia production at ambient conditions, was investigated. Ammonia is currently produced through the highly energy intensive Haber-Fritz process, which requires an operation pressure of 400 atmosphere and 600 degrees Celsius. Due to the high demand and need for ammonia, the Haber-Bosch process consumes 25% all energy produced globally. Reported herein was an attempt to produce ammonia at ambient temperature (20 C) and ambient pressure (1 atm), through a novel process developed at PNNL, gamma driven catalysis of ammonia. Although the measurements of the ammonia production suggest wild success, reports in the literature by Gao et.al. suggest an experimental positive bias in the results. To rule out the potential positive bias, multiple additional production campaigns would be needed to with an alternate analysis technique such as ion chromatography, as suggested by Gao et.al. Unfortunately, due to this late determination of potential positive bias, the results of this study remain inconclusive to the feasibility of gamma driven catalysis of ammonia and more work is needed to describe the chemical evolution with time. The results are a first step and demonstrate that gamma-catalyst mediated reactions are possible. This represents a key opportunity to explore the fundamental chemistry of high band gap catalysts that can change the paradigm of radiation, transforming it from a waste to a valuable energy source.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
NASA NTRS1982

A photochemical study of the kinetics of the reactions of NH2 with phosphine, ethylene, and acetylene using flash photolysis-laser induced fluorescence

The photochemistry of the reactions of NH2 was investigated in an attempt to explain the existence of an abundance of ammonia in the Jovian atmosphere. The production of ammonia reservoirs from the coupling of ammonia with other atmospheric constituents was considered. The rate constants for the reactions of NH2 radicals with phosphine, acetylene, and ethylene were measured. Flash photolysis was used for the production of NH2 radicals and laser induced fluorescence was employed for radical detection. It was determined that the rates of the reactions were too slow to be significant as a source of ammonia reservoirs in the Jovian atmosphere.

Bosco, S. R.↗
NASA NTRS2009

Ammonia Release on ISS

Crew: Approximately 53% metabolic load Product of protein metabolism Limit production of ammonia by external regulation NOT possbile Payloads Potential source Scientific experiments Thorough safety review ensures sufficient levels of containment

Macatangay, Ariel↗
NASA NTRS2011

Fluorescence Excitation Models of Ammonia and Amidogen Radical (NH2) in Comets: Application to Comet C/2004 Q2 (Machholz)

Ammonia is a major reservoir of nitrogen atoms in cometary materials. However, detections of ammonia in comets are rare, with several achieved at radio wavelengths. A few more detections were obtained through near-infrared observations (around the 3 m wavelength region), but moderate relative velocity shifts are required to separate emission lines of cometary ammonia from telluric absorption lines in the 3 micron wavelength region. On the other hand, the amidogen radical (NH2 -- a photodissociation product of ammonia in the coma) also shows rovibrational emission lines in the 3 micron wavelength region. Thus, gas production rates for ammonia can be determined from the rovibrational emission lines of ammonia (directly) and amidogen radical (indirectly) simultaneously in the near-infrared. In this article, we present new fluorescence excitation models for cometary ammonia and amidogen radical in the near-infrared, and we apply these models to the near-infrared high-dispersion spectra of comet C/2004 Q2 (Machholz) to determine the mixing ratio of ammonia to water in the comet. Based on direct detection of NH3 lines, the mixing ratio of NH3/H2O is 0.46% +/- 0.03% in C/2004 Q2 (Machholz), in agreement with other results. The mixing ratio of ammonia determined from the NH2 observations (0.31% -- 0.79%) is consistent but has relatively larger error, owing to uncertainty in the photodissociation rates of ammonia. At the present level of accuracy, we confirm that NH3 could be the sole parent of NH2 in this comet.

Kawakita, Hideyo↗
DOE OSTI2024

Biohydrogen: prospects for industrial utilization and energy resiliency in rural communities

Biohydrogen (bioH 2 ) production in rural regions of the United States leveraged from existing biomass waste streams serves two extant needs: rural energy resiliency and decarbonization of heavy industry, including the production of ammonia and other H 2 -dependent nitrogenous products. We consider bioH 2 production using two different strategies: (1) dark fermentation (DF) and (2) anaerobic digestion followed by steam methane reforming of the biogas (AD-SMR). Production of bioH 2 from biomass waste streams is a potentially ‘greener’ pathway in comparison to natural gas-steam methane reforming (NG-SMR), especially as fugitive emissions from these wastes are avoided. It also provides a decarbonizing potential not found in water-splitting technologies. Based on literature on DF and AD of crop residues, woody biomass residues from forestry wastes, and wastewaters containing fats, oils, and grease (FOG), we outline scenarios for bioH 2 production and displacement of fossil fuel derived methane. Finally, we compare the costs and carbon intensity (CI) of bioH 2 production with those of other H 2 production pathways.

08 HYDROGEN↗
DOE OSTI2026

Findings from Large Bench-Scale Testing of Denitration Electrolyzers for the EDCGe Project

This report highlights the key findings and outcomes relevant to the processability of waste supernatant at Hanford using a denitration electrolyzer. The Electrosynthesis Company issued a Phase 1 report to the Savannah River National Laboratory (SRNL), summarizing the evaluation of large bench-scale denitration electrolyzers to support the electrochemical denitration and caustic generation (EDCGe) project. The Electrosynthesis Company’s report (attached as Appendix A) provides insights into the initial steps required to implement an electrolyzer system at Hanford. Phase 1 experiments focused on validating the denitration electrolyzer’s performance, operating parameters, and reaction products. The robustness of the electrochemical denitration process was demonstrated by two electrolyzer flow cell systems (a 100 cm 2 ElectroCell MP and a 150 cm 2 NESI NS01 cell), both of which achieved significant nitrate and nitrite removal (>50%) with a current efficiency of ~95% for both systems. Higher current densities (500 mA cm –2 ) improved nitrate and nitrite removal rates compared to lower current densities (333 mA cm –2 ), while maintaining a current efficiency of ~94%. The NS01 cell achieved a nitrate species removal rate of ~0.41 mol h –1 at 5 kA m –2 (equiv. to 500 mA cm –2 ). The primary reaction product was ammonia (NH 3 ), constituting 78.3–91.6% of the products (excluding OH – formation). NH 3 was predominantly retained in the catholyte liquid phase rather than being off-gassed. Additionally, the NS01 cell reported an NH 3 generation rate of ~0.36 mol h –1 at 5 kA m –2 . Other gas formation included ~7% N 2 , ~7% H 2 , and trace amounts of N 2 O. The estimated power requirement (extrapolated from the 0.015 m 2 cell data) for a full-scale denitration electrolyzer is approximated to be ~1.6 MW (DC-only) to treat 50% of nitrate and nitrite in a waste stream and generates ~2.1 kmol h –1 of NH 3 with an initial concentration of 4 M NO 3 – /NO 2 – at 300 gal h –1 . Simulated waste containing aluminate, carbonate, oxalate, and halogens exhibited no adverse effects on denitration performance. A preliminary experiment comparing alkaline anolyte (5 M NaOH) with a nickel based anode to acidic media (2 M H 2 SO 4 ) with a DSA-O 2 anode showed a lower operating voltage and generated less H 2 than the acid media. Maintaining a stable 5 M OH – concentration in the anolyte through periodic additions of caustic did not significantly impact denitration performance. This operational mode will be required for long-term experiments. All the experiments demonstrated that electrochemical denitration is a promising approach for treating nitrate and nitrite in simulated waste streams, achieving significant conversion and robustness across varying experimental conditions and electrochemical cell configurations. Lastly, the ability to generate a nearly pure NH 3 stream may prove advantageous for processing at other locations within the Hanford site.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Renewable ammonia for sustainable energy and agriculture: vision and systems engineering opportunities

Synthetic ammonia is essential for agriculture, but its production at present is unsustainable. Ammonia synthesized with hydrogen from renewable-powered electrolysis and nitrogen separated from air has the potential to alleviate these sustainability concerns while also having promise as a low-cost storage medium for intermittent renewable energy. This paper reviews recent research and development on the topic of renewable ammonia production and utilization as fertilizer and as energy storage. We describe our vision for synergistically combining these renewable ammonia applications to improve sustainability. Furthermore, we outline opportunities for systems engineering to play a crucial role in advancing the adoption of renewable ammonia in a manner which is sustainable, economically competitive, and reliable.

10 SYNTHETIC FUELS↗
DOE OSTI2021

Achieving industrial ammonia synthesis rates at near-ambient conditions through modified scaling relations on a confined dual site

The production of ammonia through the Haber–Bosch process is regarded as one of the most important inventions of the 20th century. Despite significant efforts in optimizing the process, it still consumes 1 to 2% of the worldwide annual energy for the high working temperatures and pressures. The design of a catalyst with a high activity at milder conditions represents another challenge for this reaction. Herein, we combine density functional theory and microkinetic modeling to illustrate a strategy to facilitate low-temperature and -pressure ammonia synthesis through modified energy-scaling relationships using a confined dual site. Our results suggest that an ammonia synthesis rate two to three orders of magnitude higher than the commercial Ru catalyst can be achieved under the same reaction conditions with the introduction of confinement. Such strategies will open pathways for the development of catalysts for the Haber–Bosch process that can operate at milder conditions and present more economically viable alternatives to current industrial solutions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Outlook on Industrial Requirements for Incorporating Nuclear Energy into Industrial Processes

There is an increasing interest globally and in the U.S. in decarbonizing heavy industrial processes which have large demands for heat and power. Currently these industries primarily use fossil fuels to meet these demands and they include: oil & gas, petroleum refining, chemicals and derivative products manufacturing, iron & steel production, polymers, ammonia and fertilizers, etc. The U.S. DOE Integrated Energy Systems (IES) program seeks to identify and analyze opportunities for integrating and substituting nuclear energy to fulfil these large heat and power demands in a cost competitive and sustainable manner while reducing carbon emissions of the processes by using clean nuclear power. Presently various representatives from a subset of these industrial companies have expressed interest in evaluating the options of integrating future advanced nuclear small modular reactors with their industries. This study is a scoping study to provide an outlook of industrial energy demands and the potential nuclear energy substitution potential. Future work will analyze in a more detailed manner the potential designs for coupling advanced nuclear reactors with various industries. The industrial processes of oil refining, methanol production, pulp and paper, ammonia and chlorine-alkali are described focusing on how heat and power is used within the facilities in the context of identifying nuclear substitution opportunities. The aim is to provide reliable, competitive, and sustainable energy that is clean while reducing carbon emissions and other environmental impacts such as water withdrawals, consumption, and contamination.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗