Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrode preparation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

All-Solid-State Batteries Using Rationally Designed Garnet Electrolyte Frameworks

Functioning bulk-type all-solid-state batteries in a practical form factor with composite positive electrodes, using Al-substituted Li 7 La 3 Zr 2 O 12 (LLZO) as the solid electrolyte, have been demonstrated for the first time. The devices incorporate bilayers composed of dense LLZO membranes and porous LLZO scaffolds infiltrated with LiNi 0.6 Mn 0.2 Co 0.2 O 2 and other components as positive electrodes, combined with lithium anodes. The porous scaffolds are prepared using an easily scaled freeze-tape-casting method. The unidirectional pores of the scaffold facilitate infiltration of cathode components and shorten lithium ion diffusion path lengths, while the addition of a soft ionically conductive solid to the scaffold ensures good contact among the components.

25 ENERGY STORAGE↗
DOE OSTI2022

Bridge Sites of Au Surfaces Are Active for Electrocatalytic CO 2 Reduction

Prior in-situ attenuated total reflectance Fourier transform infrared (ATR-FTIR) studies of electrochemical CO 2 reduction catalyzed by Au, one of the most selective and active electrocatalysts to produce CO from CO 2 , suggest that the reaction proceeds solely on the top sites of the Au surface. This finding is worth updating with an improved spectroelectrochemical system where in-situ IR measurements can be performed under real reaction conditions that yield high CO selectivity. Herein, we report the preparation of a Au-coated Si ATR crystal electrode with both high catalytic activity for CO 2 reduction and strong surface enhancement of IR signals validated in the same spectroelectrochemical cell, which allows us to probe the adsorption and desorption behavior of bridge-bonded *CO species (*CO B ). In this study we find that the Au surface restructures irreversibly to give an increased number of bridge sites for CO adsorption within the initial tens of seconds of CO 2 reduction. By studying the potential-dependent desorption kinetics of *CO B and quantifying the steady-state surface concentration of *CO B under reaction conditions, we further show that *CO B are active reaction intermediates for CO 2 reduction to CO on the Au surface. At medium overpotential, as high as 38% of the reaction occurs on the bridge sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Lithium battery electrodes

Electrode materials for electrochemical cells and batteries and methods of producing such materials are disclosed herein. The electrode materials comprise an active lithium metal oxide material prepared by: (a) contacting the lithium metal oxide material with an aqueous acidic solution containing one or more metal cations; and (b) heating the so-contacted lithium metal oxide from step (a) to dryness at a temperature below 200° C. The metal cations in the aqueous acidic solution comprise one or more metal cations selected from the group consisting of an alkaline earth metal ion, a transition metal ion, and a main group metal ion.

25 ENERGY STORAGE↗
DOE OSTI2022

The Synthesis of Manganese Hydroxide Nanowire Arrays for a High-Performance Zinc-Ion Battery

The morphology, microstructure as well as the orientation of cathodic materials are the key issues when preparing high-performance aqueous zinc-ion batteries (ZIBs). In this paper, binder-free electrode Mn(OH)2 nanowire arrays were facilely synthesized via electrodeposition. The nanowires were aligned vertically on a carbon cloth. The as-prepared Mn(OH)2 nanowire arrays were used as cathode to fabricate rechargeable ZIBs. The vertically aligned configuration is beneficial to electron transport and the free space between the nanowires can provide more ion-diffusion pathways. As a result, Mn(OH)2 nanowire arrays yield a high specific capacitance of 146.3 Ma h g−1 at a current density of 0.5 A g−1. They also demonstrates ultra-high diffusion coefficients of 4.5 × 10−8~1.0 × 10−9 cm2 s−1 during charging and 1.0 × 10−9~2.7 × 10−11 cm−2 s−1 during discharging processes, which are one or two orders of magnitude higher than what is reported in the studies. Furthermore, the rechargeable Zn//Mn(OH)2 battery presents a good capacity retention of 61.1% of the initial value after 400 cycles. This study opens a new avenue to boost the electrochemical kinetics for high-performance aqueous ZIBs.

25 ENERGY STORAGE↗
DOE OSTI2026

Mass spectral molecular mapping shows benefits of thermal evaporation in prelithiated silicon-based electrodes

Silicon based composites have become increasingly popular as potential anodes for lithium-ion batteries due to their large storage capacity and potential ability to generate batteries with energy densities greater than 350 Wh kg −1 . These anodes often see reduced initial columbic efficiency (ICE) due to disruptive volume expansionup to 300% and continuous solid electrolyte interphase (SEI) layer formation. Prelithiation, where an excess reservoir of Li is added to the electrode to compensate for irreversible SEI formation losses during their sample preparation, has proven to solve the issue of immediate capacity loss. Thermal evaporation is a prelithiation technique with limited studies on its effectiveness. In this study, time-of-flight secondary ion mass spectrometry (ToF-SIMS) is used to highlight the benefits of prelithiation via thermal evaporation. ToF-SIMS provides chemical mapping and spatial information in 2D and 3D visualizing the deposition of lithium, identifying Li x Si y alloy and Li x Si y O z silicate formation, and the distribution of lithium passivation into the electrodes. Passivation under different atmospheric conditions, such as inert Argon (Ar) and Ar/ carbon dioxide (CO 2 ), highlights the impact of the environment on the passivation effectiveness and formation of Li x Si y alloy and Li x Si y O z silicate. The ToF-SIMS molecular imaging and depth profiling results indicate that prelithiation via thermal evaporation effectively distributes lithium throughout the depth profile thickness of several hundred nanometers. It induces a greater degree of Li x Si y O z silicate formation over Li x Si y alloy. Our ToF-SIMS characterization results show the effectiveness of thermal evaporation in producing a more stable electrode and an electrode with an effective lithium reserve that can preserve its capacity.

Parker, Gabriel D. [Oak Ridge National Laboratory ↗
DOE OSTI2023

Biopolymer‐assisted Synthesis of P‐doped TiO 2 Nanoparticles for High‐performance Lithium‐ion Batteries: A Comprehensive Study

Abstract TiO 2 material has gained significant attention for large‐scale energy storage due to its abundant, low‐cost, and environmentally friendly properties, as well as the availability of various nanostructures. Phosphorus doping has been established as an effective technique for improving electronic conductivity and managing the slow ionic diffusion kinetics of TiO 2 . In this study, non‐doped and phosphorus doped TiO 2 materials were synthesized using sodium alginate biopolymer as chelating agent. The prepared materials were evaluated as anode materials for lithium‐ion batteries (LIBs). The electrodes exhibit remarkable electrochemical performance, including a high reversible capacity of 235 mAh g −1 at 0.1 C and excellent first coulombic efficiency of 99 %. An integrated approach, combining operando XRD and ex‐situ XAS, comprehensively investigates the relationship between phosphorus doping, material structure, and electrochemical performance, reinforced by analytical tools and first principles calculations. Furthermore, a full cell was designed using 2 %P‐doped TiO 2 anode and LiFePO 4 cathode. The output voltage was about 1.6 V with high initial specific capacity of 148 mAh g −1 , high rate‐capability of 120 mAh g −1 at 1 C, and high‐capacity retention of 96 % after 1000 cycles at 1 C.

El Halya, Nabil↗
DOE OSTI2020

Combined Experimental and Theoretical Investigations of n-Type BiFeO 3 for Use as a Photoanode in a Photoelectrochemical Cell

Combined experimental and theoretical investigations were performed to evaluate the potential of n-type BiFeO 3 as a photoanode. While previous experimental and theoretical studies on BiFeO 3 mainly focused on its ferroelectric properties, several studies have reported the advantages of BiFeO 3 as a photoelectrode for solar water splitting (e.g. bandgap energy and band edge positions relative to water reduction and oxidation potentials). However, the photoelectrochemical properties of n-type BiFeO 3 have not yet been thoroughly investigated. In our experimental investigation, we developed an electrodeposition-based synthesis to prepare uniform n-type BiFeO 3 thin-film electrodes. Furthermore, using a heat treatment under a N 2 environment, we intentionally introduced additional oxygen vacancies into the pristine n-type BiFeO 3 electrodes to increase the majority carrier density. The bandgaps, flatband potentials, photocurrent onset potentials, photocurrent generation, and photoelectrochemical stabilities of the pristine and N 2 -treated BiFeO 3 photoanodes were investigated comparatively to improve our understanding of BiFeO 3 photoanodes and to examine the effect of oxygen vacancies on the photoelectrochemical properties of BiFeO 3 . In our theoretical investigation, we performed first-principles calculations and demonstrated the formation of a small polaron when an extra electron was introduced into the BiFeO 3 lattice. Changes in electronic states cause by the small polaron formation were carefully investigated. We also examined the effects of oxygen vacancies on electron polaron formation and carrier concentration in BiFeO 3 . Using charge formation energy calculations and referencing charge transition levels to the free electron polaron level instead of to the conduction band minimum, we showed that the oxygen vacancy is capable of serving as a donor to enhance the carrier concentration of BiFeO 3 . Furthermore, our theoretical results agree well with our experimental findings. Together, the new experimental and theoretical results and discussion provided in this study have considerably improved our understanding of n-type BiFeO 3 as a photoanode.

25 ENERGY STORAGE↗
DOE OSTI2020

Roll-To-Roll Atomic Layer Deposition of Titania Nanocoating on Thermally Stabilizing Lithium Nickel Cobalt Manganese Oxide Cathodes for Lithium Ion Batteries

Conformal coating of ceramic layers (nm-thick) on Ni-rich layered cathode materials is an effective strategy for improving high-temperature longevity of Li-ion batteries (LIBs). In this work, we develop a roll-to-roll atomic layer deposition (R2R ALD) apparatus for growing uniform nanolayers of TiO 2 . We explore the effect of ALD parameters (temperature: 120–180 °C and line speed: 2–40 mm s –1 ) on the TiO 2 surface coating and subsequently investigate the electrochemical performance of the as-prepared cathodes. The capacity retention of TiO 2 -coated porous electrodes is substantially improved compared to that of the pristine cathode material for high-temperature cycling. Electrochemical impedance spectroscopy confirms that the ALD-TiO 2 coating suppresses the undesired side reactions initiated at the electrode/electrolyte interface, reduces charge transfer resistance, and ultimately facilitates the Li + transport through the composite cathode nanostructure. The robust design of the ALD-TiO 2 cathode material enables high-temperature operation (>55 °C) with enhanced specific capacity, superior rate capability, excellent cyclability, and ultra-high coulombic efficiency within a wide potential window (3.0–4.35 V). Furthermore, the R2R ALD technique developed in this work paves the way for large-scale fabrication of ceramic-coated cathode sheets with a production rate reaching 2.4 m min –1 for a continuous coating operation.

25 ENERGY STORAGE↗
DOE OSTI2021

Selective Chloride-Mediated Neat Ethanol Oxidation to 1,1-Diethoxyethane via an Electrochemically Generated Ethyl Hypochlorite Intermediate

Selective primary alcohol oxidation to form aldehydes products without overoxidation to carboxylic acids remains a key chemistry challenge. Using simple alkylammonium chloride as the electrolyte with a glassy carbon working electrode in neat ethanol solvent, 1,1-diethoxyethane (DEE) was prepared with >95% faradaic efficiency (FE). DEE serves as a storage platform protecting acetaldehyde from overoxidation and volatilization. UV–vis spectroscopy shows that the reaction proceeds through an ethyl hypochlorite intermediate as the sole chloride oxidation product, and that this intermediate decomposes unimolecularly (rate constant k = (6.896 ± 0.516) × 10 –4 s –1 ) to form HCl catalyst and acetaldehyde, which undergoes rapid nucleophilic attack by ethanol solvent to form the DEE product. As a result, this indirect oxidation mechanism enables ethanol oxidation at much less positive potentials due to the fast kinetics for chloride anion oxidation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Long-Term Stability Metrics of Photoelectrochemical Water Splitting

Photoelectrochemical (PEC) water splitting, one of the most promising technologies for clean hydrogen generation, has drawn considerable attention over the past few decades. Achieving simultaneous highly efficient and stable unassisted PEC water splitting has been the “holy grail” in clean and renewable fuel generation. State-of-the-art photoelectrodes have shown relatively high efficiencies (∼10–20%). Still, their stability is limited due to photoelectrode chemical instability, electrolyte resistance, mass transfer issues, and an often unoptimized experimental setup. In this work, we present a framework and a set of protocols for conducting long-term stability experiments and further provide details on several critical factors such as light source calibration, choosing the right counter electrode, the configuration of the PEC cell, and photoelectrode sample preparation.

08 HYDROGEN↗
DOE OSTI2024

Fuel Cell Membrane Electrode Assemblies with Ultra-Low Pt Nanofiber Electrodes (Final Report)

H 2 /air fuel cell membrane-electrode-assemblies (MEAs) were fabricated with electrospun particle/polymer nanofiber mat cathodes (0.1 mg Pt /cm 2 or 0.2 mg Pt /cm 2 Pt/C, PtCo/C or PtNi/C) and anodes (0.1 mg/cm 2 Pt/C), where the binder was a mixture of acid-form perfluorosulfonic acid ionomer (e.g., Nafion™) and poly(acrylic acid) (PAA) carrier polymer or sodium-form PFSA with a carrier polymer of either PAA or polyethylene oxide (PEO). For the latter two cases, the water-soluble carrier was removed from the fibers after electrospinning. MEAs with Pt/C anode/cathode catalyst loadings of 0.1 mg Pt /cm2 each, an 1100 EW PFSA binder (Nafion™ dispersion), and a Nafion 211 membrane produced high power at both high and low relative humidity (RH) conditions, e.g., a maximum power density of 919 mW/cm 2 at 100% RH and 832 mW/cm 2 at 40% RH for a test at 80 °C and 200 kPa abs . The high power at low RH was attributed to nm-size pores within the fibers that trap water via capillary condensation thus maintaining a high proton conductivity of the PFSA binder in the cathode and especially the anode while minimizing/eliminating ionic isolation of catalyst particles in low water content, poorly conductive binder. At the same time, micro-porosity between fibers in the cathode allows for fast removal of electrogenerated water, thus minimizing cathode flooding. Nanofiber MEAs with Pt alloy catalyst cathodes also performed well, where a fibrous PtCo/C catalyst cathode at a loading of 0.1 mg/cm 2 produced 20% more power than a conventional powder cathode MEA, e.g., a maximum power density of 1,045 mW/cm 2 vs. 869 mW/cm 2 at 80 °C, 100% RH, and 200 kPa abs , and a PtNi/C fiber cathode MEAs prepared with Na+-form Nafion + PEO generated a maximum power of 820 mW/cm 2 at 40% RH. Fiber electrode MEAs with a neat Nafion binder (prepared from Na+-form Nafion + PEO or PAA) where the cathode Pt loading was ~0.1 mg/cm 2 exhibited a 25% loss in maximum power at 30,000 metal dissolution cycles, as compared to a 12% loss when the cathode binder was H+-form Nafion + PAA. The performance of a fiber mat electrode MEA with Pt/C catalyst (0.2 mg/cm 2 cathode loading and 0.1 mg/cm 2 anode loading) was excellent. At 80 oC and 200 kPa abs , the maximum power density was 1104 mW/cm 2 . The maximum power was independent of feed gas humidity for 40 < RH < 100%. The power loss after a metal dissolution AST (30,000 voltage cycles) was only 13%.

08 HYDROGEN↗
DOE OSTI2022

Vertically assembled nanosheet networks for high-density thick battery electrodes

As one of the prevailing energy storage systems, lithium-ion batteries (LIBs) have become an essential pillar in electric vehicles (EVs) during the past decade, contributing significantly to a carbon-neutral future. However, the complete transition to electric vehicles requires LIBs with yet higher energy and power densities. Here, we propose an effective methodology via controlled nanosheet self-assembly to prepare low-tortuosity yet high-density and high-toughness thick electrodes. By introducing a delicate densification in a three-dimensionally interconnected nanosheet network to maintain its vertical architecture, facile electron and ion transports are enabled despite their high packing density. This dense and thick electrode is capable of delivering a high volumetric capacity >1,600 mAh cm −3 , with an areal capacity up to 32 mAh cm −2 , which is among the best reported in the literature. The high-performance electrodes with superior mechanical and electrochemical properties demonstrated in this work provide a potentially universal methodology in designing advanced battery electrodes with versatile anisotropic properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Impact of Catalyst Ink Dispersing Solvent on PEM Fuel Cell Performance and Durability

The dispersing solvent used for fuel cell catalyst ink preparation plays a vital role in establishing the resulting morphology of the electrode layers, which in turn will impact the performance of proton exchange membrane (PEM) fuel cells. In this study, we report the impact of various ionomer dispersion solvents on PEM fuel cell performance and durability; two aqueous (1-propanol/water and 2-propanol/water) and several non-aqueous dispersing solvents (ethylene glycol and 1,2-butanediol) are compared. The cathode catalyst layer (CCL) fabricated using inks prepared with 1-propanol/water (3:1, w/w) exhibited the best initial performance followed by the CCL prepared using ethylene glycol. The CCLs made from non-aqueous ethylene glycol and 1,2-butanediol exhibited the best durability upon accelerated stress testing. Scanning transmission electron microscopy combined with energy dispersive X-ray spectroscopy indicated that, after the stress test, the distribution of both the Nafion ionomer and Pt nanoparticles within the CCLs prepared with non-aqueous ionomer dispersions underwent less change than those prepared with aqueous dispersions, which is responsible for the improved durability

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Influence of Annealing Temperature on the OER Activity of NiO(111) Nanosheets Prepared via Microwave and Solvothermal Synthesis Approaches

Earth-abundant transition metal oxides are promising alternatives to precious metal oxides as electrocatalysts for the oxygen evolution reaction (OER) and are intensively investigated for alkaline water electrolysis. OER electrocatalysis, like most other catalytic reactions, is surface-initiated, and the catalyst performance is fundamentally determined by the surface properties. Most transition metal oxide catalysts show OER activities that depend on the predominantly exposed crystal facets/surface structure. Therefore, the design of synthetic strategies to obtain the most active crystal facets is of significant research interest. In this work, rock salt NiO OER catalysts with (111) predominantly exposed facets were synthesized by a solvothermal (ST) method either heated under supercritical or microwave-assisted (MW) conditions. Particular emphasis was placed on the influence of the post annealing temperature on the structural configuration and OER activity to compare their catalytic performances. The as-prepared electrocatalysts are pure α-Ni hydroxides which were converted to rock salt NiO (111) nanosheets with hexagonal pores after heat treatment at different temperatures. The OER activity of the electrodes has been evaluated in 0.1 M KOH using geometric and intrinsic current densities via normalization by the disk area and BET area, respectively. The lowest overpotential at a geometric current density of 10 mA/cm 2 is found for samples pretreated by heating between 400 and 500 °C with a catalyst loading of 115 μg/cm 2 . Despite the very similar nature of the catalysts obtained from the two methods, the ST electrodes show a higher geometric and intrinsic current density for 500 °C pretreatment. The MW electrodes, however, achieve an optimal geometric current density for 400 °C pretreatment, while their intrinsic current density requires pretreatment over 600 °C. Interestingly, pretreated electrodes show consistently higher OER activity as compared to the poorly crystalline/less ordered hydroxide as-prepared electrocatalysts. Thus, our study highlights the importance of the synthesis method and pretreatment at an optimal temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Examining Performance Loss Mechanisms in Lithium-Ion Batteries with the High-Voltage Mn-Rich Spinel Positive Electrodes

The high-voltage spinel, with the nominal composition of LiNi 0.5-x Mn 1.5+x O 4 (LNMO), could be a sustainable alternative to the layered-oxide positive electrodes used in lithium-ion batteries. However, commercial acceptance has been limited as LNMO cells display rapid performance loss during cycling. To examine reasons for this loss we prepared cells with LNMO-based positive and either graphite or lithium titanate (LTO) based negative electrodes. Our initial cells displayed high impedance and rapid impedance rise during cycling. Adding single walled carbon nanotubes in the positive lowered initial cell impedance but impedance increased during cycling because of coating delamination from the Al foil. Using a primed Al current collector solved the delamination problem: cells with this current collector showed only a small impedance rise. Regarding capacity, cells with the LTO negative showed higher initial capacities and smaller fade. Our data indicate that cell capacity retention is determined by reduction reactions at the negative electrode that lower capacity and oxidation reactions at the positive electrode that increase capacity: both types of reactions deplete the cell electrolyte during extended cycling. All things considered, species generated at high voltages, either in the electrolyte or at the LNMO electrode, drive cell capacity fade.

25 ENERGY STORAGE↗
DOE OSTI2022

Binder-Free Wood Converted Carbon for Enhanced Water Desalination Performance

Here, the design and synthesis of high-performance and economical carbon electrodes play a critical role in developing energy-efficient water desalination technologies. As a sustainable approach, low-cost and abundant biomass materials are promising candidates to prepare porous carbon for capacitive deionization. In this study, binder-free porous carbon sheets are successfully prepared using natural balsa, pine, and basswood by thermal carbonization and treated by chemical activation. The carbon electrode materials converted from balsa and pine exhibit a comparable salt adsorption performance by capacitive deionization due to the extensive surface area, substantial electrical property, and superior hydrophilic performance. The following activation treatment of the balsa-converted carbon further enhances the surface and electrical properties and benefits the desalination performance. The salt adsorption capacity of the activated balsa electrode exhibits 12.45 mg g -1 . Additionally, 19.52 mg g -1 Pb 2+ and 20.06 mg g -1 Cr 3+ heavy metal adsorption capacity is also observed with the activated balsa electrode in 100 mg L -1 PbCl 2 and 50 mg L -1 CrCl 3 , respectively. To the best of authors’ knowledge, this is the highest NaCl adsorption capacity performance reported thus far by using pure wood converted carbon as the electrode, and these promising results indicate that activated balsa is an extraordinary material for water desalination.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Corn stover‐derived porous carbon for asymmetric supercapacitors

In this investigation, hydrothermal liquefaction‐derived hydrochar from pulverized corn stover (avg. particle size 1.12 mm and ash content 6.75 wt%) is chemically activated with aqueous KOH in the presence of Pluronic F127 surfactant and thermally treated further up to 800°C to generate porous carbon (POC) with higher specific surface area and porosity. POC obtained under different processing conditions is thoroughly characterized by Brunauer‐Emmett‐Teller surface area analyzer, Fourier transform infrared spectroscopy, Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy. Metallic impurity present in POC is characterized by inductively coupled plasma mass spectrometry. Higher specific surface area POC is observed with the use of the surfactant during the activation process. Fully characterized POC is used with (Mn, Ti)‐mixed oxide electrode to fabricate asymmetric supercapacitor (ASC). Specific capacitance of ASC is measured by cyclic voltammetry (CV) technique using Gamry G‐300 potentiostat/galvanostat/ZRA. CV plots are obtained with different voltage scan rates whereas galvanostatic charge‐discharge plots are studied by varying the current density. Renewable corn stover‐derived POC prepared using Pluronic F127/KOH activation method is found to be highly suitable as an electrode material because of higher capacitance and electrochemical stability over 100 charging‐discharging cycles.

25 ENERGY STORAGE↗
DOE OSTI2021

Role of Polysulfide Anions in Solid-Electrolyte Interphase Formation at the Lithium Metal Surface in Li–S Batteries

Delineating intricate interactions between highly reactive Li-metal electrodes and the diverse constituents of battery electrolytes has been a long-standing scientific challenge in materials design for advanced energy storage devices. Here, we isolated lithium polysulfide anions (LiS 4 - ) from an electrolyte solution based on their mass-to-charge ratio and deposited them on Li-metal electrodes under clean vacuum conditions using ion soft landing (ISL), a highly controlled interface preparation technique. The molecular level precision in the construction of these model interfaces with ISL, coupled with in situ x-ray photoelectron spectroscopy and ab initio theoretical calculations, allowed us to obtain unprecedented insight into the parasitic reactions of well-defined polysulfides on Li-metal electrodes. Our study reveals that the oxide-rich surface layer, which is amenable to direct electron exchange, drives multielectron sulfur oxidation (S o → S 6+ ) processes. Furthermore, our results have substantial implications for the rational design of future Li-S batteries with improved efficiency and durability.

25 ENERGY STORAGE↗