Results for “canister” — Page 7

DOE OSTI2024

Magnetostrictive EMAT for Nuclear Spent Fuel Canisters

One approach for mitigation of stainless steel (SS) spent fuel canisters (SFCs) is to coat the welds or even the entire SFC with a cold-sprayed nickel coating. The coating can serve as a magnetostrictive interface between an electromagnetic acoustic transducer (EMAT) and the SS plate material. The EMAT can send ultrasound into the canister and “listen” for reflections caused by chloride-initiated stress corrosion cracking (CISCC) or other damage mechanisms that may lead to leaks if undetected and unmitigated. Here, this project outlines an approach for monitoring the integrity of SFCs using magnetostrictive EMAT sensors, which emit and detect discontinuity-initiated reflections indicative of pits or cracks likely arising from CISCC. Flat 13 mm SS plates with welds similar to actual canister welds were prepared, with flat-bottom holes 3 mm and 6 mm deep and 6 mm in diameter placed within the weld heat-affected zone (HAZ). The most effective sensor configurations were able to detect critical discontinuities more than 2 m away. Although a single sensor could be robotically deployed, the large volume covered by each sensor could support a small number of permanently mounted sensors, equipped with an external connector for periodic interrogation. The HAZ of a hypothetical SFC cylindrical surface could be effectively monitored with just 16 sensors.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRSDate not supplied

Development, Build and Certification of the Alternate Fecal Canister (AFC) Hardware for the NASA Exploration Toilet

On longer range exploration missions, the mass and volume of critical hardware and consumables that will be needed to support crew will pose a big stowage challenge. This includes the hardware needed for the collection and storage of human metabolic waste. The amount of stowage needed for this hardware both before (empty) and after (full) use will be a significant burden on the overall spacecraft habitable volume, layout, and design. To help with this challenge, the National Aeronautics and Space Administration (NASA) has developed a collapsible canister for the collection and containment of fecal deposits. The Alternate Fecal Canister (AFC) is an alternative to the exploration toilet hard-sided fecal canister. The AFC is collapsible in its empty state which is a volume benefit to smaller vehicles on longer missions. In addition, the use of lighter-weight materials provides a reduction in mass of the overall container. This paper will provide a summary of the AFC design including final flight design and build, acceptance and qualification testing completed, final certification and delivery and forward plans for a technology demonstration with the exploration toilet on the International Space Station (ISS). In addition, a summary of issues and final resolution encountered during flight build and testing will also be provided. As part of the acceptance and certification process for AFC, the hardware was also put into several rounds of odor testing with the support of the White Sands Test Facility (WSTF). The details, planning and anomalies identified during odor testing will also be summarized in this paper. Finally, a brief overview of potential future design upgrades including changes to address any crew feedback from the ISS demonstration will be discussed.

Fecal Canister↗

NASA NTRSDate not supplied

Development, Build and Certification of the Alternate Fecal Canister (AFC) Hardware for the NASA Exploration Toilet

On longer range exploration missions, the mass and volume of critical hardware and consumables that will be needed to support crew will pose a big stowage challenge. This includes the hardware needed for the collection and storage of human metabolic waste. The amount of stowage needed for this hardware both before (empty) and after (full) use will be a significant burden on the overall spacecraft habitable volume, layout, and design. To help with this challenge, the National Aeronautics and Space Administration (NASA) has developed a collapsible canister for the collection and containment of fecal deposits. The Alternate Fecal Canister (AFC) is an alternative to the exploration toilet hard-sided fecal canister. The AFC is collapsible in its empty state which is a volume benefit to smaller vehicles on longer missions. In addition, the use of lighter-weight materials provides a reduction in mass of the overall container. This paper will provide a summary of the AFC design including final flight design and build, acceptance and qualification testing completed, final certification and delivery and forward plans for a technology demonstration with the exploration toilet on the International Space Station (ISS). In addition, a summary of issues and final resolution encountered during flight build and testing will also be provided. As part of the acceptance and certification process for AFC, the hardware was also put into several rounds of odor testing with the support of the White Sands Test Facility (WSTF). The details, planning and anomalies identified during odor testing will also be summarized in this paper. Finally, a brief overview of potential future design upgrades including changes to address any crew feedback from the ISS demonstration will be discussed.

Fecal Canister↗

NASA NTRSDate not supplied

Development, Build and Certification of the Alternate Fecal Canister (AFC) Hardware for the NASA Exploration Toilet

On longer range exploration missions, the mass and volume of critical hardware and consumables that will be needed to support crew will pose a big stowage challenge. This includes the hardware needed for the collection and storage of human metabolic waste. The amount of stowage needed for this hardware both before (empty) and after (full) use will be a significant burden on the overall spacecraft habitable volume, layout, and design. To help with this challenge, the National Aeronautics and Space Administration (NASA) has developed a collapsible canister for the collection and containment of fecal deposits. The Alternate Fecal Canister (AFC) is an alternative to the exploration toilet hard-sided fecal canister. The AFC is collapsible in its empty state which is a volume benefit to smaller vehicles on longer missions. In addition, the use of lighter-weight materials provides a reduction in mass of the overall container. This paper will provide a summary of the AFC design including final flight design and build, acceptance and qualification testing completed, final certification and delivery and forward plans for a technology demonstration with the exploration toilet on the International Space Station (ISS). In addition, a summary of issues and final resolution encountered during flight build and testing will also be provided. As part of the acceptance and certification process for AFC, the hardware was also put into several rounds of odor testing with the support of the White Sands Test Facility (WSTF). The details, planning and anomalies identified during odor testing will also be summarized in this paper. Finally, a brief overview of potential future design upgrades including changes to address any crew feedback from the ISS demonstration will be discussed.

Fecal Canister↗

DOE OSTI2023

Bounding Pressure and Flammability Evaluations for a Department of Energy Standard Canister Loaded with Aluminum-Clad Spent Fuel

This report presents bounding pressurization and flammability evaluations from the radiolytic gas generation expected during extended (>50 years) dry storage of aluminum-clad spent nuclear fuel (ASNF) elements in a sealed Department of Energy (DOE) Standard Canister. The primary questions involving extended ASNF dry storage center around the adequacy of dry storage conditioning processes (i.e., drying) and the behavior of residual hydrated aluminum oxides on the cladding—specifically, the radiolytic breakdown of chemically bound water in these corrosion products. The objectives of the presented work include providing a bounding assessment of the pressure with respect to the DOE Standard Canister’s structural integrity limits and identifying the potential for forming flammable or explosive gas mixtures (i.e., exceedance of the lower flammability limit of the molecular hydrogen [H2] and oxygen [O2] concentrations). The evaluation results confirm the findings of previous, more complex M&S work. That is, the structural integrity of the canister remains unchallenged by a wide margin. Nevertheless, it is important to recognize that the presented pressure calculations consider a full breakdown of the chemisorbed water, including a consequent release of all available H2. In reality, the breakdown of water in these systems will likely remain incomplete, due to competing chemical and radiolytic reactions, thereby attaining an equilibrium in the storage environment.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2023

Long-term sinking of nuclear waste canisters in salt formations by low-stress creep at high temperature

Abstract Rock salt has a self-sealing capacity, low permeability, and high thermal conductivity, making it a potential host for heat-generating nuclear waste. The feasibility of nuclear waste disposal within salt formations has been investigated mostly for small-sized canisters. Geologic disposal of larger-sized canisters originally designed for spent fuel storage and transportation has lately been examined as a cost-effective alternative. This raises questions about their long-term vertical movement due to their weight and high decay heat. Low-stress creep governs this movement; however, most salt constitutive models do not incorporate it. In this paper, the Norton and the WIPP creep models are compared with the Lux/Wolters/Lerche (LWL) model and a simpler model that combines linear and Norton creep laws (named combined creep model). The LWL and combined creep models consider pressure solution creep, though all incorporate dislocation creep. The models are first applied to creep tests under various stress levels. The LWL and the combined creep models results fit the experimental data well in both high and low stress ranges, whereas the Norton and WIPP models results only fit in higher-stress ranges. The different models are further applied for analyzing long-term canister movement. A sinking rate of $$-4.4\times 10^{-7}$$ - 4.4 × 10 - 7 mm/year was predicted using the Norton and WIPP models versus $$-2.1\times 10^{-2}$$ - 2.1 × 10 - 2 mm/year and $$-3.1\times 10^{-2}$$ - 3.1 × 10 - 2 mm/year using the LWL and the combined creep models, respectively. This comparative study confirms that creep models calibrated exclusively against high-deviatoric stress data might result in an inaccurate estimation of waste packages sinking rate in salt formations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

Large Plate Experiment of Chloride-induced Stress Corrosion Cracking in Spent Nuclear Fuel Storage Canisters

This report provides a description of the testing (in progress at the Savannah River National Laboratory) to evaluate the corrosion behavior of a large section of welded plate material harvested from the Sandia National Laboratories’ full-size mockup of a spent nuclear fuel (SNF) dry storage canister. The details of the establishment of this plate test, the interim corrosion results (from visual examination), and the general plan for examination of the plate in CY21 to evaluate crack growth behavior (if any) are provided. This work is intended to inform aging management programs for SNF canisters under conditions of extended dry storage. A “large plate” (approximately 51 x 46 cm with thickness 16 mm and weight about 30 kg) and containing a circumferential weldment from the mockup is the test specimen. The knowledge of the salt, temperature, humidity conditions for chloride-induced stress corrosion cracking (CISCC) including the threshold stress intensity factor, K iscc , were used to setup the large plate test in which a set of part-through-wall and through-wall electrical discharge machined (EDM) defects were positioned in the weld residual stress field of the welded plate material from the mockup canister. A marine salt solution was applied to this plate specimen with an air-brush spray, then dried, and then exposed to a sustained 71-73% RH condition at an ambient room temperature of 22 °C. The salt loading and environmental condition is expected to be aggressive to cause CISCC

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

Preliminary Test Design and Plan for a Canister Deposition Field Demonstration

This report provides a high-level test plan for deploying three commercial 32PTH2 spent nuclear fuel (SNF) canisters inside NUHOMS Advanced Horizontal Storage Modules (AHSM) from Orano (formerly Transnuclear Inc.). The details contained in this report represent the best designs and approaches explored for testing as of this publication. Given the rapidly developing nature of this test program, some of these plans may change to accommodate new objectives or adapt in response to conflicting requirements. The goal of the testing is to collect highly defensible and detailed surface deposition measurements from the surface of dry storage systems in a marine coastal environment to guide chloride-induced stress corrosion crack (CISCC) research. To facilitate surface sampling, the otherwise highly prototypic dry storage systems will not contain SNF but rather will be electrically heated to mimic the thermal-hydraulic environment. Instrumentation throughout the canister, storage module, and environment will provide an extensive amount of information for the use of model validation. Manual sampling over a comprehensive portion of the canister surface at regular time intervals will offer a high-fidelity quantification of the conditions experienced in a harsh yet realistic environment.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2021

SNF Interim Storage Canister Corrosion and Surface Environment Investigations (FY21 Status Report)

This progress report describes work performed during FY21 at Sandia National Laboratories (SNL) to assess the localized corrosion performance of canister materials used in the interim storage of spent nuclear fuel (SNF). Of particular concern is stress corrosion cracking (SCC), by which a through-wall crack could potentially form in a canister outer wall over time intervals that are shorter than possible dry storage times. In FY21, modeling and experimental work was performed that further defined our understanding of the potential chemical and physical environment present on canister surfaces at both marine and inland sites. Research also evaluated the relationship between the environment and the rate, extent, and morphology of corrosion, as well as the corrosion processes that occur. Finally, crack growth rate testing under relevant environmental conditions was initiated.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2021

Dual-Purpose Canister Filling Demonstration Project Progress Report

This report discusses the progress made at the Oak Ridge National Laboratory to support direct disposal of dual-purpose canisters (DPCs). Acceptable filler materials should demonstrate that the probability of criticality in DPCs during the disposal timeframe is below the probability threshold for inclusion in a repository performance assessment. This effort, which will ultimately result in a full-scale demonstration, includes computational fluid dynamics (CFD) modelling developed to gauge the filling process and to uncover any unforeseen issues. Filling simulations of the lower region (mouse holes) of a prototypic DPC show successfully simulate filling of the void space inside the canister and a smooth, even progression of the liquid level. Flow through a pipe that is similar to the drainpipe in a DPC is being investigated separately to gain valuable insight of the flow regime inside a pipe. Three physical experiments validating the computational filling model have been completed using surrogate liquids. One experiment using molten metal has been completed and the results demonstrate adequate filling of the canister void spaces. Although the scale experiment observed some void spaces related to shrinkage of the metal during cooling, the volume filled is expected to be sufficient to meet the purpose of moderator exclusion. Further experiments will scale up the geometry, moving towards a full-sized DPC demonstration, and provide a more rigorous investigation of candidate filler materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Cold Spray for Mitigation and Repair of Spent Nuclear Fuel Dry Storage Canisters

The purpose of this work is to investigate the use of cold spray for repair and mitigation of chloride-induced stress corrosion cracking (CISCC) in dry cask storage system (DCSS) canisters to ensure their integrity far beyond their original license period. This report provides a viability analysis of cold spray for repair and mitigation of CISCC in DCSS canisters to extend canister life.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2022

FY2022 Status Update: A Probabilistic Model for Stress Corrosion Cracking of SNF Dry Storage Canisters

Understanding the potential risk of stress corrosion cracking of spent nuclear fuel dry storage canisters has been identified as a knowledge gap for determining the safety of long-term interim storage of spent nuclear fuel. To address this, the DOE is funding a multi-lab DOE effort to understand the timing, occurrence, and consequences of potential canister SCC. Sandia National Laboratories has developed a probabilistic model for canister penetration by SCC. This model has been continuously updated at SNL since 2014. Model uncertainties are treated using a nested loop structure, where the outer loop accounts for uncertainties due to lack of data and the inner aleatoric loop accounts for uncertainties due to variation in nature. By separating uncertainties into these categories, it is possible to focus future work on reducing the most influential epistemic uncertainties. Several experimental studies have already been performed to improve the modeling approach through expanded process understanding and improved model parameterization. The resulting code is physics-based and intended to inform future work by identifying (1) important modeling assumptions, (2) experimental data needs, and (3) necessary model developments. In this document, several of the sub-models in the probabilistic SCC model have been exercised, and the intermediate results, as the model progresses from one sub-model to the next, are presented. Evaluating the sub-models in this manner provides a better understanding of sub-model outputs and has identified several unintended consequences of model assumptions or parameterizations, requiring updates to the modeling approach. The following updates have been made, and future updates have been identified.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2022

Measurement of radiolytic hydrogen generation from surrogate zr-based materials in a "mini-canister"

This report describes a test campaign to investigate radiolytic hydrogen generation from surrogate materials resembling the (Zr-based) cladding of commercial spent nuclear fuel (SNF) with an inventory of residual water post-dryout. The radiolytic hydrogen generation rates from residual waters in the SNF-in-canister system are important for predicting the in-canister environment for sealed SNF dry storage canisters over time and the impact to continued safe dry storage.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Validation of Thermohydraulic Simulations using RELAP for Critical Dual Purpose Canisters

Simulations using the RELAP5-3D systems analysis code and STAR-CCM+, a high-fidelity CFD code, were performed on a model of a real-scale MPC-32 dual purpose canister undergoing a criticality event. These simulations were performed to provide code-to-code verification of the natural convection capabilities in RELAP5. The STAR-CCM+ simulations revealed various natural convection flow patterns that aided in the cooling of fission heat produced in the fuel rods in the canister. Negligible spatial temperature variations were observed across the canister in the STAR-CCM+ results, supporting the use of RELAP5 in predicting the sub-cooled regime. The surface-averaged rod temperature predicted by RELAP5 compared well with STAR-CCM+, verifying the predictive capability of RELAP5 for sub-cooled conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Residual Stresses in Spent Nuclear Fuel Storage Canisters with Cold Spray Coatings

This report describes the development of cold spray (CS) process and its application to provide on overlay coating of metal welds with a surface crack in a spent nuclear fuel (SNF) storage canister and thereby remediate the canister from further propagation of the crack. This work informs aging management programs for the SNF canisters.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

FY23 Update: Aerosol Sampling for the Canister Deposition Field Demonstration

This report describes the results of preliminary testing of aerosol monitoring equipment that will be used to continuously monitor the aerosol source term for the multi-year Canister Deposition Field Demonstration (CDFD). These data are required inputs for the development and validation of models for the deposition of dust and potentially corrosive salts on the surface of spent nuclear fuel (SNF) dry storage canisters. Surface salt loads correlate with the extent of corrosion damage on a metal surface, and potentially to the likelihood and timing of initiation of stress corrosion cracks. Aerosols will be monitored at the CDFD site using three instruments. A Dekati ® ELPI+ cascade impactor will be used for real-time monitoring of aerosol particle sizes. It will also collect dust in 14 size bins on impactor targets that can be chemically analyzed to determine the soluble salts present as a function of particle size. However, this instrument can only measure dried aerosols, with a diameter of <10 µm. The second instrument is a Topas laser particle size spectrometer, which provides real-time monitoring of aerosol particle sizes up to ~40 µm in size. It monitors both the ambient (potentially deliquesced) aerosol particle size distributions required for the dust deposition models and the distributions of the equivalent dried particles, allowing correlation with the Dekati ® data. However, it does not discriminate between inert dust particles and salt aerosols, and it does not retain samples of the different particle sizes for later analysis. The third instrument that will monitor aerosols at the CDFD site is a Clean Air Status and Trends Network (CASTNET) tower, which uses a multiple canister system to collect weekly samples for analysis to total suspended aerosol particle compositions and atmospheric gas concentrations. This status report describes work in FY23 to develop the capabilities for using these tools. In two training exercises, the cascade impactor and laser particle sizer were deployed in two different testing environments, one indoor and one outdoor. For the cascade impactor, the tests provided opportunities for the operators to familiarize themselves with impactor substrate preparation, and post-test sample removal and analysis. For the laser particle sizer, the tests were used to evaluate different instrument parameters, to determine the most appropriate settings for capturing transient events. Data and samples were collected for weeks to months for each test, and the results are presented here. In addition to the preliminary testing, contracts were developed with WSP Analytical Labs for sample preparation and analysis of the cascade impactor samples. The impactor tower from outdoor test was delivered to WSP and used to train the staff there in disassembly, sample extraction, sample analysis, and tower reassembly with new target substrates. These are tasks that WSP will be performing routinely for the CDFD project. The CASTNET system cannot be purchased or tested until an actual site has been selected for the CDFD test. Work for this FY has been restricted to preparation of contracts for purchasing the CASTNET tower, and for sample analysis, once the tower is in operation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Assessing the release, transport, and retention of radioactive aerosols from hypothetical breaches in spent fuel storage canisters

Interim dry storage of spent nuclear fuel involves storing the fuel in welded stainless-steel canisters. Under certain conditions, the canisters could be subjected to environments that may promote stress corrosion cracking leading to a risk of breach and release of aerosol-sized particulate from the interior of the canister to the external environment through the crack. Research is currently under way by several laboratories to better understand the formation and propagation of stress corrosion cracks, however little work has been done to quantitatively assess the potential aerosol release. The purpose of the present work is to introduce a reliable generic numerical model for prediction of aerosol transport, deposition, and plugging in leak paths similar to stress corrosion cracks, while accounting for potential plugging from particle deposition. The model is dynamic (changing leak path geometry due to plugging) and it relies on the numerical solution of the aerosol transport equation in one dimension using finite differences. The model’s capabilities were also incorporated into a Graphical User Interface (GUI) that was developed to enhance user accessibility. Model validation efforts presented in this paper compare the model’s predictions with recent experimental data from Sandia National Laboratories (SNL) and results available in literature. We expect this model to improve the accuracy of consequence assessments and reduce the uncertainty of radiological consequence estimations in the remote event of a through-wall breach in dry cask storage systems.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRS1971

A motor canister designed for prolonged operation in space

A special canister was designed to protest the dc motors used on the ISIS 1 antenna unit. The canister is provided with a pressure-monitoring device and has a special shaft seal that imparts minimum load to the motor output shaft. The development and flight testing of the canister are discussed. Problems that were encountered during fabrication and inspection and the problems caused by material/lubricant incompatibility and low temperature are also discussed.

Wells, A.↗