Search NASA⌕ Search

SEARCH · Search NASA

Results for “elevated temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

In situ study on heavy ion irradiation induced microstructure evolution in single crystal Cu with nanovoids at elevated temperature

Understanding the response of nanovoids to irradiation damage advances our capability to design radiation tolerant materials. Recent in situ studies reveal the shrinkage of hexagon-shaped nanovoids in (110) textured Cu. However, the evolution of voids with irregular geometries under irradiation is less well understood. Here, in situ Kr ion irradiation was performed at 100 °C on single-crystal Cu (112) that possesses nanovoids with high aspect ratio. In situ studies show these elongated voids fragment into smaller voids and shrink gradually with increasing dose. Phase field simulations confirm that fragmentation of the void is governed by the competing kinetics between atoms diffusing toward and away from the elongated nanovoid. In conclusion, cost irradiation analysis reveals the formation of high-density defect clusters.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2025

Corrosion analysis of Al-Ce-Ni and Al-Cu-Ce cast alloys in dilute boric acid at room and elevated temperatures

Two Al-Ce-Ni cast alloys, and an Al-Cu-Ce cast alloy, as candidate wet storage materials for spent nuclear fuels, were tested in 0.23 wt% H 3 BO 3 solution to assess the alloy corrosion resistance. Electrochemical and gravimetric corrosion data suggest that the three Al alloys are unlikely to undergo any severe corrosion in dilute H 3 BO 3 at or below 50 °C. Post-exposure characterization of the three Al alloys, including scanning and transmission electron microscopy and electron dispersive spectroscopy, revealed a corrosion product layer, mostly Al 2 O 3 , on the exposed surface and local penetration of oxygen into the alloy matrix. The degree of oxide layer growth and oxygen penetration is greater at 80 °C than the temperature at/below 50 °C. The Al-Cu-Ce alloy is considered less corrosion resistant than the other two alloys studied.

Al-Ce alloy↗
DOE OSTI2023

Behavior and properties of helium cavities in ductile-phase-toughened tungsten irradiated with He + ions at an elevated temperature

Ductile-phase toughened tungsten (DPT W) composites have demonstrated a great potential for plasma-facing components in fusion power systems. These materials can retain the outstanding thermomechanical properties of W while significantly enhancing the fracture toughness. The DPT W composite in this study consists of W particles (88 wt.%) embedded in a ductile NiFeW (12 wt.%) solution matrix. Irradiation of the composite was performed with 90 keV He + ions to 1.0 × 10 17 He + /cm 2 at 973 K. The He cavities formed in both W and NiFeW phases are examined using convergent-beam scanning transmission electron microscopy (CB-STEM) at an atomic-level resolution. Full-range depth profiles of the He cavity diameters and number densities are analyzed. The results show that the average cavity diameter in NiFeW is ~2.7 times that in W, while the number density is an order of magnitude lower. A quantitative analysis of the He density and pressure in the cavities is also achieved using STEM electron energy loss spectroscopy (STEM-EELS) mapping. The He atoms in the cavities in NiFeW are found to be under-pressurized, while those in similar-sized cavities in W are not detectable. Further, the He energy-loss shift exhibits a linear relationship with the He density in cavities in NiFeW, with the slope comparable to that for martensitic steel.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Interfacial engineering for stabilizing polymer electrolytes with 4V cathodes in lithium metal batteries at elevated temperature

Poly (ethylene oxide) (PEO) polymer electrolytes are promising candidates for next-generation rechargeable lithium batteries. However, the poor interfacial stability between 4 V cathodes and PEO electrolytes impedes their applications in 4 V lithium batteries with high energy density. Here, we demonstrate a facile and effective strategy to enhance the interfacial stability by the synergy of Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) coating on the cathode surface, and salt combination in the electrolyte, even with a cut-off voltage of 4.25–4.4 V vs. Li + /Li. Nano-LAGP coated Li|PEO|LiCoO 2 cell delivers stable cycling with a capacity retention of 81.9%/400 cycles and 84.7%/200 cycles at 60 °C when charged to 4.25 and 4.3 V in pure polyether electrolyte, respectively. Steady cycling is also demonstrated at room temperature and with LiNi 0.5 Co 0.2 Mn 0.3 O 2 (NCM523) cathode. This work offers a viable and scalable approach to improve the stability between PEO electrolytes and 4 V cathodes and open up new possibilities for practical application of 4 V lithium metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Tribochemical changes of alloy 800HT under sliding contact at elevated temperature in impure helium environment

This work investigates the chemical changes of the surface of Alloy 800HT during sliding contact under helium atmosphere in the presence of impurities at 750 °C, which is of interest for the nuclear industry. The alloy samples are exposed to helium (He) atmosphere at high temperature for long duration of 500 h to identify the chemical and topographical changes of the alloy surface. The oxidation rate constant is reported based on the weight change data. For the tribo-experimental samples, the surfaces inside and outside the wear track are studied thoroughly using techniques such as secondary electron microscopy, energy dispersive spectroscopy, x-ray diffraction, Raman spectroscopy and secondary ion mass spectroscopy. The formation and evolution of surface oxides are discussed in He atmosphere, compared with air. The presence of Fe-rich thin layer of oxide on top of a thicker Cr-rich oxide and a mixed spinel-based inner layer on the bulk is found. The persistent presence of thicker Fe3O4 in the wear track in high temperature air proved to be the reason of lower friction property. Pre-oxidation of the samples in air or He does not improve but worsen the tribological behavior in He atmosphere.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Electronic Structure and Safety Insights into Prussian Blue Analog Cathode Behavior at Elevated Temperatures in Sodium-Ion Batteries

Prussian blue analogs (PBAs) represent promising cathode materials for sodium-ion batteries (SIBs) due to their high theoretical capacity, open framework structure, and use of earth-abundant elements. However, the high-temperature structural evolution, water content effects, and thermal safety of PBAs, particularly in charged states, remain poorly understood, hindering their practical deployment. Here, we investigate Na 2 Fe[Fe(CN) 6 ]·2H 2 O using thermogravimetric analysis (TGA), ex situ and in situ temperature-dependent X-ray absorption spectroscopy (XAS), and accelerated rate calorimetry (ARC). TGA and ex situ XAS confirm water loss between 150 and 200 °C, resulting in Fe 2+ oxidation, enhanced local symmetry, and uniform redox behavior that improves electrochemical performance. In situ XAS reveals irreversible structural changes above 240 °C, including ligand loss, Fe site distortion, and increased disorder, while ARC on charged electrodes shows minimal self-heating rates (<0.1 °C/min) up to 300 °C, indicating exceptional thermal stability without lattice oxygen release. These insights elucidate PBA thermal dynamics, demonstrating improved electrochemical performance of water-deficient PBAs and informing future material design and safety assessment for SIB applications.

batteries↗
DOE OSTI2025

Rational Electrolyte Design for Elevated-Temperature and Thermally Stable Lithium-Ion Batteries with Nickel-Rich Cathodes

As the energy density of lithium-ion batteries (LIBs) increases, the shortened cycle life and the increased safety hazard of LIBs are drawing increasing concerns. To address such challenges, a series of localized high-concentration electrolytes (LHCEs) based on a solvating-solvent mixture of tetramethylene sulfone and trimethyl phosphate and a high flash-point diluent 1H,1H,5H-octafluoropentyl 1,1,2,2-tetrafluoroethyl ether were designed. The LHCEs exhibited non-flammability and greatly suppressed heat release at high temperatures, which would potentially improve the safety performance of the LIBs. Moreover, the optimal LHCE achieved capacity retentions of 87.1% and 81.7% in graphite||LiNi 0.8 Mn 0.1 Co 0.1 O 2 cells after 500 cycles at 25 °C and 45 °C, respectively, which were significantly better than the conventional electrolyte, whose capacity retentions were only 75.2% and 38.5% under the same condition. Mechanistic studies revealed that the LHCE not only formed a more robust solid electrolyte interphase, but also exhibited improved anodic stability, compared with the conventional electrolyte. Further, this work sheds light in rational electrolyte design for high energy density LIBs with high battery performance and low safety concerns.

25 ENERGY STORAGE↗
DOE OSTI2024

Alkali cation stabilization of defects in 2D MXenes at ambient and elevated temperatures

Transition metal carbides have been adopted in energy storage, conversion, and extreme environment applications. Advancements in their 2D counterparts, known as MXenes, enable the design of unique structures at the ~1 nm thickness scale. Alkali cations have been essential in MXenes manufacturing processing, storage, and applications, however, exact interactions of these cations with MXenes are not fully understood. In this study, using Ti 3 C 2 T x , Mo 2 TiC 2 T x , and Mo 2 Ti 2 C 3 T x MXenes, we present how transition metal vacancy sites are occupied by alkali cations, and their effect on MXene structure stabilization to control MXene’s phase transition. We examine this behavior using in situ high-temperature x-ray diffraction and scanning transmission electron microscopy, ex situ techniques such as atomic-layer resolution secondary ion mass spectrometry, and density functional theory simulations. In MXenes, this represents an advance in fundamentals of cation interactions on their 2D basal planes for MXenes stabilization and applications. Broadly, this study demonstrates a potential new tool for ideal phase-property relationships of ceramics at the atomic scale.

42 ENGINEERING↗
DOE OSTI2021

NaCl aggregation in water at elevated temperatures and pressures: Comparison of classical force fields

The properties of water vary dramatically with temperature and density. This can be exploited to control its effectiveness as a solvent. Thus, supercritical water is of keen interest as solvent in many extraction processes. The low solubility of salts in lower density supercritical water has even been suggested as a means of desalination. The high temperatures and pressures required to reach supercritical conditions can present experimental challenges during collection of required physical property and phase equilibria data, especially in salt-containing systems. Molecular simulations have the potential to be a valuable tool for examining the behavior of solvated ions at these high temperatures and pressures. However, the accuracy of classical force fields under these conditions is unclear. We have, therefore, undertaken a parametric study of NaCl in water, comparing several salt and water models at 200 bar–600 bar and 450 K–750 K for a range of salt concentrations. We report a comparison of structural properties including ion aggregation, hydrogen bonding, density, and static dielectric constants. All of the force fields qualitatively reproduce the trends in the liquid phase density. An increase in ion aggregation with decreasing density holds true for all of the force fields. The propensity to aggregate is primarily determined by the salt force field rather than the water force field. This coincides with a decrease in the water static dielectric constant and reduced charge screening. While a decrease in the static dielectric constant with increasing NaCl concentration is consistent across all model combinations, the salt force fields that exhibit more ionic aggregation yield a slightly smaller dielectric decrement.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

A semi-analytical model for laser induced densification in fused silica at elevated temperatures

A semi-analytical model for deterministic surface smoothing of fused silica below the evaporation temperature threshold is presented. Using this model, a method for calculating deterministic track depths for laser polishing fused silica is derived and validated with experiments. In this work, model predictions were in good agreement with experiment across varying laser preheating temperature and power. With the semi-analytical method presented here, deterministic laser smoothing can be achieved in the densification regime to close the process loop of laser polishing.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Schottky contacts to N-polar GaN with SiN interlayer for elevated temperature operation

In this Letter, we unveil the high-temperature limits of N-polar GaN Schottky contacts enhanced by a low-pressure chemical vapor deposited (LPCVD) SiN interlayer. Compared to conventional Schottky diodes, the insertion of a 5 nm SiN lossy dielectric interlayer in-between Ni and N-polar GaN increases the turn-on voltage (V ON ) from 0.4 to 0.9 V and the barrier height ($\phi_B$) from 0.4 to 0.8 eV. This modification also reduces the leakage current at zero bias significantly: at room temperature, the leakage current in the conventional Schottky diode is >103 larger than that observed in the device with the SiN interlayer, while at 200 °C, this ratio increases to 105. Thus, the rectification ratio (ION/IOFF) at ±1.5 V reduces to less than one at 250 °C for the conventional Schottky diode, whereas for SiN-coated diodes, rectification continues until 500 °C. The I–V characteristics of the diode with an SiN interlayer can be recovered after exposure to 400 °C or lower. Contact degradation occurs at 500 °C, although devices are not destroyed yet. Here, we report N-polar GaN Schottky contact operation up to 500 °C using an LPCVD SiN interlayer.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗