Some investigations of the general instability of stiffened metal cylinders I : review of theory and bibliography
Explore the source record for details and available documents.
STRESSED SKIN - SHELLS↗
SEARCH · Search NASA
Results for “flat sheet”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Effects of Various Heat Treatments on the Ballistic Impact Properties of Inconel 718 Investigated
Uncontained failures of aircraft engine fan blades are serious events that can cause equipment damage and loss of life. Federal Aviation Administration (FAA) certification requires that all engines demonstrate the ability to contain a released fan blade with the engine running at full power. However, increased protection generally comes at the expense of weight. Proper choice of materials is therefore imperative to an optimized design. The process of choosing a good casing material is done primarily through trial and error. This costly procedure could be minimized if there was a better understanding of the relationships among static material properties, impact properties, and failure mechanisms. This work is part of a program being conducted at the NASA Glenn Research Center at Lewis Field to study these relationships. Ballistic impact tests were conducted on flat, square sheets of Inconel 718 that had been subjected to different heat treatments. Two heat treatments and the as-received condition were studied. In addition, results were compared with those from an earlier study involving a fourth heat treatment. The heat treatments were selected on the basis of their effects on the static tensile properties of the material. The impact specimens used in this study were 17.8-cm square panels that were centered and clamped over a 15.2-cm square hole in a 1.27-cm-thick steel plate. Three nominal plate thickness dimensions were studied, 1.0, 1.8, and 2.0 mm. For each thickness, all the specimens were taken from the same sheet of material. The projectile was a Ti-6Al-4V cylinder with a length of 25.4 mm, a diameter of 12.7 mm, and a mass ranging from 14.05 to 14.20 g. The projectiles were accelerated toward the specimens at normal incidence using a gas gun with a 2-m-long, 12.7-mm inner-diameter barrel. The ballistic limit for each heat treatment condition and thickness was determined by conducting a number of impact tests that bracketed as closely as possible the velocity required to penetrate the specimen.
Pereira, J. Michael↗
Controllable Curved Mirrors Made from Single-Layer EAP Films
A document proposes that lightweight, deployable, large-aperture, controllable curved mirrors made of reflectively coated thin electroactive-polymer (EAP) films be developed for use in spaceborne microwave and optical systems. In these mirrors, the EAP films would serve as both structures and actuators. EAPs that are potentially suitable for such use include piezoelectric, electrostrictive, ferroelectric, and dielectric polymers. These materials exhibit strains proportional to the squares of applied electric fields. Utilizing this phenomenon, a curved mirror according to the proposal could be made from a flat film, upon which a nonuniform electrostatic potential (decreasing from the center toward the edge) would be imposed to obtain a required curvature. The effect would be analogous to that of an old-fashioned metalworking practice in which a flat metal sheet is made into a bowl by hammering it repeatedly, the frequency of hammer blows decreasing with distance from the center. In operation, the nonuniform electrostatic potential could be imposed by use of an electron gun. Calculations have shown that by use of a single- layer film made of a currently available EAP, it would be possible to control the focal length of a 2-m-diameter mirror from infinity to 1.25 m.
Bao, Xiaoqi↗
Cell technology: Advanced silicon sheet
The Flat-plate Solar Array (FSA)-sponsored Fourth Silicon Stress/Strain Workshop reviewed, coordinated, and assessed the progress in understanding and controlling stress and strain during the crystal growth of silicon ribbons. dislocation electrical activity and limits on solar cell efficiency, and on studying the effects of dopants on EFG characteristics. Work on silicon for high-efficiency solar cells, stress-strain relationships in silicon ribbon, and high temperature deformation of dendritic web ribbon was also discussed.
Morrison, Andrew D.↗
Rocky Flats, Colorado, Site
This fact sheet provides information about the Rocky Flats, Colorado, Site
Source record↗
Maxey Flats, Kentucky, Disposal Site
This fact sheet provides information about the Maxey Flats, Kentucky, Disposal Site
Source record↗
A simple model of Birkeland currents
The paper develops a simple representation of the global circuit of Birkeland currents on the basis of a representation of the current density (j) in terms of Euler potentials (alpha, chi). The underlying magnetic field, which shares the potential alpha with j, is assumed to be dipolar, making the model applicable chiefly to region 2 Birkeland currents. A form of j is chosen that gives a current sheet with peak outflow at dawn and peak inflow at dusk (or vice versa), connected across a flat polar cap sheet. The superposition of harmonics of the same type, centered at different 'foci', are found to provide a flexible and powerful representation of harmonic functions, accurate within less than 1 percent. An interpolation formula by which current sheets of finite width could be consistently represented is developed.
Stern, David P.↗
Simultaneous measurements of energetic ion (50 keV and above) and electron (220 keV and above) activity upstream of earth's bow shock and inside the plasma sheet - Magnetospheric source for the November 3 and December 3, 1977 upstream events
Simultaneous observations of energetic ions and electrons by the IMP 7 and 8 spacecraft are used here to separate temporal variations from spatial variations during the upstream ion events observed on December 3, 1977 and November 2-3, 1977, in order to determine the source of these particles. Analysis of the observations and comparison with theory shows that: (1) for each of the observed upstream enhancements, energetic ions and electrons were simultaneously present inside the plasma sheet; (2) the low-energy ion intensity profile inside the plasma sheet was relatively flat, while at higher energies there was considrable variability; (3) relativistic electron bursts were seen inside the plasma sheet and also upstream of the shock but at substantially reduced intensities; (4) the ion energy spectrum for the December 3 event, extended to energies of about 2 MeV, was identical in form with the plasma sheet and upstream of the shock; (5) ion anisotropies exhibited typically large dawn-dusk or dusk-dawn gradients and large field-aligned streaming away from the bow shock.
Sarris, E. T.↗
Reliably obtaining white light from layered halide perovskites at room temperature
The recent observation of broadband white-light emission from the inorganic sheets of certain layered lead-bromide perovskites has instigated a multitude of studies on this unusual phenomenon. However, the vast majority of layered bromide perovskites have flat (001) inorganic sheets and display a narrow photoluminescence at room temperature. A handful of heavily distorted (001) perovskites display broad emission, but to date, there is no method of predicting which perovskites will produce white light at room temperature prior to screening different organic molecules that can template 2D perovskites and crystallizing and analyzing the material. By studying ten Pb–Cl perovskites, we find that they all exhibit a broad yellow emission, which is strikingly invariant despite different distortions in the inorganic framework seen across the series. We postulate that this broad emission is intrinsic to all layered Pb–Cl perovskites. Although broad, the emission is not white. By adding Br to the Pb–Cl perovskites we obtain both the narrow emission and the broad emission such that the combined emission color smoothly varies from yellow to warm white to cold white as a function of the halide ratio. Thus, alloying Br to Pb–Cl perovskites appears to be a simple and general strategy for reliably obtaining white light at room temperature from (001) perovskites, regardless of the templating effects of the organic molecules, which should greatly expand the number of white-light-emitting layered perovskites.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Radar-visible wind streaks in the Altiplano of Bolivia
Isolated knobs that are erosional remnants of central volcanoes or of folded rocks occur in several areas of the Altiplano are visible on both optical and images. The optically visible streaks occur in the immediate lee of the knobs, whereas the radar visible streaks occur in the zone downwind between the knobs. Aerial reconnaissance and field studies showed that the optically visible streaks consist of a series of small ( 100 m wide) barchan and barchanoid dunes, intradune sand sheets, and sand hummocks (large shrub coppice dunes) up to 15 m across and 5 m high. On LANDSAT images these features are poorly resolved but combine to form a bright streak. On the radar image, this area also appears brighter than the zone of the radar dark streak; evidently, the dunes and hummocks serve as radar reflectors. The radar dark streak consists of a relatively flat, smooth sand sheet which lacks organized aerolian bedforms, other than occasional ripples. Wind velocity profiles show a greater U value in the optically bright streak zone than in the radar dark streak.
Greeley, R.↗
Heliospheric current sheet inclinations predicted from source surface maps
The inclinations of the neutral line at the ecliptic plane derived from source surface model maps of coronal fields are measured for the interval from June 1976 to March 1992. The mean and median values of 53 deg and 57 deg are close to the average inclinations determined earlier from minimum variance analyses of solar wind measurements at sector boundaries, but the mode falls in the 80 deg - 90 deg bin. This result, which is based on the model assumptions implicit in deriving the source surface maps, predicts that the heliospheric current sheet typically intersects the ecliptic plane nearly at right angles, even without steepening by stream interaction regions. High inclinations dominate the solar cycle for about 7 years around solar maximum. Dips to lower inclination occur near solar minimum, but high variance admits a wide range of inclinations throughout the cycle. Compared to the smooth solar cycle variation of the maximum latitudinal excursion of the neutral line, often treated as the tilt angle of a flat heliospheric current sheet, the noisy variation of the inclinations reflects the degree to which the neutral line deviates from a sine wave, implying warps and corrugations in the current sheet. About a third of the time the neutral line so deviates that it doubles back in longitude.
Shodhan, S.↗
Probing the electronic structure of graphene sheets with various thicknesses by scanning transmission X-ray microscopy
The electronic structure of an aggregation of graphene sheets with various thicknesses was probed by scanning transmission X-ray microscopy. A uniform oxidation of the graphene sheets in the flat area was observed regardless of the thickness, while in the folded area the result could be strongly affected by the geometry. Moreover, thick parts of the aggregation showed strong angle-dependence to the incident X-ray, while thin parts showed less angle-dependence, which might be related to the surface wrinkles and ripples. The electronic structure differences due to the geometry and thickness suggest a complicated situation in the aggregation of graphene sheets.
74 ATOMIC AND MOLECULAR PHYSICS↗
Carbonate Platform Development and Stromatolite Morphogenesis: Constraints on Environmental and Biological Evolution
Work has been completed on the digital mapping of a terminal Proterozoic reef complex in Namibia. This complex formed an isolated carbonate platform developed downdip on a carbonate ramp of the Nama Group. The stratigraphic evolution of the platform was digitally reconstructed from an extensive dataset that was compiled by using digital surveying technologies. The platform comprises three accommodation cycles in which each subsequent cycle experienced progressively greater influence of a long-term accommodation increase. Aggradation and progradation during the first cycle resulted in a flat, uniform, sheet-like platform. The coarsening and shallowing-upward sequence representing the first cycle is dominated by columnar stromatolitic thrombolites and massive dolostones with interbedded mudstone-grainstone at the base of the sequence grading into cross-bedded dolostones. The second cycle features aggradation, formation of a distinct margin containing thrombolite mounds and domes, and the development of a bucket geometry. Columnar stromatolitic thrombolites dominate the platform interior. The final stage of platform development shows a deepening trend with initial aggradation and formation of well-bedded, thin deposits in the interior and mound development at the margins. While the interior drowned, the platform margin kept up with rising sea level and a complex pinnacle reef formed containing fused and coalesced thrombolite mounds flanked by bioclastic grainstones (containing Cloudina and Namacalathus fossils) and collapse breccias. A set of isolated large thrombolite mounds flanked by shales indicate the final stage of the carbonate platform. During a progressive increase in accommodation, a flat-topped isolated carbonate platform becomes aerially less extensive by either backstepping or formation of smaller pinnacles or a combination of both. The overall geometric evolution of the studied platform from flat-topped to bucket with elevated margins is recorded in many Proterozoic and Phanerozoic isolated carbonate platforms with similar dimensions. The terminal Proterozoic, microbial-dominated, isolated carbonate platform of this study clearly illustrates that the answer to accommodation changes was already familiar among carbonate platforms before the dawn of metazoan-dominated platforms.
Grotzinger, John P.↗
High temperature phonon dispersion in graphene using classical molecular dynamics
Phonon dispersion and phonon density of states of graphene are calculated using classical molecular dynamics simulations. In this method, the dynamical matrix is constructed based on linear response theory by computing the displacement of atoms during the simulations. The computed phonon dispersions show excellent agreement with experiments. The simulations are done in both NVT and NPT ensembles at 300 K and found that the LO/TO modes are getting hardened at the Γ point. The NPT ensemble simulations capture the anharmonicity of the crystal accurately and the hardening of LO/TO modes is more pronounced. We also found that at 300 K the C-C bond length reduces below the equilibrium value and the ZA bending mode frequency becomes imaginary close to Γ along K-Γ direction, which indicates instability of the flat 2D graphene sheets.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Experimental measurement of the effective contact angle for solvent/packing interactions in a structured packed column for CO 2 capture
The contact angle is a critical factor for determining the effective mass transfer area for carbon dioxide (CO 2 ) capture via the chemical absorption process in a packed column, and thus the overall capture efficiency of the packed column. Many widely used commercial packings involve microscale features (perforation, corrugation, etc.) that may also affect the wetting behavior. This study proposes a systematic method of using a modified Wilhelmy plate to measure the effective contact angle to characterize the solvent and featured packing interaction. In lieu of computational efforts relying on assumptions guided by semi-informed correlation, the proposed method directly measures the effective contact angle as a function of the solvent and packing thermophysical and hydrodynamic properties. The characterization of the effective contact angle is then integrated in the computational fluid dynamics modeling to reduce uncertainty in the prediction of effective mas transfer area. Experiments were conducted for stainless steel coupons using water and aqueous sodium hydroxide (NaOH) solvent for verification of the proposed experimental protocol. The surface tension of the aqueous NaOH solvent was altered using surfactant and antifoam. The effective contact angle increases with the increased value of the surface tension for flat stainless steel sheets. On the other hand, effective contact angles do not vary in Mellapak coupons for aqueous monoethanolamine (MEA) and NaOH solvent. In this case, surface textures and sheet design play a dominant role in the surface tension of solvents. Furthermore, CO 2 loading has a significant effect on the contact angle for Mellapak coupons. As expected, the contact angle decreases with the increasing temperature of CO 2 capture solvents (MEA, EEMPA). The effective contact angle measurement using the Wilhelmy plate method can provide more accurate and efficient solvents for characterizing the solvent-packing surface interactions. Subsequently, the present method enhances the accuracy of the prediction of the effective mass transfer area in carbon capture by solvent absorption.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Biaxial load effects on the crack border elastic strain energy and strain energy rate
The validity of the singular solution (first term of a series representation) is investigated for the crack tip stress and displacement field in an infinite sheet with a flat line crack with biaxial loads applied to the outer boundaries. It is shown that if one retains the second contribution to the series approximations for stress and displacement in the calculation of the local elastic strain energy density and elastic strain energy rate in the crack border region, both these quantities have significant biaxial load dependency. The value of the J-integral does not depend on the presence of the second term of the series expansion for stress and displacement. Thus J(I) is insensitive to the presence of loads applied parallel to the plane of the crack.
Eftis, J.↗
Some recent theoretical and experimental developments in fracture mechanics
Recent theoretical and experimental developments in four distinct areas of fracture mechanics research are described. These are as follows: experimental comparisons of different nonlinear fracture toughness measures, including the nonlinear energy, R curve, COD and J integral methods; the singular elastic crack-tip stress and displacement equations and the validity of the proposition of their general adequacy as indicated, for example, by the biaxially loaded infinite sheet with a flat crack; the thermodynamic nature of surface energy induced by propagating cracks in relation to a general continuum thermodynamic description of brittle fracture; and analytical and experimental aspects of Mode II fracture, with experimental data for certain aluminum, steel and titanium alloys.
Liebowitz, H.↗
Biaxial load effects in fracture mechanics
It is found that the standard expressions for elastic stress and displacement in the crack-tip region (i.e., the so-called singular solution) cannot be considered to be approximations that are acceptable in a completely general sense. This conclusion is best illustrated by the instance of a biaxially loaded infinite sheet with a flat horizontal central crack, where the effect of load applied parallel to the plane of the crack appears entirely in the second terms of the series representations for local stresses and displacements. An elastoplastic finite-element analysis of the same biaxially loaded finite specimen geometry shows that the global energy release rate, the J-integral, the plastic stress and strain intensity factors (in the sense of Hilton and Hutchinson), and the size of the crack border region plastic yield, all have pronounced biaxial load dependence.
Liebowitz, H.↗