Search NASA⌕ Search

SEARCH · Search NASA

Results for “carpet”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

121 records · Page 7

Secondary Sonic Boom Ray Path Prediction using sBOOM

Sonic boom ray path equations are solved numerically to show the extent of secondary booms compared to primary sonic boom carpet. Secondary booms are shown to reach altitudes of ~125 km before turning toward the ground and impinging at lateral distances of ~50 km and beyond. Exact closed-form solutions of the ray paths and their partial derivatives with respect to certain relevant parameters are derived for the simplified case of windless atmospheres and compared against numerical solutions. Ray tube areas are computed using the Jacobian of a single ray as opposed to the traditional technique of using 4 rays that are temporally and azimuthally perturbed. The ray tube areas corresponding to secondary booms can get 1000 times larger than those from primary booms. The numerically computed ray tube areas are verified using exact expressions for the special case of windless atmospheres. Finally, pressure scaling due to ray tube area changes and atmospheric stratification is presented and the shortcomings associated with the current atmospheric interpolation techniques are discussed. It is determined that piece-wise linear interpolation of the atmospheric temperature may be inadequate and could lead to numerical noise in the prediction of secondary booms.

Sriram K Rallabhandi↗

X-59 Sonic Boom Test Results from the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel

A wind tunnel test was conducted to investigate near-field sonic boom pressure signatures from a model of the X-59 Low-Boom Flight Demonstrator aircraft. A 1.62%-scale model of the aircraft in the C612A configuration was fabricated for the wind tunnel test, which took place in the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel in September and October 2021. The model had provisions for two different mounting options: a swept blade strut that attached at the top of model ahead of the inlet, and rear-entry sting that was made as one piece with a dummy nacelle, and which had a 2”-long cylindrical segment aft of the nozzle exit before tapering up in size. The blade strut allowed for a clean aft end of the model for evaluation of the shocks from that region, while the sting avoided the significant distortions of the flow and shocks from the blade strut along the top of the model. Both the sting and the strut had adapters that attached to a force balance. The model had alternate parts for ±0.5° deflections of the flaps, ailerons, and stabilator, and ±1° deflections of the T-tail horizontal surface. Off-body static pressure measurements of the flow field below the model were made by use of a pressure rail which had 420 orifices along its tip. The model was positioned at various heights from the rail by vertical movement of the wind tunnel strut, and at various longitudinal stations relative to the rail by means of a linear actuator mounted between the tunnel strut and the balance. The longitudinal positioning allowed multiple pressure signatures to be obtained along different portions of the rail. These signatures were aligned by accounting for the model longitudinal movement and then averaged to take out the effects of tunnel flow distortions and the interference of the rail flow field and shocks on the model pressure signatures. The test was run at approximate Mach numbers of 1.36, 1.4, and 1.47, and the model was set at various angles of attack and roll relative to the rail. Plots of the model signatures for all the variations of Mach number, model angles, control deflections, and height relative to the rail are provided throughout the report. Repeatability was generally very good and gave confidence in the quality of the measurements. The signatures measured at various heights from the rail provided insight into the aging of the model shocks as they propagated from 1.2 to 3 body lengths from the model. Off-track signatures up to 45° from centerline obtained by rolling the model gave indications of the shock flow fields across the width of the sonic boom carpet. The deflections of the various control surfaces allowed assessment of the boom sensitivity to the control surface movements.

Sonic boom↗

X-59 Sonic Boom Test Results from the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel

A wind tunnel test was conducted to investigate near-field sonic boom pressure signatures of the X-59 Low-Boom Flight Demonstrator aircraft. A 1.62%-scale model of the aircraft was fabricated for the wind tunnel test, which took place in the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel in September and October 2021. The model had provisions for being mounted by a swept blade strut that attached at top of model ahead of the inlet, or by a rear-entry sting that held the model at the location of the nacelle. The model had alternate parts for ±0.5° deflections of the flaps, ailerons, and stabilator, and ±1° deflections of the T-tail. Off-body static pressure measurements of the flow field below the model were made on a pressure rail which had 420 orifices along its tip. The model was positioned at various heights from the rail by vertical movement of the tunnel strut, and at various longitudinal stations relative to the rail by means of a linear actuator mounted between the wind tunnel strut and the balance. Spatial averaging of model pressure signatures acquired over a range of longitudinal positions reduced the effects of tunnel flow distortions and the interference of the rail flow field and shocks on the model pressure signatures. The test was run at approximate Mach numbers of 1.36, 1.4, and 1.47, and the model was set at various angles of attack and roll relative to the rail. Plots of the model signatures for representative variations of Mach number, model angles, control deflections, and height relative to the rail are provided throughout the report. Repeatability was generally very good and gave confidence in the quality of the measurements. The signatures measured at various heights from the rail provided insight into the aging of the model shocks as they propagated from 1.2 to 3 body lengths from the model. Off-track signatures up to 45° from centerline obtained by rolling the model gave indications of the shock flow fields across the width of the sonic boom carpet. The deflections of the various control surfaces allowed assessment of the boom sensitivity to the control surface movements.

Sonic boom↗

Split-Step Simulations to Assess the Effects of Atmospheric Boundary Layer Turbulence on the Dose Variability of N-Waves and Shaped Booms

The effects of atmospheric boundary layer turbulence on the loudness variability of a sonic boom N-wave and shaped boom are examined with split-step simulations. The shaped boom is representative of a design iteration of the NASA X-59 aircraft. Inhomogeneous atmospheric boundary layer turbulence is generated in the computational domain by a Fourier synthesis method. The N-wave and shaped boom are propagated through turbulent fields representing eight different convection levels measured at the NASA Kennedy Space Center and the NASA Armstrong Flight Research Center. Probability density functions of the formation of caustic regions along the propagation direction are computed from the N-wave results, and a parameter to collapse the caustic PDFs that accounts for both fluctuation intensities and length scales is proposed. Statistical results concerning loudness metric variability are presented, and the standard deviations of several metrics are shown to collapse across different convection levels of turbulence for small nondimensional propagation distances. The loudness metric distributions are observed to be well approximated by a normal distribution for a given range of propagation distances, and become increasingly skewed as distance increases. A model function for the dose variability is proposed, and the function parameters are found to be related to the convection level of the turbulence. The model for the dose variability distribution is compared to simulation data that were not used to find the regression parameters of the model. At several nondimensional propagation distances, agreement is observed between the model and the simulation data. These results indicate that the model may be suitable for providing quick estimates of noise dose variability in the primary carpet region across a wide range of atmospheric boundary layer conditions.

Sonic boom↗

X-59 Sonic Boom Test Results from the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel

A wind tunnel test was conducted to investigate near-field sonic boom pressure signatures of the X-59 Low-Boom Flight Demonstrator aircraft. A 1.62%-scale model of the aircraft was fabricated for the wind tunnel test, which took place in the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel in September and October 2021. The model had provisions for being mounted by a swept blade strut that attached at top of model ahead of the inlet, or by a rear-entry sting that held the model at the location of the nacelle. The model had alternate parts for ±0.5° deflections of the flaps, ailerons, and stabilator, and ±1° deflections of the T-tail. Off-body static pressure measurements of the flow field below the model were made on a pressure rail which had 420 orifices along its tip. The model was positioned at various heights from the rail by vertical movement of the tunnel strut, and at various longitudinal stations relative to the rail by means of a linear actuator mounted between the wind tunnel strut and the balance. Spatial averaging of model pressure signatures acquired over a range of longitudinal positions reduced the effects of tunnel flow distortions and the interference of the rail flow field and shocks on the model pressure signatures. The test was run at approximate Mach numbers of 1.36, 1.4, and 1.47, and the model was set at various angles of attack and roll relative to the rail. Plots of the model signatures for representative variations of Mach number, model angles, control deflections, and height relative to the rail are provided throughout the report. Repeatability was generally very good and gave confidence in the quality of the measurements. The signatures measured at various heights from the rail provided insight into the aging of the model shocks as they propagated from 1.2 to 3 body lengths from the model. Off-track signatures up to 45° from centerline obtained by rolling the model gave indications of the shock flow fields across the width of the sonic boom carpet. The deflections of the various control surfaces allowed assessment of the boom sensitivity to the control surface movements.

Sonic boom↗

Supersonic Flight Testing to Assess Ground Recording Systems for NASA's Low Boom Flight Demonstrator

The National Aeronautics and Space Administration (NASA) has performed two supersonic flight test campaigns in preparation for the extensive ground measurements that will be taken during Quesst Phase 2 to verify the low boom from the X-59. The first test campaign was Carpet Determination In Entirety Measurements (CarpetDIEM) Phase II, with F/A-18B aircraft and a subscale ground sensor array and the second campaign was CarpetDIEM Phase III,with both F-15B and F/A-18D aircraft and a geographically large scale ground sensor array. CarpetDIEM Phase II served to evaluate prototypes of the state-of-the-art Ground Recording System (GRS) which NASA is developing in order to record the low boom of X-59. The prototype GRS measured both N-wave and evanescent wave sonic booms which were1.4±1.1PLdB from co-located truth sources during these flights. CarpetDIEM Phase II was also used to down select two NASA developed unattended trigger concepts, one based on Automatic Dependent Surveillance-Broadcast (ADS-B) and the other utilizing satellite communications. Both unattended trigger concepts performed well, with the ADS-B based concept being chosen at the conclusion of CarpetDIEM Phase II for integration with the GRS. CarpetDIEM Phase III was primarily a logistics risk-reduction effort for Quesst Phase 2, but also sought to evaluate the capabilities, including the newly implemented ADS-B unattended trigger, and ruggedness of the GRS during a long-term deployment. The F-15B stood in for the X-59, flying two different X-59flight profiles, including an accelerating climb maneuver. The GRS successfully self-triggered to capture 80% of sonic booms generated from both steady and dynamic flight maneuvers. Low booms, defined by the project as being≤80 PLdB, were recorded by the GRS near the end of CarpetDIEM Phase III. The GRS measured low booms were found to be within0.4±0.1PLdB of a co-located truth source.

Forrest L Carpenter IV↗

Enhancing Nasa Sounding Rocket Capabilities Through Composite Material Adoption

Sounding rockets are a suborbital research platform employed by NASA for heliophysics, astrophysics, and geospace science investigations, and for technology development. They follow semi-parabolic trajectories and are launched using surplus military, and commercial, solid-propellant rocket motors. NASA sounding rocket payloads are comprised of standard, modular subassemblies, designed to perform specific functions critical to achieving mission success criteria. Since the program’s inception, payload length and mass have trended upwards, limiting the capability of the platform to reach exospheric apogees and decreasing the time above critical altitudes to observe solar and celestial targets. To offset this trend, composite materials may be of use in payload and subsystem design to decrease payload mass. This investigation seeks to understand if there is a practical benefit to introducing composite materials on the NSRP by assessing mission specific impacts to those missions conducted in fiscal year 2024. To accurately estimate the mass of a composites-based payload, a standard subsystem (NIACS) underwent structural reconfiguration. Materials were selected that align with NSRP design, manufacturing, and testing standards. NIACS reconfiguration resulted in a mass reduction of 19.6% which was then applied to the payload system in entirety. Using vehicle performance carpet plots, delta apogee and time above the Kármán line were determined. Performance improvements were then evaluated against that mission’s success criteria to determine if that mission would have benefitted from using composite materials. On average, each mission would have gained 59.8 kilometers apogee and 62.9 seconds above the Kármán line. However, only nine of the seventeen missions would have benefitted from these performance improvements. Two of the missions could have used a lower-impulse launch vehicle to achieve mission success. Upleg stability met programmatic criteria; downleg instability and dynamic pressure improved, showing that ballast would not offset the mass reduction of using composite materials. Cost analysis showed that production costs will increase 39%. For the two missions that could have used a lower-impulse launch vehicle, the cost of the launch vehicle would have offset payload production costs. In summary, composite materials are not recommended for universal use on NASA sounding rocket payloads due to unclear programmatic benefits and added cost. However, they are justified for optical astrophysics and heliophysics missions, high-apogee (exosphere) requirements, or when they reduce payload costs versus higher impulse launch vehicles. Reflown, recoverable subsystems should use composites to enhance apogee and observation time.

Robert Henry Burth↗

DOE Zero Energy Ready Home Case Study HIA 2021: Insight Homes, The Brenner, Felton, DE

Case study of a DOE 2021 Housing Innovation Award winning custom home in a mixed-humid climate that got a HERS 51 without PV, with 1,940 square feet, MERV 13 filters and low-emission paints, adhesives, and carpeting; plus a sealed, conditioned crawl space, and a high-efficiency gas furnace and heat pump.

Building America, residential construction, home b↗

Analysis of Material Properties of Aged Rigid Polyurethane Foam

Foams are classified as either rigid or flexible and are commonly used in applications such as pipe insulation, carpet fibers, and chair foam cushions. Polyurethane foams are excellent thermal insulators, have excellent mechanical properties, and are chemically inert. With the addition of fire protective additives, polyurethane foams have the ability to intumescence when exposed to high temperatures. For the future storage of the 9977 nuclear shipping packages, the material properties of the General Plastics 3716 rigid polyurethane foam were evaluated for long term performance by comparing aged samples to unaged samples. General Plastics 3716 rigid polyurethane foam was aged from November 2014 to June 2019 at varying temperatures of: 160 deg. F, 160 deg. F + 50% relative humidity (RH), 185 deg. F, 215 deg. F, and 250 deg. F. The foam was then analyzed via Fourier Transform Infrared Spectroscopy (FTIR), 3D Optical Microscope, Thermal Gravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC). FTIR and Optical Microscope: No significant change to chemical or physical structure was evident by FTIR or optical microscope analysis. DSC: Decrease of heat capacity over time for all oven temperatures except a slight increase for the 185 deg. F conditioned foams. Largest decrease evident with foams conditioned at 250 deg. F. A slight increase in heat capacity for humid samples. Similar trends in heat capacities at 71 deg. C and 102 deg. C. TGA: As conditioning temperature increased, a decline was evident in the average percent weight loss, onset temperature, and first derivative peak temperature. No significant effect due to humidity except for a decrease in first derivative peak temperature. Unaged samples exhibited strong intumescence. Foams conditioned at 160 deg. F exhibited slight intumescence. Results suggest fire protective additives decomposed at higher temperatures, which contributed to a lower average percent mass loss in higher temperature conditioning. Further thermal degradation testing would be beneficial to evaluate the ability of the conditioned foams to intumesce. Evaluate irradiation dose rate effects on conditioned foam. Possible conditioning in an environment with a known humidity or analyzing a new aliquot of sample for each trial to achieve a more representative heat capacity calculation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

X-ray Irradiance Distribution for an Interferometer with a Curved Biprism Array

The development of interferometry-based X-ray phase contrast imaging systems that provide highly resolved X-rays with spatially-modulated intensity is enabling the full potential of X-ray optics to image phase, attenuation, and small angle scatter properties of soft tissue. In this work we present analytical formulations of a new hardware concept for X-ray phase contrast imaging wherein the phase grating is replaced with an array of Fresnel biprisms. We derive expressions for the irradiance distribution pattern of a biprism interferometer composed of a curved biprism array with multiple biprisms and multiple point sources. These expressions are used to plot fringe patterns for X-ray design parameters, including 1) size, number, and period of X-ray point sources; 2) biprism parameters of material composition, angle, number, and period; and 3) biprism array to X-ray source and detector distances. Analytical results show that the biprism interferometer provides a longitudinally-nonperiodic pattern of spatially modulated intensity different from the Talbot longitudinally-periodic pattern common in grating interferometry. The curvature of the biprism array brings a sharper longitudinal fringe pattern. Experiments are being performed to verify the analytical calculations for a biprism plastic material of SU-8 using a synchrotron source. X-ray biprism material has widely varied indexes of refraction relative to wavelength and thus the separation of the virtual sources and resulting interference fringe period also varies with X-ray wavelength. Our aim is to develop biprism interferometry imaging systems with excellent polychromatic performance that produce high-contrast fringes with spatially incoherent X-ray illumination. Biprism interferometry will potentially provide higher fringe visibility with better image quality to that of diffraction grating interferometry.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Simulations and case study of X-59 low-booms propagated through measured atmospheric profiles

NASA's X-59 Quiet Supersonic Technology aircraft will soon be used to collect data to support the development of a dose-response relationship between low-boom level and human perception. The X-59's low-boom level will depend on aircraft conditions and trajectory, which can be controlled, and on atmospheric conditions, which cannot be controlled. To assess variability in low-boom levels produced by realistic atmospheres, NASA's PCBoom code was used to simulate propagation of an X-59 nearfield pressure condition through atmospheric profiles measured during NASA's Quiet Supersonic Flights 2018 (QSF18) test. Despite QSF18 lasting only 11 days, substantial weather variability occurred including snow and record high temperatures. A PL range of about 8.5 dB was predicted due to the QSF18 atmospheric variability. These results demonstrate the necessity for X-59's flight condition to be adjusted based on atmospheric conditions in order to achieve desired loudness levels during community surveys. Undertrack booms' Perceived Levels (PL) were predicted not to exceed 75 dB, X-59's target level in a standard atmosphere. Attenuation rate, ray tube area, path length, and other quantities are presented throughout propagation for the atmospheres that produce the loudest and quietest booms. Humidity differences below 15kft were a primary driver of the PL differences.

X-59↗

Optimal Mission Profile for Low-Boom Supersonic Aircraft

An optimal mission profile, called the low-boom mission profile, is proposed for low-boom supersonic aircraft. The low-boom mission profile uses a fixed AoA for the cruise segment until reaching the cruise ceiling. The fixed AoA is determined by the cruise condition for the low-boom shaping of the aircraft. The derived CL trajectory is not necessarily the optimal trajectory for the cruise range when unrestricted supersonic flight is allowed. The undertrack sonic boom ground noise level is reduced during the cruise because of the increasing altitude from the fixed AoA trajectory and the approximate invariance of nondimensional overpressure at 3BL below a supersonic aircraft with respect to cruise altitude change when the AoA and cruise Mach are fixed. The approximate invariance of nondimensional overpressure at 3BL below a supersonic aircraft is verified using both Euler and Reynolds-averaged Navier-Stokes CFD solvers. A low-boom supersonic transport concept is used to illustrate that, compared to the fixed cruise altitude trajectory, the low-boom mission profile can increase the cruise range of a low-boom aircraft and reduce the undertrack sonic boom ground noise levels for the entire cruise segment. One significant contribution of this paper is the implication that an aircraft OML satisfying a sonic boom ground noise level constraint at SOC will satisfy the same noise level constraint over the entire cruise segment, as long as a fixed AoA trajectory is flown.

Low-boom characteristics↗