Search NASA⌕ Search

SEARCH · Search NASA

Results for “atomic forces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Viscoelastic-Mapping of Cellulose Nanofibrils Using Low-Total-Force Contact Resonance Force Microscopy (LTF-CRFM)

Low-total-force contact resonance force microscopy (LTF-CRFM), an atomic force microscopy method, is introduced as a non-destructive means to quantify the local viscoelastic loss tangent (tan..delta..) of supported cellulose nanofibrils (CNFs). The method limits static and dynamic forces during measurement to minimize substrate and geometry effects and to reduce the potential for stress-induced CNF damage. LTF-CRFM uses Brownian motion to achieve the thermally-limited lowest dynamic force, while approaching adhesive pull-off to achieve the low static force. LTF-CRFM measurements were shown to generate analyzable data without evidence of nonlinear artifacts and without damage to the CNF over static forces ranging from 11.6 to 84.6 nN. The measured tan..delta.. of CNFs was 0.015 +/- 0.0094, which is the first reported tan..delta.. measurement of an isolated CNF. Finally, LTF-CRFM successfully mapped tan..delta.. along the length of CNFs to determine that kink defects along the CNF do not impart a local viscoelastic property change at the spatial resolution of the measurement.

BIOMASS FUELS↗
DOE OSTI2020

Thickness and strain dependence of piezoelectric coefficient in BaTiO 3 thin films

We explore the thickness dependence of the converse piezoelectric coefficient (d 33 ) in epitaxial thin films of BaTiO 3 (BTO) grown on (001) SrTiO 3 substrates. Piezoresponse force microscope was performed using an atomic force microscope equipped with an interferometric displacement sensor allowing direct quantification of electromechanical coupling coefficients in BTO free from unwanted background contributions. We find that 80-nm-thick films exhibit a d 33 of ~20.5pm/V, but as the thickness is reduced, the d 33 reduces to less than 2 pm/V for a 10 nm film. To explain the atomistic origin of the effect, we performed molecular dynamics simulations with a recently developed ab initio-derived reactive force field, constructed using the ReaxFF framework. Simulations predict that under applied electric fields thin films of BaTiO 3 show an increasing thickness, with compressive strain, of the region screening the depolarization-field. This study confirms quantitatively the drop in piezoelectric performance in BTO ultrathin films and again highlights the importance of the screening mechanisms when films approach the ultrathin limits in dictating the functional behaviors.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Direct Imaging of the Structural and Morphological Evolution of Epitaxial LiCoO 2 Films during Charge and Overcharge

The capacity decay of layered cathodes in high-voltage applications underscores the need to utilize accurate and precise techniques to understand the underlying mechanisms. Here, we use well-defined epitaxial LiCoO 2 (LCO) films on SrRuO 3 /SrTiO 3 (SRO/STO) with controlled orientations and defect structures along with in situ electrochemical atomic force microscopy to probe the structural and morphological evolutions during the charge and overcharge processes. We quantitatively show the morphological changes in both the reversible delithiation regime and the irreversible over-delithiation regime and correlate the overall electrochemical behaviors to atomic scale defect evolutions in the films. Further, we also observe a significantly lower charging capacity for LCO/SRO/STO(111) compared to that of LCO/SRO/STO(001) films of the same thickness, which is ascribed to different types of atomic scale defects formed during the film growth process. Our high- resolution scanning transmission electron microscopy (STEM) and electron energy loss spectroscopy (EELS) studies reveal that the antiphase boundaries in LCO/SRO/STO(111) act as viable channels for Li migration but are more susceptible to irreversible phase transitions, which then block subsequent Li diffusion. The failure mechanisms developed here may provide insight into the design of future cathode materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Pulsed laser deposition nickel oxide on crystalline silicon as hole selective contacts

In this work, the authors report the use of pulsed laser deposition to fabricate nickel oxide layers on silicon and assess the applicability of this structure as a hole selective contact. Films were deposited at temperatures of 300, 500, 700, and 900 °C. Results from reflective high energy electron diffraction patterns indicate increasing crystallinity with temperature up to 500 °C. However, layers deposited at 900 °C are amorphous. Nevertheless, results from atomic force microscopy, contact resistance measurements, and photoluminescence lifetime imaging indicate that films deposited at 900 °C have the best film smoothness, lowest specific contact resistivity, and highest lifetimes, and therefore, they are best suited for hole selective contact applications. Kelvin probe force microscopy and x-ray photoelectron spectroscopy were also carried out to study the effects of deposition temperature.

42 ENGINEERING↗
DOE OSTI2021

Fracture and fatigue of thin crystalline SrTiO 3 membranes

The increasing availability of a variety of two-dimensional materials has generated enormous growth in the field of nanoengineering and nanomechanics. Recent developments in thin film synthesis have enabled the fabrication of freestanding functional oxide membranes that can be readily incorporated in nanomechanical devices. While many oxides are extremely brittle in bulk, recent studies have shown that, in thin membrane form, they can be much more robust to fracture as compared to their bulk counterparts. Here, we investigate the ultimate tensile strength of SrTiO 3 membranes by probing freestanding SrTiO 3 drumheads using an atomic force microscope. We demonstrate that SrTiO 3 membranes can withstand an elastic deformation with an average strain of ~6% in the sub-20 nm thickness regime, which is more than an order of magnitude beyond the bulk limit. Further, we also show that these membranes are highly resilient upon a high cycle fatigue test, surviving up to a billion cycles of force modulation at 85% of their fracture strain, demonstrating their high potential for use in nanomechanical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Hybrid chemical characterization of latent images in EUV resist with 12 nm half-pitch features

With the advancement of high numerical aperture extreme ultraviolet (EUV) lithography, the new platform will enable chipmakers to achieve critical dimensions of 8 nm. However, resist materials face significant challenges in delivering increased sensitivity while managing rising stochastic variations. We aim to develop comprehensive techniques to characterize the chemical profile of latent images, stored in EUV resists after exposure and postexposure baking, which is essential for understanding the origin of stochastic effects. Infrared photo-induced force microscopy (IR PiFM) is a bimodal atomic force microscopy technique combined with an infrared light source, allowing for simultaneous sub-5 nm topographic and chemical characterization within a localized environment. Critical-dimension resonant soft X-ray scatterometry (CD-RSoXS) provides statistical data that reveal structural and chemical information for comparative analysis. For the first time, IR PiFM has been used to chemically map the latent images of EUV resists (after exposure and postexposure baking) at a record high resolution of 12 nm half-pitch, enabling nondestructive analysis of patterns prior to development. Furthermore, CD-RSoXS offers direct experimental observation and comparison of exposed, postexposure baked, and developed patterns, which align with the IR PiFM results. We demonstrate that the IR PiFM technique offers valuable insights into both high spatial resolution and local chemical information simultaneously. In addition, CD-RSoXS provides statistical results that support our main findings. This hybrid metrology approach leverages a multifaceted dataset by combining the most reliable information from each source, which is essential for a comprehensive understanding of the stochastic effects in EUV lithography processes.

O’Reilly, Padraic↗
DOE OSTI2022

Array of Graphene Variable Capacitors on 100 mm Silicon Wafers for Vibration-Based Applications

Highly flexible, electrically conductive freestanding graphene membranes hold great promise for vibration-based applications. This study focuses on their integration into mainstream semiconductor manufacturing methods. We designed a two-mask lithography process that creates an array of freestanding graphene-based variable capacitors on 100 mm silicon wafers. The first mask forms long trenches terminated by square wells featuring cone-shaped tips at their centers. The second mask fabricates metal traces from each tip to its contact pad along the trench and a second contact pad opposite the square well. A graphene membrane is then suspended over the square well to form a variable capacitor. The same capacitor structures were also built on 5 mm by 5 mm bare dies containing an integrated circuit underneath. We used atomic force microscopy, optical microscopy, and capacitance measurements in time to characterize the samples.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Unusual flat and extended morphology of intercalated Cu under MoS 2

We report a general method was developed to intercalate metals under layered materials through a controlled density of sputtered defects. The method has already been applied to study a range of metals intercalated under graphite, and different types of morphologies were realized. In the current work, we extend the method to the study of intercalation under MoS 2 , noting that work on this system is rather limited. We use Cu as the prototype metal for comparison with Cu intercalation under graphite. Although the growth conditions needed for intercalation under graphite and MoS 2 are similar, the type of intercalated phases is very different. Each Cu island that nucleates on top of MoS 2 during Cu deposition provides material that is transferred below MoS 2 through sputtered defects under the island base; this transfer results in a uniform intercalated Cu “carpet” morphology that extends over the mesoscale. On the contrary, Cu intercalation under graphite results in well separated, compact islands formed by monomer detachment from small Cu islands on top and transfer below through defects far from the islands. The structural techniques (scanning electron microscopy and atomic force microscopy) and spectroscopic techniques (x-ray photoelectron spectroscopy and energy-dispersive spectroscopy) are used for the characterization of the intercalated Cu layer.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Reliability Implications of Solder in Multiwire Modules under Dynamic Mechanical Loading

Two generations of multiwire modules were studied under dynamic mechanical loading (DML) with in-situ differential conductance (dG) and electroluminescence (EL) imaging. Energy-dispersive x-ray spectroscopy (EDS) was used to identity the solder alloys. The earlier generation module was found to use an In-based solder alloy, and the current generation a Bi-based alloy. The earlier generation module degraded significantly under DML with increasing resistance, while the current generation module did not demonstrate degradation under DML. Atomic force microscopy scratch testing was used to probe the wear resistance of each solder alloy. These results indicate that current multiwire designs may have higher mechanical durability than earlier generations.

atomic force microscopy↗
DOE OSTI2023

Spin-dependent charge transmission through chiral 2T3N self-assembled monolayer on Au

In this study, a gold surface is functionalized by chemisorption of the enantiopure N,N'-bis-[2,2';5',2"]tert-thiophene-5-yl methylcyclohexane-1,2-diamine (2T3N), a chiral oligothiophene derivative, via overnight incubation in a 2T3N ethanol solution. The Au|2T3N interface is characterized by x-ray photoelectron circular dichroism and comparing x-ray photoemission spectroscopy and electro-desorption results. Charge transmission at the Au|2T3N| solution interface is characterized by recording the cyclic voltammetry of the Fe(III)/Fe(II) reversible redox couple, finding a charge transfer rate constant, k°, variation from 1 × 10 -1 to 3.3 × 10 -2 cm s -1 , when comparing the bare Au and the Au|2T3N interfaces, respectively. The “anomalous” high value of k° found for the chiral Au|2T3N interface can be rationalized on the basis of the chiral-induced spin selectivity effect, as further proved by magnetic–conductive atomic force microscopy measurements at room temperature. A spin polarization of about 30% is found.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Carbonation dynamics of hydrated alite revealed by electron microscopy

CO 2 sequestration in concrete is crucial to relieve the environmental burden, while the carbonation mechanisms remain unclear. Here, we explored the carbonation dynamics of alite hydrates through electron microscopy. We discovered that calcite is the main phase of carbonate crystals throughout the entire carbonation period in the alite system. Further, the shape evolution of calcite crystals was captured: spindle carbonates initially formed on C-S-H substrate and then transformed into rhombohedrons; Intermediate states such as polyhedral particles and layered rhomboids were also observed. Based on our quantitative calculations, the growth rate of calcite particles was determined approximately 0.2 μm/day, which may be affected by the relative concentration between calcium ions and CO 2 source. A direct relation between the microstructure and mechanical properties of calcite was uncovered using atomic force microscopy. Furthermore, we found that the morphology development of calcite crystals during carbonation may be explained by the surface energy variation of different facets. This work suggests a unique approach to track carbonation kinetics and provides new opportunities to unveil underlying carbonation mechanisms at the nanoscale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Cesium intercalation of graphene: A 2D protective layer on alkali antimonide photocathode

Alkali antimonide photocathodes have wide applications in free-electron lasers and electron cooling. The short lifetime of alkali antimonide photocathodes necessitates frequent replacement of the photocathodes during a beam operation. Furthermore, exposure to mediocre vacuum causes loss of photocathode quantum efficiency due to the chemical reaction with residual gas molecules. Theoretical analyses have shown that covering an alkali antimonide photocathode with a monolayer graphene or hexagonal boron nitride protects it in a coarse vacuum environment due to the inhibition of chemical reactions with residual gas molecules. Alkali antimonide photocathodes require an ultra-high vacuum environment, and depositing a monolayer 2D material on it poses a serious challenge. In the present work, we have incorporated a novel method known as intercalation, in which alkali atoms pass through the defects of a graphene thin film to create a photocathode material underneath. Initially, Sb was deposited on a Si substrate, and a monolayer graphene was transferred on top of the Sb film. Heat cleaning around 550–600 °C effectively removed the Sb oxides, leaving metallic Sb underneath the graphene layer. Depositing Cs on top of a monolayer graphene enabled the intercalation process. Atomic force microscopy, Raman spectroscopy, x-ray photoelectron spectroscopy, low energy electron microscopy, and x-ray diffraction measurements were performed to evaluate photocathode formation underneath the monolayer graphene. Our analysis shows that Cs penetrated the graphene and reacted with Sb and formed Cs 3 Sb.

2D materials↗
DOE OSTI2021

Reliability Implications of Solder in Multiwire Modules under Dynamic Mechanical Loading: Preprint

Two generations of multiwire modules were studied under dynamic mechanical loading (DML). The earlier generation module was found to use an In-based solder alloy, and the current generation a Bi-based alloy. The earlier generation module degraded significantly under DML with increasing resistance, while the state-of-the-art module did not demonstrate degradation under DML. The degradation in the earlier module was attributed to damage at the solder-gridline interfaces. Atomic force microscopy scratch testing estimated the wear resistance of each solder alloy to assess susceptibility to degradation. Bi-based alloys appear to be more wear resistant than In-based alloys, consistent with the DML results. These results indicate that current multiwire designs may have higher mechanical durability than earlier generations.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2024

Origin of deactivation of aqueous Na–CO 2 battery and mitigation for long-duration energy storage

Here, the development of long-duration energy storage technology is crucial to facilitate the efficient utilization of renewable energy sources while mitigating carbon dioxide production. In this study, we investigate the deactivation and reactivation mechanisms of the aqueous Na–CO 2 battery during extended cycling. We have designed the cathode to include non-precious intermetallic catalysts. As the cell undergoes repeated cycles, the voltage polarization during discharge progressively rises, eventually leading to the cell's deactivation and formation of decomposition products clogging the electrode surface. Results obtained from comprehensive characterization techniques, including conductive atomic force microscopy (cAFM), Raman spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction, and inductively coupled plasma-mass spectrometry provide insight into the decomposition products. We also showcase an electrochemical approach for regeneration of these aqueous cells. Our findings, along with the insights we have gained, provide a path toward creating long-duration systems with self-healing properties.

25 ENERGY STORAGE↗
DOE OSTI2023

Exploring internal structures and properties of terpolymer fibers via real-space characterizations

While significant research has investigated the processing and properties of high-performance terpolymer fibers, much remains to be understood about the internal nano- and microstructures of these fibers, and how these morphologies relate to fiber properties. Here we use a focused ion beam notch technique and multifrequency atomic force microscope mapping to characterize the internal structure and local mechanical properties within Technora ® fibers. We find a highly fibrillated structure that appears to connect with both the fiber’s molecular chemistry and full-fiber mechanical properties. In addition, through detailed comparisons with Kevlar ® K29 fibers, we find remarkable differences between the internal structures of the two fibers, and posit connections between our measurements and multifunctional performance studies from the literature.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Nanodiamonds with SiV colour centres for quantum technologies

Properties of silicon-vacancy (SiV) colour centres in ultra-nanosize diamonds are studied. Nanodiamonds are obtained at a high temperature and pressure, which induced transformations in mixtures of organic and hetero-organic compounds without metal-catalysts. The size distribution of grown nanodiamonds is determined by the methods of transmission electron microscopy and atomic-force microscopy, as well as by using the model of phonon spatial localisation. In addition, Raman spectra of various nanodiamonds and luminescence properties of SiV-centres are investigated. (laser applications and other topics in quantum electronics)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Grafted polythiophene pendent polymer brushes and their electronanopatterning

Here electrochemical nanolithography using grafted polymer brushes with terthiophene (3T) pendent was investigated. The film was fabricated by surface electropolymerization of a reversible addition-fragmentation chain-transfer agent macroinitiator containing a 3T pendant molecule and the subsequent polymer brush growth from a 3T functionalized methacrylate monomer (3T-Methacrylate). Electrochemical nanolithography and patterning were done using conducting atomic force microscopy (C-AFM) enabling precise nanopattern fabrication. In contrast to direct nanowriting, dip pen nanolithography, and nanolithographic additive manufacturing, the electrochemical nanolithography can be readily facilitated by applying a bias voltage between a conductive AFM tip and the grafted polymer brush film at ambient conditions and without ink transfer. The height and electrical resistance of the nanopatterns were dependent on the writing parameters (i.e. applied bias voltage and scan rate).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Local electrical degradations of solid-state electrolyte by nm-scale operando imaging of ionic and electronic transports

We report on degradation mechanisms of solid-state electrolyte (SSE) based on insights from nm-scale ionic conduction and electronic leakage for solid-state batteries. The significantly different local degradations revealed by nm-scale ionic and electronic transport imaging demonstrate the need for this nm-scale investigation. State-of-the-art lithium-ion conductive glass ceramic (Li 2 O–Al 2 O 3 –SiO 2 –P 2 O5–TiO2-GeO2) SSE shows at least two types of degradations spatially separated within the SSE, namely: (1) ionic conduction blocking and slight electronic leaking and (2) highly electronic shunting. Degradation was significantly suppressed by application of a Li-containing polyacrylonitrile thin coating on both sides of the ceramic SSE. With this coating, the ionic conduction was not reduced by the extensive cycling; instead, it improved slightly, although accompanied by a slight increase in electronic leaking. Our nm-scale transport imaging was achieved using an atomic force microscopy (AFM)-based half-cell setup and a logarithmic-scale amplifier with current sensitivity down to the fA (10-15 A) range. This half-cell setup consisting of an AFM-probe/SSE/Li structure can distinguish the ionic from the electronic current by flipping the bias-voltage polarity. This nm-scale operando imaging opens up novel characterization of ionic and electronic transport in the field of solid-state batteries.

42 ENGINEERING↗