SEARCH · Search NASA

Results for “droop”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Study of spectral/radiometric characteristics of the Thematic Mapper for land use applications

The radiometric characteristics of LANDSAT 5 TM data were analyzed. Effects which were found earlier and quantified in LANDSAT 4 TM data were quantified for LANDSAT-5 data as well, including: scan-direction-related signal droop and scan correlated level shifts. Coincident LANDSAT 4 and 5 fully corrected (CCT-PT) TM data were analyzed, and band-by-band relationships between the two sensors were derived in terms of both signal counts and radiance.

Malila, W. A.↗

NASA NTRS1985

Wind-Tunnel Investigation of a Full-Scale Canard-Configured General Aviation Airplane

An investigation was conducted in the Langley 30- by 60-Foot Tunnel to determine the aerodynamic characteristics of a powered, full-scale model of a general aviation airplane employing a canard. Although primary emphasis of the investigation was placed on evaluating the aerodynamic performance and the stability and control characteristics of the basic configuration, tests were also conducted to study the following effects of varying the basic configuration: effect of Reynolds number; effect of canard; effect of outboard wing leading-edge droop; effect of center-of-gravity location; effect of elevator trim; effect of landing gear; effect of lateral-directional control; effect of power; effect of fixed transition; effect of water spray; effects of canard incidence, canard airfoil section, and canard position; and effects of winglets and upper winglet size. Additional aspects of the study were to determine the boundary-layer transition characteristics of airfoil surfaces and the effect of fixing the boundary layer to be turbulent by means of a transition strip near the leading edge. The tests were conducted at Reynolds numbers from 0.60 x 10 to the 6th power to 2.25x10 to the 6th power, based on the wing mean aerodynamic chord, at angles of attack from -4.5 deg to 41.5 deg, and at angles of sideslip from -15 deg to 15 deg.

Yip, L. P.↗

NASA NTRS1983

DC-10 winglet flight evaluation

The results of a flight evaluation of winglets on a DC-10 Series 10 aircraft are presented. For sensitive areas of comparison, effects of winglets were determined back to back with and without winglets. Basic and reduced span winglet configurations were tested. After initial encounter with low speed buffet, a number of acceptable configurations were developed. For maximum drag reduction at both cruise and low speeds, lower winglets were required, having leading edge devices on upper and lower winglets for the latter regime. The cruise benefits were enhanced by adding outboard aileron droop to the reduced span winglet aircraft. Winglets had no significant impact on stall speeds, high speed buffet boundary, and stability and control characteristics. Flutter test results agreed with predictions and ground vibration data. Flight loads measurement also agreed with predictions.

Source record↗

NASA NTRS1985

Characterization and comparison of Landsat-4 and Landsat-5 Thematic Mapper data

Engineering analyses of Thematic Mapper (TM) image data have been conducted, giving particular attention to the radiometric characterization of the sensor. While the data in general were found to be excellent, anomalies do exist in the data from both Landsat-4 and Landsat-5 TM. A summary is provided of the Landsat-4 TM image data. The present paper concentrates, however, on recent analyses of Landsat-5 TM data and comparisons of the radiometry of the two sensors. One of the specific topics covered is within-line droop, a phenomenon whereby the signal levels of the sensor change systematically during the active scan. Attention is also given to scan-correlated level shifts, an effect which raises or lowers the signal level of all pixels in a scan line or set of scan lines. A comparison of Landsat-4 and Landsat-5 radiometric corrections is also discussed.

Metzler, M. D.↗

NASA NTRS1985

Characterization and Comparison of LANDSAT-4 and LANDSAT-5 Thematic Mapper Data

Engineering analyses of Thematic Mapper (TM) image data have been conducted, giving particular attention to the radiometric characterization of the sensor. While the data in general were found to be excellent, anomalies do exist in the data from both LANDSAT-4 and LANDSAT-5 TM. A summary is provided of the LANDSAT-5 TM image data. Recent analyses of LANDSAT-5 TM data and comparisons of the radiometry of the two sensors are emphasized. One of the specific topics covered is within-line droop, a phenomenon whereby the signal levels of the sensor change systematically during the active scan. Attention is also given to scan-correlated level shifts, an effect which raises or lowers the signal level of all pixels in a scan line or set of scan lines. A comparison of LANDSAT-4 and LANDSAT-5 radiometric corrections is also discussed.

Malila, W. A.↗

NASA NTRS1986

An experimental investigation of the structural dynamics of a torsionally soft rotor in vacuum

An extensive data base of structural dynamic characteristics has been generated from an experimental program conducted on a torsionally soft two-bladed model helicopter rotor system. Measurements of vibratory strains for five modes of vibration were made at twenty-one locations on the two blades at speeds varying from 0 to 1000 RPM and for several combinations of precone, droop and flexure stiffness. Tests were conducted in vacuum under carefully controlled conditions using a unique excitation device with a system of piezoelectric crystals bonded to the blade surface near the root. Frequencies, strain mode shapes and dampings are extracted from the time histories and can be used to validate structural dynamics codes. The dynamics of the system are such that there is a clear tendency for the first torsion and second flap modes to couple within the speed range considered. Strain mode shapes vary significantly with speed and configuration. This feature is important in the calcualtion of aeroelastic instabilities. The tension axis tests confirmed that the modulus-weighted centroid for the nonhomogeneous airfoil is slightly off the mass centroid and validated previous static tests done to determine location of the tension axis.

Srinivasan, A. V.↗

NASA NTRS1987

An experimental investigation of the aeromechanical stability of a hingeless rotor in hover and forward flight

Analysis and testing were conducted in the Langley Transonic Dynamics Tunnel to investigate the aeromechanical stability of a soft inplane hingeless rotor model. Rotor stability data were obtained in hover and in forward flight up to an advance ratio of 0.35. Model rotor parameters evaluated were blade sweep and droop, pre-cone of the blade feathering axis, and blade pitch-flap coupling. Data obtained during these tests are presented without analysis.

Yeager, William T., Jr.↗

NASA NTRS1986

Exploratory wind-tunnel investigation of the stability and control characteristics of advanced general aviation configurations

Results of low-speed wind-tunnel investigations are presented for two general aviation configurations: the AVTEK canard configuration and the DeVore conventional configuration. Cooperative research programs were undertaken by industry and NASA to jointly conduct tests in the NASA Langley 12-Foot Low-Speed Wind Tunnel to explore stability and control characteristics of each configuration. A 1/5-scale AVTEK model and a 1/6-scale DeVore model were tested over an angle-of-attack range of up to 45 deg and an angle-of-sideslip range of up to 20 deg. Results from the AVTEK test are presented with an emphasis on the effects of configuration on the stall and poststall characteristics. Results from the DeVore test are presented with emphasis on the effects of wing leading-edge droop design on spin resistance characteristics.

Yip, L. P.↗

NASA NTRS1986

Wind-tunnel investigation of the OMAC canard configuration

Wind-tunnel tests were conducted on a 0.175-scale model of the OMAC Laser 300 canard configuration in the NASA Langley 12-Foot Low-Speed Wind Tunnel to determine its low-speed high angel-of-attack aerodynamic characteristics. The Laser 300 is a general aviation turboprop pusher aircraft utilizing a canard configuration. The design incorporates a low forward wing and a high main wing with a leading-edge droop installed on the outboard panel and tip fins mounted on the wing tips. The model was tested over a range of -6 to 50-deg angle-of-attack and 20 to -20 deg sideslip. Static force and moment data were measured, and the longitudinal and lateral-directional characteristics were determined.

Ingram, W. C.↗

NASA NTRS1987

An experimental study of the aerodynamic characteristics of planar and non-planar outboard wing planforms

A series of wind tunnel experiments have been conducted to investigate the aerodynamic characteristics of several planar and nonplanar wingtip planforms. Seven different configurations: base-line rectangular, elliptical, swept and tapered, swept and tapered with dihedral, swept and tapered with anhedral, rising arc, and drooping arc, were investigated for two different spans. The data are available in terms of coefficient plots of force data, flow visualization photographs, and velocity and pressure flowfield surveys. All planforms, particularly the nonplanar, have some advantages over the baseline rectangular planform. Span efficiencies up to 20-percent greater than baseline are a possibility. However, it is suggested that the span efficiency concept might need refinement for nonplanar wings. Flow survey data show the change in effective span with vortex roll-up. The flow visualization shows the occurrence of mushroom-cell-separation flow patterns at angles of attack corresponding to stall. These grow with an increase in post-stall angle of attack. For the larger aspect ratios, the cells are observed to split into sub-cells at the higher angles of attack. For all angles of attack, some amount of secondary vortex flow is observed for the planar and nonplanar out-board planforms with sweep and taper.

Naik, D. A.↗

NASA NTRS1987

High-angle-of-attack stability and control improvements for the EA-6B Prowler

The factors involved in high-angle-of-attack directional divergence phenomena for the EA-6B ECM aircraft have been investigated in NASA-Langley wind tunnel facilities in order to evaluate airframe modifications which would eliminate or delay such divergence to angles-of-attack farther removed from the operational flight envelope of the aircraft. The results obtained indicate that an adverse sidewash at the aft fuselage and vertical tail location is responsible for the directional stability loss, and that the sidewash is due to a vortex system generated by the fuselage-wing juncture. Modifications encompassing a wing inboard leading edge droop, a wing glove strake, and a vertical fin extension, have significantly alleviated the stability problem.

Jordan, Frank L.↗

NASA NTRS1986

The design of a turboshaft speed governor using modern control techniques

The objectives of this program were: to verify the model of off schedule compressor variable geometry in the T700 turboshaft engine nonlinear model; to evaluate the use of the pseudo-random binary noise (PRBN) technique for obtaining engine frequency response data; and to design a high performance power turbine speed governor using modern control methods. Reduction of T700 engine test data generated at NASA-Lewis indicated that the off schedule variable geometry effects were accurate as modeled. Analysis also showed that the PRBN technique combined with the maximum likelihood model identification method produced a Bode frequency response that was as accurate as the response obtained from standard sinewave testing methods. The frequency response verified the accuracy of linear models consisting of engine partial derivatives and used for design. A power turbine governor was designed using the Linear Quadratic Regulator (LQR) method of full state feedback control. A Kalman filter observer was used to estimate helicopter main rotor blade velocity. Compared to the baseline T700 power turbine speed governor, the LQR governor reduced droop up to 25 percent for a 490 shaft horsepower transient in 0.1 sec simulating a wind gust, and up to 85 percent for a 700 shaft horsepower transient in 0.5 sec simulating a large collective pitch angle transient.

Delosreyes, G.↗

NASA NTRS1986

Preliminary aerodynamic design considerations for advanced laminar flow aircraft configurations

Modern composite manufacturing methods have provided the opportunity for smooth surfaces that can sustain large regions of natural laminar flow (NLF) boundary layer behavior and have stimulated interest in developing advanced NLF airfoils and improved aircraft designs. Some of the preliminary results obtained in exploratory research investigations on advanced aircraft configurations at the NASA Langley Research Center are discussed. Results of the initial studies have shown that the aerodynamic effects of configuration variables such as canard/wing arrangements, airfoils, and pusher-type and tractor-type propeller installations can be particularly significant at high angles of attack. Flow field interactions between aircraft components were shown to produce undesirable aerodynamic effects on a wing behind a heavily loaded canard, and the use of properly designed wing leading-edge modifications, such as a leading-edge droop, offset the undesirable aerodynamic effects by delaying wing stall and providing increased stall/spin resistance with minimum degradation of laminar flow behavior.

Johnson, Joseph L., Jr.↗

NASA NTRS1988

Experimental investigation of non-planar sheared outboard wing planforms

The outboard planforms of wings have been found to be of prime importance in studies of induced drag reduction. This conclusion is based on an experimental and theoretical study of the aerodynamic characteristics of planar and nonplanar outboard wing forms. Six different configurations; baseline rectangular, planar sheared, sheared with dihedral, sheared with anhedral, rising arc, and drooping arc were investigated for two different spans. Span efficiencies as much as 20 percent greater than baseline can be realized with nonplanar wing forms. Optimization studies show that this advantage can be achieved along with a bending moment benefit. Parasite drag and lateral stability estimations were not included in the analysis.

Naik, D. A.↗

NASA NTRS1988

An analysis for high speed propeller-nacelle aerodynamic performance prediction. Volume 1: Theory and application

A computer program, the Propeller Nacelle Aerodynamic Performance Prediction Analysis (PANPER), was developed for the prediction and analysis of the performance and airflow of propeller-nacelle configurations operating over a forward speed range inclusive of high speed flight typical of recent propfan designs. A propeller lifting line, wake program was combined with a compressible, viscous center body interaction program, originally developed for diffusers, to compute the propeller-nacelle flow field, blade loading distribution, propeller performance, and the nacelle forebody pressure and viscous drag distributions. The computer analysis is applicable to single and coaxial counterrotating propellers. The blade geometries can include spanwise variations in sweep, droop, taper, thickness, and airfoil section type. In the coaxial mode of operation the analysis can treat both equal and unequal blade number and rotational speeds on the propeller disks. The nacelle portion of the analysis can treat both free air and tunnel wall configurations including wall bleed. The analysis was applied to many different sets of flight conditions using selected aerodynamic modeling options. The influence of different propeller nacelle-tunnel wall configurations was studied. Comparisons with available test data for both single and coaxial propeller configurations are presented along with a discussion of the results.

Egolf, T. Alan↗

NASA NTRS1989

Transonic aeroelasticity analysis for rotor blades

A numerical method is presented for calculating the unsteady transonic rotor flow with aeroelasticity effects. The blade structural dynamic equations based on beam theory were formulated by FEM and were solved in the time domain, instead of the frequency domain. For different combinations of precone, droop, and pitch, the correlations are very good in the first three flapping modes and the first twisting mode. However, the predicted frequencies are too high for the first lagging mode at high rotational speeds. This new structure code has been coupled into a transonic rotor flow code, TFAR2, to demonstrate the capability of treating elastic blades in transonic rotor flow calculations. The flow fields for a model-scale rotor in both hover and forward flight are calculated. Results show that the blade elasticity significantly affects the flow characteristics in forward flight.

Chow, Chuen-Yen↗

NASA NTRS1989

Experimental investigation of the high angle of attack characteristics of a high performance general aviation aircraft

Scale model wind tunnel tests and full scale flight tests have been conducted for the Questair Venture general aviation aircraft configuration in order to investigate its high angle-of-attack aerodynamics. Attention is given to the formulation of a wing leading-edge modification capable of enhancing stall departure characteristics. This modification, which involved both outboard wing leading-edge droop and two chordwise leading-edge slots, is found to produce almost no wing-rock tendency when tested on a wind tunnel free-to-roll apparatus; in the full-scale aircraft, the modification yielded gentle, controllable stall characteristics with little cruise and climb performance penalty.

Meyer, H. F.↗

NASA NTRS1990

Static Wind-Tunnel and Radio-Controlled Flight Test Investigation of a Remotely Piloted Vehicle Having a Delta Wing Planform

At the request of the United States Marine Corps, an exploratory wind-tunnel and flight test investigation was conducted by the Flight Dynamics Branch at the NASA Langley Research Center to improve the stability, controllability, and general flight characteristics of the Marine Corps Exdrone RPV (Remotely Piloted Vehicle) configuration. Static wind tunnel tests were conducted in the Langley 12 foot Low Speed Wind Tunnel to identify and improve the stability and control characteristics of the vehicle. The wind tunnel test resulted in several configuration modifications which included increased elevator size, increased vertical tail size and tail moment arm, increased rudder size and aileron size, the addition of vertical wing tip fins, and the addition of leading-edge droops on the outboard wing panel to improve stall departure resistance. Flight tests of the modified configuration were conducted at the NASA Plum Tree Test Site to provide a qualitative evaluation of the flight characteristics of the modified configuration.

Yip, Long P.↗