Search NASA⌕ Search

SEARCH · Search NASA

Results for “floating wind technology”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

111 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

The influence of wind veer and drivetrain flexibility on fatigue loading for large floating wind turbines

To reduce costs, offshore wind turbines are expected to be designed with significantly increased rotor diameters. Larger turbines become more flexible and span a larger portion of the atmospheric boundary layer. With these changes, the validity of traditional modeling assumptions should be investigated. This work challenges two common assumptions: (1) that the drivetrain can be considered rigid (except in torsion) and does not couple with the rotor and tower and 2) that wind directional change with height (veer) does not greatly influence the fatigue damage in the tower, blades and drivetrain. Two large semi-submersible floating wind turbines are considered: a 15 and a 22 MW reference turbine. Both use direct-drive generators. Aero-hydro-servo-elastic simulations are performed using OpenFAST, with drivetrain bending flexibility and main bearing response implemented in the coupled analysis. The turbines are subjected to a set of load cases at below-, near- and above-rated mean wind speeds, assembled based on the 3 km Norwegian reanalysis (NORA3) hourly wind and wave hindcast data for Utsira Nord, off the coast of Norway. In each load case, conditions with and without veer are simulated to evaluate the influence of veer on damage equivalent loads (DELs) of the turbine tower, blades and main bearings. Further, these load cases are applied to evaluate the influence of drivetrain flexibility on aero-elastic turbine response. The results indicate that, depending on the veer gradient, mean wind speed, operating regime and turbine size, veer can be very important for tower-top DELs and the fluctuations of main bearing radial loads, while main bearing and blade-root flapwise DELs are less affected. Considering these specific load cases and turbine models, drivetrain flexibility is found to significantly influence tower-top DELs of the largest turbine: the tower-top fore-aft and torsional damage equivalent moments of the 22 MW turbine are reduced by more than 20 % at near-rated wind speeds when the drivetrain is modeled as flexible.

17 WIND ENERGY↗
DOE OSTI2025

OC7 phase I: Toward practical sea-state-dependent modeling of hydrodynamic viscous drag and damping

Here, this article presents a collaborative research campaign under the OC7 project on refining the engineering modeling approach for hydrodynamic viscous drag and damping on floating wind platforms, focusing on the adjustment of hydrodynamic drag and damping coefficients for different sea states. The participant simulation results show significant improvements over the previous OC6 project in predicting the low-frequency resonance motion under nonoperational conditions. The improvements are mainly due to enhanced modeling, including the adoption of wave stretching, and directly tuning the coefficients to measured platform motion in waves instead of free decay. For accurate predictions of mean- and slow-drift motion, the better performing models use a decreasing column splash zone drag coefficient and increasing surge damping/drag with increasing wave height. The model tuning for heave and pitch resonance shows less consistency. Generally, both quadratic drag and additional heave or pitch damping are needed for accurate predictions. Alternatively, a quadratic drag formulation with velocity filtering for the rectangular pontoons leads to improved predictions without additional damping. This model is also potentially more predictive, requiring minimal adjustment to its parameters for different conditions.

17 WIND ENERGY↗
DOE OSTI2026

OC7 phase I: CFD investigation of viscous forces on rectangular members of semisubmersibles

In Phase I of the Offshore Code Comparison Collaboration 7 (OC7) project, we aim to address key questions related to the modeling of viscous hydrodynamic loads on floating platforms. Here, this paper presents results from a collaborative effort within Phase I of the OC7 project. We investigate viscous forces acting on the rectangular members of semisubmersible platforms using high-fidelity computational fluid dynamics (CFD) simulations. The parametric CFD analyses include two-and-a-half-dimensional (2.5D) simulations of pontoon sections of two different semisubmersible platform designs (the VolturnUS-S and the INO WINDMOOR) and full three-dimensional (3D) structure simulations of the VolturnUS-S platform. We extract both the added mass and drag coefficients that are typically used in engineering-level hydrodynamic models from the 2.5D forced oscillation simulations with various Keulegan-Carpenter numbers and compare them to the coefficients from the 3D forced oscillation simulations. We observe consistent variation of the coefficients along the pontoon legs due to 3D platform and free-surface effects. With the breadth of the simulations and component-level detailed analyses, this work establishes a useful database and several empirical formulas for selecting hydrodynamic coefficients when modeling semisubmersible platforms in engineering tools.

13 HYDRO ENERGY↗