SEARCH · Search NASA

Results for “downstream passage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1983

The effect of incidence angle on the overall three-dimensional aerodynamic performance of a classical annular airfoil cascade

To be of quantitative value to the designer and analyst, it is necessary to experimentally verify the flow modeling and the numerics inherent in calculation codes being developed to predict the three dimensional flow through turbomachine blade rows. This experimental verification requires that predicted flow fields be correlated with three dimensional data obtained in experiments which model the fundamental phenomena existing in the flow passages of modern turbomachines. The Purdue Annular Cascade Facility was designed specifically to provide these required three dimensional data. The overall three dimensional aerodynamic performance of an instrumented classical airfoil cascade was determined over a range of incidence angle values. This was accomplished utilizing a fully automated exit flow data acquisition and analysis system. The mean wake data, acquired at two downstream axial locations, were analyzed to determine the effect of incidence angle, the three dimensionality of the cascade exit flow field, and the similarity of the wake profiles. The hub, mean, and tip chordwise airfoil surface static pressure distributions determined at each incidence angle are correlated with predictions from the MERIDL and TSONIC computer codes.

Bergsten, D. E.↗

NASA NTRS2005

Closed Loop Active Flow Separation Detection and Control in a Multistage Compressor

Active closed loop flow control was successfully demonstrated on a full annulus of stator vanes in a low speed axial compressor. Two independent methods of detecting separated flow conditions on the vane suction surface were developed. The first technique detects changes in static pressure along the vane suction surface, while the second method monitors variation in the potential field of the downstream rotor. Both methods may feasibly be used in future engines employing embedded flow control technology. In response to the detection of separated conditions, injection along the suction surface of each vane was used. Injected mass flow on the suction surface of stator vanes is known to reduce separation and the resulting limitation on static pressure rise due to lowered diffusion in the vane passage. A control algorithm was developed which provided a proportional response of the injected mass flow to the degree of separation, thereby minimizing the performance penalty on the compressor system.

Bright, Michelle M.↗

NASA NTRS1983

Investigation of the tip clearance flow inside and at the exit of a compressor rotor passage. II - Turbulence properties

The flow in the tip clearance region of a compressor rotor is highly turbulent due to the strong interaction of the leakage flow with the annulus wall boundary layer. This paper deals with the turbulence properties of the flow in the tip clearance region of a moderately loaded compressor rotor. The experimental results reported in this paper were obtained using a two-sensor hot-wire probe in combination with an ensemble averaging technique. Blade-to-blade distribution of the axial and tangential turbulence intensities at various radial locations and ten axial locations (four inside the blade passage and the remaining six outside the passage) were derived from this data. Isointensity contours in the clearance region at various radial locations were also obtained from the experimental data. A region of very high turbulence intensities was indicated at the half-chord location from these results. The turbulence intensity profiles also indicated that the leakage flow travels toward the midpassage before rolling up. The turbulence is almost isotropic beyond three-quarter chord downstream of the trailing edge.

Pandya, A.↗

NASA NTRS1994

A Combined Experimental/Computational Study of Flow in Turbine Blade Cooling Passage

Laser velocimetry was utilized to map the velocity field in a serpentine turbine blade cooling passage at Reynolds and Rotation numbers of up to 25.000 and 0.48. These results were used to assess the combined influence of passage curvature and Coriolis force on the secondary velocity field generated. A Navier-Stokes code (NASTAR) was validated against incompressible test data and then used to simulate the effect of buoyancy. The measurements show a net convection from the low pressure surface to high pressure surface. The interaction of the secondary flows induced by the turns and rotation produces swirl at the turns, which persisted beyond 2 hydraulic diameters downstream of the turns. The incompressible flow field predictions agree well with the measured velocities. With radially outward flow, the buoyancy force causes a further increase in velocity on the high pressure surface and a reduction on the low pressure surface. The results were analyzed in relation to the heat transfer measurements of Wagner et al. (1991). Predicted heat transfer is enhanced on the high pressure surfaces and in turns. The incompressible flow simulation underpredicts heat transfer in these locations. Improvements observed in compressible flow simulation indicate that the buoyancy force may be important.

Tse, D. G. N.↗

NASA NTRS1998

The Three Dimensional Flow Field at the Exit of an Axial-Flow Turbine Rotor

A systematic and comprehensive investigation was performed to provide detailed data on the three dimensional viscous flow phenomena downstream of a modem turbine rotor and to understand the flow physics such as origin, nature, development of wakes, secondary flow, and leakage flow. The experiment was carried out in the Axial Flow Turbine Research Facility (AFTRF) at Penn State, with velocity measurements taken with a 3-D LDV System. Two radial traverses at 1% and 10% of chord downstream of the rotor have been performed to identify the three-dimensional flow features at the exit of the rotor blade row. Sufficient spatial resolution was maintained to resolve blade wake, secondary flow, and tip leakage flow. The wake deficit is found to be substantial, especially at 1% of chord downstream of the rotor. At this location, negative axial velocity occurs near the tip, suggesting flow separation in the tip clearance region. Turbulence intensities peak in the wake region, and cross- correlations are mainly associated with the velocity gradient of the wake deficit. The radial velocities, both in the wake and in the endwall region, are found to be substantial. Two counter-rotating secondary flows are identified in the blade passage, with one occupying the half span close to the casino and the other occupying the half span close to the hub. The tip leakage flow is well restricted to 10% immersion from the blade tip. There are strong vorticity distributions associated with these secondary flows and tip leakage flow. The passage averaged data are in good agreement with design values.

Lakshminarayana, B.↗

NASA NTRS1975

Fan noise reduction at subsonic and supersonic tip speeds with high Mach number inlets

Results are presented for an experimental study of two fixed geometry inlets and one translating centerbody type inlet tested in an anechoic-chamber transonic-compressor facility. The test vehicle was a 12-inch tip diameter single-stage transonic compressor with 19 rotor blades and 30 stator blades located approximately two chord lengths downstream of the rotor. It is shown that the translating centerbody type of inlet is superior to the collapsing cowl type for noise reduction at high subsonic Mach numbers, both acoustically and aerodynamically. The feasibility of using a high inlet Mach number depends largely on the maximum area ratio requirement (normally at landing). The high inlet Mach numbers are more effective in reducing high-frequency noise than low frequencies and more effective in reducing the blade passage frequency than the overall noise level.

Lumsdaine, E.↗

NASA NTRS1986

Local heat transfer augmentation in channels with two opposite ribbed surfaces

The local heat transfer coefficient distribution of a square channel with two opposite ribbed walls was determined. The square channel was connected to a sudden contraction entrance in order to simulate the inlet condition of the turbine blade cooling passages. The test channel was heated by thin stainless steel foils with a thickness of 0.000025 m, and instrumented with 180 thermocouples. The brass ribs of a square cross-section were glued periodically, in line, onto the top and bottom walls of the foil-heated channel in patterns to achieve the desired spacing and angle-of-attack. The local heat transfer coefficients on the smooth side and the ribbed side walls, at the channel entrance and the downstream regions, were measured for eight rib configurations and three Reynolds numbers (Re = 10,000, 30,000, and 60,000).

Han, J. C.↗

NASA NTRS1973

Rotating-blade vortex noise

An experimental investigation has been made of the Langley full-scale tunnel and outdoors to investigate some of the characteristics of vortex noise generated on a rotating-blade system. Acoustic measurements were made at several microphone positions for two different blade sections with several tip shapes and spoiler configurations. The blades were operated only at zero lift at each radial station, both for operating in their own wake and for operating with the wake blown downstream. Rotors with cylindrical blades generally created more noise throughout the noise spectrum than the rotor with NACA 0012 blades. Blowing the shed wake from the rotor with cylindrical blades did not have an appreciable effect on the frequency-amplitude spectrum. The tip shape changes had very little effect on the frequency-amplitude spectrum of the noise. Spoilers applied to the rotor with NACA 0012 blades increased the amplitude of the spectrum and decreased the number of harmonics of blade passage frequency.

Scheiman, J.↗

NASA NTRS1999

Inlet Noise Reduction by Shielding for the Blended-Wing-Body Airplane

Noise shielding benefits associated with an advanced unconventional subsonic transport concept, the Blended-Wing-Body, were studied using a 4- percent scale, 3-engine nacelle model. The study was conducted in the Anechoic Noise Research Facility at NASA Langley Research Center. A high- frequency, wideband point source was placed inside the nacelles of the center engine and one of the side engines in order to simulate broadband engine noise. The sound field of the model was measured with a rotating microphone array that was moved to various stations along the model axis and with a fixed array of microphones that was erected behind the model. Ten rotating microphones were traversed a total of 22 degrees in 2-degree increments. Seven fixed microphones covered an arc that extended from a point in the exhaust exit plane of the center engine (and directly below its centerline) to a point 30 degrees above the jet centerline. While no attempt was made to simulate the noise emission characteristics of an aircraft engine, the model source was intended to radiate sound in a frequency range encompassing 1, 2, and 3 times the blade passage of a typical full-scale engine. In this study, the Blended-Wing-Body model was found to provide significant shielding of inlet noise. In particular, noise radiated downward into the forward sector was reduced by 20 to 25 dB overall in the full-scale frequencies from 2000 to 4000 Hz, decreasing to 10 dB or less at the lower frequencies. Also, it was observed that noise associated with the exhaust radiates into the sector directly below the model downstream to reduce shielding efficiency.

Clark, Lorenzo R.↗

NASA NTRS1981

Mean rotor wake characteristics of an aerodynamically loaded 0.5 m diameter fan

Mean rotor wake properties at several downstream distances behind the rotor of a loaded 1.2 pressure ratio fan were measured with a cross film anemometer in an anechoic wind tunnel. Mean wake characteristics in the midspan and near tip region were determined utilizing an ensemble averaging technique. The upwash and streamwise components of the velocity behind the rotor indicate a complex structure superimposed on the major velocity defects at a down stream spacing of 0.5 rotor chords. Spectral analysis indicates high levels of the second and fourth harmonics of the blade passage frequency in the midspan region while the blade passage frequency and its second and third harmonic are predominant in the tip region.

Shaw, L. M.↗

NASA NTRS1987

Effect of possible passage through Halley's magnetic tail on geomagnetic activity

It is found that there occurred a geomagnetic storm on May 18/19, 1910 that cannot be dismissed as a recurrent storm. The period of storminess is close to the period of time at which the magnetic and plasma tail of Halley should have passed over the earth. The signature is worldwide and of the form and magnitude expected if the solar wind were shielded from the earth by the comet. Comparison with computer simulations applicable closer to the comet suggests that this interpretation is feasible. If this interpretation is correct, the 'lobes' of the Halley tail have deeper lows at 24 x 10 to the 6th km than in the present model at 7 x 10 to the 6th km downstream and are at least twice as wide.

Russell, C. T.↗

NASA NTRS1996

Calculation of tip clearance effects in a transonic compressor rotor

The flow through the tip clearance region of a transonic compressor rotor (NASA rotor 37) was computed and compared to aerodynamic probe and laser anemometer data. Tip clearance effects were modeled both by gridding the clearance gap and by using a simple periodicity model across the ungridded gap. The simple model was run with both the full gap height, and with half the gap height to simulate a vena-contracta effect. Comparisons between computed and measured performance maps and downstream profiles were used to validate the models and to assess the effects of gap height on the simple clearance model. Recommendations were made concerning the use of the simple clearance model. Detailed comparisons were made between the gridded clearance gap solution and the laser anemometer data near the tip at two operating points. The computer results agreed fairly well with the data but overpredicted the extent of the casing separation and underpredicted the wake decay rate. The computations were then used to describe the interaction of the tip vortex, the passage shock, and the casing boundary layer.

Chima, R. V.↗

NASA NTRS1998

Calculation of Tip Clearance Effects in a Transonic Compressor Rotor

The flow through the tip clearance region of a transonic compressor rotor (NASA rotor 37) was computed and compared to aerodynamic probe and laser anemometer data. Tip clearance effects were modeled both by gridding the clearance gap and by using a simple periodicity model across the ungridded gap. The simple model was run with both the full gap height, and with half the gap height to simulate a vena-contracta effect. Comparisons between computed and measured performance maps and downstream profiles were used to validate the models and to assess the effects of gap height on the simple clearance model. Recommendations were made concern- ing the use of the simple clearance model Detailed comparisons were made between the gridded clearance gap solution and the laser anemometer data near the tip at two operating points. The computed results agreed fairly well with the data but overpredicted the extent of the casing separation and underpredicted the wake decay rate. The computations were then used to describe the interaction of the tip vortex, the passage shock, and the casing boundary layer.

Chima, R. V.↗

NASA NTRS1985

Three-dimensional inviscid analysis of radial turbine flow and a limited comparison with experimental data

The three-dimensional inviscid DENTON code is used to analyze flow through a radial-inflow turbine rotor. Experimental data from the rotor are compared with analytical results obtained by using the code. The experimental data available for comparison are the radial distributions of circumferentially averaged values of absolute flow angle and total pressure downstream of the rotor exit. The computed rotor-exit flow angles are generally underturned relative to the experimental values, which reflect the boundary-layer separation at the trailing edge and the development of wakes downstream of the rotor. The experimental rotor is designed for a higher-than-optimum work factor of 1.126 resulting in a nonoptimum positive incidence and causing a region of rapid flow adjustment and large velocity gradients. For this experimental rotor, the computed radial distribution of rotor-exit to turbine-inlet total pressure ratios are underpredicted due to the errors in the finite-difference approximations in the regions of rapid flow adjustment, and due to using the relatively coarser grids in the middle of the blade region where the flow passage is highly three-dimensional. Additional results obtained from the three-dimensional inviscid computation are also presented, but without comparison due to the lack of experimental data. These include quasi-secondary velocity vectors on cross-channel surfaces, velocity components on the meridional and blade-to-blade surfaces, and blade surface loading diagrams. Computed results show the evolution of a passage vortex and large streamline deviations from the computational streamwise grid lines. Experience gained from applying the code to a radial turbine geometry is also discussed.

Choo, Y. K.↗

NASA NTRS1985

Three-dimensional inviscid analysis of radial-turbine flow and a limited comparison with experimental data

Choo, Y. K.↗

NASA NTRS2010

Origin of the Central Constant Emission Component of Eta Carinae

The X-ray campaign observation of the wind-wind colliding (WWC) binary system, Eta Carinae, targeted at its periastron passage in 2003, presented a detailed view of the flux and spectral variations of the X-ray minimum phase. One of the discoveries in this campaign was a central constant emission (CCE) component very near the central WWC source (Hamaguchi et al. 2007, ApJ, 663, 522). The CCE component was noticed between 1-3 keY during the X-ray minima and showed no variation on either short timescales within any observation or long timescales of up to ~ 10 years. Hamaguchi et al. (2007) discussed possible origins as collisionally heated shocks from the fast polar winds from Eta Car or the fast moving outflow from the WWC with the ambient gas, or shocked gas that is intrinsic to the wind of Eta Car. During the 2009 periastron passage, we launched another focussed observing campaign of Eta Carinae with the Chandra, XMM-Newton and Suzaku observatories, concentrating on the X-ray faintest phase named the deep X-ray minimum. Thanks to multiple observations during the deep X-ray minimum, we found that the CCE spectrum extended up to 10 keV, indicating presence of hot plasma of kT approx.4-6 keV. This result excludes two possible origins that assume relatively slow winds (v approx. 1000 km/s) and only leaves the possibility that the CCE plasma is wind blown bubble at the WWC downstream. The CCE spectrum in 2009 showed a factor of 2 higher soft band flux as the CCE spectrum in 2003, while the hard band flux was almost unchanged. This variation suggests decrease in absorption column along the line of sight. We compare this result with recent increase in V-band magnitude of Eta Carinae and discuss location of the CCE plasma.

Hamaguchi, Kenji↗

NASA NTRS1991

Numerical prediction of wakes in cascades and compressor rotors including the effects of mixing. II - Rotor passage flow and wakes including the effects of spanwise mixing

The results of a numerical investigation to predict the flow field including wakes and mixing in axial-flow compressor rotors are presented. The wake behavior in a moderately loaded compressor rotor is studied numerically using a 3D incompressible Navier-Stokes solver with a high Reynolds number form of a turbulence model. The equations are solved using a time dependent implicit technique. The agreement between the measured data and the predictions is good; including the blade boundary-layer profiles, wake mean-velocity profiles, and decay. The ability of the pseudocompressibility scheme to predict the entire flow field including the near and far wake profiles and its decay characteristics, effect of loading, and the viscous losses of a 3D rotor flow field are demonstrated. The mixing in the downstream regions away from the hub and annulus walls is dominated by wake diffusion. In regions away from the walls the radial mixing is predominantly caused by the transport of mass, momentum, and energy by the radial component of velocity in the wake.

Lakshminarayana, B.↗

NASA NTRS1982

Observations of Jupiter's distant magnetotail and wake

Results are presented for Voyager 2 plasma wave and plasma measurements, obtained during mid-1980 to August 1981, which indicate the existence of clear signatures of Jovian nonthermal continuum radiation while the spacecraft was in the general downstream direction from Jupiter up to distances of approximately 4.5 AU. A periodicity indicating some solar wind control was indicated by the increasing magnitude and duration of the events as Voyager 2 approached the nominal aberrated tail position in the spring of 1981. It is found that each event shows characteristics suggestive of electromagnetic radiation trapped within a low-density cavity. Several of the events are characterized by a broad, moderately low density region surrounding a well-defined, very low density core. It is concluded that this series of continuum radiation events is best interpreted as the passage of Voyager 2 through the extended magnototail and wake of Jupiter. In addition, the various allowed tail configurations consistent with the observations are examined.

Kurth, W. S.↗