Results for “consumer choice” — Page 7

NASA NTRSDate not supplied

Appetite and Food Intake During 11 Days of Mild Hypobaric Hypoxia

Introduction Reduced food consumption and loss of body mass and muscle mass have been observed during spaceflight. Hypoxic conditions that astronauts may encounter on exploration missions may further implicate satiety signals and dietary intake. Appetite, food intake, and satiety hormones were investigated under the conditions of mild hypoxia and high energy output during simulated extravehicular activity (EVA) to determine the adequacy of a mission relevant space food system to support energy balance and body composition. Methods Foods realistic to early Artemis missions was packed by meal for each subject for the 11-day test based on estimated energy requirements (EER) and estimated EVA caloric requirements. No hot water or food warmer was provided and only room temperature water was available to rehydrate food and beverages in-mission, mimicking plans for early Artemis missions. Measures included food records (pre-mission, in-mission); fasted body weight (pre-mission, in-mission); Dual-energy X-ray absorptiometry (DXA) (pre-mission, post-mission); subjective ratings and feedback of food acceptability, mealtime and meal preparation sufficiency, appetite, and nausea (in-mission); and circulating ghrelin and leptin concentration in fasted blood samples (pre-mission, in-mission: pre-post EVA). Results All subjects consumed fewer calories in-mission than predicted. On average, subjects consumed 341 calories less on EVA days compared to non-EVA days in-mission (p=0.0511). The total weight loss estimate from daily weight measurements (-1.1 kg, p=0.0028) is consistent with underconsumption and supported by DXA measurements (-1.3 kg total body mass, p=0.0123 and -1.6 kg fat mass, p=0.0016). In general, most foods that were consumed were given acceptable scores, but subject comments indicated that the most acceptable foods were those not intended to be heated. Comments also indicated that subjects found their favorite foods early in the mission and avoided the foods that they did not like throughout the mission. Habitability scores indicated that overall aspects of the food system were considered borderline or unacceptable over the length of this mission. Foods that caused gas were avoided pre-EVA to prevent discomfort during pressure changes. Average fruit and vegetable intake decreased during the mission, dropping from 4.8 servings/d pre-mission to 3.4 servings/d on non-EVA days in-mission (p=0.0872) and 2.3 servings on EVA days (p=0.0020). Fasting ghrelin concentrations tended to be lower pre-EVA and on non-EVA days when exposed to mild hypoxia compared to normoxic conditions pre-mission and post-EVA (p=0.0136). Fasting levels of leptin did not change. Discussion Food intake was reduced in-mission, resulting in a caloric deficit and weight loss for most subjects. Crew food and appetite ratings and comments indicated this was due to a combination of food choices, lack of preference, lack of preparation capability, lack of time for meal preparation, consumption, and cleanup, and physiological challenges with the changing pressure. The regulation of appetite stimulating hormone ghrelin, but not the appetite suppressor leptin, appeared to be sensitive to hypoxic conditions. Conclusions Food preparation capabilities and time for meals are important for promoting adequate food intake. Reduced appetite and food intake during missions may further be aggravated under hypoxic conditions through the suppression of ghrelin. Lack of time for meals on EVA days, and avoidance of potential gas-causing foods (e.g., health promoting fruits and vegetables) prior to EVAs, demonstrate the importance of scheduling ample recovery time between EVA days.

Grace L Douglas↗

NASA NTRS2023

Appetite and Food Intake During 11 Days of Mild Hypobaric Hypoxia

Introduction Reduced food consumption and loss of body mass and muscle mass have been observed during spaceflight. Hypoxic conditions that astronauts may encounter on exploration missions may further implicate satiety signals and dietary intake. Appetite, food intake, and satiety hormones were investigated under the conditions of mild hypoxia and high energy output during simulated extravehicular activity (EVA) to determine the adequacy of a mission relevant space food system to support energy balance and body composition. Methods Foods realistic to early Artemis missions was packed by meal for each subject for the 11-day test based on estimated energy requirements (EER) and estimated EVA caloric requirements. No hot water or food warmer was provided and only room temperature water was available to rehydrate food and beverages in-mission, mimicking plans for early Artemis missions. Measures included food records (pre-mission, in-mission); fasted body weight (pre-mission, in-mission); Dual-energy X-ray absorptiometry (DXA) (pre-mission, post-mission); subjective ratings and feedback of food acceptability, mealtime and meal preparation sufficiency, appetite, and nausea (in-mission); and circulating ghrelin and leptin concentration in fasted blood samples (pre-mission, in-mission: pre-post EVA). Results All subjects consumed fewer calories in-mission than predicted. On average, subjects consumed 341 calories less on EVA days compared to non-EVA days in-mission (p=0.0511). The total weight loss estimate from daily weight measurements (-1.1 kg, p=0.0028) is consistent with underconsumption and supported by DXA measurements (-1.3 kg total body mass, p=0.0123 and -1.6 kg fat mass, p=0.0016). In general, most foods that were consumed were given acceptable scores, but subject comments indicated that the most acceptable foods were those not intended to be heated. Comments also indicated that subjects found their favorite foods early in the mission and avoided the foods that they did not like throughout the mission. Habitability scores indicated that overall aspects of the food system were considered borderline or unacceptable over the length of this mission. Foods that caused gas were avoided pre-EVA to prevent discomfort during pressure changes. Average fruit and vegetable intake decreased during the mission, dropping from 4.8 servings/d pre-mission to 3.4 servings/d on non-EVA days in-mission (p=0.0872) and 2.3 servings on EVA days (p=0.0020). Fasting ghrelin concentrations tended to be lower pre-EVA and on non-EVA days when exposed to mild hypoxia compared to normoxic conditions pre-mission and post-EVA (p=0.0136). Fasting levels of leptin did not change. Discussion Food intake was reduced in-mission, resulting in a caloric deficit and weight loss for most subjects. Crew food and appetite ratings and comments indicated this was due to a combination of food choices, lack of preference, lack of preparation capability, lack of time for meal preparation, consumption, and cleanup, and physiological challenges with the changing pressure. The regulation of appetite stimulating hormone ghrelin, but not the appetite suppressor leptin, appeared to be sensitive to hypoxic conditions. Conclusions Food preparation capabilities and time for meals are important for promoting adequate food intake. Reduced appetite and food intake during missions may further be aggravated under hypoxic conditions through the suppression of ghrelin. Lack of time for meals on EVA days, and avoidance of potential gas-causing foods (e.g., health promoting fruits and vegetables) prior to EVAs, demonstrate the importance of scheduling ample recovery time between EVA days.

Lichar Dillon↗

NASA NTRS2013

SIM_EXPLORE: Software for Directed Exploration of Complex Systems

Physics-based numerical simulation codes are widely used in science and engineering to model complex systems that would be infeasible to study otherwise. While such codes may provide the highest- fidelity representation of system behavior, they are often so slow to run that insight into the system is limited. Trying to understand the effects of inputs on outputs by conducting an exhaustive grid-based sweep over the input parameter space is simply too time-consuming. An alternative approach called "directed exploration" has been developed to harvest information from numerical simulators more efficiently. The basic idea is to employ active learning and supervised machine learning to choose cleverly at each step which simulation trials to run next based on the results of previous trials. SIM_EXPLORE is a new computer program that uses directed exploration to explore efficiently complex systems represented by numerical simulations. The software sequentially identifies and runs simulation trials that it believes will be most informative given the results of previous trials. The results of new trials are incorporated into the software's model of the system behavior. The updated model is then used to pick the next round of new trials. This process, implemented as a closed-loop system wrapped around existing simulation code, provides a means to improve the speed and efficiency with which a set of simulations can yield scientifically useful results. The software focuses on the case in which the feedback from the simulation trials is binary-valued, i.e., the learner is only informed of the success or failure of the simulation trial to produce a desired output. The software offers a number of choices for the supervised learning algorithm (the method used to model the system behavior given the results so far) and a number of choices for the active learning strategy (the method used to choose which new simulation trials to run given the current behavior model). The software also makes use of the LEGION distributed computing framework to leverage the power of a set of compute nodes. The approach has been demonstrated on a planetary science application in which numerical simulations are used to study the formation of asteroid families.

Burl, Michael↗

DOE OSTI2024

Design and Manufacturing of High Performance, Reduced Charge Heat Exchangers

Air-to-fluid heat exchangers (HXs) play a critical role as the main heat transfer component in Heating, Ventilation, Air-Conditioning, and Refrigeration (HVAC&R) systems. However, their airside thermal resistance significantly inhibits their overall performance. Furthermore, these HXs must be continually more compact to meet the latest refrigerant charge limits to reduce emissions. Recent literature suggests that traditional HX geometries (e.g., round or flat tubes with fins), have reached their limits, and more sophisticated shape- and topology-optimized designs are required to achieve the next jump in performance. This research sheds light on the next generation of air-to-refrigerant HXs and aims to address several practical issues to commercialization such as novelty challenges (improved performance for significant charge reduction; modeling expertise & time investment), manufacturing challenges (non-round tube manufacturing; tube-header integration; product qualification, e.g., burst pressure testing, extreme operational environment, etc.), and operational challenges (flow maldistribution, fouling & wetting, noise & vibration). For example, a >20% improvement on one (or more) HX-level performance metrics (e.g., envelope volume, airside pressure drop, face area, capacity, refrigerant charge, weight, cost, etc.) must be achieved before a HX design is considered for commercialization. We present a new, comprehensive and experimentally validated air-to-refrigerant HX optimization framework with simultaneous thermal-hydraulic performance and mechanical strength considerations for novel, non-round, shape- and topology-optimized tubes capable of optimizing single and two-phase HX designs for any refrigerant choice and performance requirement with significant engineering time savings compared to conventional design practices. The framework was exercised for a wide range of applications and refrigerants, resulting in HXs which achieved greater than 20% improved performance, 20% reductions in size, and 25% reductions in refrigerant charge. To enable non-round tube bundle use in next generation HVAC&R equipment, novel manufacturing techniques were investigated, including the development of conventional manufacturing methods for small diameter, non-round tubes and novel tube-header integration strategies. In total, ten HX prototypes were manufactured, nine using conventional methods directly attributed to this project and one using advanced additive manufacturing methods. The five-year manufacturing feasibility of the proposed HXs was found to have a good outlook. The non-round tube HX simulated performance was validated through comprehensive experimental testing, including nine in-house component-level tests, one independent component-level test at an industry partner laboratory, and in-house system-level tests of using a commercially-available, residential packaged A/C unit which was retrofitted with a non-round tube prototype HX. It was found that HX designs proposed by the new framework can successfully predict experimental thermal-hydraulic performance within ±10-20% the first time with no manual design changes, eliminating the need for time-consuming and expensive prototyping efforts. This work will accelerate design and time to market for next generation HXs while simultaneously facilitating industry transition to new refrigerants at lower charge.

42 ENGINEERING↗

NASA NTRS2008

Lunar Outpost Life Support Trade Studies

Engineering trade-off studies of life support system architecture and technology options were conducted for potential lunar surface mission scenarios within NASA's Constellation Program. The scenarios investigated are based largely on results of the NASA Lunar Architecture Team (LAT) Phase II study. In particular, the possibility of Hosted Sortie missions, the high cost of power during eclipse periods, and the potential to reduce life support consumables through scavenging, in-situ resources, and alternative EVA technologies were all examined. These trade studies were performed within the Systems Integration, Modeling and Analysis (SIMA) element of NASA's Exploration Life Support (ELS) technology development project. The tools and methodology used in the study are described briefly, followed by a discussion of mission scenarios, life support technology options and results presented in terms of equivalent system mass for various regenerative life support technologies and architectures. Three classes of repeated or extended lunar surface missions were investigated in this study along with several life support resource scenarios for each mission class. Individual mission durations of 14 days, 90 days and 180 days were considered with 10 missions assumed for each at a rate of 2 missions per year. The 14-day missions represent a class of Hosted Sortie missions where a pre-deployed and potentially mobile habitat provides life support for multiple crews at one or more locations. The 90-day and 180-day missions represent lunar outpost expeditions with a larger fixed habitat. The 180-day missions assume continuous human presence and must provide life support through eclipse periods of up to 122 hours while the 90-day missions are planned for best-case periods of nearly continuous sunlight. This paper investigates system optimization within the assumptions of each scenario and addresses how the scenario selected drives the life support system to different designs. Subsequently, these analysis results can be used to determine which technologies may be good choices throughout a broad range of architectures.

Lange, Kevin E.↗

DOE OSTI2022

A Biomass Pyrolysis Oil as a Novel Insect Growth Regulator Mimic for a Variety of Stored Product Beetles

Abstract As fumigants face increasing regulatory restrictions, resistance, and consumer pushback, it is vital to expand the integrated pest management (IPM) chemical toolkit for stored products. The production of biomass derived insecticides (e.g., bio-oil fraction) from byproducts of biofuel production may be a promising alternative source of chemistries for controlling stored product insects. These potential insecticidal bio-oils were fractionated based on boiling points (ranging from 115 to 230°C in one series and 245–250°C in another). Fractions were analyzed using GC-MS, and were found to be unique in composition. The lethality of these fractions was tested on Tribolium castaneum, Tribolium confusum, and Oryzaephilus surinamensis (L.) (Coleoptera: Silvanidae). Fractions were tested at concentrations ranging from 5–260 mg/ml to screen for efficacy against adults for durations of 2–8 hr sprayed on concrete arenas. In addition, a separate assay evaluated adult emergence of larvae after 6 wk with supplemental food in arenas, while repellency was evaluated against four stored product insect species in a laminar wind tunnel. A greenhouse gas (GHG) emissions life cycle assessment was also performed, which found the use of the bio-oil fraction could reduce GHG emissions associated with the insecticide supply chain by 25–61% relative to a fossil-fuel based insecticide or pyrethroid. While adults were largely unaffected, we found that larval emergence was significantly suppressed compared to controls by roughly half or more. We also determined that there was minimal repellency to most fractions by most species. We conclude that the use of bio-oil fractions is a climate-friendly choice that may support IPM programs.

09 BIOMASS FUELS↗

DOE OSTI2020

Will Solar Panels Help When the Power Goes Out? Planning for PV Resilience

PV systems, like all energy systems, must chart a difficult course in order to improve resilience. They need to simultaneously withstand extreme conditions that cause grid power disruptions, be configured in a way that allows electricity to be delivered to meet the PV user's needs, and overcome disruptions arising from solar resource intermittency. Certain considerations reveal themselves as key to a PV system's resilience benefits. Choice of hardware is critical, as is site selection for the PV array. Voluminous evidence in a hurricane context demonstrates that durable hardware, properly maintained and sited, leads to PV systems surviving extreme weather with their functionality intact. Structurally weak or poorly maintained PV equipment, on the other hand, has demonstrated failures during extreme weather events. PV system stakeholders should ensure that best practices are followed for hardware procurement and siting. It is also important to understand that PV systems are not one-size-fits-all. While incorporating islanding capabilities and energy storage into the system's electrical topology will typically enhance resilience, the user's needs will determine the optimally resilient conformation of any given system. These factors - appropriate hardware, siting, maintenance, and system design - are the primary drivers of PV resilience. PV systems possess high potential for resilient energy generation due to their distributed, abundant, and free fuel supply, but the technology itself does not inherently lead to resilient outcomes. Realizing PV's potential for resilience requires consideration of these determinative factors.

14 SOLAR ENERGY↗

DOE OSTI2020

Subtask 1.5 – CO2 Injection Monitoring with an Optimized Scalable, Automated, Semipermanent Seismic Array

The scalable, automated, semipermanent seismic array (SASSA) method is a flexible and relatively cost-effective surface geophysical method for regular time-lapse monitoring of the movement of injected carbon dioxide (CO2) in a reservoir for CO2 enhanced oil recovery (EOR) or geologic CO2 storage operations. It has the advantages of a low-environmental-footprint while monitoring regions of a reservoir from the surface without the need for a regular grid distribution of receivers. Automated data collection is possible. As only time-lapse amplitude changes at the reservoir level due to CO2 movement within the reservoir are monitored, the turnaround time to deliver results from the SASSA method can be short, without the need for long, time-consuming data-processing workflows. As data is collected and processed, incremental information can be provided to the field operator. The Energy & Environmental Research Center (EERC) conducted a SASSA field test from September 2018 to November 2020 in a portion of the Bell Creek Field in Montana, which implemented new CO2 EOR field activities during the study period. Lessons learned from a proof-of-concept study were incorporated to improve the data quality of the SASSA method and demonstrate the viability of the technology. The EERC implemented several enhancements to improve data quality, including 1) an iterative survey design, which allowed placing the receivers in strategic locations where the movement of the CO2 in the reservoir could be tracked with minimum interference by the cultural noise in the study area; 2) the use of powerful seismic sources in the form of surface orbital vibrators, and 3) data acquisition during optimal periods. History-matched reservoir simulation was performed to predict gas saturation and pressure response induced by CO2 injection in the study area. The results were compared with the SASSA-measured responses to CO2 injection as a partial validation technique. A match between the two methods was observed for most of the SASSA points predicted to have intersected a CO2 saturation change. The validated results provide confidence that the SASSA method can be used independently as a CO2 saturation monitoring technique. As data are collected and processed, incremental information can be provided to the field operator. The critical components of the SASSA workflow for a successful application of the method are the following: Iterative survey design with information about CO2 injection activities from the oilfield operator. A detailed CO2 injection plan is the key driver to select the strategic monitoring location of the SASSA sensors. After this information is incorporated in the initial distribution of sources and receivers in the study area, high-resolution satellite images are used to identify ground locations not affected by cultural noise sources, such as power lines, pipelines/flow lines, or roadways. In the next iteration of the survey design, a scouting trip to the study area is needed to understand more details of the noise sources identified in the previous step and the intensity of the field activities that can also generate noise during the monitoring. Integrating the information from the scouting trip into the survey design to select the optimum source and receiver locations is the final step. Noise attenuation. The variety of noise types during seismic monitoring of an oil field is enormous. Tailored noise characterization and processing at a node-by-node level can enhance the performance and sensitivity of the SASSA technique. Future advancements that could improve the efficiency and application of the SASSA technology include: Gaining a better understanding of the noise field produced by the seismic source to aid the choice of receiver location. Surface noise from the source can overwhelm the small signal changes due to CO2 that the SASSA method measures. Improved data-processing workflow to automatically analyze and adapt to dynamic noise conditions associated with industrial settings. This subtask was funded through the EERC–DOE Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE- FE0024233.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗