Search NASA⌕ Search

SEARCH · Search NASA

Results for “compaction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

High Effectiveness, Compact, High Pressure and Low Cost Recuperator for Super-Critical CO2 Power Cycles, Paper Presented at The Fifth International Symposium – Super-Critical CO2 Power Cycles, San Antonio, Texas, March 28-31, 2016, by Dr. John Kelly, President, Altex Technologies Corporation

Closed Brayton super-critical CO2 power cycles are well suited to waste heat bottoming cycles, due to their increased efficiency and compactness, relative to Rankine steam bottoming cycles. Since waste heat applications would be retrofits, the power system compactness is important. To achieve high efficiency, these power cycles require high pressure recuperative type heat exchangers, of substantial heat duty. Current Printed Circuit Heat Exchangers (PCHE), originally developed for high pressure gas and oil applications, can be used as recuperators, but costs are higher than desired. Altex is developing a purpose-built high pressure and effectiveness recuperator to provide the reliability, compactness, performance and pressure capability of current recuperators, but at a reduced cost. The High Effectiveness Low Cost (HELC) recuperative heat exchanger design yields volume and weight metrics of .0024 m3/UA and 10.2 kg/UA, which are 4% and 77.3% below recuperator target metrics, respectively. A 50 kW test article was designed and fabricated. Performance tests on water and oil showed that the HELC design model could predict heat transfer, to within 10% of the measured value. This model was then used to project HELC performance, when operating on supercritical CO2. Besides performance tests, the test article was hydrostatically tested, for integrity at up to 4,000 psi pressure. At these conditions, some distortion of channels was encountered. To mitigate distortion, the inserts were redesigned and these results were used to project the cost of 500 kW and 5,083 kW HELC units. The cost metric for the 5,083 kW unit was determined to be $1,349/UA, which is 10% lower than the recuperator desired cost metric desired target of $1,500/UA. In addition, the 5,083 kW unit HELC cost of $61.09/kW is 33.6% lower than the $92/kW estimated cost for a PCHE. Hydrostatic pressure tests, at up to 4,000psi, showed that the unit did not leak. However, channels were distorted at this pressure differential. Design updates to minimize stress concentrations and distortion were prepared and analyzed, to show that distortion could be controlled, but to date tests have not been run to prove the design. Project results show the potential of the HELC approach, but more work is required to confirm this potential, at the larger scales of interest.

14 SOLAR ENERGY↗
DOE OSTI2020

Techno-Economic Analysis for GTI's Compact Hydrogen Generator

A technoeconomic analysis of the compact hydrogen generator compared to a traditional steam methane reformer (SMR) was performed for both processes with and without carbon capture. The project goal for the technoeconomic analysis was to demonstrate a minimum of 20% lower CAPEX and 15% lower levelized cost of hydrogen compared to SMR with and without carbon capture. GTI obtained baseline capital and costs for the SMR with and without and methodology to calculate the levelized cost of hydrogen from an IEAGHG Technical Report: 2017-02 Techno-Economic Evaluation of SMR Based Standalone (Merchant) Hydrogen Plant with CCS. This methodology was then applied to GTI’s compact hydrogen generator using direct material costs previously obtained from a reputable engineering procurement and construction company, CB&I Howe-Baker. The analysis was performed for plants producing 90MMSCFD (million standard cubic feed per day) of hydrogen. Direct material costs were converted to total installed costs and total capital requirements using the same multiplying factors for both processes. We have found that the direct materials cost of the compact hydrogen generator is less than half the direct materials cost required for SMR without capture, and about one quarter the direct materials cost of SMR with carbon capture. This low materials cost translates into a significant CAPEX savings and lower levelized cost of hydrogen that exceed the goals of the techno-economic assessment. We have found that the CHG has a 43% lower installed cost and capital requirement compared to SMR without capture, that results in a levelized cost of hydrogen that is 19% lower than SMR. When 90% CO2 capture is added to the plants, the advantages is even better. The CHG has a 51% lower installed and capital requirement compared to SMR with capture, resulting in a 28% lower levelized cost of hydrogen. A sensitivity analysis was performed and showed natural gas feedstock cost and discount rate to be the main contributors to hydrogen price sensitivity. Given these significant cost advantages, GTI is encouraged to continue to develop the technology and market the economic advantages as well as the efficiency gains and ability to inherently capture CO2.

08 HYDROGEN↗
DOE OSTI2020

DEM and MELT: A Modular and Compact In-Can Melting Technology Dedicated to D and D and Remediation Waste - 20033

The DEM and MELT In-Can vitrification process is designed to process intermediate and high level waste coming for D and D and remediation operations. It is developed to treat liquid and solid waste, to produce a small amount of secondary waste and to minimize investment and operating costs. This In-Can vitrification process is also developed with a compact and modular design and can be adapted regarding nuclear operators' needs and requirements. Furthermore, this robust and simple process is flexible enough to accommodate most uncertainties on waste composition. The DEM and MELT process is developed through the French consortium coordinated by CEA which gathers Orano, ECM technologies and Andra. In the frame of this project, Orano has designed a compact and modular layout of the process allowing an efficient in situ implementation, close to the waste to be treated. This paper presents the compact and modular design of the DEM and MELT process and the way it can be used for a short duration, as a decommissioning tool aimed to be dismantled just after the treatment operation. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Dynamical Heating from Dark Compact Objects and Axion Minihalos: Implications for the 21-cm Signal

The temperature of baryons at the end of the cosmic dark ages can be inferred from observations of the 21-cm hyperfine transition in neutral hydrogen. Any energy injection from the dark sector can therefore be detected through these measurements. Dark compact objects and dark-matter substructures can modify the baryon temperature by transferring heat via dynamical friction. In this work, we evaluate the prospects for detecting dynamical friction-induced heating from dark compact objects with a mass in the range $10^2 M_{\odot}$ to $10^5 M_{\odot}$, as well as from axion minihalos, using upcoming 21-cm experiments. We find that both the 21-cm global signal and power-spectrum measurements will be sensitive to dark compact objects that constitute about 10% of the dark matter, and will substantially improve our sensitivity to axion-like particles with masses in the range $10^{-18}$ eV to $10^{-9}$ eV.

Bhalla, Badal [Oklahoma U.] (ORCID:000000030488664↗
DOE OSTI2026

A Chemodynamical Census of the Milky Way's Ultra-Faint Compact Satellites. I. A First Population-Level Look at the Internal Kinematics and Metallicities of 19 Extremely-Low-Mass Halo Stellar Systems

Deep, wide-area photometric surveys have uncovered a population of compact ($r_{1/2} \approx$ 1-15 pc), extremely-low-mass ($M_* \approx$ 20-4000 $M_{\odot}$) stellar systems in the Milky Way halo that are smaller in size than known ultra-faint dwarf galaxies (UFDs) and substantially fainter than most classical globular clusters (GCs). Very little is known about the nature and origins of this population of "Ultra-Faint Compact Satellites" (UFCSs) owing to a dearth of spectroscopic measurements. Here, we present the first spectroscopic census of these compact systems based on Magellan/IMACS and Keck/DEIMOS observations of 19 individual UFCSs, representing $\sim$2/3 of the known population. We securely measure mean radial velocities for all 19 systems, velocity dispersions for 15 (predominantly upper limits), metallicities for 17, metallicity dispersions for 8, and $\textit{Gaia}$-based mean proper motions for 18. This large new spectroscopic sample provides the first insights into population-level trends for these extreme satellites. We demonstrate that: (1) the UFCSs are kinematically colder, on average, than the UFDs, disfavoring very dense dark matter halos in most cases, (2) the UFCS population is chemically diverse, spanning a factor of $\sim$300 in mean iron abundance ($\rm -3.3 \lesssim [Fe/H] \lesssim -0.8$), with multiple systems falling beneath the "metallicity floor" proposed for GCs, and (3) while some higher-metallicity and/or younger UFCSs are clearly star clusters, the dynamical and/or chemical evidence allows the possibility that up to $\sim$50% of the UFCSs in our sample (9 of 19) may represent the smallest and least-massive galaxies yet discovered.

Cerny, William [Yale U.] (ORCID:0000000316977062)↗
DOE OSTI2026

Discovery and Spectroscopic Characterization of a Distant, Compact Milky Way Satellite in Gemini

We present the discovery of a compact Milky Way satellite in the constellation of Gemini. This system was discovered by cross-matching detections from two independent search algorithms applied to Blanco/DECam data from the third data release of the DECam Local Volume Exploration survey (DELVE DR3), and confirmed with deeper imaging from Gemini/GMOS-N. Based on these data, we determine that the system is an ultra-faint ($M_V = -2.1^{+0.4}_{-0.6}$), compact ($r_{1/2} = 8.6^{+1.4}_{-1.2}$ pc) system located at a heliocentric distance of $120^{+7}_{-6}$ kpc. These physical properties place the system in the regime of ambiguous, ultra-faint compact Milky Way halo satellites that cannot be confidently classified as dwarf galaxies or star clusters from morphology alone; we therefore name the system DELVE 8/Gemini I. From medium-resolution Keck/DEIMOS spectroscopy, we securely identify four members including two blue horizontal branch stars, confirming the system as a bound satellite moving at a mean radial velocity of $v_{\rm hel} = -82.7^{+3.7}_{-3.9} {\rm km\,s}^{-1}$. We also use these spectra to place an upper limit of $\rm [Fe/H] \lesssim -2.5$ on the metallicity of DELVE 8/Gemini I's brightest star, supporting the classification of the system as either an ancient star cluster or ultra-faint dwarf galaxy. The discovery of faint, distant systems similar to DELVE 8/Gemini I is expected to become more common with upcoming surveys.

Overdeck, K. [Chicago U., Astron. Astrophys. Ctr.;↗
DOE OSTI2025

Fuel performance analysis of fully-resolved TRISO compact

The TRi-structural ISOtropic (TRISO) fuel multilayered coating structure offers multiple barriers to fission product release, enhancing safety and performance. The heterogeneous nature of TRISO fuel compacts, comprising thousands of randomly distributed coated fuel particles embedded in a graphite matrix, creates intricate stress fields and thermal gradients that cannot be accurately modeled using simplified one-dimensional or homogenized approaches. Consequently, three-dimensional modeling enables the prediction of fuel compact dimensional changes, internal pressure buildup, and fission product transport pathways under diverse irradiation and thermal conditions. This capability facilitates detailed analysis of particle-to-particle interactions, matrix cracking mechanisms, and the statistical distribution of coating failures, which directly impact fuel performance and safety margins. This capability is particularly critical for advanced reactors, such as high-temperature gas-cooled reactors and other Generation IV reactor designs where TRISO fuel operates at elevated temperatures and burn-up levels. This work introduces a novel method to generate an optimized packing of TRISO compacts and a complete 3D mesh with random distribution of TRISO particles, which are discretized into each coating component layer.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Simulation of axial tensile well deformation during reservoir compaction in offshore unconsolidated methane hydrate-bearing formation

Sand production encountered in the 2013 offshore field gas production tests at the Nankai Trough, Japan, could be attributed to well failure during reservoir compaction. In this study, well integrity under various reservoir compaction patterns for the Nankai Trough case is examined using a well-formation finite element model. Here, the modelling details include the inclusion of a cement sheath as well as the modelling of construction processes (such as cement shrinkage). Well elongation in the overburden layer becomes significant when the reservoir subsidence is localized near the wellbore under large depressurization. Results show that the maximum plastic deviatoric strain level in the cement could reach 0.7% when the maximum reservoir subsidence reaches 0.85 m and cement shrinkage is limited. When cement shrinkage rises to 0.75%, the maximum plastic deviatoric strain increases to 2.4% as the cement accumulates additional plastic strain during shrinkage due to its deformation being constrained by the casing. In order to prevent the cement from failure, it might be effective to hold the pressure drawdown at a low level (e.g., several MPa) until the hydrate dissociation front advances to a certain radius from the well (e.g., a couple of tens of metres).

58 GEOSCIENCES↗
DOE OSTI2023

Heavy-element production in a compact object merger observed by JWST

The mergers of binary compact objects such as neutron stars and black holes are of central interest to several areas of astrophysics, including as the progenitors of gamma-ray bursts (GRBs), sources of high-frequency gravitational waves (GWs) and likely production sites for heavy-element nucleosynthesis by means of rapid neutron capture (the r -process). Here we present observations of the exceptionally bright GRB 230307A. We show that GRB 230307A belongs to the class of long-duration GRBs associated with compact object mergers and contains a kilonova similar to AT2017gfo, associated with the GW merger GW170817. We obtained James Webb Space Telescope (JWST) mid-infrared imaging and spectroscopy 29 and 61 days after the burst. The spectroscopy shows an emission line at 2.15 microns, which we interpret as tellurium (atomic mass A = 130) and a very red source, emitting most of its light in the mid-infrared owing to the production of lanthanides. These observations demonstrate that nucleosynthesis in GRBs can create r -process elements across a broad atomic mass range and play a central role in heavy-element nucleosynthesis across the Universe.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Cost Drivers for a Tokamak-Based Compact Pilot Plant

A comprehensive systems code that includes a range of physics and engineering considerations along with a simplified costing model has been utilized to evaluate the primary cost drivers for a compact tokamak pilot plant. The systems code has been benchmarked against several tokamak reactor designs and is utilized with sophisticated optimization algorithms to develop optimal solutions for a set of user-specified assumptions and design constraints. Here, in contrast to previous models that have focused on the cost of electricity as the key cost metric, this study uses the estimated capital cost of the facility. The analysis suggests that a pilot plant with the following features may offer potential for a cost-attractive pilot plant: A ~ 3, H 98y2 > 1.5, P net = 200 MW, 𝜏 𝑝⁢𝑢⁢𝑙⁢𝑠⁢𝑒 ~ 1 to 2 h utilizing rare-earth barium copper oxide (REBCO) magnet technology and a plug-bucked central solenoid/toroidal field (CS/TF) magnet support structure. While REBCO magnets offer some advantages relative to Nb 3 Sn magnets in all cases, the most gain is obtained when combined with the plug-bucked CS/TF bucking solution. Pulsed operation reduces capital cost requirements relative to steady-state operation, especially at low confinement. Cost sensitivity studies indicate that there are significant cost uncertainties associated with the achievable confinement quality, tritium breeding capability, attainable thermal efficiency, and achievable neutron wall loading, suggesting that these areas are the most critical areas in reducing the cost risk for a compact tokamak pilot plant. Further cost sensitivity studies indicate that the estimated cost is most sensitive to the underlying cost of the magnetic coils, providing further impetus to better establish cost-effective means for producing fusion magnets.

Compact pilot plant↗
DOE OSTI2021

The advanced tokamak path to a compact net electric fusion pilot plant

Abstract Physics-based simulations project a compact net electric fusion pilot plant with a nuclear testing mission is possible at modest scale based on the advanced tokamak concept, and identify key parameters for its optimization. These utilize a new integrated 1.5D core-edge approach for whole device modeling to predict performance by self-consistently applying transport, pedestal and current drive models to converge fully non-inductive stationary solutions, predicting profiles and energy confinement for a given density. This physics-based approach leads to new insights and understanding of reactor optimization. In particular, the levering role of high plasma density is identified, which raises fusion performance and self-driven ‘bootstrap currents’, to reduce current drive demands and enable high pressure with net electricity at a compact scale. Solutions at 6–7 T, ∼4 m radius and 200 MW net electricity are identified with margins and trade-offs possible between parameters. Current drive comes from neutral beam and ultra-high harmonic (helicon) fast wave, though other advanced approaches are not ruled out. The resulting low recirculating power in a double null configuration leads to a divertor heat flux challenge that is comparable to ITER, though reactor solutions may require more dissipation. Strong H-mode access (x2 margin over L–H transition scalings) and ITER-like heat fluxes are maintained with ∼20%–60% core radiation, though effects on confinement need further analysis. Neutron wall loadings appear tolerable. The approach would benefit from high temperature superconductors, as higher fields would increase performance margins while potential for demountability may facilitate nuclear testing. However, solutions are possible with conventional superconductors. An advanced load sharing and reactive bucking approach in the device centerpost region provides improved mechanical stress handling. The prospect of an affordable test device which could close the loop on net-electric production and conduct essential nuclear materials and breeding research is compelling, motivating research to validate the techniques and models employed here.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Achievement of ion temperatures in excess of 100 million degrees Kelvin in the compact high-field spherical tokamak ST40

Abstract Ion temperatures of over 100 million degrees Kelvin (8.6 keV) have been produced in the ST40 compact high-field spherical tokamak (ST). Ion temperatures in excess of 5 keV have not previously been reached in any ST and have only been obtained in much larger devices with substantially more plasma heating power. The corresponding fusion triple product is calculated to be n i 0 T i 0 τ E ≈ 6 ± 2 × 10 18 m − 3 keVs . These results demonstrate for the first time that ion temperatures relevant for commercial magnetic confinement fusion can be obtained in a compact high-field ST and bode well for fusion power plants based on the high-field ST.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

HTS Cable Conductor for Compact Fusion Tokamak Solenoids

Significant progress has been made recently in the US fusion community to develop a strategic plan to enable engineering design and construction of a fusion pilot plant (FPP). Princeton Plasma Physics Laboratory (PPPL) is working on developing high current density HTS conductors for next fusion experiments. Partnering with the US industry, we are evaluating feasibility and affordability of Conductor on Round Core (CORC ® ) developed by Advanced Conductor Technologies (ACT) for the next compact fusion tokamak facility. High current density achieved by a CORC ® cable based on a four-layer model coil recently tested at National High Magnetic Field Laboratory (NHMFL) motivated its consideration for low cost, reduced size fusion magnet application. This is of interest to PPPL because of its scalability to tokamak central solenoid (CS) coils in terms of required flux swings for plasma startup operations. Furthermore, partnering with ACT, we designed and built a two-layer model coil solenoid directly wound with CORC to demonstrate its applicability for compact solenoids such as that used in the national spherical torus experiment (NSTX), NSTX-upgrade (NSTX-U) and the US sustained high-power density test facility (SHPD). The ~160 mm diameter solenoid wound by a two-layer CORC is being tested in early 2022 under electromagnetic cyclic loading at NHMFL in a unique 160 mm bore, 14 T background field magnet facility.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

On the bulk compaction of brittle granular materials, Part III: Brittle‐to‐ductile transition and yield strength

A new and simple method is presented that enables the estimation of the yield strength (σ y ) of brittle materials (e.g., ceramics, glasses). It results from the combination of sufficiently high-stress compaction of their granular form, postmortem analysis of the crushed particles to identify the critical particle size corresponding to their brittle-to-ductile transition, and the use of a developed and simple analytical expression. Here, this method was an outcome from Part I of this three-paper series. To execute it, a granular brittle material is compacted to a sufficiently high stress, whereby the acting comminution produces both a fraction of particles having a sufficiently small size formed by ductile or plastic-like deformation and a remaining fraction of larger particles formed from brittle fracture. Postmortem microscopy is then used to identify the smallest particle size whose morphology indicates it formed from brittle fracture (d B2D ). The brittle material's σ y can then be estimated using a combination of the d B2D , Kendall's and Griffith's theories, a priori knowledge of the material's fracture toughness (K Ic ), and a fracture mechanics shape factor constant (Y) using σ y = √((32 π K Ic 2 )/(3 Y 2 d B2D )). The method's development and its use to estimate σ y for several vitreous silicates, α-quartzes, and NaCl are provided.

Compaction↗
DOE OSTI2025

Vitreous silica formation within shear bands in a dynamically compacted granular crystalline α‐quartz

A shear band is a heterogeneous, narrow seam within a solid material whose formation is caused by intense localized shearing when a sufficiently large amount of deformation occurs. If that deformation occurs at a sufficiently rapid rate, with operative friction, then co‐located ephemeral heating will occur in the shear band. In this study, shear bands were produced from dynamic shear‐induced compaction of a granular form of crystalline α‐quartz (SiO 2 ). The produced shear bands were approximately 25‐µm thick and were examined with scanning electron microscopy/electron backscatter diffraction, transmission electron microscopy, Raman spectroscopy, and nanoindentation. Further, they were found to contain a mixture of vitreous silica and small‐sized crystallites. This finding is significant because the presence of the vitreous silica within the shear band is a postmortem indicator that the localized temperature had reached or exceeded the melting temperature (∼1723°C) of crystalline SiO 2 during the rapid shear and compaction and then sufficiently rapid cooling quenched in that vitreous state.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Using the Carbon Capture Simulation Initiative (CCSI) Tool to Design the Experiments in the Parametric Campaign of a Novel Compact Absorber for Carbon Capture

Gas absorption towers with structured packing and solvent have been used for Carbon Dioxide (CO 2 ) Capture for about many decades. To overcome process limitations and practical disadvantages for CO 2 capture from the stationary emitter (e.g. NG and coal power plant), many new designs have been proposed and explored at the various scales in the last decade with aim of either low energy penalty or low capital cost. To reduce the size of the absorption tower and hence the total cost of CO 2 capture, the University of Kentucky Center for Applied Energy Research Center (UK CAER) has designed and built a novel CO 2 capture absorption tower or Compact Absorber, integrated into an existing large-bench scale CO 2 capture unit. The Compact Absorber has three sections. The top of the column is a fogging section where the solvent is sprayed through a nozzle producing droplets flowing downward in a co-current fashion with the flue gas. The center of the column is a frothing section where the solvent and flue gas flow through regenerative frothing screens designed by Industrial Climate Solutions, Inc. The bottom of the column is a typical structured packing section were the flue gas and solvent flow in a counter-current fashion. The parametric campaign will be conducted in order to optimize the operating parameters for CO 2 capture including liquid/gas ratio, lean loading, and temperature, liquid residence time. A simulated flue gas with 14% CO 2 will be used along with a UK CAER developed proprietary solvent. The 100-hour parametric campaign is designed using a statistical approach of the Sequential Design of Experiments (sDOE). sDOE is one of the CCSI tools that provides an adaptive statistical approach for designing future experiments based on the results of previous experiments. Application of a typical DOE provides the user with the minimum number of experiments required to get the same data, but sDOE allows the user to make an informed choice of experiments based on the results of previous experiments. The complete absorption column has been constructed and has been partially commissioned. Initial data has been collected by operating using the fogging section and the frothing section. The fogging section produces solvent droplets of about 100 μm sauter mean diameter and as small as 25 μm using a hydraulic nozzle by BETE. The frothing section produces bubbles of about 5mm with high mixing of solvent promoting the higher mass transfer from gas to liquid. The absorber reaches the capture efficiency of about 50% with only two sections in operation. Based on the current results, it can be deduced that increasing the solvent feed temperature and including the packed section for absorption the capture efficiency will increase further. Initial data will be collected using all three sections of the absorber and will be used for sDOE. Non-Uniform Space Filling model of sDOE will be used to prioritize the input conditions resulting into maximum capture efficiency. sDOE is performed using the platform called Framework Optimization, Quantification of Uncertainty, and Surrogates (FOQUS). The method and results demonstrating the progress of the parametric campaign from the initial set of experiments to the final stage of obtaining optimized parameters using sDOE tool will be presented in detail.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2023

Simulation of Reverse Osmosis Membrane Compaction Using Material Point Method (MPM)

Access to fresh drinking water in the future requires effective management of industrial wastewater and water purification from available resources. In this study, we present the simulation methodology and the analysis of a Reverse Osmosis (RO) membrane under various pressure conditions using the Material Point Method (MPM). In contrast to other numerical methods, MPM solves the continuum governing equations on material points in a Lagrangian framework. The method does not require a grid connecting the material points hence making it suitable to simulate large deformations during membrane compaction. The time integration is carried out using the explicit Euler method, while the spatial discretization is performed using linear or cubic-spline shape functions. A series of planar images containing detailed pore structures obtained from X-ray tomography experiments is converted to a three-dimensional collection of material points to simulate the membrane. Compressive loads are applied to the top layer of the membrane to simulate the experiments. The membrane deformation and pore size distribution before and after load application are reported and compared with the experimental measurements. The presentation discusses the numerical methods used, the performance of the solver on high-performance computing machines, and the results of membrane compaction in detail.

ENGINEERING,MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Simulation of Reverse Osmosis Membrane Compaction Using Material Point Method

Reverse Osmosis (RO) is a promising technology to address the impending water-crisis in the upcoming decades. RO at high salinities and high pressures is challenging due to membrane compaction that changes its porosity and permeability. In this study, we present a simulation methodology for membrane structural mechanics to understand pore size distribution and permeability variations under high pressure. We use the material point method (MPM), that solves the solid mechanics equations in a Lagrangian framework. MPM provides many features that make it well-suited for simulating mesoporous membranes. The Lagrangian framework allows for large deformations, easy integration of constitutive models and direct import of complex geometries as particles. The spatial discretization in our MPM solver is achieved using linear or cubic-spline shape functions while the time integration is carried out using the explicit Euler method. A series of images containing detailed pore structures obtained from X-ray tomography is first converted to a collection of material points. Compressive loads are applied to the top layer of the membrane to simulate the application of pressure. The membrane deformation and pore size distribution before and after load application are reported and compared with the experimental measurements. The presentation discusses the numerical methods used, the performance of the solver on high-performance computing machines, and the results of membrane compact in detail.

compaction↗