Search NASA⌕ Search

SEARCH · Search NASA

Results for “etch”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Effect of crystal orientation on anisotropic etching and MOCVD growth of grooves on GaAs

Grooves can be formed on GaAs by wet-chemical anisotropic etching of surfaces masked by photoresist stripes. The effect of crystal orientation on the shape of the grooves etched and on subsequent epitaxial growth by MOCVD is presented. The polar lattice increases the complexity of the etching and growth processes. The slow-etch planes defined by anisotropic etching are not always the same as the growth facets produced during MOCVD deposition, especially for deposition on higher order planes.

Bailey, Sheila G.↗
NASA NTRS1992

Plasma etching a ceramic composite

Plasma etching is found to be a superior metallographic technique for evaluating the microstructure of a ceramic matrix composite. The ceramic composite studied is composed of silicon carbide whiskers (SiC(sub W)) in a matrix of silicon nitride (Si3N4), glass, and pores. All four constituents are important in evaluating the microstructure of the composite. Conventionally prepared samples, both as-polished or polished and etched with molten salt, do not allow all four constituents to be observed in one specimen. As-polished specimens allow examination of the glass phase and porosity, while molten salt etching reveals the Si3N4 grain size by removing the glass phase. However, the latter obscures the porosity. Neither technique allows the SiC(sub W) to be distinguished from the Si3N4. Plasma etching with CF4 + 4 percent O2 selectively attacks the Si3N4 grains, leaving SiC(sub W) and glass in relief, while not disturbing the pores. An artifact of the plasma etching reaction is the deposition of a thin layer of carbon on Si3N4, allowing Si3N4 grains to be distinguished from SiC(sub W) by back scattered electron imaging.

Hull, David R.↗
NASA NTRS1993

Investigation of etching techniques for superconductive Nb/Al-Al2O3/Nb fabrication processes

Wet etching, CF4 and SF6 reactive ion etching (RIE), RIE/wet hybrid etching, Cl-based RIE, ion milling, and liftoff techniques have been investigated for use in superconductive Nb/Al-Al2O3/Nb fabrication processes. High-quality superconductor-insulator-superconductor (SIS) junctions have been fabricated using a variety of these etching methods; however, each technique offers distinct tradeoffs for a given process an wafer design. In particular, it was shown that SF6 provides an excellent RIE chemistry for low-voltage anisotropic etching of Nb with high selectivity to Al. The SF6 tool has greatly improved the trilevel resist junction insulation process. Excellent repeatability, selectivity with respect to quartz, and submicron resolution make Cl2 + BCl3 + CHCl3 RIE a very attractive process for trilayer patterning.

Lichtenberger, A. W.↗
NASA NTRS1998

Gaseous Etching for Characterization of Structural Defects in Silicon Carbide Single Crystals

Single crystal SiC substrates were subjected to high-temperature H2/C3H8 gaseous etches. The etches resulted in a variety of surface features on 4H-SiC substrates that included elongated hillocks from 10 to more than 100 microns in length by a few microns in width. In some 4H- and 6H-SiC substrates, the etches resulted in a continuous coverage of macrosteps. We conclude that the morphology observed after the etching process is influenced by the local Si-C bilayer stacking sequence on the surface of off-(0001)oriented substrates. A model is presented for the formation of the hillocks, based on localized transformations of the 4H substrates during the high temperature etch process.

Powell, J. A.↗
NASA NTRS1999

Innovative, Inexpensive Etching Technique Developed for Polymer Electro- Optical Structures

Electro-optic, polymer-based integrated optic devices for high-speed communication and computing applications offer potentially significant advantages over conventional inorganic electro-optic crystals. One key area of integrated optical technology--primary processing and fabrication--may particularly benefit from the use of polymer materials. However, as efforts concentrate on the miniaturization of electro-integrated circuit pattern geometries, the ability to etch fine features and smoothly sloped sidewalls is essential to make polymers useful for electro-integrated circuit applications. There are many existing processes available to etch polymer materials, but they all yield nearly vertical sidewalls. Vertical sidewalls are too difficult to reliably cover with a metal layer, and incomplete metalization degrades microwave performance, particularly at high frequency. However, obtaining a very sloped sidewall greatly improves the deposition of metal on the sidewall, leading to low-loss characteristics, which are essential to integrating these devices in highspeed electro-optic modulators. The NASA Lewis Research Center has developed in-house an inexpensive etching technique that uses a photolithography method followed by a simple, wet chemical etching process to etch through polymer layers. In addition to being simpler and inexpensive, this process can be used to fabricate smoothly sloped sidewalls by using a commercial none rodible mask: Spin-On-Glass. A commercial transparent material, Spin-On-Glass, uses processes and equipment similar to that for photoresist techniques.

Nguyen, Hung D.↗
DOE OSTI2020

Deep photoenhanced wet material etching using high-power ultraviolet light emitting diodes

Methods and systems for etching a substrate using photoenhanced wet etching techniques are described. At least one light emitting diode source is used to create a high intensity of ultraviolet light at the surface of the substrate or at one or more layers formed on the substrate. Etching rates in GaN substrates and GaN layers are improved by an order of magnitude over conventional systems. Systems and methods for forming a device structure free of a substrate are described. The device structure is grown or applied over a release layer on a substrate. The device structure is exposed to photoenhanced wet etch environments to vertically and laterally etch the release layer to separate the device structure from the substrate.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Autonomous hybrid optimization of a SiO 2 plasma etching mechanism

Computational modeling of plasma etching processes at the feature scale relevant to the fabrication of nanometer semiconductor devices is critically dependent on the reaction mechanism representing the physical processes occurring between plasma produced reactant fluxes and the surface, reaction probabilities, yields, rate coefficients, and threshold energies that characterize these processes. The increasing complexity of the structures being fabricated, new materials, and novel gas mixtures increase the complexity of the reaction mechanism used in feature scale models and increase the difficulty in developing the fundamental data required for the mechanism. This challenge is further exacerbated by the fact that acquiring these fundamental data through more complex computational models or experiments is often limited by cost, technical complexity, or inadequate models. In this paper, we discuss a method to automate the selection of fundamental data in a reduced reaction mechanism for feature scale plasma etching of SiO 2 using a fluorocarbon gas mixture by matching predictions of etch profiles to experimental data using a gradient descent (GD)/Nelder–Mead (NM) method hybrid optimization scheme. These methods produce a reaction mechanism that replicates the experimental training data as well as experimental data using related but different etch processes.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Bis[2-(methacryloyloxy)ethyl] phosphate radiografted into track-etched PVDF for uranium (VI) determination by means of cathodic stripping voltammetry

Here, we report the radiation grafting of bis[2-(methacryloyloxy)ethyl] phosphate (B2MP) through electron-beam onto PVDF films and through swift heavy ions (SHI) irradiations into the pores of track-etched PVDF membranes. Radiolytically produced radicals were studied using EPR. To adapt the radiation grafting protocol inside the nanopores of track-etched membranes, the electron-beam irradiated films at varying monomer concentrations, doses and solvent mixtures were first studied. It was found that track-etched membranes, even after 1 h of chemical treatment, do not require a post-etching irradiation to initiate free-radical polymerization of B2MP from remaining radiationinduced radicals. The presence of functional groups inside the nanopores of the membrane were examined using FTIR and XPS. After exposure of B2MP-g-PVDF membranes to a uranyl solution, XPS was also exploited to evidence of O 2 UO 2 2+ trapping inside the membrane nanoporosity by tracking the presence of U 4f peak. The B2MP-g-PVDF membranes were converted into electrodes by depositing 35 nm of gold on each side through a mask. Detection of ppb concentrations (from 20 to 100 ppb) of uranyl by B2MP-g-PVDF membrane electrodes was demonstrated by means of square wave cathodic stripping voltammetry (SW-CSV). The limit of detection (LOD) was estimated to be 17 ppb (3σ–/ slope).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Scalable and Resilient Etched Metallic Micro- and Nanostructured Surfaces for Enhanced Flow Boiling

Flow boiling and evaporation in tubes and channels occur in a wide variety of energy systems, such as refrigeration, air conditioning, power generation, electronics cooling, distillation, and purification. In this work, we demonstrate remarkably increased heat transfer coefficients of 270% during refrigerant flow boiling in scalable microstructured (~40 µm), industrial-scale (~1 m long) aluminum (Al) tubes, when compared to smooth unstructured Al tubes. To achieve scalable nanomanufacturing, we create highly conformal and durable structured surfaces by relying on hydrochloric acid Al etching. Flow boiling tests were conducted in 6.35 mm diameter Al tubes using R134a refrigerant as the working fluid. To benchmark our approach and to elucidate the effect of the structure length scale, we also fabricated ultrascalable boehmite (AlO(OH)) nanostructured (~300 nm) Al tubes, showing that etched microscale features are necessary and key to enhancement. Durability tests conducted using a 28 day long continual flow boiling experiment demonstrated negligible degradation of the etched surfaces. The scalable and cost-effective techniques used to create these durable, etched-Al microstructures may significantly reduce manufacturing cost when contrasted with current enhancement approaches such as extrusion, drawing, and welding.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Challenges in atomic layer etching of gallium nitride using surface oxidation and ligand-exchange

Two atomic layer etching (ALE) methods were studied for crystalline GaN, based on oxidation, fluorination, and ligand exchange. Etching was performed on unintentionally doped GaN grown by hydride vapor phase epitaxy. For the first step, the GaN surfaces were oxidized using either water vapor or remote O 2 -plasma exposure to produce a thin oxide layer. Removal of the surface oxide was addressed using alternating exposures of hydrogen fluoride (HF) and trimethylgallium (TMG) via fluorination and ligand exchange, respectively. Several HF and TMG super cycles were implemented to remove the surface oxide. Each ALE process was monitored in situ using multiwavelength ellipsometry. X-ray photoelectron spectroscopy was employed for the characterization of surface composition and impurity states. Additionally, the thermal and plasma-enhanced ALE methods were performed on patterned wafers and transmission electron microscopy (TEM) was used to measure the surface change. The x-ray photoelectron spectroscopy measurements indicated that F and O impurities remained on etched surfaces for both ALE processes. Ellipsometry indicated a slight reduction in thickness. TEM indicated a removal rate that was less than predicted. In conclusion, we suggest that the etch rates were reduced due to the ordered structure of the oxide formed on crystalline GaN surfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Pulsed laser induced atomic layer etching of silicon

Here, we demonstrate the laser mediated atomic layer etching (ALEt) of silicon. Using a nanosecond pulsed 266 nm laser focused loosely over and in a parallel configuration to the surface of the silicon, we dissociate Cl 2 gas to induce chlorination. Then, we use pulsed picosecond irradiation to remove the chlorinated layer. Subsequently, we perform continuous wave (CW) laser annealing to eliminate amorphization caused by the picosecond laser etching. Based on atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS), we observed strong evidence of chlorination and digital etching at 0.85 nm etching per cycle with good uniformity.

42 ENGINEERING↗
DOE OSTI2023

Bias-pulsed atomic layer etching of 4H-silicon carbide producing subangstrom surface roughness

A new approach to atomic layer etching (ALE) has been demonstrated, and its application to 4H-SiC is reported here. By pulsing only the DC bias for an Ar/Cl2 inductively coupled plasma-reactive ion etching system, the etch cycle duration is reduced by more than an order of magnitude relative to conventional ALE processes. Gas flows are not changed throughout the ALE process. With this process protocol, we achieved an etch rate of 2.48±0.09 Å/cycle with 6 s cycles, an RMS surface roughness (Rq) of 0.83±0.08 Å, and an ALE synergy value of S = 99%. The parameters explored within this ALE process demonstrate effective subangstrom smoothening of 4H-SiC surfaces and is well-suited for a variety of classical and quantum device nanofabrication.

42 ENGINEERING↗
DOE OSTI2022

High-Quality Dry Etching of LiNbO3 Assisted by Proton Substitution through H2-Plasma Surface Treatment

The exceptional material properties of Lithium Niobate (LiNbO3) make it an excellent material platform for a wide range of RF, MEMS, phononic and photonic applications; however, nano-micro scale device concepts require high fidelity processing of LN films. Here, we reported a highly optimized processing methodology that achieves a deep etch with nearly vertical and smooth sidewalls. We demonstrated that Ti/Al/Cr stack works perfectly as a hard mask material during long plasma dry etching, where periodically pausing the etching and chemical cleaning between cycles were leveraged to avoid thermal effects and byproduct redeposition. To improve mask quality on X- and Y-cut substrates, a H2-plasma treatment was implemented to relieve surface tension by modifying the top surface atoms. Structures with etch depths as deep as 3.4 µm were obtained in our process across a range of crystallographic orientations with a smooth sidewall and perfect verticality on several crystallographic facets.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multimodal analysis and characterization of the boehmite layer formed on AA6061 before and after alkaline etching

Low-enriched uranium (LEU) alloyed with 10% Mo (U-10Mo) is being considered as a promising alternative to oxide-based dispersion fuel with high-enriched uranium for use in research reactors. The configuration of this proposed LEU monolithic LEU fuel plate consists of a U-10Mo plate-type fuel foil with a 25 µm zirconium interlayer barrier clad with an aluminum alloy (AA6061). In certain research reactors, the clad AA6061 is coated with a boehmite layer to prevent corrosion. The boehmite layer has a high-pH passivation range, which makes it resistant to oxidation. Boehmite is usually formed on the AA6061 surface by autoclave processing. Before the boehmite layer is added, the surface of the AA6061 is cleaned using techniques such as polishing and wet etching. In this study, we use multimodal analysis to examine how pretreatment of AA6061 using polishing followed by alkaline etching affects the chemical composition of the boehmite layer. X-ray photoelectron microscopy (XPS), transmission electron microscopy (TEM), and x-ray diffraction (XRD) were used to study the chemical changes in the boehmite layer caused by alkaline etching pretreatment. XPS provides quantitative analysis for the Al:O ratio as well as oxidation states present on the surface, which suggests slight oxidation of the boehmite surface after alkaline etching of the AA6061 surface. We further explored this suggested oxidation of the boehmite surface using high-resolution transmission electron microscopy with selected area electron diffraction (SAED) and grazing incidence x-ray diffraction (GI-XRD), which suggested only a small amount of aluminum oxide at the surface. The multimodal analysis and imaging yielded new insights for optimizing boehmite growth on AA6061 for research reactors.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Si–Cl 2 –Ar + Atomic Layer Etching Window: A Fundamental Study Using Molecular Dynamics Simulations and a Reduced Order Model

Silicon (Si) atomic layer etching (ALE) by alternating exposure to chlorine gas (Cl 2 ) and argon ions (Ar + ) is studied by using molecular dynamics (MD) simulations and a reduced order model (ROM). Here, the purpose of this study is to elucidate the properties of the ALE window, a range of ion energies where the amount of Si etched over a series of cycles is nonzero and nearly independent of ion energy. Experimental studies of the Si–Cl 2 –Ar + ALE system report contradictory results related to the ALE window’s ion energy range. Both MD simulations and the ROM show that there is an ALE window present from approximately 15 to 20 eV for normal incidence argon ions. The Si–Cl 2 –Ar + system, therefore, exhibits a narrow ALE window. The amount of Si etched per cycle is less than one atomic layer because of the higher etch yield of Cl atoms relative to atomic Si and silicon chlorides. A modified version of the ROM with an artificially increased Si physical sputtering threshold energy expands the ALE window, illustrating the importance of the difference in chemical and physical sputtering threshold energies in the ALE window energy range. The ROM is also used to examine the dependence of the EPC on the Ar + ion fluence.

energy↗
DOE OSTI2024

Enhanced superconducting qubit performance through ammonium fluoride etch

The performance of superconducting qubits is often limited by dissipation and two-level systems (TLS) losses. The dominant sources of these losses are believed to originate from amorphous materials and defects at interfaces and surfaces, likely as a result of fabrication processes or ambient exposure. Here, we explore a novel wet chemical surface treatment at the Josephson junction-substrate and the substrate-air interfaces by replacing a buffered oxide etch (BOE) cleaning process with one that uses hydrofluoric acid followed by aqueous ammonium fluoride. We show that the ammonium fluoride etch process results in a statistically significant improvement in median $\text{T}_1$ by $\sim22\%$ (p = 0.002), and a reduction in the number of strongly-coupled TLS in the tunable frequency range. Microwave resonator measurements on samples treated with the ammonium fluoride etch after niobium deposition and etching also show $\sim33\%$ lower TLS-induced loss tangent compared to the BOE treated samples. As the chemical treatment primarily modifies the Josephson junction-substrate interface and substrate-air interface, we perform targeted chemical and structural characterizations to examine materials differences at these interfaces and identify multiple microscopic changes that could contribute to decreased TLS losses.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Carrier Diffusion Lengths in Continuously Grown and Etched-and-Regrown GaN Pin Diodes

Advanced GaN power devices are promising for many applications in high power electronics but performance limitations due to material quality in etched-and-regrown junctions prevent their widespread use. Carrier diffusion length is a critical parameter that not only determines device performance but is also a diagnostic of material quality. Here we present the use of electron-beam induced current to measure carrier diffusion lengths in continuously grown and etched-and-regrown GaN pin diodes as models for interfaces in more complex devices. Variations in the quality of the etched-and-regrown junctions are observed and shown to be due to the degradation of the n-type material. Finally, we observe an etched-and-regrown junction with properties comparable to a continuously grown junction.

42 ENGINEERING↗
DOE OSTI2026

Plasma-assisted atomic layer etching of single-crystal diamond

Applications of near-surface nitrogen-vacancy (NV) centers in diamond are often limited by surface defects created during processing. Understanding and controlling plasma-induced surface damage is important for preserving the optical and spin properties of diamond NV centers. We report molecular dynamics simulations of a novel form of plasma-aided atomic layer etching of diamond. In this proposed scheme, the initial surface modification step consists of Ar + ion bombardment. This creates an amorphous layer at the surface, the thickness of which is controlled by the ion energy. Amorphization is known to help smooth the surface, at least locally, and would also serve to sputter clean an initially contaminated surface. A second step impacts the amorphous carbon layer with O + between about 1 and 5 eV. Simulations show that this energy range will remove the amorphous carbon but will not etch the underlying diamond. Though this energy range is not trivial to achieve in a conventional low-temperature plasma, potential methods for creating these low-energy O + ions are discussed. In addition to a-C etching, the O + impacts are predicted to remove any isolated (100) diamond terraces by selectively attacking the edges of the terraces. The proposed atomic layer etching (ALE) approach reverses the conventional ALE sequence in which the surface modification step is usually chemical modification (oxidation in this case), followed by a removal step using Ar + impacts. This plasma ALE procedure is predicted to create a diamond surface that is atomically flat and defect free.

Draney, J. S. [Princeton University, NJ (United St↗