Search NASA⌕ Search

SEARCH · Search NASA

Results for “coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Uniformity, performance, and durability of roll-to-roll-coated iridium oxide electrolyzer catalyst layers

This work investigates the use of roll-to-roll coating methods for the production of iridium oxide catalyst layers for proton exchange membrane water electrolyzers. Catalyst layers were produced using two coating methods: slot die and gravure. By varying the solids content of the catalyst ink and coating process variables loadings between 0.08 and 0.64 mg Ir cm −2 were prepared with relatively high spatial uniformity. However, at loadings below 0.2 mg Ir cm −2 microscopy reveals voids in the catalyst layer due to similar length scales of catalyst agglomerates and overall layer thickness. Electrochemical testing shows that these voids do not impact initial membrane electrode assembly performance but lead to increased performance losses after potential cycling compared to spray coated catalyst layers.

08 HYDROGEN↗
DOE OSTI2026

The mechanism of hydroxyapatite coatings degradation at high substrate temperatures

Physical vapor deposition methods used for hydroxyapatite (HA) coatings typically require elevated substrate temperatures and post-deposition annealing to induce crystallization. However, such thermal treatments can degrade both the mechanical integrity and bioactivity of the coating, particularly when substrate temperatures exceed 500 °C. The mechanisms underlying these phenomena remain insufficiently understood. In this study, HA thin films were deposited on silicon and Ti6Al4V substrates using pulsed laser deposition and were systematically characterized to elucidate these mechanisms. XPS and SIMS analyses revealed a temperature-dependent loss of OH − and PO 4 3− groups, an increased Ca/P ratio, and the formation of interfacial oxides, all of which contribute to weakened adhesion. To clarify the temperature-dependent decline in bioactivity, protein adsorption behavior was analyzed using a Kramers-type kinetic framework; the fitted desorption kinetics indicate that coatings deposited near ∼500 °C provide the most stable protein attachment, whereas higher temperatures accelerate desorption due to dehydroxylation and carbonate substitution. Together, these findings provide mechanistic insight into the thermal degradation of HA coatings and offer a framework for optimizing deposition parameters to preserve stoichiometry, adhesion, and bioactivity for long-term biomedical applications.

Kylychbekov, Salizhan [Univ. of Oxford (United Kin↗
DOE OSTI2024

Hopping and crawling DNA-coated colloids

Understanding the motion of particles with multivalent ligand-receptors is important for biomedical applications and material design. Yet, even among a single design, the prototypical DNA-coated colloids, seemingly similar micrometric particles hop or roll, depending on the study. We shed light on this problem by observing DNA-coated colloids diffusing near surfaces coated with complementary strands for a wide array of coating designs. We find colloids rapidly switch between 2 modes: They hop—with long and fast steps—and crawl—with short and slow steps. Both modes occur at all temperatures around the melting point and over various designs. The particles become increasingly subdiffusive as temperature decreases, in line with subsequent velocity steps becoming increasingly anticorrelated, corresponding to switchbacks in the trajectories. Overall, crawling (or hopping) phases are more predominant at low (or high) temperatures; crawling is also more efficient at low temperatures than hopping to cover large distances. We rationalize this behavior within a simple model: At lower temperatures, the number of bound strands increases, and detachment of all bonds is unlikely, hence, hopping is prevented and crawling favored. We thus reveal the mechanism behind a common design rule relying on increased strand density for long-range self-assembly: Dense strands on surfaces are required to enable crawling, possibly facilitating particle rearrangements.

Science & Technology - Other Topics↗
DOE OSTI2025

Outgassing measurements of bare and magnetite-coated low-carbon steel vacuum chambers

The outgassing properties of bare and magnetite-coated AISI 1020 low-carbon steel vacuum chambers were evaluated to establish material selection criteria for extreme high vacuum applications, namely, to explore the possibility of using these materials to build next-generation spin-polarized photoelectron guns. Water outgassing measurements using the throughput method revealed that the magnetite-coated chamber exhibited five times lower outgassing at room temperature prior to baking, but this advantage disappears after 80 °C baking. Hydrogen outgassing measurements demonstrated significant differences after intensive heat treatment: the bare low-carbon steel vacuum chamber achieved a specific outgassing rate of 9.6 × 10 −16 Torr L s −1 cm −2 after 400 °C/50 h bake plus additional heat treatment at lower temperatures, 25 times lower than the magnetite-coated low-carbon steel chamber. Residual gas analysis showed >99% hydrogen composition after heat treatment for both materials, with carbon species below detection limits for bare low-carbon steel versus 0.8% for magnetite-coated surfaces. These measurements indicate that properly conditioned bare low-carbon steel can achieve the <10 −12 Torr pressures required for next-generation spin-polarized photogun applications. In conclusion, the paper includes various analysis techniques intended to explain observed behaviors: isotherm analysis of pump-down plots, Arrhenius analysis of hydrogen outgassing rate data, and residual gas composition tracking.

Adsorption isotherm↗
DOE OSTI2024

Thermodynamics of Tritium Trapping by Point Defects in Intermetallic Al 12 (TM) 2.35 Aluminide Coating Phase

Density functional theory simulations have been carried out to investigate the potential for tritium trapping by metal vacancies in intermetallic Al 12 (TM) 2.35 phase (TM = Fe, Cr, and Ni) as function of temperature and tritium partial pressure. It was found that tritium could be favorably trapped by Fe and Ni vacancies and not favorably trapped by Al and Cr vacancies. However, due to the presence of partially occupied Al sites in bulk Al 12 (TM) 2.35 , leading to the approximate number of ~255 Al atoms in the unit cell, 86 sites were found energetically favorable to the creation of an Al vacancy. While adding a tritium atom in an Al vacancy is not energetically favorable, the tritiated defect still has a negative Gibbs free energy because the energy gain for creating an Al vacancy overcome the energy cost of adding the tritium species. Based on the calculated Gibbs free energy, the first tritiation of a metal vacancy, at conditions relevant to in-reactor operations, should be more favorable for Al, followed Fe, Ni, and Cr vacancies. By comparing the behavior of tritium in Al 12 (TM) 2.35 with previously studied Fe-Al coating phases (i.e., FeNiAl 5 , Fe 4 Al 13 , and Fe 2 Al 5.6 ), we found that there is a correlation between interstitial tritium solubility and the potential for vacancy trapping. The current trend suggests that if the insertion of an interstitial tritium cost more than 0.3 eV, then trapping by metal vacancies should be preferred. By combining the simulations results obtained to date, we noticed different trapping mechanisms of tritium in the Al coating. Tritium is mostly trapped by Fe and Ni vacancies in the outer Fe-Al coating phase Al 12 (TM) 2.35 while tritium should be preferentially trapped by Al and Fe vacancies for the inner Fe-Al coating phases (FeNiAl 5 , Fe 4 Al 13 , Fe 2 Al 5.6 ). Altogether, these studies show that tritium interacts differently with the various Fe-Al aluminide phases, they also suggest that tritium trapping and retention could be more efficient if metal defects are present and if the solubility of interstitial tritium in the different phases is low.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Nanoporous Carbon Coatings Direct Li Electrodeposition Morphology and Performance in Li Metal Anode Batteries

Li metal anodes could significantly improve battery energy density. However, Li generally electrodeposits in poorly controlled morphology, leading to safety and performance problems. One factor that controls Li anode performance and electrodeposition morphology is the nature of the electrolyte–current collector interface. Herein, we modify the Cu current collector interface by depositing precisely controlled nanoporous carbon (NPC) coatings using pulsed laser deposition to develop an understanding of how NPC coating density and thickness impact Li electrodeposition. We find that NPC density and thickness guide Li morphological evolution differently and dictate whether Li deposits at the NPC-Cu or NPC-electrolyte interface. NPC coatings generally lower overpotential for Li electrodeposition, though thicker NPC coatings limit kinetics when cycling at a high rate. Lower-density NPC enables the highest Coulombic efficiency (CE) during calendar aging tests, and higher-density NPC enables the highest CE during cycling tests.

25 ENERGY STORAGE↗
DOE OSTI2024

Calcined Polyethyleneimine-Coated Optical Fibers for Distributed pH Monitoring at High Pressures and Temperatures

In the oil and gas, CO2 sequestration, H2 subsurface storage, and geothermal energy sectors, subsurface pH measurements are critical for monitoring the geochemical conditions and estimating potential corrosion rates of wellbore systems. Real-time pH measurements in these conditions are vital for detecting and predicting corrosion deterioration of wellbore components that may jeopardize the safety and continued operation of wellbore systems. Previous tests using metal oxide-based coatings (TiO2) provided strong responses at elevated temperatures and moderate pressure stability but provided poor differentiation between acidic and alkaline solutions. Building off the pH responsiveness of the TiO2 surface and known pH sensitivity of amine-based polymers, a coating based on the secondary amine polymer polyethyleneimine (PEI) was developed. As the polymer itself is highly water soluble and easily removed by aqueous solutions, the sensor coating was treated with a high temperature (500 °C) calcination procedure in air to convert it into a more stable oxidized coating capable of withstanding hot aqueous solutions without dissolving while retaining linear pH sensitivity from pH values between 2 and 11. The sensor performance was measured using optical transmission measurements in solutions of various pHs and using optical backscatter reflectometry for distributed pH sensing demonstration in wellbore-relevant pressures (up to 1,000 psi) and temperatures (80 °C).

Shumski, Alexander↗
DOE OSTI2024

Effects of Strain Gauge Coatings on Water Intrusion in Submerged Composite Coupon Testing

Marine energy structures are typically made using composite materials and are repeatedly loaded by currents and waves. Submersion and repeated loading lead to two environmental effects: moisture intrusion and mechanical fatigue. To understand their combined effects, submerged fatigue testing can be used. Submerged fatigue testing often requires submerged instrumentation to validate component manufacturing methods and models. Strain measurements are critical for understanding marine energy component loads. One common method for measuring strain is by using foil strain gauges, but the durability of strain gauges in submerged fatigue conditions is not well-understood. To increase strain gauge durability and protection from contamination, delamination, and water intrusion, strain gauge coatings may be applied over strain gauges and wire connections. In this study, strain gauges were adhered to composite coupons, coated, and mechanically tested in a water tank. Cycles to composite failure, cycles to strain gauge failure (SGF), strains, and SGF modes were used to measure the effects of strain gauge coatings on composite fatigue life and strain gauge durability. The coatings did not have significant effects on composite fatigue life or strain gauge durability. The methods developed and measurements taken at the coupon scale in this study will be used to inform methods and designs for subsequent submerged subcomponent testing, full-scale testing, and standards development. The benefits of designing marine energy structures to informed standards and designs are decreased lifetime costs and increased reliability and energy production, ultimately leading to a sustainable and low-carbon energy system.

composite materials↗
DOE OSTI2025

High-resolution characterization of ceramic-metal interface of TiN coating on ferritic-steels for nuclear application

Advanced fuel cladding is critical for fast reactors, offering sufficient thermal conductivity, mechanical and dimensional stability and radiation tolerance of the cladding base material. Additionally, it must provide corrosion resistance and high temperature coolant compatibility on the cladding outer surface, as well as chemical stability on the cladding inner wall against fuel cladding chemical interaction (FCCI). TiN ceramic coating has been considered an effective diffusion barrier for inner and outer cladding-walls for enhanced performance. The TiN-metal interface microstructure and chemistry play a critical role in coating bond strength and integrity under harsh conditions. High-resolution transmission electron microscopy characterization of ceramic-metal interface at atomic resolution in unirradiated, irradiated and thermal cycled conditions were performed. The interface remained intact after irradiation up to 200 dpa or thermal cycling five times up to 550 °C. In conclusion, this work discusses the potential impact of these results on coating performance and design for advanced claddings.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

Copper–Carbon Nanotube Composites Enabled by Brush Coating for Advanced Conductors

There is a growing demand for advanced conductors with enhanced electrical properties to increase the energy efficiency in various applications. A promising strategy to achieve this involves the use of ultraconductive copper (UCC) composites that incorporate highly conductive carbon materials, such as carbon nanotubes (CNTs), into the copper matrix. In this study, we present a scalable brush coating technique to incorporate CNTs onto Cu substrates to produce Cu–CNT–Cu composites. The process involves brush coating the CNT solution on Cu tape substrates, followed by vacuum-assisted thermal removal of organic moieties (e.g., surfactant/polymer). This step ensures the creation of a uniformly distributed CNT network within the Cu matrix. By addition of a thin film Cu overlayer, the fabricated Cu–CNT–Cu composite architecture demonstrates similar electrical conductivity, increased current carrying capacity, and enhanced mechanical properties compared to pure Cu reference tapes. Finally, the performance characteristics of these UCC tapes along with the scalability of the brush coating approach hold great promise for the fabrication of advanced conductors for wide-ranging energy applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Multilayer film coating for laser ion source target for increase of low charge state production

The use of Laser Ion Source for accelerator facilities has the advantage to tune the characteristic of the produced beams by changing the laser parameters using the same primary target. The advantageous and innovative opportunity to manipulate the characteristic of charge state distributions by the use of composed target, may open new possibilities for the ion sources. In this experiment we characterize and study the plasma produced by the laser ablation of coated targets at constant laser parameters. The performed investigation has the double purpose to have a better understanding of penetration depth of laser in composed materials and understand how to tune the charge states by adding coating films. Finally, the obtained results showed that for particular thickness of coating, the low charge states were produced with higher yield than in the case of pure material.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Understanding Environmental Barrier Coating Lifetimes and Performance for Industrial Gas Turbines

Hydrogen or hydrogen blend fuels are expected to replace natural gas in land-based industrial gas turbines (IGTs) to support a greener power economy. Silicon carbide (SiC) base ceramic matrix composites (CMCs) are considered for replacement of Ni-based superalloys to facilitate future efficiency improvements. SiC CMCs require environmental barrier coatings (EBCs) to mitigate volatilization from high-temperature steam, thus making the EBC lifetime critical information for identifying CMC component lifetimes. Here, the goal of this project is to determine the maximum bond coating temperature underneath the EBC for achieving an IGT component lifetime goal of 25,000 h, which is far greater than current CMC component lifetime requirements for aeroturbine applications. To provide data for the lifetime model, laboratory testing used atmospheric plasma-sprayed rare-earth silicate EBCs on monolithic SiC substrates with an intermediate Si bond coating. Specimens exposed to 1-h thermal cycles in flowing air–steam environments and reaction kinetics were assessed from 700 °C to 1350 °C by measuring the thickness of the thermally grown silica scales. The silica growth and phase transformation appear critical in predicting EBC lifetime and several strategies have been explored to reduce the oxide growth rate and improve EBC durability at elevated temperatures. Advanced characterization using Raman spectroscopy has helped clarify this system.

08 HYDROGEN↗
DOE OSTI2024

Effects of Coatings on Water Intrusion and Strain Gauge Durability in Submerged Fatigue Conditions: Preprint

Marine energy structures are typically made using composite materials and are repeatedly loaded by currents and waves. Submersion and repeated loading lead to two environmental effects: moisture intrusion and mechanical fatigue. To understand the combined effects of moisture intrusion and mechanical fatigue on marine energy structures, submerged fatigue testing can be used. Submerged fatigue testing often requires submerged instrumentation to validate component manufacturing methods and models. Measuring strain is critical for understanding marine energy component loads. One common method for measuring strain is by using foil strain gauges, but the durability of strain gauges in submerged fatigue conditions was not well-understood. To increase strain gauge durability and protection from contamination, delamination, and water intrusion, strain gauge coatings may be applied over strain gauges and wire connections. In this study, strain gauges were adhered to composite coupons, coated, and mechanically tested in a water tank. Cycles to composite failure, cycles to strain gauge failure, strains, and strain gauge failure modes were used to measure the effects of strain gauge coatings on composite fatigue life and strain gauge durability. The methods developed and measurements taken at the coupon scale in this study will be used to inform methods and designs for subsequent submerged subcomponent testing, full-scale testing, and standards development. The benefits of designing marine energy structures to informed standards and designs are decreased lifetime costs and increased reliability and energy production, ultimately leading to a sustainable and low-carbon energy system.

composite fatigue testing↗
DOE OSTI2025

The Effect of Flow on CO2 Corrosion of Self-Healing Metallic Coatings

Internal corrosion is an issue that affects natural gas pipelines, a significant part of the United States energy infrastructure. Over time, this corrosion has worn away longstanding pipelines due to the original construction materials used for the lines and impurities in the gas and liquid streams flowing through them. The main impurities in natural gas are H2O, CO2, H2S, and O2. One of the leading causes of corrosion is the CO2 dissolved in water, giving rise to carbonic acid formation, which can further dissolve the steel pipe. The National Energy Technology Laboratory (NETL) has been studying different solutions to this problem. One potential answer is a self-healing sacrificial metallic coating applied by a novel cold spray technique. Previous studies at NETL have shown that the zinc-rich self-healing coating can withstand corrosion through passivation and create a barrier to the diffusion of corrosive species. This study explored the impact of flow on corrosion with this coating and carbon steel when exposed to a saturated CO2 environment by simulating the pipeline flow profile in a small-scale lab setting. The samples were evaluated using multiple electrochemical techniques that found corrosion rates and were backed up with surface analysis to conclude the behavior of the corrosion mechanisms.

CO2 corrosion↗
DOE OSTI2025

Fe Coated Optical Fiber for Distributed Corrosion Monitoring in Soil and Aqueous Environment

Natural gas pipeline corrosion represents a substantial cost and safety concern during normal operations. Effective monitoring of corrosion is important to detect and mitigate pipeline risks before corrosion-related catastrophic events happen. Here, we describe the use of Fe-coated optical fiber sensors (OFS) for distributed corrosion monitoring where Fe acts as a corrosion proxy. By using an optical backscatterring reflectometer (OBR), corrosion was monitored based on the increase in backscattered intensity amplitude of the light being passed as Fe undergoes corrosion. The Fe-coated OFSs were prepared with a film thickness between 25-225 nm by an electroless plating approach and corroded by a CO2-saturated acidic electrolyte. The corrosion rate was approximately 2.5 mm/yr for Fe with a film thickness of 30 nm and increased with film thickness. Backscattering-based corrosion rates were supported by visible light transmission measurements, which have been previously demonstrated. Additionally, a correlation between the intermittent transmission and residual Fe film thickness during corrosion of Fe was established. Corrosion was measurable out to > 100 m which is a significant improvement over our previous work showing corrosion sensing at < 10 m. The corrosion sensor was also tested in soil at >1 ft depth. Fe-coated OFS was loaded into a Draka cable which provides mechanical support during fiber deployment and installation into either acidified soil, top-soil, or sandy soil.

aqueous environment↗
DOE OSTI2025

Sequential Infiltration Synthesis of Bilayer Porous Alumina Nanostructures for Broad-Angle, Broadband Antireflective Coatings

Antireflective coatings (ARCs) are thin films engineered to reduce light reflections. Delivering broadband, wide-angle performance is essential for photovoltaics, imaging, and sensing, yet truly omnidirectional antireflection remains difficult due to angle-dependent optical paths and a narrow palette of suitable refractive indices. Here, in this study, we systematically investigate an emerging class of multilayer inorganic ARCs based on conformally coated nanoporous alumina templated by intrinsically microporous polymers (PIMs) and block copolymers (BCPs). We establish a design framework that maps thickness reflectance relationships to identify thickness pairs minimizing reflection across wavelength and incidence angle. We show that deliberately separating the local reflectance minima of the top and bottom layers in bilayer nanostructures broadens the antireflective bandwidth and angular range. We show that 235-nm single-side bilayer porous alumina nanostructures achieves under 2 % reflectance from 380–750 nm for incidence angles up to 45° with less than 0.6% reflectance for incidence angles under 20°. The approach is readily extensible to additional layers or materials with refractive indices tuned via templated nanoporosity and composition, enabling practical, etch-free ARC fabrication without HF or fluorinated precursors and advancing straightforward design of broadband, wide-angle (quasi-omnidirectional) ARCs for next-generation optical systems.

antireflective coatings↗
DOE OSTI2024

Programmable bionanocomposite coated fertilizers for prolonged controlled release of nitrogen

Controlled-release fertilizers (CRFs) present a promising solution for alleviating food and nutrient scarcity. However, their development has been mainly hindered by both rapid and unsynchronized nutrient release and unsustainable coating materials. In this study, we address this issue by developing a new coating layer for CRFs using a programmable biopolyurethane nanocomposite. This nanocomposite is prepared from diphenylmethane diisocyanate (MDI)-functionalized bentonite nanoclay (BNT-MDI) and a biopolyol from biomass waste. The results show that the BNT-MDI-doped CRFs (BCRFs) exhibit an impressive nitrogen (N)-release longevity of approximately 120 days at a 4 wt% coating ratio, surpassing previous CRF formulations. In a 30-day snap bean cultivation study, BCRF significantly improved root length (1000%), leaf length (257%), leaf width (400%), and plant height (1400%) compared to the control. The superior performance of BCRF is attributed to the PU-nanoclay biocomposite film, with full nano-exfoliation, controllable porosity, and high crosslinking density. Furthermore, we introduce a new dynamic release mechanism and establish a quantitative relationship between the nanostructure, property, and release performance of BCRF by combining the multiplicative and diffusion models for porous materials. Finally, this study provides a theoretical framework and a straightforward methodology for designing programmable nanocomposite structures for future biobased CRFs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Development of copper thiolate organometallic compound as thermal sensitive coating for energy storage system safety

Safety and reliability are primary concerns for the deployment of lithium-ion batteries, especially in electric vehicles (EV) and larger-scale energy storage systems (ESS). Current technology in battery management systems (BMS) includes cell voltage monitoring and positioning temperature sensors in selected locations. For a system with hundreds to thousands of individual batteries, single-point temperature monitoring is inadequate to detect hot spots and cell overheating, which could lead to thermal runaway. Here, we have developed a temperature-sensitive copper-thiol compound that can be directly coated onto battery pouch foils to enable early detection of thermal runaway. Upon reaching specific temperatures, this compound releases a sulfur-containing detectable gas, which can be identified using chemically specific gas sensors to trigger an early warning signal. Such a signal propagate through air offers broad signal coverage and enables a more comprehensive approach to large-area temperature monitoring. The Cu-ethanethiol coating is designed to release volatile gases when the substrate surface temperature exceeds 70 °C, with continuous outgassing as the temperature increases. The compound is composed of Cu, S, Cl, hydrocarbons and trace amounts of oxygen. Upon heating, the oxidation state of Cu(I) transitions to Cu (II), accompanied by gas release. Thermogravimetric analysis coupled with mass spectrometry correlated well with the onset of gas release temperature and emission of sulfur-containing volatile gases. Additionally, an acrylic overcoat is applied to enhance the adhesion of the thermally sensitive compound film to the battery pouch foil. This coating is expected to offer an additional safety layer for ESS, alerting possible thermal runaway events before a failure occurs, thereby allowing sufficient time to implement a mitigation plan.

Early warning systems↗