Search NASA⌕ Search

SEARCH · Search NASA

Results for “edge instability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Disturbance-wave interactions in flows with crossflow

The leading-edge region of swept wings is dominated by the crossflow instability, resulting in vortices that all rotate in the same sense. The effect of these possibly unsteady vortices on the behavior of other disturbances is examined, and a strong interaction between these and disturbances of half the dominating crossflow wavelength is predicted. According to theory, the interaction is of crossflow-crossflow type. The effect explains the anomalies found in the experimental observations of Saric and Yeates. Visually, they observe vortices at the wavelength predicted by linear theory; however, in their hot-wire measurements they find that the superharmonic dominates disturbance growth, eventually having three times the amplitude of the primary wave. In this case, the usual transition prediction methods would fail, clearly indicating the importance of studying interactions of this sort.

Reed, H. L.↗
NASA NTRS1985

Combustor flame flashback

A stainless steel, two-dimensional (rectangular), center-dump, premixed-prevaporized combustor with quartz window sidewalls for visual access was designed, built, and used to study flashback. A parametric study revealed that the flashback equivalence ratio decreased slightly as the inlet air temperature increased. It also indicated that the average premixer velocity and premixer wall temperature were not governing parameters of flashback. The steady-state velocity balance concept as the flashback mechanism was not supported. From visual observation several stages of burning were identified. High speed photography verified upstream flame propagation with the leading edge of the flame front near the premixer wall. Combustion instabilities (spontaneous pressure oscillations) were discovered during combustion at the dump plane and during flashback. The pressure oscillation frequency ranged from 40 to 80 Hz. The peak-to-peak amplitude (up to 1.4 psi) increased as the fuel/air equivalence ratio was increased attaining a maximum value just before flashback. The amplitude suddenly decreased when the flame stabilized in the premixer. The pressure oscillations were large enough to cause a local flow reversal. A simple test using ceramic fiber tufts indicated flow reversals existed at the premixer exit during flickering. It is suspected that flashback occurs through the premixer wall boundary layer flow reversal caused by combustion instability. A theoretical analysis of periodic flow in the premixing channel has been made. The theory supports the flow reversal mechanism.

Proctor, M. P.↗
NASA NTRS1987

Wave interactions in swept-wing flows

The leading-edge region of swept wings is dominated by the crossflow instability, resulting in vortices that all rotate in the same sense. The effect of these vortices on the behavior of other disturbances is examined and an interaction between these and disturbances of half the dominating crossflow wavelength is predicted. According to theory, the interaction is of crossflow-crossflow type. The effect explains the anomalies found in the experimental observations of Saric and Yeates (1985). Visually Saric and Yeates observe vortices at the wavelength predicted by linear theory; however, in their hot-wire measurements they find that the second harmonic dominates disturbance growth, with eventually three times the amplitude of the primary wave. In this case, the usual transition-prediction methods would fail, clearly indicating the importance of studying interactions of this sort.

Reed, Helen L.↗
NASA NTRS1992

Laminar flow flight experiments - A review

A development history is presented for flight tests of flow-laminarizing technologies, from the wooden-structure wing glove used with the B-18 of about 1940 to the X-21 of 1963-1965 and the wing incidence-varying tests conducted with gloved-wing F-111 and F-14 variable-sweep aircraft in more recent years. Natural laminar flight control testing has also been conducted with a B 757 airliner. Over the years, increasing attention has been given to the treatment of the leading edge of laminar flow wings in order to prevent flow instabilities that precipitate flow transition to turbulence farther aft.

Wagner, R. D.↗
NASA NTRS1992

Code validation for the simulation of supersonic viscous flow about the F-16XL

The viewgraphs and discussion on code validation for the simulation of supersonic viscous flow about the F-16XL are provided. Because of the large potential gains related to laminar flow on the swept wings of supersonic aircraft, interest in the applications of laminar flow control (LFC) techniques in the supersonic regime has increased. A supersonic laminar flow control (SLFC) technology program is currently underway within NASA. The objective of this program is to develop the data base and design methods that are critical to the development of laminar flow control technology for application to supersonic transport aircraft design. Towards this end, the program integrates computational investigations underway at NASA Ames-Moffett and NASA Langley with flight-test investigations being conducted on the F-16XL at the NASA Ames-Dryden Research Facility in cooperation with Rockwell International. The computational goal at NASA Ames-Moffett is to integrate a thin-layer Reynolds averaged Navier-Stokes flow solver with a stability analysis code. The flow solver would provide boundary layer profiles to the stability analysis code which in turn would predict transition on the F-16XL wing. To utilize the stability analysis codes, reliable boundary layer data is necessary at off-design cases. Previously, much of the prediction of boundary layer transition has been accomplished through the coupling of boundary layer codes with stability theory. However, boundary layer codes may have difficulties at high Reynolds numbers, of the order of 100 million, and with the current complex geometry in question. Therefore, a reliable code which solves the thin-layer Reynolds averaged Navier-Stokes equations is needed. Two objectives are discussed, the first in greater depth. The first objective is method verification, via comparisons of computations with experiment, of the reliability and robustness of the code. To successfully implement LFC techniques to the F-16XL wing, the flow about the leading edge must be maintained as laminar flow. Therefore, the second objective is to focus on a series of numerical simulations with different values of angle of attack, alpha, and Reynolds numbers. The purpose of the simulations is to study their effects on the two main factors which precipitate transition to turbulence at leading edges of highly swept wings (e.g., 'spanwise contamination' and 'crossflow instability').

Flores, Jolen↗
NASA NTRS1997

Structures in Ionospheric Number Density and Velocity Associated with Polar Cap Ionization Patches

Spectral characteristics of polar cap F region irregularities on large density gradients associated with polar ionization patches are studied using in situ measurements made by the Dynamics Explorer 2 (DE 2) spacecraft. The 18 patches studied in this paper were identified by the algorithm introduced by Coley and Heelis, and they were encountered during midnight-noon passes of the spacecraft. Density and velocity spectra associated with these antisunward convecting patches are analyzed in detail. Observations indicate the presence of structure on most patches regardless of the distance between the patch and the cusp where they are believed to develop. Existence of structure on both leading and trailing edges is established when such edges exist. Results, which show no large dependence of Delta N/N power on the sign of the edge gradient del N, do not allow the identification of leading and trailing edges of the patch. The Delta N/N is an increasing function of gradient del N regardless of the sign of the gradient. The correlation between Delta N/N and Delta V is generally poor, but for a given intensity in Delta V, Delta N/N maximizes in regions of large gradients in N. There is evidence for the presence of unstructured patches that seem to co-exist with unstructured horizontal velocities. Slightly smaller spectral indices for trailing edges support the presence of the E X B drift instability. Although this instability is found to be operating in some cases, results suggest that stirring may be a significant contributor to kilometer-size structures in the polar cap.

Kivanc, O.↗
NASA NTRS2010

Two Types of Magnetic Flux Cancellation in the Solar Eruption of 2007 May 20

We study a solar eruption of 2007 May 20, in an effort to understand the cause of the eruption's onset. The event produced a GOES class B6.7 flare peaking at 05:56 UT, while ejecting a surge/filament and producing a coronal mass ejection (CME). We examine several data sets, including H-alpha images from the Solar Optical Telescope (SOT) on Hinode, EUV images from TRACE, and line-of-sight magnetograms from SOHO/MDI. Flux cancelation occurs among two different sets of flux elements inside of the erupting active region: First, for several days prior to eruption, opposite-polarity sunspot groups inside the region move toward each other, leading to the cancelation of approximately 10^{21} Mx of flux over three days. Second, within hours prior to the eruption, positive-polarity moving magnetic features (MMFs) flowing out of the positive-flux spots at approximately 1 kilometer per second repeatedly cancel with field inside a patch of negative-polarity flux located north of the sunspots. The filament erupts as a surge whose base is rooted in the location where the MMF cancelation occurs, while during the eruption that filament flows out along the polarity inversion line between the converging spot groups. We conclude that a plausible scenario is that the converging spot fields brought the magnetic region to the brink of instability, and the MMF cancelation pushed the system "over the edge." triggering the eruption.

Sterlin, Alphonse C.↗
NASA NTRS1996

Simulation of Three-Dimensional Symmetric and Asymmetric Instabilities in Attachment-Line Boundary Layers

On a swept wing, contamination along the leading edge, Tollmien-Schlichting waves, stationary or traveling crossflow vortices, and/or Taylor-Gortler vortices can cause the catastrophic breakdown of laminar to turbulent flow, which leads to increased skin-friction drag for the aircraft. The discussion in this Note will be limited to disturbances which evolve along the attachment line (leading edge of swept wing). If the Reynolds number of the attachment-line boundary layer is greater than some critical value, then the complete wing is inevitably engulfed in turbulent flow. Essentially, there are two critical Reynolds number points that must be considered. The first is for small-amplitude disturbances, and the second is for bypass transition. The present study will use direct numerical simulations to validate a linear 2D-eigenvalue prediction method based on parabolized stability equations by Lin and Malik. This method is considered because it suggests that a number of symmetric and asymmetric modes exist and are stable or unstable on the attachment line depending on the Reynolds number. If validated, the approach would predict a number of modes which are linearly damped in the Reynolds number regime 100 to 245; however, these modes may grow nonlinearly and provide an explanation to this region.

Joslin, Ronald D.↗
NASA NTRS1994

Crossflow instability control on a swept-wing: Preliminary studies

The pressure distribution on a swept wing causes the streamlines at the edge of the boundary layer to be curved. This pressure gradient normal to the external streamline creates a velocity component normal to the external streamline within the boundary layer which is referred to as the crossflow velocity. Because the crossflow velocity profile perpendicular to the wing surface has an inflection point, the profile is unstable. The stationary instability mode takes the form of crossflow vortices. Under these conditions, the boundary layer on the wing is extremely unstable and transition to turbulent flow takes place much closer to the leading edge of the wing than it would on an unswept wing. Higher skin friction drag is associated with turbulent flow, and so better aircraft performance could be obtained if the crossflow could be eliminated One method of controlling crossflow that is being investigated is boundary-layer suction. An extensive airfoil suction experiment in the 8 feet Transonic Pressure Tunnel (TPT) at NASA Langley Research Center will begin late in 1994. Because of the size, complexity, and expense associated with this test, a number of 'risk-reduction' tests are currently being conducted. The 20 x 28 in. Shear Flow Control Tunnel at NASA Langley is being used for some of these tests. Prior to the summer of 1994, a flat plate with a swept leading edge was installed in the 20 x 28 in. tunnel, with a displacement body mounted on the tunnel ceiling that created a pressure distribution on the plate similar to the pressure distribution on a swept wing. The flow over the plate was investigated during the summer of 1994 using a laser Doppler velocimeter (LDV) system. The LDV measurements indicated the possible presence of multiple disturbance modes, a rarely-seen phenomena since, in most tests, one disturbance mode dominates. The possible existence of multiple disturbance modes in the flat plate boundary layer, however, means that the flow in the 20 x 28 in. tunnel is of interest itself, and will be investigated more thoroughly in the future. With a view to these investigations, the boundary layer traverse mechanism in the 20 x 28 in. tunnel was modified to improve its performance, and strain gauges were mounted on the traverse in order to monitor its deflection during a test. Other preliminary work conducted in the 20 x 28 in. tunnel included the use of an infrared camera system. Previous work with this system showed that transition indeed could be detected, but the signal produced by the crossflow vortices was too weak to be detected. It was hoped that spraying the flat plate with naphthalene would augment the heat transfer associated with the crossflow vortices so that they would show up in a IR image; however, experiments showed that this would not work. Another set of tests was conducted in the 20 x 28 in. tunnel to determine the tripping requirements for a set of airfoil-shaped struts that will be used in the 8 feet TPT experiment. Since the Reynolds number associated with these struts is small, a laminar boundary layer would separate early, causing large fluctuations in the flow field. A turbulent boundary layer would remain attached further back, but tripping from laminar to turbulent flow at low Reynolds number is very difficult. However, trip strip configurations were found that should effectively trip the boundary layer at the required conditions. Currently underway is an investigation of the data acquisition requirements for the 8 feet TPT experiment, with the purpose of the finding the minimum amount of data needed to characterize sufficiently the swept-wing boundary layer. This study is being conducted using a numerically generated data set.

Bridges, David H.↗
NASA NTRS1953

Investigation of the Low-Speed Stability and Control Characteristics of a 1/10-Scale Model of the Convair YF-102 Airplane in the Langley Free-Flight Tunnel

An investigation of the low-speed, power-off stability and control characteristics of a 1/10-scale model of the Convair YF-102 airplane has been made in the Langley free-flight tunnel. The model was flown over a lift-coefficient range from 0.5 to the stall in its basic configuration and with several modifications involving leading-edge slats and increases in vertical-tail size. Only relatively low-altitude conditions were simulated and no attempt was made to determine the effect of freeing the controls. The longitudinal stability characteristics of the model were considered satisfactory for all conditions investigated. The lateral stability characteristics were considered satisfactory for the basic configuration over the speed range investigated except near the stall, where large values of static directional instability caused the model to be directionally divergent. The addition of leading-edge slats or an 8-percent increase in vertical-tail area increased the angle of attack at which the model became directionally divergent. The use of leading-edge slats in combination with a 40-percent increase in vertical-tail size eliminated the directional divergence and produced satisfactory stability characteristics through the stall. The longitudinal and lateral control characteristics were generally satisfactory. Although the adverse sideslip characteristics for the model were considered satisfactory over the angle-of-attack range, analysis indicates that the adverse sideslip characteristics of the airplane may be objectionable at high angles of attack.

Johnson, Joseph L., Jr.↗
NASA NTRS1990

Unsteady aerodynamic loading of delta wings for low and high angles of attack

Experimental and theoretical investigations dealing with unsteady flow phenomena are surveyed, with the emphasis on the pattern of vortices which originate from flow separation at sharp leading edges. It is concluded that these vortices exhibit quasi-steady behavior when the alpha-vibrations are such that bursting instability does not occur above the wing surface. A selection of test results from Jarrah (1988) is presented and discussed. For sharp-edged delta models at low speeds, the aerodynamic loads which are plotted quantify the role of parameters AR and K for three ranges of alpha-variation. An extremely approximate and empirical 'theory' is offered, with data on crossflow drag and burst location, to reproduce the behavior of these airloads up to 90 deg. Recent attempts to apply the more sophisticated tools of computational fluid dynamics to the combination of unsteadiness and very high alpha are shown to be deficient.

Ashley, H.↗
NASA NTRS2019

The Intermediate Wake of a Thin Flat Plate with a Circular Trailing Edge

The intermediate wakes of thin flat plates with circular trailing edges (TEs) are investigated here with direct numerical simulations (DNSs). The separating boundary layers are turbulent in all cases. The near wake in two thin-plate cases (IN & NS), with a focus on the vortex shedding process, was explored in a recent article. Intermittent shedding was observed in Case IN. Case NS, with half the TE diameter of Case IN, was an essentially non-shedding case. A third case (ST) with a sharp trailing edge was also investigated and found to exhibit an intermittent wake instability. The objectives of the present study are twofold. The first is to determine if the wake instability found in Case ST exists in Cases IN and NS as well. The second is to provide the distributions of the turbulent normal intensities and shear stress in the wake and to understand these distributions via the budget terms in the corresponding transport equations. The results show that both Cases IN & NS exhibit a wake instability in the intermediate wake region, that is similar to that found earlier in Case ST. We note that in Case IN, the presence of an intermediate-wake instability results in the co-existence of two different types of instability within a single wake. The distributions of the turbulent normal intensities and shear stress, and the budget terms for the streamwise intensity are included and discussed here. All the budget terms contribute appreciably to the overall budget in the transport equation for streamwise normal intensity.

Rai, Man Mohan↗
NASA NTRS1993

Current status of liquid sheet radiator research

Initial research on the external flow, low mass liquid sheet radiator (LSR), has been concentrated on understanding its fluid mechanics. The surface tension forces acting at the edges of the sheet produce a triangular planform for the radiating surface of width, W, and length, L. It has been experimentally verified that (exp L)/W agrees with the theoretical result, L/W = (We/8)exp 1/2, where We is the Weber number. Instability can cause holes to form in regions of large curvature such as where the edge cylinders join the sheet of thickness, tau. The W/tau limit that will cause hole formation with subsequent destruction of the sheet has yet to be reached experimentally. Although experimental measurements of sheet emissivity have not yet been performed because of limited program scope, calculations of the emissivity and sheet lifetime is determined by evaporation losses were made for two silicon based oils; Dow Corning 705 and Me(sub 2). Emissivities greater than 0.75 are calculated for tau greater than or equal to 200 microns for both oils. Lifetimes for Me(sub 2) are much longer than lifetimes for 705. Therefore, Me(sub 2) is the more attractive working fluid for higher temperatures (T greater than or equal to 400 K).

Chubb, Donald L.↗
NASA NTRS1979

On single-degree-of-freedom flutter induced by activated controls

It is shown that activation of the trailing-edge control of an airfoil leads to single-degree-of-freedom type instabilities which span over a very wide region of reduced frequencies k, including high values of k (unlike the nonactivated system). These instabilities are shown to be sensitive to changes in pitching axis location, control deflection phase angle, and values of the reduced frequency. These sensitivities of the single-degree-of-freedom system cause the activated airfoil to be potentially sensitive to changes in flight conditions, and may be the source of the many difficulties encountered in suppressing classical multi-degree-of-freedom flutter by means of active controls. The results presented herein relate to zero Mach number and to a 20% trailing-edge control surface.

Nissim, E.↗
NASA NTRS2018

Generation of Electron Whistler Waves at the Mirror Mode Magnetic Holes: MMS Observations and PIC Simulation

The Magnetospheric Multiscale mission has observed electron whistler waves at the center and at the edges of magnetic holes in the dayside magnetosheath. The magnetic holes are nonlinear mirror structures since their magnitude is anticorrelated with particle density. In this article, we examine the growth mechanisms of these whistler waves and their interaction with the host magnetic hole. In the observations, as magnetic holes develop and get deeper, an electron population gets trapped and develops a temperature anisotropy favorable for whistler waves to be generated. In addition, the decrease in magnetic field magnitude and the increase in density reduce the electron resonance energy, which promotes the electron cyclotron resonance. To investigate this process, we used expanding box particle-in-cell simulations to produce the mirror instability, which then evolve into magnetic holes. The simulation shows that whistler waves can be generated at the center and edges of magnetic holes, which reproduces the primary features of the MMS observations. The simulation shows that the electron temperature anisotropy develops in the center of the magnetic hole once the mirror instability reaches its nonlinear stage of evolution. The plasma is then unstable to whistler waves at the minimum of the magnetic field structures. In the saturation regime of mirror instability, when magnetic holes are developed, the electron temperature anisotropy appears at the edges of the holes and electron distributions become more isotropic at the magnetic field minimum. At the edges, the expansion of magnetic holes decelerates the electrons, which leads to temperature anisotropies.

Magnetospheric Multiscale↗
NASA NTRS1994

Gravitational instabilities in protostellar disks

The nonaxisymmetric stability of self-gravitating, geometrically thick accretion disks has been studied for protostellar systems having a wide range of disk-to-central object mass ratios. Global eigenmodes with four distinctly different characters were identified using numerical, nonlinear hydrodynamic techniques. The mode that appears most likely to arise in normal star formation settings, however, resembles the 'eccentric instability' that was identified earlier in thin, nearly Keplerian disks: It presents an open, one-armed spiral pattern that sweeps continuously in a trailing direction through more than 2-pi radians, smoothly connecting the inner and outer edges of the disk, and requires cooperative motion of the point mass for effective amplification. This particular instability promotes the development of a single, self-gravitating clump of material in orbit about the point mass, so its routine appearance in our simulations supports the conjecture that the eccentric instability provides a primary route to the formation of short-period binaries in protostellar systems.

Tohline, J. E.↗
NASA NTRS1994

The FU Orionis Outburst as a Thermal Disk Accretion Event: Detailed Calculations and Comparison to Observations

FU Orionis outbursts are temporary large increases in luminosity: x(40-250) thought to occur repeatedly in all low mass young stellar systems. We discuss detailed calculations of viscous accretion disks suggesting that FU Ori events signify the existence of a protostellar disk transporting mass at a rate of (1-10) x 10(exp -6) Solar Mass/yr, in agreement with theoretical and observational estimates of molecular cloud core collapse rates. Accretion through the inner edge of disks subject to outburst is self-regulated through the thermal ionization instability such that long periods (approximately 1000 yrs) of low mass flux: (1-10) x 10(exp -8) Solar Mass/yr, are punctuated by short periods (approximately 100 yrs) of high mass flux: (1-10) x 10(exp -5) Solar Mass/yr. The unstable region of the disk extends radially only to a distance of approximately 1/4 AU. Beyond this region matter is transported stably at the infall rate. In systems for which M = 1 Solar Mass, with an inner disk edge of 3 Solar Radius, the critical rate for outbursts is 5 x 10(exp -7) Solar Mass/yr independent of the magnitude of the viscous alpha parameter consistent with estimates of boundary layer mass flux in T Tauri stars. We use timescales of observed outbursts to constrain the magnitude of the alpha parameter to be 10(exp -4) where hydrogen is neutral and 10(exp -3) where ionized. Light curves of V1515 Cyg, FU Ori, and V1057 Cyg are reproduced; the latter two require application of a small perturbation in surface density to produce observed rapid rise times. Detailed reply is made to objections to the accretion disk model for outbursts. Comparison to observations are made of time dependent spectral energy distributions, colors, and line-width velocity evolution.

Bell, K. R.↗
NASA NTRS2021

Kozai–Lidov Oscillations Triggered by a Tilt Instability of Detached Circumplanetary Discs

Circumplanetary discs can be linearly unstable to the growth of disc tilt in the tidal potential of the star–planet system. We use3D hydrodynamical simulations to characterize the disc conditions needed for instability, together with its long-term evolution.Tilt growth occurs for disc aspect ratios, evaluated near the disc outer edge, ofH/r0.05, with a weak dependence on viscosityin the wave-like regime of warp propagation. Lower mass giant planets are more likely to have circumplanetary discs thatsatisfy the conditions for instability. We show that the tilt instability can excite the inclination to above the threshold where thecircumplanetary disc becomes unstable to Kozai–Lidov (KL) oscillations. Dissipation in the KL unstable regime caps furthertilt growth, but the disc experiences large oscillations in both inclination and eccentricity. Planetary accretion occurs in episodicaccretion events. We discuss implications of the joint tilt–KL instability for the detectability of circumplanetary discs, for theobliquity evolution of forming giant planets, and for the formation of satellite systems.

Rebecca G Martin↗