SEARCH · Search NASA

Results for “boundary layer analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Numerical design of the contoured wind-tunnel liner for the NASA swept-wing LFC test

A contoured, nonporous, wind-tunnel liner has been designed in order to simulate a free-flight infinite yawed-wing, transonic-flow condition about a large-chord, supercritical-section, laminar-flow-control (LFC), swept-wing test panel. The numerical procedure developed for this aerodynamic liner design is based upon the simple idea of streamlining and incorporates several existing transonic and boundary-layer analysis codes. A summary of the entire procedure is presented to indicate: what was done and why, the sequence of steps, and the overall data flow. The liner is being installed in the NASA Langley 8-Foot Transonic Pressure Tunnel (TPT). Test results indicating the aerodynamic performance of the liner are not yet available; thus, the liner design results given here are examples of the calculated requirements and the hardware implementation.

Newman, P. A.↗

NASA NTRS1983

Aerodynamic optimization, comparison, and trim design of canard and conventional high performance general aviation configurations

A design study has been conducted to optimize trim cruise flight of high performance general aviation canard aircraft which achieve minimum drag. In order to investigate the advantages and disadvantages of canard configured aircraft, corresponding conventional tail-aft 'baseline' aircraft were designed and used for comparison. Two-dimensional predictions were obtained by coupling inviscid results from a vortex panel multi-element program to a momentum integral boundary layer analysis. Using the results of the two-dimensional vortex panel analysis, a vortex lattice method was employed to predict the finite wing results. The analysis utilized a turbulent airfoil and a natural laminar airfoil which are two NASA state-of-the-art airfoil sections. The canard aircraft designs give quantitative results of wing and canard loadings, wing-to-canard moment arm ratios, and aspect ratio effects for trim cruise flight for a wide range of wing-to-canard area ratios. Both canard and baseline aircraft achieved a 25 to 30 percent improvement in performance over typical current technology aircraft, but high canard loading necessary for trim resulted in slightly poorer performance of the canard aircraft as compared to the baseline designs.

Keith, M. W.↗

NASA NTRS1984

Aerodynamic characteristics of the 40- by 80/80- by 120-foot wind tunnel at NASA Ames Research Center

The design and testing of vane sets and air-exchange inlet for the 40 x 80/80 x 120-ft wind tunnel at NASA Ames are reported. Boundary-layer analysis and 2D and 3D inviscid panel codes are employed in computer models of the system, and a 1/10-scale 2D facility and a 1/50-scale 3D model of the entire wind tunnel are used in experimental testing of the vane sets. The results are presented in graphs, photographs, drawings, and diagrams are discussed. Generally good agreement is found between the predicted and measured performance.

Corsiglia, V. R.↗

NASA NTRS1984

Aerodynamic design of the contoured wind-tunnel liner for the NASA supercritical, laminar-flow-control, swept-wing experiment

An overview is presented of the entire procedure developed for the aerodynamic design of the contoured wind tunnel liner for the NASA supercritical, laminar flow control (LFC), swept wing experiment. This numerical design procedure is based upon the simple idea of streamlining and incorporates several transonic and boundary layer analysis codes. The liner, presently installed in the Langley 8 Foot Transonic Pressure Tunnel, is about 54 ft long and extends from within the existing contraction cone, through the test section, and into the diffuser. LFC model testing has begun and preliminary results indicate that the liner is performing as intended. The liner design results presented in this paper, however, are examples of the calculated requirements and the hardware implementation of them.

Newman, P. A.↗

NASA NTRS1984

Aerodynamic characteristics of the 40- by 80-/80- by 120-ft wind tunnel at NASA-Ames Research Center

The design and testing of vane sets and air-exchange inlet for the 40 x 80/80 x 120-ft wind tunnel at NASA Ames are reported. Boundary-layer analysis and 2D and 3D inviscid panel codes are employed in computer models of the system, and a 1/10-scale 2D facility and a 1/50-scale 3D model of the entire wind tunnel are used in experimental testing of the vane sets. The results are presented in graphs, photographs, drawings, and diagrams and discussed. Generally good agreement is found between the predicted and measured performance.

Corsiglia, V. R.↗

NASA NTRS1986

Investigation of chord ratio, stagger, decalage angle, and flap angle for dual wing configurations

Aerodynamical closely coupled dual wing configurations of unequal chords are investigated for medium speed general aviation applications. Vortex panel and momentum boundary layer analysis are utilized for the two-dimensional predictions. A multi-surface vortex lattice method is used for the three-dimensional predictions. In the process of searching for the highest lift to drag ratio upper airfoil to lower airfoil chord ratios, both greater than and less than one, are investigated in terms of stagger, decalage angle, and gap. With the optimum chord ratio, at the optimum stagger and gap, proper spanwise decalage distribution is shown to yield the lowest two dimensional drag results. Various wing taper ratios and wing twists are investigated to increase wing efficiency. Comparisons are made between optimized dual and optimized single wing configurations both with the same fuselage, stabilator surfaces, engines, payload, and fuel. The dual wing configuration is shown to have significantly less drag and hence longer range than the conventional single wing configuration.

Selberg, B. P.↗

NASA NTRS1985

Observations of the right-hand resonant ion beam instability in the distant plasma sheet boundary layer

Examples of the onset of a resonant ion beam instability are illustrated on the basis of ISEE 3 observations of 66 large amplitude wave events at the plasma sheet boundary layer. Analysis of the observational data showed that the observed wave and ion beam parameters were, in general, in agreement with linear theoretical predictions of resonant ion beam instability. The distribution of ion energies at the onset of the instability is given in a table.

Tsurutani, B. T.↗

NASA NTRS1987

Optimal heading change with minimum energy loss for a hypersonic gliding vehicle

A three state model is presented for analyzing the problem of optimal changes in heading with minimum energy loss for a hypersonic gliding vehicle. A further model order reduction to a single state model is examined using singular perturbation theory. The optimal solution for the reduced problem defines an optimal altitude profile dependent on the current energy of the vehicle, and the corresponding optimal lift and bank angle. A separate boundary layer analysis, based on an expansion of the necessary conditions about the reduced solution, is used to account for altitude and flight path angle dynamics and to derive a guidance law in feedback form. The guidance law is evaluated for a hypothetical vehicle.

Calise, Anthony J.↗

NASA NTRS1988

Modeling of liquid jets injected transversely into a supersonic crossflow

Analytical/numerical modeling of the behavior of a single nonreacting liquid jet in compressible (high subsonic and supersonic) crossflows is described here. Inviscid, compressible flow about the elliptical cross-section of the jet is solved numerically, using a procedure modeled after that of Godunov. External boundary layer analysis along the surface of the elliptical cross-section allows determination of an effective drag associated with the jet, which balances centripetal forces resulting from jet deflection. Mass and momentum balances performed along the jet, with and without the inclusion of mass loss due to droplet shedding, are then incorporated so that liquid jet trajectories and bow shock penetration may be calculated. Comparisons of the predictions are made with experimental results.

Heister, S. D.↗

NASA NTRS1988

Trajectory optimization and guidance law development for national aerospace plane applications

The problem of onboard trajectory optimization for an airbreathing, single-stage-to-orbit vehicle is examined. A simple model representative of the aerospace plane concept, including a dual-mode propulsion system composed of scramjet and rocket engines, is presented. Consideration is restricted to hypersonic flight within the atmosphere. An energy state approximation is used in a four-state model for flight of a point mass in a vertical plane. Trajectory constraints, including those of dynamic pressure and aerodynamic heating, are initially ignored. Singular perturbation methods are applied in solving the optimal control problem of minimum fuel climb. The resulting reduced solution for the energy state dynamics provides an optimal altitude profile dependent on energy level and control for rocket thrust. A boundary-layer analysis produces an approximate lift control solution in feedback form and accounts for altitude and flight path angle dynamics. The reduced solution optimal climb path is presented for the unconstrained case and the case for which a maximum dynamic pressure constraint is enforced.

Calise, A. J.↗

NASA NTRS1987

Measurement of airfoil heat transfer coefficients on a turbine stage

A combined experimental and analytical program was conducted to examine the impact of a number of variables on the midspan heat transfer coefficients of the three airfoil rows in a one and one-half stage large scale turbine model. Variables included stator/rotor axial spacing, Reynolds number, turbine inlet turbulence, flow coefficient, relevant stator 1/stator 2 circumferential position, and rotation. Heat transfer data were acquired on the suction and pressure surfaces of the three airfoils. High density data were also acquired in the leading edge stagnation regions. Extensive documentation of the steady and unsteady aerodynamics was acquired. Finally, heat transfer data were compared with both a steady and an unsteady boundary layer analysis.

Dring, Robert P.↗

NASA NTRS1990

Collisionless tearing instability in magnetotail plasmas

The problem of the linear stability of collisionless tearing modes in the earth's magnetotail is revisited. It is found that the collisionless tearing mode is linearly unstable with wavelengths of the order of 10 R(E). It is shown that an important feature neglected in earlier theories is a nonzero equilibrium B(y)-field. The physics of the instability is elucidated in the context of a simple slab model and a sheared parabolic model which is representative of the magnetotail in which all three components of the magnetic field are nonzero. The dispersion equation for the instability is obtained by a boundary-layer analysis. The implications of the theory for recent observations on current disruption and diversion during substorms is discussed.

Wang, Xiaogang↗

NASA NTRS1991

Generalized multi-point inverse airfoil design

In a rather general sense, inverse airfoil design can be taken to mean the problem of specifying a desired set of airfoil characteristics, such as the airfoil maximum thickness ratio, pitching moment, part of the velocity distribution or boundary-layer development, etc., then from this information determine the corresponding airfoil shape. This paper presents a method which approaches the design problem from this perspective. In particular, the airfoil is divided into segments along which, together with the design conditions, either the velocity distribution or boundary-layer development may be prescribed. In addition to these local desired distributions, single parameters like the airfoil thickness can be specified. The problem of finding the airfoil shape is determined by coupling an incompressible, inviscid, inverse airfoil design method with a direct integral boundary-layer analysis method and solving the resulting nonlinear equations via a multidimensional Newton iteration technique. The approach is fast and easily allows for interactive design. It is also flexible and could be adapted to solving compressible, inverse airfoil design problems.

Selig, Michael S.↗

NASA NTRS1992

Magnetic flipping - Reconnection in three dimensions without null points

In three dimensions, magnetic reconnection may take place in a sheared magnetic field at any singular field line, where the nearby field has X-type topology in planes perpendicular to the field line and where an electric field is present parallel to the field line. In the ideal region around the singular line there will, in general, be singularities in the plasma flow and electric field, both at the singular line and at 'magnetic flipping layers', which are remnants of local magnetic separatrices. In the absence of a three-dimensional magnetic neutral point or null point, reconnection of field lines can still occur by a process of magnetic flipping, in which the plasma crosses the flipping layers but the field lines rapidly flip along them by magnetic diffusion. Depending on the boundary conditions, there may be two or four flipping layers which converge on the singular line. A boundary layer analysis of a flipping layer is given, in which the magnetic field parallel to the layer decreases as one crosses it while the plasma pressure (or magnetic pressure associated with the field along the singular line) increases. The width of the flipping layer decreases with distance from the singular line.

Priest, E. R.↗

NASA NTRS1992

Nature of buoyancy-driven flows in a reduced-gravity environment

The role of buoyancy-driven convection in reduced-gravity environments has been emphasized. It is shown that for some materials-processing experiments the values of the fundamental dimensionless parameters such as Gr or Ra are shifted from the very large (ground-based values) to moderately large (space-based values). As a consequence, in cases where approximate analytical solutions are desired, the accuracy of the usual asymptotic (boundary-layer) analysis in which infinitely large parametric ranges are assumed is reduced. Approximate analytical techniques for refinement of the asymptotic solutions are identified that will extend the accuracy to the moderately large parametric ranges associated with space-based processing.

Kassemi, Siavash A.↗

NASA NTRS1992

Computed unsteady flows of airfoils at high incidence

The flow over an airfoil at an angle of attack above the static stall angle would ordinarily be massively separated. Under dynamic conditions, the onset of stall can be delayed to an angle, depending on the type of unsteadiness, much higher than that for static stall. The stall onset mechanisms under dynamic conditions are unclear. Due to extreme difficulties involved, experimental investigations, so far, have provided insufficient information about the flow field for the identification of the onset mechanisms. A course of classical boundary layer analysis augmented with numerical experiments and measured data is chosen here instead, with the hope that the identification of onset mechanisms can be more systematic and quantitative.

Fung, K.-Y.↗

NASA NTRS1999

Potential Flow Theory and Operation Guide for the Panel Code PMARC

The theoretical basis for PMARC, a low-order panel code for modeling complex three-dimensional bodies, in potential flow, is outlined. PMARC can be run on a wide variety of computer platforms, including desktop machines, workstations, and supercomputers. Execution times for PMARC vary tremendously depending on the computer resources used, but typically range from several minutes for simple or moderately complex cases to several hours for very large complex cases. Several of the advanced features currently included in the code, such as internal flow modeling, boundary layer analysis, and time-dependent flow analysis, including problems involving relative motion, are discussed in some detail. The code is written in Fortran77, using adjustable-size arrays so that it can be easily redimensioned to match problem requirements and computer hardware constraints. An overview of the program input is presented. A detailed description of the input parameters is provided in the appendices. PMARC results for several test cases are presented along with analytic or experimental data, where available. The input files for these test cases are given in the appendices. PMARC currently supports plotfile output formats for several commercially available graphics packages. The supported graphics packages are Plot3D, Tecplot, and PmarcViewer.

Ashby, Dale L.↗

NASA NTRS2007

Boundary Layer Development on a Turbine Blade in a Linear Cascade

Several different boundary-layer development patterns for flow over the suction surface of a turbine airfoil in a linear cascade were studied and documented using a sliding surface hot-film sensor. The state of the boundary layer, whether laminar, transitional or turbulent, was determined at numerous locations along the airfoil suction surface from leading to trailing edge. Boundary-layer transition from laminar to turbulent flow through laminar separation and turbulent reattachment, or through a combination of bypass transition and strong and weak separation and turbulent reattachment, or through solely bypass transition without separation, was observed and benchmark data were recorded. Surface flow visualization and numerical boundary-layer analysis results are consistent with the hot-film data. Flow and geometry information necessary for nmerical code operation is available.

Halstead, Dave↗