Search NASA⌕ Search

SEARCH · Search NASA

Results for “direct energy conversion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Developing Stable Critical Materials and Microstructure for High-Flux and Efficient Hydrogen Production through Reversible Solid Oxide Cells

Reversible Solid Oxide Cells (RSOCs), which operate as either Solid Oxide Fuel Cells (SOFCs) or Solid Oxide Electrolytic Cells (SOECs), hold great promise for clean, high-efficiency energy conversion and hydrogen production. However, their commercial potential is hindered by stability issues arising from temperature-induced materials degradation. While substantial progress has been made in developing durable, reduced-temperature SOFCs - bringing them closer to commercial deployment, SOECs still exhibit substantially higher degradation rates at both the cell and stack levels under practical operating conditions.

08 HYDROGEN↗
DOE OSTI2021

Giant anomalous Nernst signal in the antiferromagnet YbMnBi 2

A large anomalous Nernst effect (ANE) is crucial for thermoelectric energy conversion applications because the associated unique transverse geometry facilitates module fabrication. Topological ferromagnets with large Berry curvatures show large ANEs; however, they face drawbacks such as strong magnetic disturbances and low mobility due to high magnetization. Herein, we demonstrate that YbMnBi 2 , a canted antiferromagnet, has a large ANE conductivity of ~10 A m –1 K –1 that surpasses large values observed in other ferromagnets (3–5 A m –1 K –1 ). The canted spin structure of Mn guarantees a non-zero Berry curvature, but generates only a weak magnetization three orders of magnitude lower than that of general ferromagnets. The heavy Bi with a large spin–orbit coupling enables a large ANE and low thermal conductivity, whereas its highly dispersive p x/y orbitals ensure low resistivity. The high anomalous transverse thermoelectric performance and extremely small magnetization make YbMnBi 2 an excellent candidate for transverse thermoelectrics.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

De novo Materials Design of Catalytic Surface Motifs for Water-Gas-Shift (Final Progress Report DOE Grant DE-SC0019281)

This project was aimed at developing innovative theoretical methods and models to understand essential catalysis-relevant issues such as CO 2 conversion, fuel cells, and lithium batteries. Through collaborations with experimentalists, we strive to develop new quantum and machine learning methods for the understanding of surface and interfacial chemistry that can empower the design of energy and sustainability systems. Overall, our work under this grant brings cross-disciplinary insights into catalytic materials, microenvironments, and other conditions, which can serve to provide design rules for the next generation of catalysts.

25 ENERGY STORAGE↗
DOE OSTI2026

Anodic Conversion of Cyclohexane, Methylcyclohexane, and 2-Propanol: Towards a Regenerable Liquid-Fed Fuel Cell

Liquid Organic Hydrogen Carriers (LOHCs) are promising for hydrogen and energy storage but require endothermic catalytic dehydrogenation. An alternative approach is a regenerable liquid-fed fuel cell which spontaneously converts an organic carrier from its hydrogen-rich to hydrogen-lean form while generating electrical power. The anodic electrooxidation of cyclohexane, methylcyclohexane and 2-propanol in a high temperature polybenzimidazole/phosphoric acid (PBI/PA) PEM fuel cell was investigated along with a quantitative analysis of reaction products. Cyclohexane and methylcyclohexane were predominantly converted to CO 2 with only a trace formation of the corresponding aromatic and cyclic olefin byproducts. This near-to-complete oxidation of the fuels is in sharp contrast to previous reports of a selective conversion of cyclohexane to benzene, with no CO 2 byproducts. In experiments with 2-propanol, acetone was produced, with diisopropylether, propylene and CO 2 as only minor side products. However, the extent of CO 2 formation greatly increased at higher current densities.

25 ENERGY STORAGE↗
DOE OSTI2022

Nanostructured carbon as highly efficient and stable anodes for ethylene production and power generation in protonic ceramic electrochemical cells

Protonic ceramic electrochemical cells (PCECs) have the potential in reducing the energy input and carbon emissions in ethylene production from ethane dehydrogenation. The performance of conventional perovskite-based anode materials for ethane conversion in PCECs is limited by their low active surface area and proneness to coke deposition. In this work, for the first time, we demonstrate the use of aligned carbon nanotube forests (CNTFs) as a novel anode material for an ethane fueled PCEC to co-produce ethylene and electricity. The CNTF electrode was grown on the electrolyte by the chemical vapor deposition (CVD) method. Highly dispersed iron carbide nanoparticles are formed in situ on the CNTFs during the CVD process, acting as highly active catalysts for ethane dehydrogenation. The novel PCECs show superior catalytic and electrochemical performances to that using conventional perovskite-based anodes. The cell also exhibits excellent durability and anti-coking abilities within 100 h test. This work showcases the promising application of nanostructured carbon, a new class of non-perovskite materials, as the multifunctional electrode materials for PCECs.

03 NATURAL GAS↗
DOE OSTI2022

Surface restructuring of a perovskite-type air electrode for reversible protonic ceramic electrochemical cells

Reversible protonic ceramic electrochemical cells (R-PCECs) are ideally suited for efficient energy storage and conversion; however, one of the limiting factors to high performance is the poor stability and insufficient electrocatalytic activity for oxygen reduction and evolution of the air electrode exposed to the high concentration of steam. Here we report our findings in enhancing the electrochemical activity and durability of a perovskite-type air electrode, Ba 0.9 Co 0.7 Fe 0.2 Nb 0.1 O 3-δ (BCFN), via a water-promoted surface restructuring process. Under properly-controlled operating conditions, the BCFN electrode is naturally restructured to an Nb-rich BCFN electrode covered with Nb-deficient BCFN nanoparticles. When used as the air electrode for a fuel-electrode-supported R-PCEC, good performances are demonstrated at 650 °C, achieving a peak power density of 1.70 W cm –2 in the fuel cell mode and a current density of 2.8 A cm –2 at 1.3 V in the electrolysis mode while maintaining reasonable Faradaic efficiencies and promising durability.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2026

Development of Composite Photocatalyst Materials that are Highly Selective for Solar Hydrogen Production and their Evaluation in Z-Scheme Reactor Designs

The key technology gap preventing a vertically stacked dual-bed particle suspension reactor from achieving the DOE MYRD&D ultimate cost target for H 2 production remains the lack of materials in particle form factor that exhibit ≥10% solar-to-H 2 energy conversion (STH) efficiency as a suspension. Therefore, our project goals centered around strategies to increase the STH efficiency by enhancing photophysical properties of perovskite oxide particles including increased visible-light absorption, increased selectivity for electrocatalysis of the H 2 evolution reaction (HER) and the O 2 evolution reaction (OER) through development of ultrathin oxide coatings, correlating composition and structure to function, and improving understanding of multiscale transport and kinetic processes.

08 HYDROGEN↗
DOE OSTI2023

Constructing a square-like copper cluster to boost C–C coupling for CO 2 electroreduction to ethylene

The CO 2 electroreduction reaction (CO 2 ER) to ethylene (C 2 H 4 ) offers the dual promise of lowering CO 2 emission while storing energy from renewable electricity, for which the development of highly efficient electrocatalysts is of great significance. Herein, by means of density functional theory (DFT) computations, we designed an electrocatalyst for CO 2 -to-C 2 H 4 conversion by anchoring a Cu 5 cluster supported on a MoS 2 monolayer with an S monovacancy (Cu 5 @MoS 2 ). Our results revealed that one Cu atom of the Cu 5 cluster was embedded into the framework of the defective MoS 2 monolayer, while the other four Cu atoms form a square-like island over the substrate surface. Interestingly, the C–C coupling between two *CO species can easily occur on the unique square-like active site with a low kinetic barrier of 0.56 eV to form the key *C 2 O 2 intermediate, which can then be hydrogenated to the C 2 H 4 product with a very low limiting potential (–0.32 eV). Significantly, alkaline conditions (pH = 13) are beneficial to further promote C 2 H 4 synthesis. Finally, our work may offer a new avenue to precisely modulate the structures of Cu clusters for converting CO 2 into high-value target products.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Carbon neutral manufacturing via on-site CO 2 recycling

The chemical industry needs to significantly decrease carbon dioxide (CO 2 ) emissions in order to meet the 2050 carbon neutrality goal. Utilization of CO 2 as a chemical feedstock for bulk products is a promising way to mitigate industrial emissions; however, CO 2 -based manufacturing is currently not competitive with the established petrochemical methods and its deployment requires creation of a new value chain. Here, we show that an alternative approach, using CO 2 conversion as an add-on to existing manufactures, can disrupt the global carbon cycle while minimally perturbing the operation of chemical plants. Proposed closed-loop on-site CO 2 recycling processes are economically viable in the current market and have the potential for rapid introduction in the industries. Retrofit-based CO 2 recycling can reduce annually between 4 and 10 Gt CO 2 by 2050 and contribute to achieving up to 50% of the industrial carbon neutrality goal.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Predictive model using artificial neural network to design phase change material-based ocean thermal energy harvesting systems for powering uncrewed underwater vehicles

Uncrewed Underwater Vehicles (UUVs) are a major beneficiary of the phase change material (PCM)-based ocean thermal energy harvesting technology for their mission needs. However, this technology relies on different parameters and energy conversion steps that could be critical to the general energy generation efficiency. Sea trials showed that the design performed lower than their laboratory design specifications. This underperformance results from different factors, mainly the UUV’s trajectory, travel time, underwater ocean currents, temperature fluctuations, and biofouling on the heat exchanger due to long term underwater operations. Therefore, there exists a need to continuously monitor the ambient energy harvesting system and predict system performance, for mission planning purposes. Two major parameters influencing the energy harvesting system include the final pressure inside the hydraulic energy storage vessel or accumulator, and the electrical load value. Here, this work focuses on the hydraulic to electric energy conversion system. Therefore, a combination of numerical model and experimental testing is used to develop a predictive model using artificial neural network using MATLAB. After validation with experimental testing, 1000 data samples obtained from the numerical model are used to train the ANN. Compared to the experimental results, the developed ANN model can predict in less than a second the designed benchtop system’s total efficiency with less than 15 percent maximum error range. This predictive model development represents a cost-effective way for optimization and a computational energy efficient mode aboard UUVs for mission planning for deployed UUVs using PCM-based ocean thermal energy harvesting technology.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Electrochemical Measurement of Water Transport Numbers in Anion-Exchange Membranes

Anion-exchange membranes (AEMs) are a possible replacement for perfluorosulfonic-acid membranes in energy-conversion devices, primarily due to the hydroxide mobile ion allowing the devices to operate in alkaline conditions with less expensive electrocatalysts. However, the transport properties of AEMs remain understudied, especially electro-osmosis. In this work, an electrochemical technique, where the open-circuit voltage is measured between two ends of a membrane maintained at different relative humidities, is used to determine the water transport number of various ionomers, including Versogen and Sustainion AEMs and Nafion cation-exchange membrane (CEM), as a function of water content and temperature. In addition, the CEMs and AEMs are examined in differing single-ion forms, specifically proton and sodium (CEM) and hydroxide and carbonate (AEM). Carbonate-form AEMs have the highest transport number (∼11), followed by sodium-form CEMs (∼8), hydroxide-form AEMs (∼6), and proton-form CEMs (∼3). Finally, a multicomponent transport model based on the Stefan-Maxwell-Onsager framework of binary interactions is used to develop a link between water transport number and water-transport properties, extracting a range for the unmeasured membrane water permeability of Versogen as a function of water content.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

A Cost-Performance Analysis of a Sodium Heat Engine for Distributed Concentrating Solar Power

We present that a sodium thermal electrochemical converter (Na-TEC) generates electricity directly from heat through isothermal expansion of sodium ions across a beta"-alumina solid-electrolyte. This heat engine has been considered for use with conventional concentrating solar power (CSP) systems before. However, unlike previous single-stage devices, the improved design uses two stages with an interstage reheat, allowing more economical and efficient conversion up to 29% at a hot side temperature of 850 °C. Herein, a cost-performance analysis for this improved design assesses opportunities for distributed-CSP in the context of micro-combined heat and power systems. A high-level techno-economic analysis (TEA) is presented that explores four scenarios where a Na-TEC is used as the heat engine for a distributed-CSP system. Overnight capital cost and levelized cost of electricity (LCOE) are estimated for a system lifetime of 30 years, revealing that overnight capital costs in a range from $3.57 to $17.71 per W e are feasible, which equate to LCOEs from 6.9 to 17.2 cents kWh e -1 . This analysis makes a significant contribution by concurrently quantifying the efficiency and unit costs for a range of multistage configurations, and demonstrating that a Na-TEC may be a promising alternative to Stirling engines for distributed-CSP systems at residential scale of 1–5 kW e .

14 SOLAR ENERGY↗
DOE OSTI2024

Direct conversion of methane to aromatics and hydrogen via a heterogeneous trimetallic synergistic catalyst

Abstract Non-oxidative methane dehydro-aromatization reaction can co-produce hydrogen and benzene effectively on a molybdenum-zeolite based thermochemical catalyst, which is a very promising approach for natural-gas upgrading. However, the low methane conversion and aromatics selectivity and weak durability restrain the realistic application for industry. Here, a mechanism for enhancing catalysis activity on methane activation and carbon-carbon bond coupling has been found to promote conversion and selectivity simultaneously by adding platinum–bismuth alloy cluster to form a trimetallic catalyst on zeolite (Pt-Bi/Mo/ZSM-5). This bimetallic alloy cluster has synergistic interaction with molybdenum: the formed CH 3 * from Mo 2 C on the external surface of zeolite can efficiently move on for C-C coupling on the surface of Pt-Bi particle to produce C 2 compounds, which are the key intermediates of oligomerization. This pathway is parallel with the catalysis on Mo inside the cage. This catalyst demonstrated 18.7% methane conversion and 69.4% benzene selectivity at 710 °C. With 95% methane/5% nitrogen feedstock, it exhibited robust stability with slow deactivation rate of 9.3% after 2 h and instant recovery of 98.6% activity after regeneration in hydrogen. The enhanced catalytic activity is strongly associated with synergistic interaction with Mo and ligand effects of alloys by extensive mechanism studies and DFT calculation.

03 NATURAL GAS↗
DOE OSTI2020

Modified alkaline peroxide pretreatment: An efficient path forward for bioethanol production from bamboo

To overcome the typical delignification saturation point of alkaline peroxide pretreatment and further facilitate lignin removal, a novel modified alkaline hydrogen peroxide pretreatment (MAHP) was proposed by introducing ethanol into the reaction system. The dosages of H 2 O 2 , ethanol, and pretreatment temperature were optimized, and the results revealed that a maximum lignin removal as high as 79.25% could be achieved at only 100 °C, 3 wt% H 2 O 2 concentration and 1 wt% ethanol concentration. Meanwhile, 76.5% of glucan and 56.0% of xylan were preserved at this pretreatment condition. By overcoming the delignification saturation point, enzymatic hydrolysis efficiency was remarkably enhanced, achieving 96.76% and 97.38% of glucan and xylan conversion, respectively, which are 7.4 and 11.4 times as compared to that of the untreated bamboo. Furthermore, the simultaneous saccharification and fermentation (SSF) result indicated an identical ethanol yield of ~75% when elevating the SSF solid loading from 5% to 30%. Based on the sequential SSF and xylose fermentation results, about 5.6 tons of bamboo would be consumed to produce 1 ton of ethanol. Finally, the energy balance revealed that a positive balance of 1255.4 KJ could be generated via processing 1 kg bamboo. Here, the results demonstrate that the MAHP is a promising high-efficiency pretreatment technology for bamboo due to the mild pretreatment severity and robust ethanol yield.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Degradation and recovery of solid oxide fuel cell performance by control of cathode surface acidity: Case study – Impact of Cr followed by Ca infiltration

Solid oxide fuel cells (SOFC) have attracted attention as clean and efficient energy conversion devices with low emissions. However, several degradation mechanisms limit the electrochemical performance of current SOFCs, with cathode degradation due to Cr-poisoning from metal interconnects particularly problematic. The acidity/basicity of binary additives has been found to be a sensitive descriptor of the oxygen exchange kinetics, indicating that acidic Cr-species/basic Ca-species can be expected to deactivate/activate the cathode surface, respectively. Inspired by recent advances, the feasibility of relative acidity as a tool for reviving degraded SOFCs is demonstrated by neutralizing Cr-poisoned SOFCs by subsequent serial infiltration of Ca-species. Furthermore, a model mixed ionic and electronic conducting oxide, Pr 0.1 Ce 0.9 O 2-δ (PCO), is selected as the cathode material. Area-specific resistances (ASR) of symmetric cells obtained by electrochemical impedance spectroscopy show that Cr-infiltration results in a seven-fold increase in ASR, while subsequent infiltration of Ca-species leads to complete recovery. Performance degradation and recovery are attributed to depressed/enhanced redox properties at the PCO surface, as supported by XPS analysis. Experiments using anode-supported fuel cells show a reduction in peak power density by 26% upon Cr-infiltration, reversed following Ca-infiltration, after which no degradation is observed during subsequent operation for 100 h.

(Pr,Ce)O2-δ↗
DOE OSTI2020

Chapter 3 - Harvesting Thermal Energy with Ferroelectric Materials

Thermal energy is considered the ubiquitous form of energy as all other forms of energy ultimately degrade to thermal energy. Thermal to electrical energy conversion is currently an important method for electricity generation. The traditional power cycles, however, become technically and economically unviable when heat source temperature reduces below 100 °C. Thermal energy harvesting has been proposed as a viable alternative for low-grade thermal to electrical energy conversion. Thermal energy harvesting is a method of generating electricity using temperature-induced variations in material properties. It is particularly useful when the heat sources are available free-of-cost, either in the form of natural heat or waste heat. While there are several thermal energy harvesting techniques, pyroelectricity is the most promising as it can be used in situations where spatial thermal gradients are difficult to establish or the temperature of the heat source is changing. Despite the fact that the pyroelectric effect in ferroelectric materials has been known for past several decades, thermal energy harvesting using ferroelectric materials has not been much explored in the literature. In this chapter, we would explore various aspects of thermal energy harvesting using ferroelectric materials. We have first established the physics behind ferroelectricity, then provided a detailed description on ferroelectric thermal energy harvesting, discussed various ferroelectric thermodynamic cycles and devices proposed in the literature, and finally described various other emerging applications of ferroelectricity.

DIRECT ENERGY CONVERSION,MATERIALS SCIENCE,OTHER I↗
DOE OSTI2021

Component Development for Alkaline URFCs

Performance, cost, and durability of the catalyst materials are the key factors that govern commercialization of H 2 -based energy conversion devices such as unitized regenerative fuel cells (URFCs). Compared to existing battery systems, URFCs offer superior energy density and performance over prolonged operation. In addition, alkaline URFC systems, can utilize low-cost platinum group metal-free (PGM-free) catalysts, resulting in much lower overall system costs. This project seeks to address the major obstacles faced in URFC systems such as cost and efficiency and establish a URFC technical capability through the strategic partnership between UofSC and SRNL. The research focuses on the development of low-PGM and PGM-free based bifunctional oxygen catalysts and electrodes, as well as the development of a URFC testing capability at SRNL.

25 ENERGY STORAGE↗
DOE OSTI2026

Empirical Comparison of Machine Learning Approaches for Black-Box Modeling of Power Conversion System Dynamics

Inverter-based resources are key components in modern power systems, but accurately modeling their complex behavior can be challenging. Standard, generic converter models often oversimplify inverter dynamics, leading to significant errors in predicting performance. In this work, we compare several data-driven machine learning (ML) approaches for inverter modeling, performing experiments on power conversion systems, systematically varying input conditions, and recording the resulting voltages and currents. The ML models were then trained on this measured data to capture the inverter's dynamic response and to predict the inverter's output current. A performance comparison between the four ML models under study is conducted, laying the foundation for future work on hardware implementation for real-time inference.

30 DIRECT ENERGY CONVERSION↗