Search NASA⌕ Search

SEARCH · Search NASA

Results for “elevated temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Elevated temperature slow plastic deformation of NiAl-TiB2 particulate composites at 1200 and 1300 K

Elevated temperature compression testing has been conducted in air at 1200 and 1300 K with strain rates varying from about 10 to the -4th to about 10 to the -7th/sec on NiAl-TiB2 particulate composites. These materials, which consisted of a B2 crystal structure intermetallic Ni-50 at. pct Al matrix and from 0 to 30 vol pct of approximately 1- micron diameter TiB2 particles, were fabricated by XD synthesis and hot pressed to full density. Flow strength of the composites increased with volume fraction of the strengthening phase with NiAl-30TiB2 being approximately three times stronger than NiAl. Comparison of the light optical and TEM microstructures of as-received and tested samples revealed that reactions did not occur between the two phases, and NiAl-TiB2 interfaces were not cracked during deformation. Additional TEM indicated that the particles stabilize a vastly different microstructure in the NiAl matrix of the composites than that formed in unreinforced NiAl.

Whittenberger, J. Daniel↗
NASA NTRS1959

Theoretical Determination of Lifetime of Compressed Plates at Elevated Temperatures

A method for the theoretical determination of the lifetime of com- pressed plates at elevated temperatures is presented. In this approach, linearized equations are used throughout with the assumption that the plate material is a standard linear solid. The critical time (lifetime) is determined by reducing the time-dependent behavior to the time- independent response of purely elastic buckling. Theoretically predicted lifetimes of 2024-T3 (formerly 24S-T3) aluminum-alloy plates at 450 F are compared with experimental values obtained in previous work.

Herrmann, George↗
NASA NTRS1983

Influence of thermomechanical processing on elevated temperature slow plastic flow properties of B2 aluminide Fe-39.8at.% Al

A study of the elevated temperature slow plastic flow properties of the B2 aluminide Fe-39.8at.% Al was undertaken. Polycrystalline materials possessing several different microstructures were produced by the hot extrusion of prealloyed powder and, in some cases, postextrusion heat treatments. Compression tests were conducted in air at 1200, 1300 and 1400 K. Such testing revealed that the extrusion temperature affected the active deformation mechanisms where material extruded at 1505 K had a stress exponent about twice that of the intermetallic extruded at 1200 K. Grain size refinement to about 10 microns was found to strengthen the Fe-39.8at.% Al material; unfortunately, the effectiveness of such strengthening is limited to a homologous temperature of about 0.75 for strain rates of commercial interest (less than 10 to the -7th/sec).

Whittenberger, J. D.↗
NASA NTRS1972

Feasibility demonstration of a hyperfiltration technique to reclaim shower wastewater at elevated temperatures

A feasibility demonstration of a hyperfiltration technique to determine its capability to reclaim shower wastewater at elevated temperature was conducted. Approximately twenty (20) gallons of typical shower water were processed through a dynamically formed membrane at a temperature of 167 F. Chemical and bacterial analyses of the product water are presented which show compliance with all potable water requirements established for extended manned space missions. In addition, subsystem characteristics and capabilities are discussed.

Hester, J. C.↗
NASA NTRS1992

Fatigue and flexural response of advanced carbon-carbon composites at room and elevated temperatures

The flexural response of SiC-coated carbon-carbon composites (ACC-4) at room and elevated temperatures is presented. Three-point bending tests were performed on virgin and mission-cycled specimens, and the variation in flexural strength is examined. The load-deflection behavior of the material at various temperatures is investigated, and the Weibull (1939) analysis of the strength data is performed. Micrographs of various cross sections in the damaged zone were taken, and the failure mechanisms are discussed. Fatigue tests were conducted under flexural loads, and the S-N diagram with the corresponding Weibull analysis are presented. Untested as well as fractured specimens under static and dynamic loading were C-scanned to identify the damaged zone and visualize the extent of the damage. Failure analyses are presented for both static and cyclic loading on the basis of NDE, the micrographs, and the experimental data.

Mahfuz, Hassan↗
NASA NTRS1960

An Evaluation of Some Current Practices for Short-Time Elevated-Temperature Tensile Tests of Metals

The effect of different testing practices on the short-time elevated-temperature tensile properties was determined for 2024-T3 aluminum-alloy, HM21A-T8 and HK31A-H24 magnesium-alloy, and 12 MoV stainless-steel sheet. Tests were made under single strain-rate and single head-speed conditions. A dual strain-rate test was also included. An evaluation of the effects of these practices is given for the tensile and yield strengths, the elongation in 2 inches, and the uniform elongation. The need for a uniform testing practice is demonstrated. Recommended practices suggested by different organizations are included.

Manning, Charles R., Jr.↗
NASA NTRS1985

Infrared spectroscopic studies of the effect of elevated temperature on the association of pyroglutamic acid with clay and other minerals

Fourier transform i.r. measurements of L-pyroglutamic acid dispersed in a matrix of a clay, silica or alumina have been obtained at various temperatures between 25 and 220 degrees C. The i.r. spectrum of L-pyroglutamic acid varies in a manner dependent upon the matrix material and shows considerable change as the temperature of the mixtures is increased. The differences in the spectrum at elevated temperatures are explained in terms of a chemical reaction between hydroxyl groups in the matrix and the carboxylic acid. The i.r. spectra of trimethylsilyl derivatives of L-pyroglutamic acid and aluminum pyroglutamate were also measured to assist the understanding of spectra and interpretation of the spectral changes dependent upon increasing temperature.

Aluminum Oxide/analysis/chemistry↗
NASA NTRS1966

Tantalum alloys resist creep deformation at elevated temperatures

Dispersion-strengthened tantalum-base alloys possess high strength and good resistance to creep deformation at elevated temperatures in high vacuum environments. They also have ease of fabrication, good weldability, and corrosion resistance to molten alkali metals.

Buckman, R. W., Jr.↗
NASA NTRS1983

A study of the effect of apparent strain on thermal stress measurement for two types of elevated temperature strain gages

A weldable type strain gage was used to measure low level thermal stress in an elevated temperature environment. Foil strain gages used in a comparative manner reveal that the apparent strain of weldable strain gages is not sufficiently known to acquire accurate low level thermal stress data. Apparent strain data acquired from coupon tests reveals a large scatter in apparent strain characteristics among the weldable strain gages. It is concluded that apparent strain data for individual weldable strain gages must be required prior to installation if valid thermal stress data is to be obtained through the temperature range of room temperature to 755 K (900 F).

Jenkins, J. M.↗
NASA NTRS1979

Applications of the IITRI compression test fixture at elevated temperature

The purpose of the present paper is to describe an application of the IITRI compression test fixture at elevated temperature (589K) was described as well as the present compressive moduli and ultimate strains of HTS/PMR-15 graphite/polyimide material. Considerable care was taken in specimen fabrication to minimize back-to-back strain variations due to specimen bending. The effects of specimen width and temperature were studied for various laminate orientations. The IITRI specimen was analyzed using three dimensional finite elements to determine the magnitude and location of stress concentrations to assess their potential effects on measured moduli and ultimate strains. Stress concentrations are of concern since end constraints, free-edge effects, and thermal effects add to the three dimensional nature of stresses in a specimen.

Camarda, C. J.↗