Search NASA⌕ Search

SEARCH · Search NASA

Results for “data base for model validation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Performance evaluation of a wrapped around condenser for heat pump water heater applications

In this report, accurate performance evaluation of a wrapped-around condenser for heat pump water heaters (WHPWH) is critical since the COP of the system depends heavily on thermal stratification and condenser design. An analytical, quasi-steady state heat balance method has been developed to determine the optimal spacing between adjacent channels, tube diameter, tube shape, and total refrigerant charge amount for the condenser. The heat transfer rate is compared among three approaches: the refrigerant thermodynamic model, the condenser-wrap fin model, and the analytical natural convection model on the inside of the tank for the three regions based on the refrigerant phase (e.g., super-heated, saturated, or subcooled). The heat transfer rate was predicted by a combination of slug-plug and annular flow for a D-shaped helical tube. Experimental data were used as boundary conditions for validating the model. The rate of heat transfer based on tube shape and tank wall temperatures was compared by CFD analysis. Parametric analysis indicates a tradeoff between refrigerant mass, pressure drop, tube diameter, and tube length to maximize the heat transfer rate. The model suggests the saturated region length can be extended by 400%, and the condenser pressure drop can be reduced by 23% with an optimal spacing pattern.

42 ENGINEERING↗

Prediction of Cooling Curves for Controlled Unidirectional Solidification Under the Influence of Shrinkage: A Semi-analytical Approach

Quality of casting products can be significantly improved by controlling the crystal growth rate. Both dendritic and equiaxed grain structures depend strongly on crystal growth rate along the crystallographic direction. Uncontrolled solidification processes may lead to the formation of porous and columnar material with an extremely non-homogeneous composition distribution. These undesirable micro-structures can be avoided by adopting an optimal cooling rate (K/s) during the crystal growth. The present work focuses on determining suitable cooling curves to obtain desired unidirectional crystal growth rates, by implementing a semi-analytical model. Here, we defined cooling curve as the time history of temperature evolution at the cold boundary. The proposed semi-analytical heat transfer model is diffusion driven and accounts for shrinkage effect during solidification. The proposed model is found capable of predicting cooling curves for prescribed interface velocities. The model is self-sufficient in validating itself by means of solving inverse and forward problems. The cooling curve prediction by the model is validated by using it as the transient boundary condition for an existing enthalpy updating scheme-based numerical model. The proposed model is also applied to empirical data reported in literature, to validate the model against experimental results. All the validations showcased excellent fit. The proposed model will facilitate controlled unidirectional crystal growth rate by providing cooling rate (K/s) as an input for the experiments involving directional solidification.

36 MATERIALS SCIENCE↗

Predeployment progress of the Canister Deposition Field Demonstration

This report updates the high-level test plan for evaluating surface deposition on three commercial 32PTH2 spent nuclear fuel (SNF) canisters inside NUTECH Horizontal Modular Storage (NUHOMS) Advanced Horizontal Storage Modules (AHSMs) from Orano (formerly Transnuclear Inc.) and provides a summary of the surface sampling activities that have been conducted to date. The details contained in this report represent the best designs and approaches explored for testing as of this publication. Given the rapidly developing nature of this test program, some of these plans may change to accommodate new objectives or requirements. One goal of this testing is to collect defensible and detailed dust deposition measurements from the surface of dry storage canisters in a marine coastal environment to guide chloride-induced stress corrosion cracking (CISCC) research. Another goal is to provide data for the validation of computational fluid dynamics (CFD) based deposition modeling. To facilitate surface sampling, the otherwise highly prototypic dry storage systems will not contain SNF but rather will be electrically heated to mimic the decay heat and thermal hydraulic environment. Test and heater design is supported by detailed CFD modeling. Instrumentation throughout the canister, storage module, and environment will provide extensive information about the thermal-hydraulic behavior of horizontal dry cask storage systems. Manual sampling over a comprehensive portion of the canister surface at regular time intervals will offer detailed quantification and composition of the deposited particulates from a realistic storage environment. Discussions of a potential host site for the Canister Deposition Field Demonstration (CDFD) are ongoing. Until a host site is chosen, testing of key CDFD hardware components including the heater assemblies, power skid, and remote data acquisition system will continue. Functional testing of the finalized heater assemblies and test apparatus started this fiscal year. These initial heater tests have shown the assemblies are performing within design specifications. Staged surface sampling of a mockup of a canister outside the AHSM on a transfer skid was also performed. Refinements to the sampling procedures and techniques were captured from observation of these activities and lessons-learned debriefs. These updated sampling procedures and techniques are planned to be tested again in the field using the mockup in order to assure personnel are using the most accurate and repeatable methods possible prior to deployment for actual CDFD testing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Application of NCRP 156 Wound Models for the Analysis of Bioassay Data from Plutonium Contaminated Wound Cases

The NCRP 156 wound model was heavily based on data from animal experiments. The authors of the report acknowledged this limitation and encouraged validation of the models using data from human wound exposures. The objective of this paper was to apply the NCRP 156 wound models to the bioassay data from four plutonium-contaminated wound cases reported in the literature. Because a wide variety of forms of plutonium can be expected at a nuclear facility, a combination of the wound models—rather than a single model—was used to successfully explain both the urinary excretion data and wound retention data in three cases. The data for the fourth case could not be explained by any combination of the default wound models. While this may possibly be attributed to the existence of a category of plutonium whose solubility and chemistry are different than those described by the NCRP 156 default categories, the differences may also be the result of differences in systemic biokinetics. Lastly, the concept of using a combination of biokinetic models may be extended to inhalation exposures as well, where more than one form of radionuclide—particles of different solubility or different sizes—may exist in a workplace.

60 APPLIED LIFE SCIENCES↗

Predicting departure from nucleate boiling with advanced data- and physics-driven approaches

The subcooled and low-quality saturated flow boiling critical heat flux (CHF) corresponding to the departure from nucleate boiling (DNB) is one of the major limiting factors in the design and operation of pressurized water reactors (PWRs). Due to lack of agreement on its physical mechanisms, development of an accurate DNB-type CHF model has been elusive. The various steady-state (SS) predictive tools that have been proposed can be grouped into two categories: (1) data-driven methods—namely best-fit empirical correlations and look-up tables that result in relatively good agreement with specific experimental datasets but often fail to extend beyond their ranges of validity, and (2) the physics-based mechanistic models that rely on reasonable yet limited understanding of the underlying physics and apply constitutive relations to close the conservation equations. On one hand, with recent advances in computational capabilities and optimization techniques, machine learning (ML)-based methods constitute an alternative and a more advanced, data-driven approach. With enough data, they can be particularly useful in engineering fields where the physical phenomena are complex and challenging to model. On the other hand, a state-of-the-art physics-driven approach would not only provide more accurate prediction of SS CHF, but it would also help better understand and model transient applications. The data-driven regression models use deep feed-forward neural networks (NNs) and random forests to cross-validate with 1,865 CHF test cases, covering a wide range of flow conditions and channel geometries. The best-estimate ML-based predictors compare favorably with the widely used look-up table for annulus and plate, and sensitivity analysis has confirmed their effectiveness. The key advantage of ML-based methods is their online extensibility of applicability domain. The proposed physics-driven approach combines key assumptions and parameters in the relatively well-accepted theories of liquid sublayer dryout and near-wall bubble crowding. A more realistic understanding of local mechanisms has been modeled. The new model has been optimized and validated against 1,439 tube data, and it shows considerably improved performance when compared to a recent mechanistic model, demonstrating unbiased close agreement with measurements over a wide range of operating conditions. Future work will extend the improved physics-driven model to non-tube geometry applications and will couple the model with ML via a hybrid approach. The mechanistic SS work will also serve to improve understanding and to model transient CHF scenarios.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

NREL Evaluates Performance of Hydraulic Hybrid Refuse Vehicles

This highlight describes NREL's evaluation of the in-service performance of 10 next-generation hydraulic hybrid refuse vehicles (HHVs), 8 previous-generation (model year 2013) HHVs, and 8 comparable conventional diesel vehicles operated by Miami-Dade County's Public Works and Waste Management Department in southern Florida. Launched in March 2015, the on-road portion of this 12-month evaluation focuses on collecting and analyzing vehicle performance data - fuel economy, maintenance costs, and drive cycles - from the HHVs and the conventional diesel vehicles. The fuel economy of heavy-duty vehicles, such as refuse trucks, is largely dependent on the load carried and the drive cycles on which they operate. In the right applications, HHVs offer a potential fuel-cost advantage over their conventional counterparts. This advantage is contingent, however, on driving behavior and drive cycles with high kinetic intensity that take advantage of regenerative braking. NREL's evaluation will assess the performance of this technology in commercial operation and help Miami-Dade County determine the ideal routes for maximizing the fuel-saving potential of its HHVs. Based on the field data, NREL will develop a validated vehicle model using the Future Automotive Systems Technology Simulator, also known as FASTSim, to study the impacts of route selection and other vehicle parameters. NREL is also analyzing fueling and maintenance data to support total-cost-of-ownership estimations and forecasts. The study aims to improve understanding of the overall usage and effectiveness of HHVs in refuse operation compared to similar conventional vehicles and to provide unbiased technical information to interested stakeholders.

33 ADVANCED PROPULSION SYSTEMS↗

Study of Thermomechanical Behavior of Zirconium-0.3 Tin Alloy

Zirconium-based alloys are used in the manufacturing of nuclear fuel tubes. These tubes need to be clad with zirconium-tin (Zr-0.3 wt.% Sn) alloy to enhance the lives of tubes. Manufacturing of such clad tubes is a challenging task, due to work hardening and dynamic softening phenomenon. In this study, hot deformation behavior of Zr-0.3Sn alloy is investigated at different temperatures and strain rates. It is found that fully recrystallized microstructure can be obtained by working at around 900 °C and high strain rate of 10 s{sup −1}. Further, constitutive equations are developed for the entire domain of deformation range and fitted into standard FEM-based simulation model for extrusion. The simulation results are validated with experimental data. The difference in flow stresses values obtained from numerical and experimental methods was around 14%.

36 MATERIALS SCIENCE↗

Wood Decomposition: Understanding Processes Regulating Carbon Transfer to Soil Carbon Pools Using FACE Wood at Multiple Scales

Dead wood comprises approximately 20% of forest biomass. While it is widely recognized for its role in ecosystem functions relative to habitat and nutrient cycling, there are considerable uncertainties associated with its role in the forest carbon (C) cycle. The principal uncertainty is whether dead wood contributes to the soil C pool. With little supporting evidence, the presumption is that C in wood is respired back to the atmosphere through decomposition processes. The inability to attribute forest soil C to its source components has been a barrier to addressing this important forest carbon cycle question. The U.S. Dept. of Energy’s Free Air CO 2 Enrichment (FACE) experiment produced wood that has a distinct δ 13 C signature that can be used to trace its fate through organic matter decomposition processes. Using two hardwood species (aspen, birch) from the Rhinelander FACE site and pine from the Duke FACE site, the FACE Wood Decomposition Experiment (FWDE) was established in 2011 to provide the foundation for addressing wood decomposition and its associated processes at the continental scale. Plots were installed on nine experimental forests representing a range in bioclimatic forest conditions within the continental U.S. Each identical plot has logs of the three species incubating on the soil surface and pine logs suspended in the air, representing standing dead wood. Abiotic conditions are monitored continuously, and soil and forest conditions characterized. Logs on the sites have been measured every two years to assess decay. This project was initiated in 2016 with specific objectives to: (a) determine whether dead wood C contributes to the soil C pool, (b) assess the fungal community composition mediating the decay, (c) assess the interactions of termites with microbial decay, and (d) develop a mechanistic model to simulate wood decomposition. The principal field sampling was conducted in 2017; correspondingly, the results reported here represent six years of decomposition. Wood decomposition varied from 13 to 75 % loss across the bioclimatic gradient. Sites in the southeastern U.S. coastal plain and piedmont had fastest decomposition rates for each of the species. In contrast sites in the Rocky Mountains had the slowest decay rates, which were associated with cold temperatures. Standing deadwood decomposes at a much slower rate than logs on the soil surface; a response due to differences in wood moisture content. Wood carbon was measured in the mineral soil across each of the sites; accordingly, this is the first study to affirm that a portion of the wood C does become part of the soil C pool. Averaged across the FWDE sites, approximately 1.4% of the soil C in the upper 10 cm of the mineral soil directly beneath the log was derived from the deadwood; within 50 cm of the log, wood C accounted for an average of 2.1%. These results demonstrate that the contribution of deadwood to the soil C pool is a soil volume surrounding the log; and it’s likely a larger volume than what we sampled. We also hypothesized that there would be more wood C in the mineral soil when termites were present. However, that hypothesis wasn’t supported by measurements on the Santee Experimental Forest termite exclusion (SEF-TX) plots under FACE logs that incubated for 6 years. Across all the sites, the majority of the wood C was transferred to the atmosphere. Approximately 7,000 fungal species were sequenced. The fungal communities were different among each of the sites suggesting local colonization; interestingly, within sites the three species also exhibited differences in fungal community composition. White rot was the dominant fungal form in pine and hardwood, which yields less lignin in the wood residue. Brown rot occurred in approximately 20% of the pine and aspen logs, and it did not occur in birch logs. The occurrence of brown rot was only weakly correlated to site factors. We conducted two additional experiments to assess the effects of termites on wood decomposition and the associated interactions with the fungal community. Pine and birch logs were incubated on the Santee Experimental Forest termite exclusion plots in upland and riparian settings. There was no difference in decay between areas where termites were able colonize and plots where they had been excluded. Highly variable foraging by termites was a primary contributor the result. Correspondingly, fungal communities did not vary on logs incubated among the two treatments, but they did reflect site and species differences. The second experiment was conducted on each of the nine FWDE sites where pine and birch wood blocks were incubated for two years with and without a wrapping designed to exclude termites and other arthropods. The effects of termites on wood decomposition could be confirmed on two of the four sites known to have subterranean termites. On the two southeastern sites, termites contributed approximately 8% to mass loss in pine blocks over two years. A major factor clouding the role of termites in wood decomposition is the inability to assess the time, duration, and intensity of the foraging with the logs. Another uncertainty is related to whether a piece of wood will be foraged. A process-based wood decomposition model was developed representing biological processes mediated by fungi, bacteria, termites, beetles, as well as physical and chemical processes. The Coarse Wood Decomposition Model (CWDM) was parameterized based on a thorough review of the literature and it was validated using data from the FWDE. In the initial setup, the model considers softwoods and hardwoods groups, as opposed to individual species. Sensitivity analyses incorporating climate data from 89 locations in North America demonstrated that CWDM was stable from the tropics to the boreal zone. Model calibration and validation showed it to perform very well. The CWDM is poised for additional testing with subsequent FWDE data as well as other data sets, and it is available for incorporation into forest biogeochemical models or DOEs Earth System Modeling framework.

54 ENVIRONMENTAL SCIENCES↗

An Approach for Validating Actinide and Fission Product Burnup Credit Criticality Safety Analyses: Criticality (k eff ) Predictions

One of the most important remaining challenges associated with expanded implementation of burnup credit in the United States is the validation of depletion and criticality calculations used in the safety evaluation—in particular, the availability and use of applicable measured data to support validation, especially for fission products (FPs). Applicants and regulatory reviewers have been constrained by both a scarcity of data and a lack of clear technical basis or approach for use of the data. In this study, this paper describes a validation approach for commercial spent nuclear fuel (SNF) criticality safety (k eff ) evaluations based on best-available data and methods and applies the approach for representative SNF storage and transport configurations/conditions to demonstrate its usage and applicability, as well as to provide reference bias results. The criticality validation approach utilizes not only available laboratory critical experiment (LCE) data from the International Handbook of Evaluated Criticality Safety Benchmark Experiments and the French Haut Taux de Combustion program to support validation of the principal actinides but also calculated sensitivities, nuclear data uncertainties, and limited available FP LCE data to predict and verify individual biases for relevant minor actinides and FPs. The results demonstrate that (a) sufficient critical experiment data exist to adequately validate k eff calculations via conventional validation approaches for the primary actinides, (b) sensitivity-based critical experiment selection is more appropriate for generating accurate application model bias and uncertainty, and (c) calculated sensitivities and nuclear data uncertainties can be used for generating conservative estimates of bias for minor actinides and FPs. Results based on the SCALE 6.1 and the ENDF/B-VII.0 cross-section libraries indicate that a conservative estimate of the bias for the minor actinides and FPs is 1.5% of their worth within the application model. Finally, this paper provides a detailed description of the approach and its technical bases, describes the application of the approach for representative pressurized water reactor and boiling water reactor safety analysis models, and provides reference bias results based on the prerelease SCALE 6.1 code package and ENDF/B-VII nuclear cross-section data.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Capturing the spatial variability of noise levels based on a short-term monitoring campaign and comparing noise surfaces against personal exposures collected through a panel study

Highlights: • A Generalized Additive Model (GAM) was developed to generate noise exposure surfaces. • Noise data were collected based on short-term measurements in Toronto, Canada. • Various model specifications were tested in terms of the resulting predictions. • Predictions were validated against data from a panel and from a long-term campaign. • Models that involved manual adjustments resulted in more realistic surfaces. Environmental noise can cause important cardiovascular effects, stress and sleep disturbance. The development of appropriate methods to estimate noise exposure within a single urban area remains a challenging task, due to the presence of various transportation noise sources (road, rail, and aircraft). In this study, we developed a land-use regression (LUR) approach using a Generalized Additive Model (GAM) for LA{sub eq} (equivalent noise level) to capture the spatial variability of noise levels in Toronto, Canada. Four different model formulations were proposed based on continuous 20-min noise measurements at 92 sites and a leave one out cross-validation (LOOCV). Models where coefficients for variables considered as noise sources were forced to be positive, led to the development of more realistic exposure surfaces. Three different measures were used to assess the models; adjusted R{sup 2} (0.44–0.64), deviance (51−72%) and Akaike information criterion (AIC) (469.2–434.6). When comparing exposures derived from the four approaches to personal exposures from a panel study, we observed that all approaches performed very similarly, with values for the Fractional mean bias (FB), normalized mean square error (NMSE), and normalized absolute difference (NAD) very close to 0. Finally, we compared the noise surfaces with data collected from a previous campaign consisting of 1-week measurements at 200 fixed sites in Toronto and observed that the strongest correlations occurred between our predictions and measured noise levels along major roads and highway collectors. Our validation against long-term measurements and panel data demonstrates that manual modifications brought to the models were able to reduce bias in model predictions and achieve a wider range of exposures, comparable with measurement data.

54 ENVIRONMENTAL SCIENCES↗

SU-F-T-156: Monte Carlo Simulation Using TOPAS for Synchrotron Based Proton Discrete Spot Scanning System

Purpose: This study provides an overview of the design and commissioning of the Monte Carlo (MC) model of the spot-scanning proton therapy nozzle and its implementation for the patient plan simulation. Methods: The Hitachi PROBEAT V scanning nozzle was simulated based on vendor specifications using the TOPAS extension of Geant4 code. FLUKA MC simulation was also utilized to provide supporting data for the main simulation. Validation of the MC model was performed using vendor provided data and measurements collected during acceptance/commissioning of the proton therapy machine. Actual patient plans using CT based treatment geometry were simulated and compared to the dose distributions produced by the treatment planning system (Varian Eclipse 13.6), and patient quality assurance measurements. In-house MATLAB scripts are used for converting DICOM data into TOPAS input files. Results: Comparison analysis of integrated depth doses (IDDs), therapeutic ranges (R90), and spot shape/sizes at different distances from the isocenter, indicate good agreement between MC and measurements. R90 agreement is within 0.15 mm across all energy tunes. IDDs and spot shapes/sizes differences are within statistical error of simulation (less than 1.5%). The MC simulated data, validated with physical measurements, were used for the commissioning of the treatment planning system. Patient geometry simulations were conducted based on the Eclipse produced DICOM plans. Conclusion: The treatment nozzle and standard option beam model were implemented in the TOPAS framework to simulate a highly conformal discrete spot-scanning proton beam system.

60 APPLIED LIFE SCIENCES↗

SU-D-207-07: Implementation of Full/half Bowtie Filter Model in a Commercial Treatment Planning System for Kilovoltage X-Ray Imaging Dose Estimation

Purpose: To implement full/half bowtie filter models in a commercial treatment planning system (TPS) to calculate kilovoltage (kV) x-ray imaging dose of Varian On-Board Imager (OBI) cone beam CT (CBCT) system. Methods: Full/half bowtie filters of Varian OBI were created as compensator models in Pinnacle TPS (version 9.6) using Matlab software (version 2011a). The profiles of both bowtie filters were acquired from the manufacturer, imported into the Matlab system and hard coded in binary file format. A Pinnacle script was written to import each bowtie filter data into a Pinnacle treatment plan as a compensator. A kV x-ray beam model without including the compensator model was commissioned per each bowtie filter setting based on percent depth dose and lateral profile data acquired from Monte Carlo simulations. To validate the bowtie filter models, a rectangular water phantom was generated in the planning system and an anterior/posterior beam with each bowtie filter was created. Using the Pinnacle script, each bowtie filter compensator was added to the treatment plan. Lateral profile at the depth of 3cm and percent depth dose were measured using an ion chamber and compared with the data extracted from the treatment plans. Results: The kV x-ray beams for both full and half bowtie filter have been modeled in a commercial TPS. The difference of lateral and depth dose profiles between dose calculations and ion chamber measurements were within 6%. Conclusion: Both full/half bowtie filter models provide reasonable results in kV x-ray dose calculations in the water phantom. This study demonstrates the possibility of using a model-based treatment planning system to calculate the kV imaging dose for both full and half bowtie filter modes. Further study is to be performed to evaluate the models in clinical situations.

60 APPLIED LIFE SCIENCES↗

Prediction of thyroid C-cell carcinogenicity after chronic administration of GLP1-R agonists in rodents

Increased incidence of C-cell carcinogenicity has been observed for glucagon-like-protein-1 receptor (GLP-1r) agonists in rodents. It is suggested that the duration of exposure is an indicator of carcinogenic potential in rodents of the different products on the market. Furthermore, the role of GLP-1-related mechanisms in the induction of C-cell carcinogenicity has gained increased attention by regulatory agencies. This study proposes an integrative pharmacokinetic/pharmacodynamic (PKPD) framework to identify explanatory factors and characterize differences in carcinogenic potential of the GLP-1r agonist products. PK models for four products (exenatide QW (once weekly), exenatide BID (twice daily), liraglutide and lixisenatide) were developed using nonlinear mixed effects modelling. Predicted exposure was subsequently linked to GLP-1r stimulation using in vitro GLP-1r potency data. A logistic regression model was then applied to exenatide QW and liraglutide data to assess the relationship between GLP-1r stimulation and thyroid C-cell hyperplasia incidence as pre-neoplastic predictor of a carcinogenic response. The model showed a significant association between predicted GLP-1r stimulation and C-cell hyperplasia after 2 years of treatment. The predictive performance of the model was evaluated using lixisenatide, for which hyperplasia data were accurately described during the validation step. The use of a model-based approach provided insight into the relationship between C-cell hyperplasia and GLP-1r stimulation for all four products, which is not possible with traditional data analysis methods. It can be concluded that both pharmacokinetics (exposure) and pharmacodynamics (potency for GLP-1r) factors determine C-cell hyperplasia incidence in rodents. Our work highlights the pharmacological basis for GLP-1r agonist-induced C-cell carcinogenicity. The concept is promising for application to other drug classes. - Highlights: • An integrative PKPD model is applied to study GLP-1r agonist carcinogenicity. • C-cell carcinogenicity is impacted by both pharmacokinetics and pharmacodynamics. • The relation of GLP-1r stimulation and C-cell hyperplasia appears drug-independent. • Understanding carcinogenic risk needs a pharmacological basis.

60 APPLIED LIFE SCIENCES↗

OmicsMLMentor: A Web Application for Guided Machine Learning Analysis of Omics Data

Expression-based omics technologies (e.g. proteomics, metabolomics, transcriptomics, etc.) increasingly rely on supervised and unsupervised machine learning (ML) models to find key biomolecules distinguishing conditions, identify natural groupings in biological data, or generate predictions for outcomes of interest. Fitting ML models to omics data presents several challenges, including handling missing data, selecting a normalization method, choosing a valid model, and optimizing hyperparameters, all requiring statistical programming skills to address these challenges. Thus, the open-source web application SLOPE was designed to lower the barrier to ML modeling for omics data. SLOPE supports the fitting of 15 ML models (10 supervised and 5 unsupervised) tailored to omics datasets, such as proteomics, metabolomics, lipidomics, and transcriptomics. SLOPE offers several omics-specific features, including methods for handling missingness (imputation, conversion, removal), normalization tests, ranking of models based on the structure of a user’s data and user input, and optimal hyperparameter selections using cross-validation splits. By streamlining ML workflows for omics analysis, SLOPE address critical gaps in existing online web tools, facilitating a broader adoption of these models for omics research. Here, SLOPE is applied to data from a lignin exposure study to highlight the workflow for fitting both supervised and unsupervised models to data.

lipidomics↗

Systematic approach to verification and validation: High explosive burn models

Most material models used in numerical simulations are based on heuristics and empirically calibrated to experimental data. For a specific model, key questions are determining its domain of applicability and assessing its relative merits compared to other models. Answering these questions should be a part of model verification and validation (V and V). Here, we focus on V and V of high explosive models. Typically, model developers implemented their model in their own hydro code and use different sets of experiments to calibrate model parameters. Rarely can one find in the literature simulation results for different models of the same experiment. Consequently, it is difficult to assess objectively the relative merits of different models. This situation results in part from the fact that experimental data is scattered through the literature (articles in journals and conference proceedings) and that the printed literature does not allow the reader to obtain data from a figure in electronic form needed to make detailed comparisons among experiments and simulations. In addition, it is very time consuming to set up and run simulations to compare different models over sufficiently many experiments to cover the range of phenomena of interest. The first difficulty could be overcome if the research community were to support an online web based database. The second difficulty can be greatly reduced by automating procedures to set up and run simulations of similar types of experiments. Moreover, automated testing would be greatly facilitated if the data files obtained from a database were in a standard format that contained key experimental parameters as meta-data in a header to the data file. To illustrate our approach to V and V, we have developed a high explosive database (HED) at LANL. It now contains a large number of shock initiation experiments. Utilizing the header information in a data file from HED, we have written scripts to generate an input file for a hydro code, run a simulation, and generate a comparison plot showing simulated and experimental velocity gauge data. These scripts are then applied to several series of experiments and to several HE burn models. The same systematic approach is applicable to other types of material models; for example, equations of state models and material strength models.

36 MATERIALS SCIENCE↗

Data Validation Experiments with a Computer-Generated Imagery Dataset for International Nuclear Safeguards

Computer vision models have great potential as tools for international nuclear safeguards verification activities, but off-the-shelf models require fine-tuning through transfer learning to detect relevant objects. Because open-source examples of safeguards-relevant objects are rare, and to evaluate the potential of synthetic training data for computer vision, we present the Limbo dataset. Limbo includes both real and computer-generated images of uranium hexafluoride containers for training computer vision models. Here, we generated these images iteratively based on results from data validation experiments that are detailed here. The findings from these experiments are applicable both for the safeguards community and the broader community of computer vision research using synthetic data.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Calcination of kaolinite clay particles for cement production: A modeling study

Kaolinite rich clay particles calcined under certain conditions can attain favorable pozzolanic properties and can be used to substitute part of the CO{sub 2} intensive clinker in cement production. To better guide calcination of a clay material, a transient one-dimensional single particle model is developed, which fully addresses the conversion process of raw kaolinite particles suspended in hot gas. Particles are discretized into a number of spherical cells, on each of which mass, momentum, energy and species conservation equations are numerically solved by using the finite volume method. Reactions considered in the model include dehydration, dehydroxylation and various phase transformations. Thermogravimetric analysis is used to determine reaction kinetic data required as inputs in the model and to validate the model. Finally, model-based sensitivity analysis is performed, from which quantitative guidelines for calcination condition optimization are derived. - Highlights: • A general 1D mathematical model for single clay particle calcination is developed. • The model fully addresses momentum, heat and mass transfer and all the reactions. • Experiments are performed to determine kinetic data of the key reactions. • The model is verified by different means, including experimental results. • Sensitivity study is done to address key assumptions and derive useful guidelines.

36 MATERIALS SCIENCE↗

Empirical Validation of Building Energy Modeling using Flexible Research Platform

Recently, efforts have been made to provide reliable empirical data for ANSI/ASHRAE Standard 140, Standard Method of Test for the Evaluation of Building Energy Analysis Computer Programs, to enable improved accuracy of building energy model (BEM) engines and improved characterization of their accuracy. The motivation for this effort is that the use of reliable empirical validation data sets in the evaluation of building energy modeling tools will lead to more consistent and validated simulation engines across all software vendors. This would expedite the use of building energy modeling in designing new buildings and retrofitting existing buildings, which delivers more energy efficient buildings.As part of a three-year multi-lab empirical validation project sponsored by U.S. DOE, this research project generated cooling season test plans by reviewing ASHRAE Standard 140, and the tests were performed based on the test plan. Finally, the experimental data sets were compared with the EnergyPlus model to demonstrate the validation procedure.

Im, Piljae↗