Search NASA⌕ Search

SEARCH · Search NASA

Results for “divertor simulator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Inference of molecular divertor density from filtered camera analysis of molecularly induced Balmer line emission during detachment in JET L-mode plasmas

Here a previously presented Monte Carlo method for estimating local plasma conditions in 2D based on intensity ratios of deuterium Balmer D α , D γ and D ε lines was amended to consider also the D α and D γ emission contributions arising from molecular processes. The obtained estimates were used to infer the molecular divertor density with the help of the molecular databases of EIRENE. The method was benchmarked against EDGE2D-EIRENE simulations and observed to reproduce the molecularly induced emission fractions and the molecular divertor densities primarily within 25% of the references. Experimental analysis of a JET L-mode density scan suggested molecularly induced D α and D γ contributions of up to 60–70% and 20%, respectively, during the process of detachment. The independent estimates of the molecular divertor density inferred from the obtained molecularly induced D α and D γ intensities agree within uncertainties with each other. Both estimates show the molecular density increasing up to approximately 1.0–2.0 x 10 20 m -3 at the outer strike point in deep detachment with its ratio to the local electron density agreeing with EDGE2D-EIRENE predictions within the scatter of the experimental data.

interferometry↗
DOE OSTI2023

Performance Comparison of Helium and sCO 2 as Coolants for Modular Finger-Type Divertors

Several studies at the Georgia Institute of Technology have evaluated the thermal and fluids performance of the helium-cooled modular divertor with multiple jets (HEMJ) over the past decade. This finger-type divertor was studied both experimentally at nearly prototypical conditions and numerically at fully prototypical operating conditions using experimentally validated simulations. Recently, supercritical carbon dioxide (sCO 2 ) has been studied as the primary coolant in power cycles and other applications in various systems, in part because CO 2 achieves the high densities typical of supercritical fluids at relatively low temperatures and pressures, with a critical point of (7.38 MPa, 31°C). This density makes it possible to realize very compact and efficient sCO 2 power cycles. The feasibility of sCO 2 as a coolant for plasma-facing components, specifically the divertor, was therefore evaluated as part of the Fusion Energy System Studies design study activities. This work compares the thermal-fluid performance of helium and sCO 2 in the HEMJ divertor geometry using numerical simulations at prototypical conditions: inlet temperatures T i = 600°C to 700°C, pressures p ≈ 10 MPa, and steady-state incident heat fluxes on the tile q″ < 17 MW/m 2 . The performance is quantified here as the maximum heat flux that can be accommodated by the plasma-facing tile, the pumping power fraction, defined as the ratio of the coolant pumping power to the incident thermal power, and the operating stress limits based on ASME pressure vessel criteria. As expected, helium requires lower mass flow rates and pumping power fractions within imposed maximum temperature limits for the HEMJ pressure boundary. However, it also appears that neither helium nor sCO 2 can remove 10 MW/m 2 of incident heat flux while meeting ASME pressure vessel criteria. Finally, the numerical modeling reveals that sCO 2 may remove slightly higher incident heat fluxes than helium due to the imposed stress limits due to the sCO 2 coolant resulting in smaller local temperature gradients, albeit at a considerably higher pumping power fraction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Dependence of divertor turbulence on plasma density and current in TCV

To reliably predict the distribution of heat and particle fluxes at the target plates of tokamaks, a comprehensive understanding of turbulence throughout the entire Scrape-Off-Layer (SOL) is imperative. This study examines divertor turbulence systematically across a broad parameter range on the TCV tokamak, including variations in magnetic field direction, plasma current I p ∈ [140,320] kA, edge safety factor q 95 ∈ [2.6,4.7] and Greenwald fraction f G ∈ [0.18,0.6]. The TCV X-point Gas Puff Imaging (GPI) system is used to measure 2D filament properties in the inner and outer divertor region. The fluctuation levels in the divertor are found to strongly increase with density (to 80% over most of the SOL) while remaining insensitive to I p . The previously identified divertor-localized filaments (DLF), located on the bad curvature side of the outer divertor leg, are found to be a common feature on TCV, while no filaments are observed in the PFR. DLFs are present over most of the parameter space and in both field directions. However, they are absent, or appear only closer to the target, for sufficiently large Λ div ≳ 10 or q 95 ≳ 3.7. Across both I p and f G scans, some clear trends with Λ div are found for divertor filament sizes and velocities, and with target fall-off lengths of density and heat flux profiles at the outer target. This study provides important experimental insights to turbulent transport in the divertor also for comparison with self-consistent, turbulence simulations and extrapolation to future reactor conditions.

cross-field transport↗
DOE OSTI2022

$\mathrm{T}$ransient $\mathrm{CHI}$ System Design Studies for $\mathrm{P}$ EGASUS -$\mathrm{III}$

We report transient coaxial helicity injection (transient CHI), first developed on the Helicity Injected Torus-II (HIT-II) and later on the National Spherical Torus Experiment (NSTX) for implementing solenoid-free plasma current startup capability in a spherical tokamak (ST), is now planned to be tested on the Pegasus-III ST using a novel double-biased configuration. Such a configuration is likely needed for transient CHI deployment in a reactor. The transient CHI system optimization will be studied on Pegasus-III to enable startup toroidal persisting currents at the limits permitted by the external poloidal field coils. A transient CHI discharge is generated by driving injector current along magnetic field lines that connect the inner and outer divertor plates on one end of the ST. Simulations using the Tokamak Simulation Code are used to assess the transient CHI toroidal current generation potential and electrode gap location on the Pegasus-III. While past transient CHI systems have used high-voltage, oil-filled capacitors for driving the injector current, for improved safety, Pegasus-III will use a high-current capacitor bank based on low-voltage electrolytic capacitors. The designed and fabricated system is capable of over 32 kA. The modular design features permit the system to be upgraded to higher currents, as needed, to meet the future needs of the Pegasus-III facility.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Latent space mapping: Revolutionizing predictive models for divertor plasma detachment control

The inherent complexity of boundary plasma, characterized by multi-scale and multi-physics challenges, has historically restricted high-fidelity simulations to scientific research due to their intensive computational demands. Consequently, routine applications such as discharge control and scenario development have relied on faster but less accurate empirical methods. This work introduces DivControlNN, a novel machine-learning-based surrogate model designed to address these limitations by enabling quasi-real-time predictions (i.e., ~ 0.2 ms) of boundary and divertor plasma behavior. Trained on over 70,000 2D UEDGE simulations from KSTAR tokamak equilibria, DivControlNN employs latent space mapping to efficiently represent complex divertor plasma states, achieving a computational speed-up of over 10 8 compared to traditional simulations while maintaining a relative error below 20% for key plasma property predictions. During the 2024 KSTAR experimental campaign, a prototype detachment control system powered by DivControlNN successfully demonstrated detachment control on its first attempt, even for a new tungsten divertor configuration and without any fine-tuning. These results highlight the transformative potential of DivControlNN in overcoming diagnostic challenges in future fusion reactors by providing fast, robust, and reliable predictions for advanced integrated control systems.

Artificial neural networks↗
DOE OSTI2021

CFD Simulation of Helium Flow Loop Test Section

A helium flow loop is being assembled at Oak Ridge National Laboratory to analyze heat transfer enhancement for systems such as blanket and divertor components. To efficiently identify optimum geometries for heat transfer enhancement in these applications, simulation work is performed to optimize test section designs that are built and tested in the helium flow loop that operates at 4 MPa and a mass flow rate of 100 g/s. Different ribbed geometries that examine rib shape, rib height, rib orientation, rib spacing, and three dimensional orientation are modeled and simulated in STAR-CCM+ to compare their ability to remove heat and mitigate pressure drop. Following the simulations, models are selected and manufactured for the helium flow loop tests. Simulations initially focus on a hydrodynamic study to determine the appropriate mesh and physics models and then add a heat flux to analyze the heat transfer abilities of the models. The simulations are run in steady state and use a Reynolds-averaged Navier-Stokes k-ε turbulence model. The helium is modeled as an ideal gas. The simulation explores models of geometries that enhance the heat transfer and decrease pressure drop with an overall goal of increasing fluid collision with the wall. Enhanced geometries are simulated to select appropriate designs for manufacturing, and preliminary experimental results are used to validate the simulations. Furthermore, the factors that are being analyzed in the comparison between the experimental and the simulated results include matching thermocouple temperatures, pressure drop, roughness, and fluid velocity.

42 ENGINEERING↗
DOE OSTI2022

Validation of SOLPS-ITER simulations with kinetic, fluid, and hybrid neutral models for JET-ILW low-confinement mode plasmas

For JET L-mode plasmas in low-recycling conditions (electron temperature at the outer strike point, T e,ot ≳ 30 eV ), SOLPS-ITER simulations agree within the error bars for the experimental profiles at the low-field side (LFS) divertor target. The peak Balmer-α (Dα ) emission in the LFS divertor agrees within the error bars of the KS3 filterscope diagnostic, but is approximately 30% lower than the peak value of the KT1 spectrometer. Simulations have been performed with fluid, kinetic, and hybrid models for the neutrals. The large fluid-kinetic discrepancies of more than a factor 2 are successfully corrected by using a hybrid fluid-kinetic approach, for which kinetic atoms are transferred to the fluid population when the local Knudsen number of the atom becomes smaller than a user-defined transition Knudsen number Kn t . The hybrid-kinetic discrepancies are limited to a few % for Kn t ≤ 100 . When increasing the upstream density to high-recycling conditions, at the onset of detachment ( T e,ot ≈ 5 eV ), the simulations predict more than a factor 2 lower peak ion saturation current to the LFS divertor than the experiments. Also the Dα emission is underpredicted with approximately a factor 2. For these high-recycling conditions, the fluid-kinetic discrepancies are limited to maximum 50%, which are again corrected by using the hybrid approach.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Hermes-3

Hermes-3 is a plasma simulation model built on BOUT++, developed as part of research studies of the edge and divertor regions of magnetically confined fusion plasmas such as tokamaks. The main purpose of this model is multi-species simulation of plasmas containing a mixture of deuterium, tritium, helium and other plasma and neutral gas species.

Dudson, BenjaminD↗
DOE OSTI2021

SOLPS-ITER validation with TCV L-mode discharges

This work presents a quantitative test of SOLPS-ITER simulations against tokamak a configuration variable (TCV) L-mode experiments. These simulations account for drifts, currents, kinetic neutrals, and carbon impurities providing the most complete edge transport simulations for TCV to date. The comparison is performed on nominally identical discharges carried out to assess the effectiveness of TCV’s divertor baffles in the framework of the European Plasma Exhaust program and employs numerous edge diagnostics providing a detailed code-experiment benchmark for TCV. The simulations show a qualitative consistency, but the quantitative differences remain, which are assessed herein. It is found that, for a given separatrix density, the simulations most notably yield a colder, and denser, divertor state with a higher divertor neutral pressure than measured.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Monte Carlo Analysis of the Performance of the ITER Diagnostic Residual Gas Analyzer

The composition of exhausted gas is a key parameter in long-pulse plasma fusion experiments, and its evolution shall be monitored at timescales relevant to plasma dynamics and plasma-wall interactions. A diagnostic residual gas analyzer (DRGA) is a multisensor instrument particularly suited to these studies, and ITER will adopt DRGAs in the equatorial and in the divertor tokamak regions. In this work, we have revisited the design of the ITER divertor DRGA through simple vacuum analytical considerations supported by simulations conducted with Molflow+, a test particle Monte Carlo (TPMC) simulation code commonly used in the particle accelerator community. Here, starting with recommendations on the manufacturing of the vacuum piping of the DRGA, this work is followed by a complete vacuum characterization of the diagnostic vacuum setup (pressure profiles at base pressure and during sampling, orifice diameter, and length optimization), and finally, the in-vessel residence time of the most important gas species is simulated. These studies have allowed us to give insights into some experimental results recently found on the prototype DRGA installed in the Wendelstein W7-X stellarator.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Simulations of heat fluxes in an ELMy H-mode discharge on HL-2A

In order to study the distribution and evolution of the transient heat flux on HL-2A during edge-localized-mode (ELM) bursts, the BOUT++ electromagnetic six-field two-fluid model is used to simulate the pedestal collapse under the lower single-null divertor geometry. The equilibrium profiles of HL-2A ELMy H-mode discharge No. 24 953 are adopted as the initial condition in the original case. In this instance, linear analysis shows that the resistive ballooning mode (RBM) and drift-Alfven wave are unstable to this equilibrium, and RBM is the dominant instability. The evolutions of the radial heat fluxes at the outer mid-plane and heat fluxes to the inner and outer targets during the ELM event are presented. Six more equilibria are constructed based on the original case to find out the influence of the pedestal profiles on the peak electron heat flux. The results indicate that the heat flux increases with temperature and/or density, and the theoretical analysis and simulation results consistently show that the heat flux q ∥e is proportional to n e0,SEP $T^{\frac32}_{e0,SEP}$.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Experiments on plasma detachment in a V-shaped slot divertor in the DIII-D tokamak

Abstract Experiments in DIII-D demonstrate that the upstream plasma density to detach an un-pumped slot divertor is similar for a V-shaped and a flat-end slot, despite significantly higher neutral pressure in the V-shaped slot and in contrast to SOLPS-ITER predictions. The detachment threshold can be reduced by using in-slot instead of main-chamber gas fuelling or by placing the strike point on the inner slanted slot baffle instead of the slot end, as described by simulations with full drift physics. When increasing the plasma line-averaged density (without extrinsic impurities), the transition to detachment in DIII-D slot divertor is sharp and requires a high value of plasma density with the ion B → × ∇ B drift into the slot, whereas it is smooth and requires a lower value of plasma density with the opposite drift direction, in accord with detachment experiments in the DIII-D open lower divertor. Unique experiments on DIII-D and comparison to advanced simulations expand the scientific understanding of slot-shaped divertors, considered highly desirable for next step fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Validation of SOLPS-ITER and EDGE2D-EIRENE simulations for H, D, and T JET ITER-like wall low-confinement mode plasmas

Both experiments and simulations with SOLPS-ITER and EDGE2D-EIRENE show that the onset of detachment for the low-field side (LFS) divertor – defined here as the line-averaged upstream density (〈n e 〉 edge ) at which the plasma flux to the LFS target (I LFS-plate ) starts to decrease with increasing 〈n e 〉 edge – is independent of the isotope mass. However, there are three major simulation-experiment discrepancies: (i) the absolute values of I LFS-plate and the electron density (n e ) in the LFS divertor at the onset of detachment are significantly lower in simulations, i.e., approximately a factor of 2 for I LFS-plate and a factor of 3-4 for n e ; (ii) the degree of detachment – defined here as the difference between I LFS-plate at the onset of detachment and at an 〈n e 〉 edge value close to the density limit – is smaller in simulations compared to experiments; and (iii) the experimentally observed larger degree of detachment for D and T plasmas compared to H plasmas cannot be clearly distinguished from the simulation results. There are strong indications that discrepancy (i) is to a large extent caused by neglecting Lyman-opacity effects in our simulations. The simulations predict a similar net volumetric recombination source for all isotopes due to the fact that molecule-activated recombination (MAR) compensates for the reduced electron–ion recombination (EIR) for H, whereas MAR is negligible for D and T. This similar net volumetric recombination source for all isotopes leads to an isotope-independent degree of detachment in simulations. An analysis of the Balmer-α and Balmer-$γ$ emission confirms the underestimate of MAR in simulations (especially for D and T) for the JET metallic wall, which was previously observed for devices with a carbon wall. The underestimate of MAR is an important cause for discrepancy (ii) and the fact that there is a stronger underestimate of MAR for D and T than for H explains discrepancy (iii). Extending the plasma grid to the vessel wall increases I LFS-plate and n e at the onset of detachment by 25%, and the EIR source increases by 80% in detached conditions. Hence, while the extended grid results are closer to the experimental observations, the previously described qualitative discrepancies still persist.

Balmer emission↗
DOE OSTI2021

Simulation of the SPARC plasma boundary with the UEDGE code

Here in this work, the UEDGE edge transport code is used to examine conditions in the SPARC divertor and edge plasma for various levels of carbon impurity and power from the core (P SOL ). A double-null magnetic configuration is simulated assuming up-down symmetry in geometry and physics. The anomalous heat and particle transport coefficients are tuned to match empirical predictions for SPARC's midplane density profiles, target plate heat flux profiles, and inner/outer divertor power sharing. Convective transport is included on the low-field side, while on the high-field side the transport is modeled as purely diffusive. Hydrogen neutrals are modeled as a fluid with inertial effects, and a carbon impurity is included using the fixed-fraction model. We find that detachment induced by impurity seeding could significantly reduce the heat flux to the divertor surfaces in the SPARC tokamak. At P SOL = 28 MW (the value predicted for SPARC's full-power H-mode scenario) cases with both divertor legs detached were obtained with a carbon impurity fraction between 0.3%–1.4%, far below Z eff limits for SPARC. When the plasma in the outer leg is detached, the peak heat flux density perpendicular to the target plate is below 1 MW m -2 , electron and ion temperatures are less than 1.5 eV, and momentum detachment is observed. However, the detachment state is found to be sensitive to the side-wall boundary conditions, the level of neutral pumping, and the target plate tilt. Finally, a broadly similar SOLPS simulation of SPARC is used to assess the appropriateness of the simpler impurity and neutral models used in UEDGE.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

SOLEDGE3X full vessel plasma boundary simulations of ITER non-active phase plasmas

The onset of detachment in the ITER machine is analyzed in this work through the help of 2D-axisymmetric boundary plasma simulations with the SOLEDGE3X-EIRENE code, which features a numerical domain for the plasma solver extending up to the first wall. The plasma boundary is computed in scenarios from the first non-active phase of ITER, in pure H and at 20 MW. This set of simulations is used in two aspects: first, to study the plasma detachment in the divertor, and second, the plasma conditions, fluxes, and beryllium erosion at the first wall. Here, the code results are also compared to those obtained with the well-established SOLPS-ITER code, which includes a plasma numerical domain only covering the main SOL. Results show an increase in the SOL width λ q with increasing density, and a detailed analysis is carried out, for the first time, on each of the different plasma-neutral interactions in the code’s physics model in EIRENE. The gross beryllium erosion rates of first wall panels are estimated from 2D simulations, with the aim of assessing their sensitivity to two parameters: the divertor density regime, and the presence of density shoulders in the far-SOL formed by enhanced perpendicular transport at this location. The erosion contributions from neutrals and ions are considered in each case, and the charge-exchange atoms fluxes and energy distributions are provided, highlighting the two atom populations (cold and charge-exchange).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Turbulence spreading effects on the ELM size and SOL width

BOUT++ turbulence simulations were performed to investigate the impact of turbulence spreading on the edge localized mode (ELM) size and divertor heat flux width (λ q ) broadening in small ELM regimes. Here, this study is motivated by EAST experiments. BOUT++ linear simulations of a pedestal radial electric field (E r ) scan show that the dominant toroidal number mode (n) shifts from high-n to low-n, with a narrow mode spectrum, and the maximum linear growth rate increases as the pedestal E r well deepens. The nonlinear simulations show that as the net E × B pedestal flow increases, the pressure fluctuation level and its inward penetration beyond the top of the pedestal both increase. This leads to a transition from small ELMs to large ELMs. Both inward and outward turbulence spreading are sensitive to the scrape-off-layer (SOL) plasma profiles. The inward turbulence spreading increases for the steep SOL profiles, leading to increasing pedestal energy loss in the small ELM regime. The SOL width (λ q ) is significantly broadened progressing from the ELM-free to small ELM regime, due to the onset of strong radial turbulent transport. The extent of the SOL width (λ q ) broadening depends strongly on outward turbulence spreading. The fluctuation energy intensity flux Γ ε at the separatrix can be enhanced by increasing either pedestal E r flow shear or local SOL pressure gradient. The λ q is broadened as the fluctuation energy intensity flux Γ ε at the last close flux surface (LCFS) increases. Local SOL E × B flow shear will restrain outward turbulence spreading and the associated heat flux width broadening. Operating in H-mode with small ELMs has the potential to solve two critical problems: reducing the ELM size and broadening the SOL width.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Tokamak divertor plasma emulation with machine learning

Abstract Future tokamak devices that aim to create conditions relevant to power plant operations must consider strategies for mitigating damage to plasma facing components in the divertor. One of the goals of MAST-U tokamak operations is to inform these considerations by researching advanced divertor configurations that aid stable plasma detachment. Machine design, scenario planning and detachment control would all greatly benefit from tools that enable rapid calculation of scenario-relevant quantities given some input parameters. This paper presents a method for generating large, simulated scrape-off layer data sets, which was applied to generate a data set of steady-state Hermes-3 simulations of the MAST-U tokamak. A machine learning model was constructed using a Bayesian approach to hyperparameter optimisation to predict diagnosable output quantities given control-relevant input features. The resulting best-performing model, which is based on a feedforward neural network, achieves high accuracy when predicting electron temperature at the divertor target and carbon impurity radiation front position and runs in around 1 ms in inference mode. Techniques for interpreting the predictions made by the model were applied, and a high-resolution parameter scan of upstream conditions was performed to demonstrate the utility of rapidly generating accurate predictions using the emulator. This work represents a step forward in the design of machine learning-driven emulators of tokamak exhaust simulation codes in operational modes relevant to divertor detachment control and plasma scenario design.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Progress and innovations in the TCV tokamak research programme

Research on the Tokamak à Configuration Variable addresses a wide range of key questions relevant to ITER and future fusion power plants. Over the past two years, highly productive experimental campaigns have led to major advances across several areas: the ITER baseline scenario; pedestal properties in low-collisionality, peeling-limited conditions; and the development of high- β N , non-inductive regimes. Alternative high-confinement scenarios have likewise received significant attention, with remarkable progress in quasi-continuous exhaust operation, X-point radiator plasmas, and negative triangularity configurations. Substantial achievements were also made in the mitigation or benign termination of runaway electron beams, in elucidating fast-ion loss mechanisms, and in improving exhaust behaviour in both conventional and alternative divertor geometries. These experimental results have been strongly supported by advances in modelling and their direct application to the experiment, ranging from gyrokinetic simulations of core and pedestal turbulence to fluid-based studies of scrape-off layer and divertor physics in diverse geometries. Plasma control has taken on an increasingly important role, with model-based and data-driven approaches now closely intertwined with physics studies. This article provides a overview of these recent activities, together with a brief outlook on forthcoming upgrades and next steps.

EPFL↗