Search NASA⌕ Search

SEARCH · Search NASA

Results for “drag force”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Enhanced mixing of a rectangular supersonic jet by natural and induced screech

The influence of shear layer excitation on the mixing of supersonic rectangular jets was studied experimentally. Two methods of excitation were used to control the jet mixing. The first used the natural screech of an underexpanded supersonic jet from a converging nozzle. The level of the screech excitation was controlled by the use of a pair of baffles located to block the acoustic feedback path between the downstream shock structure and the nozzle lip. A screech level variation of over 30 decibels was achieved and the mixing was completely determined by the level of screech attained at the nozzle lip. The second form of self-excitation used the induced screech caused by obstacles or paddles located in the shear layers on either long side of the rectangular jet. With sufficient immersion of the paddles intense jet mixing occurred and large flapping wave motion was observed using a strobed focused Schlieren system. Each paddle was instrumented with a total pressure tap and strain gages to determine the pressure and drag force on the square cross-section paddle. Considerable drag was observed in this initial exploratory study. Future studies using alternate paddle geometries will be conducted to maximize jet mixing with minimum drag.

Rice, Edward J.↗
NASA NTRS2000

Generation of Bubbly Suspensions in Low Gravity

Generation of a uniform monodisperse bubbly suspension in low gravity is a rather difficult task because bubbles do not detach as easily as on Earth. Under microgravity, the buoyancy force is not present to detach the bubbles as they are formed from the nozzles. One way to detach the bubbles is to establish a detaching force that helps their detachment from the orifice. The drag force, established by flowing a liquid in a cross or co-flow configuration with respect to the nozzle direction, provides this additional force and helps detach the bubbles as they are being formed. This paper is concerned with studying the generation of a bubbly suspension in low gravity in support of a flight definition experiment titled "Behavior of Rapidly Sheared Bubbly Suspension." Generation of a bubbly suspension, composed of 2 and 3 mm diameter bubbles with a standard deviation <10% of the bubble diameter, was identified as one of the most important engineering/science issues associated with the flight definition experiment. This paper summarizes the low gravity experiments that were conducted to explore various ways of making the suspension. Two approaches were investigated. The first was to generate the suspension via a chemical reaction between the continuous and dispersed phases using effervescent material, whereas the second considered the direct injection of air into the continuous phase. The results showed that the reaction method did not produce the desired bubble size distribution compared to the direct injection of bubbles. However, direct injection of air into the continuous phase (aqueous salt solution) resulted in uniform bubble-diameter distribution with acceptable bubble-diameter standard deviation.

Nahra, Henry K.↗
NASA NTRS1988

Spin-up studies of the Space Shuttle Orbiter main gear tire

One of the factors needed to describe the wear behavior of the Space Shuttle Orbiter main gear tires is their behavior during the spin-up process. An experimental investigation of tire spin-up processes was conducted at the NASA Langley Research Center's Aircraft Landing Dynamics Facility. During the investigation, the influence of various parameters such as forward speed and sink speed on tire spin-up forces were evaluated. A mathematical model was developed to estimate drag forces and spin-up times and is presented. The effect of prerotation was explored and is discussed. Also included is a means of determining the sink speed of the orbiter at touchdown based upon the appearance of the rubber deposits left on the runway during spinup.

Daugherty, Robert H.↗
NASA NTRS1973

Neutral winds above 200 km at high latitudes.

Electrically neutral, luminous clouds are a by-product of chemical releases conducted to create barium ion clouds for the measurement of electric fields. Wind measurements provided by the motions of these clouds are particularly valuable in that the motions can be directly compared with convective ion drift motions to test the importance of ion drag forces. Motion from multiple releases between 200 and 300 km from 15 rockets launched from four high-latitude locations is analyzed in this paper. The observations in the evening and midnight hours at magnetic latitudes above 65 deg strongly suggest that in these regions ion drag is the dominant force in driving neutral winds between 200 and 300 km. In the morning sector, it is evident that neutral wind observations cannot be directly interpreted in terms of ion drag; other factors must be considered.

Meriwether, J. W.↗
DOE OSTI2024

Direct numerical simulation of open-channel flow over a heterogeneous particle bed at low relative submergence

In this article, this study investigates turbulent open-channel flows over beds of irregularly arranged particles, using direct numerical simulations at a friction Reynolds number of Re T = 300⁠. Two distinct cases are examined: a polydisperse bed (P800) composed of multiple layers of randomly distributed spheres of varying sizes, and a monodisperse bed (M1015) formed by a random distribution of uniform sized spheres, with a bottommost single layer of varied-sized particles to introduce realistic randomness. Our investigation unveils a rich network of low- and high-speed streaks within the flow field, exhibiting distinctive behaviors in different bed configurations. The P800 case presents a poorly organized flow pattern induced by the varied particle sizes and arrangements, while the M1015 case shows a more regular flow pattern, marked by larger streaks. We also observe that total wall shear stress is substantially influenced by surface roughness-induced drag, extending beyond the effects documented in existing studies of open-channel flows. The present study reveals intricate secondary flow patterns over irregular particle beds. Large-scale circulations are discerned around particle crests in the P800 case and localized circulations with increased turbulence in the M1015 case. Furthermore, analysis of Reynolds stress tensor components indicates that roughness disrupts coherent turbulent eddies, consequently mitigating peak stress. We quantify correlations between drag force and local fluid velocity fluctuations. Notably, a larger deviation in drag is observed in the P800 case compared to M1015, accentuating the influence of particle size and distribution on fluid–particle interactions.

42 ENGINEERING↗
NASA NTRS1990

Wind-tunnel investigation on the effect of a crescent planform on drag

Lift and drag forces were compared for elliptic and crescent wing models at cruise and climb conditions in the NASA/Langley 14 x 22-ft subsonic tunnel. The force measurements were obtained for an angle-of-attack range from -3 to 10 deg at a Reynolds number of about 1.7 million. The results indicate that for attached flow conditions, the crescent wing with its highly swept tips generates less lift-dependent drag than the elliptic wing for given lift force, wing span, and freestream conditions. The drag reduction is thought to be the result of the favorable influence of trailing wake deformations on the pressure distribution of the highly swept outboard region of the crescent wing.

Van Dam, C. P.↗
NASA NTRS2003

Macrovoid Defect Growth during Evaporative Casting of Polymeric Membranes

Macrovoid (MV) formation is a significant problem in evaporatively cast polymeric membranes. MVs are large, elongated or teardrop-shaped pores (~10-50 micron) that can impair membrane structural integrity. Although MVs have been extensively studied, there is no general agreement on the mechanisms governing MV growth. Recently, our research group has formulated the solutocapillary convection (SC) hypothesis, which contends that MV growth involves three principal forces: a Marangoni force generated by surface tension gradients within the MV interface, a viscous drag force, and a gravitationally induced body force. Two sets of complementary experiments were conducted to test the SC hypothesis. Ground-based videomicroscopy flow-visualization (VMFV) was utilized to measure the flow velocities at the MV-casting solution interface and deep within the casting solution. The measurements were performed with casting solutions containing 10 wt% cellulose acetate (CA), 30 wt% H2O, 60 wt% acetone, and 200- ppm TiO2 particles for flow visualization, and the surface tension was controlled by surfactant addition. Qualitatively, the experiments indicated that MV growth occurs in three distinct phases: (1) a very rapid initial growth period, (2) a much slower growth phase, and (3) absorption of selected MVs into the expanding demixed region. The presence of tracer particles inside the MVs suggests the presence of a convective flow, which transfers the particles from the bulk solution to the MV interior. Although the VMFV experiments did not establish any surfactant effect on the interfacial velocities, a statistically significant effect on the MV number density was observed. In the second set of experiments, membranes were cast aboard a KC-135 aircraft under 0-g and 2-g conditions. Despite careful attention to the design and fabrication of the membrane casting apparatus (MCA), several problems were encountered, the most significant of which was the contamination of the casting solution by the activated carbon particles used for solvent absorption.

Greenberg, A. R.↗
DOE OSTI2021

On the temperature and density dependence of dislocation drag from phonon wind

At extreme strain rates, where fast moving dislocations govern plastic deformation, anharmonic phonon scattering imparts a drag force on the dislocations. In this paper, we present calculations of the dislocation drag coefficients of aluminum and copper as functions of temperature and density. We discuss the sensitivity of the drag coefficients to changes in the third-order elastic constants with temperature and density.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Shock interacting with a random array of stationary particles underwater

Accurately predicting the force experienced by particles within a random bed during shock traversal is a challenging problem. In this paper, particle-resolved inviscid simulations of shock propagation over randomly distributed beds are performed, with the goal of quantifying the force on individual particles. Water was considered the continuum material, and then results were compared with previous research completed in air and the differences resulting from these different mediums were examined. Simulations were conducted for four different combinations of incident Mach number and bed volume fraction with the particles remaining stationary. Additionally, time-resolved streamwise and transverse force coefficients were calculated for each particle in the bed. It was observed that while the average force coefficient was similar to that of an isolated particle, the force on individual particles was substantially different. An important observation was that the inviscid drag force on some particles remained consistently positive, but others consistently negative even long after the passage of the shock. This persistent force on the particle was attributed to the potential flow fields that result from neighbors' specific locations upstream and downstream. Similar behavior was observed in the transverse force, with particles experiencing sustained force in the same lateral direction. These persistent forces are inviscid quasisteady contributions which with the viscous counterpart will play an essential role in the particle's long-term dispersion if allowed to move in response to the force.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1923

Preliminary Experiments to Determine Scale and Slip-Stream Effects on a 1/24th Size Model of a JN4H Biplane

This work was undertaken to obtain results on a small model of a complete airplane which might be used for comparison with corresponding tests made in full flight. Somewhat similar tests have been previously made at various other laboratories; but as certain discrepancies exist between corresponding tests in different tunnels, it has been deemed advisable to obtain a direct comparison for this particular installation. The present work covers tests on a one-twenty-fourth scale model at speeds varying from 6.7 m/sec. (15 m.p.h.) to 40.2 m/sec, (90 m.p.h.). A slip stream correction has been obtained by the use of a small belt-driven propeller mounted in front of the model, and force coefficients thus obtained are compared with the measurements of the same forces made in full flight on a geometrically similar airplane. This report gives lift, drag, and longitudinal moment values obtained in tests of a particularly accurate model over a wide range of speeds. A measure of the slip stream corrections on lift and drag forces was obtained by the use of a power-driven model propeller. Measurements were also made of forces and longitudinal moments for all angles from 0 degree to 360 degrees.

Bacon, D L↗
NASA NTRS2017

Spacecraft Re-Entry Impact Point Targeting Using Aerodynamic Drag

The ability to re-enter the atmosphere at a desired location is important for spacecraft containing components that may survive re-entry. While impact point targeting has traditionally been initiated through impulsive burns with chemical thrusters on large vehicles such as the Space Shuttle, and the Soyuz and Apollo capsules, many small spacecraft do not host thrusters and require an alternative means of impact point targeting to ensure that falling debris do not cause harm to persons or property. This paper discusses the use of solely aerodynamic drag force to perform this targeting. It is shown that by deploying and retracting a drag device to vary the ballistic coefficient of the spacecraft, any desired longitude and latitude on the ground can be targeted provided that the maneuvering begins early enough and the latitude is less than the inclination of the orbit. An analytical solution based on perturbations from a numerically propagated trajectory is developed to map the initial state and ballistic coefficient profile of a spacecraft to its impact point. This allows the ballistic coefficient profile necessary to reach a given target point to be rapidly calculated, making it feasible to generate the guidance for the decay trajectory onboard the spacecraft. The ability to target an impact point using aerodynamic drag will enhance the capabilities of small spacecraft and will enable larger space vehicles containing thrusters to save fuel by more effectively leveraging the available aerodynamic drag.

propagation↗
NASA NTRS1924

The effect of wind tunnel turbulence upon the forces measured on models

1. Reasons for inquiry: The tests were undertaken to find the effect of turbulence in the air stream upon the lift and drag forces measured on models in the four-foot wind tunnel at the Massachusetts Institute of Technology. 2. Range of investigation: Maximum lifts and minimum drags were measured on Gottingen-387 and R.A.F.-15 airfoils, minimum drag on a streamlined strut, and the static pressure gradients for different conditions of turbulence. 3. Results and further developments: The results show that the scale of the turbulence (as defined in this report) has a marked effect upon the measured forces on models tested in the tunnel as well as on the pressure gradient, and it is recommended that further investigation of the phenomena be made with the aid of smoke and small wind vanes.

Lepage, W L↗
NASA NTRS1996

Status of MSBS Study at NAL in 1995

Magnetic field intensity and currents passing through the coils of the National Aerospace Laboratory (NAL) 1O cm Magnetic Suspension and Balance System (MSBS) were measured while a cylindrical model was oscillated along x,y,z and also about y and z axes, respectively. The model was made of alnico 5 and was 8 mm in diameter and 60 mm long. Two kinds of tests were carried out. Amplitude of the oscillation was varied at a frequency of 10 Hz. Frequency was varied from 1 to 50 Hz in the other test. Results of the tests show that the relation between coil currents and magnetic force acting on the model is affected by frequency. They also show that the relation between measured magnetic field intensity and the force in vertical direction is independent of the frequency below 30 Hz. Using the measured magnetic field intensity, the vertical force can be evaluated at the MSBS instantaneously when a model moves at frequencies below 30 Hz. A static drag force calibration test was carried out at the 60 cm MSBS. Obtained relationships between measured drag coil currents and loads shows large hysteresis.

Sawada, Hideo↗
NASA NTRS1996

Kuiper Belt Dust Grains as a Source of Interplanetary Dust Particles

The recent discovery of the so-called Kuiper belt objects has prompted the idea that these objects produce dust grains that may contribute significantly to the interplanetary dust population. In this paper, the orbital evolution of dust grains, of diameters 1 to 9 microns, that originate in the region of the Kuiper belt is studied by means of direct numerical integration. Gravitational forces of the Sun and planets, solar radiation pressure, as well as Poynting-Robertson drag and solar wind drag are included. The interactions between charged dust grains and solar magnetic field are not considered in the model. Because of the effects of drag forces, small dust grains will spiral toward the Sun once they are released from their large parent bodies. This motion leads dust grains to pass by planets as well as encounter numerous mean motion resonances associated with planets. Our results show that about 80% of the Kuiper belt grains are ejected from the Solar System by the giant planets, while the remaining 20% of the grains evolve all the way to the Sun. Surprisingly, the latter dust grains have small orbital eccentricities and inclinations when they cross the orbit of the Earth. This makes them behave more like asteroidal than cometary-type dust particles. This also enhances their chances of being captured by the Earth and makes them a possible source of the collected interplanetary dust particles; in particular, they represent a possible source that brings primitive/organic materials from the outer Solar System to the Earth. When collisions with interstellar dust grains are considered, however, Kuiper belt dust grains around 9 microns appear likely to be collisionally shattered before they can evolve toward the inner part of the Solar System. The collision destruction can be applied to Kuiper belt grains up to about 50 microns. Therefore, Kuiper belt dust grains within this range may not be a significant part of the interplanetary dust complex in the inner Solar System.

Liou, Jer-Chyi↗
NASA NTRS1983

The performance of a circulation control airfoil at transonic speeds

A two-dimensional wind tunnel test has been performed on a small circulation control airfoil section equipped with trailing edge blowing. The model was mounted in the NASA-Ames 2 x 2 ft transonic wind tunnel and tested at speeds up to free-stream Mach equals 0.75 for a range of incidences. Jet pressure ratios up to 3 (relative to tunnel static conditions) were evaluated together with the effects of Reynolds number. Normal force and pitching moment coefficients were calculated from surface pressures using a Scanivalve pressure measuring system. Drag force coefficients were calculated from wake rake pressures. The results obtained indicated that this airfoil was capable of producing useful lift at high subsonic Mach numbers. Some changes in the stall characteristics were apparent at above free-stream Mach equals 0.4 and some dependence between lift augmentation and incidence was observed. There also appeared to be a significant Reynolds number effect on the airfoil drag performance.

Wood, N. J.↗
DOE OSTI2023

Compressible pairwise interaction extended point-particle model for force prediction of shock-particle bed interaction

We propose a pairwise influence framework for the complex unsteady compressible particle-laden flow problem by accounting for the scattered hydrodynamic waves emitting from neighboring particles in a Euler-Lagrange simulation. It has been observed from particle-resolved (PR) simulations of randomly dispersed particle beds under a loading shock that the compressible pseudoturbulence dominates the flow system even after the primary shock has passed, which causes fluctuations observed in the forces experienced by the particle. Moreover, the fact that each particle exists in the vicinity of a random arrangement of other particles modifies the time history of the drag force experienced by each particle during and after the passage of the shock. First, the scattering flow field due to an incoming shock interacting with a single sphere is constructed using an analysis of the flow in the acoustic limit. Then we examine the validity of the compressible Maxey-Riley-Gatignol force model by comparing the force prediction against a PR simulation of two interacting particles for various particle arrangements and incoming shock strength. Subsequently, the neighboring influences are stored as a library of maps that can be used readily in the calculation of the perturbation force. Lastly, the pairwise interaction assumption is evaluated by comparing the force predicted with the model with PR simulations of a randomly packed particle bed of 10% volume fraction for both water and air as the fluid medium for an incoming shock Mach number 1.22. With a considerably lower cost for the implementation of the model compared to PR simulations, it is verified that the model is reasonably accurate in pinpointing particles whose peak force is significantly larger or smaller than the mean drag but also to capture the prolonged fluctuations after the initial shock.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1983

Labyrinth seal forces on a whirling rotor

An experimental investigation of air labyrinth seal forces on a subsynchronously whirling model rotor is described and test results are given for diverging, converging, and straight two-strip seals. The effects of pressure drop, provide basic experimental data needed in the development of design methods for predicting and preventing self-excited whirl of turbine rotors and other machines having labyrinth seals. The total dynamic seal forces on the whirling model rotor are measured accurately by means of an active damping and stiffness system that is adjusted to obtain neutral whirl stability of the model rotor system. In addition, the whirling pressure pattern in the seal annulus is measured for a few test conditions and the corresponding pressure forces on the rotor are compared with the total measured forces. This comparison shows that either radial and axial pressure gradients in the seal annulus or drag forces on the rotor are significant. Comparisons made between the measured seal forces and theoretical results show that present theory is inadequate.

Wright, D. V.↗
NASA NTRS1983

Labyrinth seal forces on a whirling rotor

An experimental investigation of air labyrinth seal forces on a subsynchronously whirling model rotor is described and test results are given for diverging, converging, and straight two-strip seals. The effects of pressure drop, back pressure, whirl direction, and whirl frequency are shown. These results provide basic experimental data needed in the development of design methods for predicting and preventing self-excited whirl of turbine rotors and other machines having labyrinth seals. The total dynamic seal forces on the whirling model rotor are measured accurately by means of a novel active damping and stiffness system that is adjusted to obtain neutral whirl stability of the model rotor system. In addition, the whirling pressure pattern in the seal annulus is measured for a few test conditions and the corresponding pressure forces on the rotor are compared with the total measured forces. This comparison shows that either radial and axial pressure gradients in the seal annulus or drag forces on the rotor are significant.

Wright, D. V.↗