SEARCH · Search NASA

Results for “flutter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Laser velocimeter measurements of the flow field generated by a forward-swept propfan during flutter

Results are presented from an investigation to measure the flow field generated by a forward-swept propfan operating in flutter at a low forward velocity. For comparison to the flutter condition, flow field data are also presented for a slightly reduced rotational speed just below flutter. The forward-swept propfan was tested as the front rotor of a counterrotating pusher propeller. A laser Doppler velocimeter (LDV) was used to measure the velocity field in planes normal to the model centerline downstream of the rotor and in planes of constant radius within the blade passages at each operating condition. A comparison of the data taken at the two different operating conditions indicated that the mean, time-averaged flow about the blades did not change drastically as the propfan rotational speed was increased from the stable operating point to the flutter condition. No regions of flow separation could be identified in the data plots of the mean intrablade flow field. The data also indicate that the relative flow about the blades remained subsonic during flutter operation. The blades were found to have a higher than expected tip loading at both operating conditions. This is thought to have been caused by the outer blade sections twisting under load to higher than expected effective blade angles. This high tip loading resulted in strong vortices and a very nonuniform flow downstream of the tips of the forward-swept blades. This high tip loading may also have caused the blade flutter.

Podboy, Gary G.↗

NASA NTRS1994

Sensitivity Analysis of Flutter Response of a Wing Incorporating Finite-Span Corrections

Flutter analysis of a wing is performed in compressible flow using state-space representation of the unsteady aerodynamic behavior. Three different expressions are used to incorporate corrections due to the finite-span effects of the wing in estimating the lift-curve slope. The structural formulation is based on a Rayleigh-Pitz technique with Chebyshev polynomials used for the wing deflections. The aeroelastic equations are solved as an eigen-value problem to determine the flutter speed of the wing. The flutter speeds are found to be higher in these cases, when compared to that obtained without accounting for the finite-span effects. The derivatives of the flutter speed with respect to the shape parameters, namely: aspect ratio, area, taper ratio and sweep angle, are calculated analytically. The shape sensitivity derivatives give a linear approximation to the flutter speed curves over a range of values of the shape parameter which is perturbed. Flutter and sensitivity calculations are performed on a wing using a lifting-surface unsteady aerodynamic theory using modules from a system of programs called FAST.

Issac, Jason Cherian↗

NASA NTRS2003

Resonance Effects in the NASA Transonic Flutter Cascade Facility

Investigations of unsteady pressure loadings on the blades of fans operating near the stall flutter boundary are carried out under simulated conditions in the NASA Transonic Flutter Cascade facility (TFC). It has been observed that for inlet Mach numbers of about 0.8, the cascade flowfield exhibits intense low-frequency pressure oscillations. The origins of these oscillations were not clear. It was speculated that this behavior was either caused by instabilities in the blade separated flow zone or that it was a tunnel resonance phenomenon. It has now been determined that the strong low-frequency oscillations, observed in the TFC facility, are not a cascade phenomenon contributing to blade flutter, but that they are solely caused by the tunnel resonance characteristics. Most likely, the self-induced oscillations originate in the system of exit duct resonators. For sure, the self-induced oscillations can be significantly suppressed for a narrow range of inlet Mach numbers by tuning one of the resonators. A considerable amount of flutter simulation data has been acquired in this facility to date, and therefore it is of interest to know how much this tunnel self-induced flow oscillation influences the experimental data at high subsonic Mach numbers since this facility is being used to simulate flutter in transonic fans. In short, can this body of experimental data still be used reliably to verify computer codes for blade flutter and blade life predictions? To answer this question a study on resonance effects in the NASA TFC facility was carried out. The results, based on spectral and ensemble averaging analysis of the cascade data, showed that the interaction between self-induced oscillations and forced blade motion oscillations is very weak and can generally be neglected. The forced motion data acquired with the mistuned tunnel, when strong self-induced oscillations were present, can be used as reliable forced pressure fluctuations provided that they are extracted from raw data sets by an ensemble averaging procedure.

Lepicovsky, J.↗

NASA NTRS2003

Investigation of the Flow Physics Driving Stall-Side Flutter in Advanced Forward Swept Fan Designs

Flutter-free operation of advanced transonic fan designs continues to be a challenging task for the designers of aircraft engines. In order to meet the demands of increased performance and lighter weight, these modern fan designs usually feature low-aspect ratio shroudless rotor blade designs that make the task of achieving adequate flutter margin even more challenging for the aeroelastician. This is especially true for advanced forward swept designs that encompass an entirely new design space compared to previous experience. Fortunately, advances in unsteady computational fluid dynamic (CFD) techniques over the past decade now provide an analysis capability that can be used to quantitatively assess the aeroelastic characteristics of these next generation fans during the design cycle. For aeroelastic applications, Mississippi State University and NASA Glenn Research Center have developed the CFD code TURBO-AE. This code is a time-accurate three-dimensional Euler/Navier-Stokes unsteady flow solver developed for axial-flow turbomachinery that can model multiple blade rows undergoing harmonic oscillations with arbitrary interblade phase angles, i.e., nodal diameter patterns. Details of the code can be found in Chen et al. (1993, 1994), Bakhle et al. (1997, 1998), and Srivastava et al. (1999). To assess aeroelastic stability, the work-per-cycle from TURBO-AE is converted to the critical damping ratio since this value is more physically meaningful, with both the unsteady normal pressure and viscous shear forces included in the work-per-cycle calculation. If the total damping (aerodynamic plus mechanical) is negative, then the blade is unstable since it extracts energy from the flow field over the vibration cycle. TURBO-AE is an integral part of an aeroelastic design system being developed at Honeywell Engines, Systems & Services for flutter and forced response predictions, with test cases from development rig and engine tests being used to validate its predictive capability. A recent experimental program (Sanders et al., 2002) was aimed at providing the necessary unsteady aerodynamic and vibratory response data needed to validate TURBO-AE for fan flutter predictions. A comparison of numerical TURBO-AE simulations with the benchmark flutter data is given in Sanders et al. (2003), with the data used to guide the validation of the code and define best practices for performing accurate unsteady simulations. The agreement between the analyses and the predictions was quite remarkable, demonstrating the ability of the analysis to accurately model the unsteady flow processes driving stall-side flutter.

Sanders, Albert J.↗

NASA NTRS1961

Supersonic Panel Flutter Test Results for Flat Fiber-Glass Sandwich Panels with Foamed Cores

Flutter tests have been made on flat panels having a 1/4 inch-thick plastic-foam core covered with thin fiber-glass laminates. The testing was done in the Langley Unitary Plan wind tunnel at Mach numbers from 1.76 t o 2.87. The flutter boundary for these panels was found to be near the flutter boundary of thin metal panels when compared on the basis of an equivalent panel stiffness. The results also demonstrated that the depth of the cavity behind the panel has a pronounced influence on flutter. Changing the cavity depth from 1 1/2 inches to 1/2 inch reduced the dynamic pressure at start of flutter by 40 percent. No flutter was obtained when the spacers on the back of the panel were against the bottom of the cavity.

Tuovila, W. J.↗

NASA NTRS2002

Fan Stall Flutter Flow Mechanism Studied

Modern turbofan engines employ a highly loaded fan stage with transonic or low-supersonic velocities in the blade-tip region. The fan blades are often prone to flutter at off-design conditions. Flutter is a highly undesirable and dangerous self-excited mode of blade oscillations that can result in high-cycle fatigue blade failure. The origins of blade flutter are not fully understood yet. Experimental data that can be used to clarify the origins of blade flutter in modern transonic fan designs are very limited. The Transonic Flutter Cascade Facility at the NASA Glenn Research Center was developed to experimentally study the details of flow mechanisms associated with fan flutter. The cascade airfoils are instrumented to measure high-frequency unsteady flow variations in addition to the steady flow data normally recorded in cascade tests. The test program measures the variation in surface pressure in response to the oscillation of one or more of the cascade airfoils. However, during the initial phases of the program when all airfoils were in fixed positions, conditions were found where significant time variations in the pressures near the airfoil leading edges could be observed.

Lepicovsky, Jan↗

NASA NTRS2003

Forward-Swept Fan Flutter Calculated Using TURBO Code

Flutter, a self-excited dynamic instability arising because of fluid structure interaction, can be a significant design problem for rotor blades in gas turbines. Blade shapes influenced by noise-reduction requirements increase the likelihood of flutter in modern blade designs. Validated numerical methods provide designers an invaluable tool to calculate and avoid the flutter instability during the design phase. Toward this objective, a flutter analysis code, TURBO, was developed and validated by researchers from the NASA Glenn Research Center and other researchers working under grants and contracts with Glenn. The TURBO code, which is based on unsteady three-dimensional Reynolds-averaged Navier-Stokes equations was used to calculate the observed flutter of a forward-swept fan. The forward-swept experimental fan, designed to reduce noise, showed flutter at part-speed conditions during wind tunnel tests.

Srivastava, Rakesh↗

NASA NTRS1958

Summary of Flutter Experiences as a Guide to the Preliminary Design of Lifting Surfaces on Missiles

Presented is a limited review of some experiences in flight testing of missiles and of wing flutter investigations that may be of interest in missile design. Several types of flutter of concern in missile studies are briefly described. Crude criteria are presented for two of the most common types of flutter to permit a rapid estimate to be made of the probability of the occurrence of flutter. Many of the details of the flutter problem have been omitted, and only the broader elements have been retained so as to give the designer an overall view of the subject.

VIBRATION AND FLUTTER - BODIES↗

NASA NTRS1957

Results of Two Free-fall Experiments on Flutter of Thin Unswept Wings in the Transonic Speed Range

Results of four thin, unswept, flutter airfoils attached to two freely falling bodies are reported. Two airfoils fluttered at a Mach number of 0.85, a third airfoil fluttered at a Mach number of 1.03, and a fourth fluttered at a Mach number of 1.07. Results of calculations of flutter speed using incompressible and compressible air-force coefficients, including a Mach number of 1.0, are presented.

FLOW, COMPRESSIBLE↗

NASA NTRSDate not supplied

Adjoint-based Sensitivities of Flutter Predictions based on the Linearized Frequency-domain Approach

Flutter is a critical factor in designing and certifying aircraft. The linearized frequency-domain method offers a lower cost alternative to time-marching computational fluid dynamics for high-fidelity flutter analysis. In this work, adjoint-based sensitivities are added to a flutter analysis based on the linearized frequency-domain method to efficiently compute derivatives of flutter cost functions with respect to design variables or uncertain parameters. The derivation of the adjoint equations, which involve complications such as derivatives of a nonlinear generalized eigenvalue problem with complex-valued inputs and derivatives of the linearized Navier-Stokes equations, is provided. The implemented adjoint terms and derivatives are verified before demonstrating the approach for derivatives of flutter dynamic pressure with respect to Mach number for the AGARD 445.6 wing.

Aeroelasticity↗

NASA NTRSDate not supplied

Initial Whirl-Flutter Characterization of the TiltRotor Aeroelastic Stability Testbed

This paper discusses the initial wind tunnel test of the TiltRotor Aeroelastic Stability Testbed (TRAST). TRAST is a generic tiltrotor testbed developed in collaboration between NASA and the Army. Ultimately, this test was a checkout of the model systems, functionality and familiarization, but also obtained subcritical whirl-flutter data in the terms of frequency and damping. Flutter data include two main configurations with different pitch spring stiffness, referred to as 4k and 8k, that were tested at various rotor speeds and airspeeds at the NASA Langley Transonic Dynamics Tunnel. The test included two modes of drivetrain operation: powered and windmilling. However, powered mode of operation was only conducted with the 8k pitch spring. This test reinforced the traditional knowledge of whirl-flutter trends such as flutter speed would decrease with an increase in rotor speed. The critical mode consistently being the wing vertical bending mode. The chord mode as expected was not affected by the pitch spring and was likely to go unstable at a tunnel airspeed slightly beyond the wing vertical bending mode. There were also test specific challenges such as the TRAST modal damping was more sensitive to temperature and amplitude motor than was expected. This test gathered valuable data on the baseline characterization of TRAST, how to improve the model and test practices for future wind tunnel testing. Additionally, a new more automated method for experimental subcritical damping determination based on the Stockwell transform has been demonstrated that may lead to more consistent whirl-flutter stability boundaries.

whirl flutter↗

NASA NTRS1959

Experimental Flutter Investigation of Some Simple Models of a Boost Glide Vehicle Wing at Mach Numbers of 3.0 and 7.3

Results of tests at Mach numbers of 3.0 and 7.3 for possible wing flutter of a series of models of a boost-glide-vehicle wing are presented herein. All of the models were tested at conditions which exceeded the proposed nominal design requirements for the full-scale vehicle; namely, dynamic pressure of 1,000 pounds per square foot at the test Mach numbers. None of the models experienced flutter; therefore, large margins of safety from wing flutter are indicated. However, the effects of body freedoms on the flutter characteristics and local types of flutter were not investigated.

Doggett, Robert V., Jr.↗

NASA NTRS1972

Flutter technology for space shuttle

The development of analytical and experimental techniques needed to predict space shuttle flutter boundaries and insure adequate flutter margins and anticipated problems associated with aeroelastic-model and full-scale testing to validate flutter clearance are considered. Results illustrating the best available tools for subsonic and supersonic flutter prediction are presented. Programs currently underway which will help overcome the difficult problems envisioned for the transonic wind-tunnel and flight flutter test program are also discussed.

Goetz, R. C.↗

NASA NTRS1973

Automated procedure for design of wing structures to satisfy strength and flutter requirements

A pilot computer program was developed for the design of minimum mass wing structures under flutter, strength, and minimum gage constraints. The wing structure is idealized by finite elements, and second-order piston theory aerodynamics is used in the flutter calculation. Mathematical programing methods are used for the optimization. Computation times during the design process are reduced by three techniques. First, iterative analysis methods used to reduce significantly reanalysis times. Second, the number of design variables is kept small by not using a one-to-one correspondence between finite elements and design variables. Third, a technique for using approximate second derivatives with Newton's method for the optimization is incorporated. The program output is compared witH previous published results. It is found that some flutter characteristics, such as the flutter speed, can display discontinous dependence on the design variables (which are the thicknesses of the structural elements). It is concluded that it is undesirable to use such quantities in the formulation of the flutter constraint.

Haftka, R. T.↗

NASA NTRS1973

Flutter analysis and testing of pairs of aerodynamically interfering delta wings

To examine the effect on flutter of the aerodynamic interference between pairs of closely spaced delta wings, several structurally uncoupled 1/80th-scale models were studied by experiment and analysis. Flutter test boundaries run in a 26-in transonic blowdown wind tunnel were compared with subsonic analytical results generated using the doublet lattice method. Trends for several combinations of vertical and longitudinal wing separation showed that flutter speeds can be significantly lowered in closely spaced configurations. For some configurations, a new flutter mechanism, characterized by coupling of the flexible modes from both surfaces at a distinctive flutter frequency, was predicted and observed.

Chipman, R. R.↗

NASA NTRS1973

A computer program for automated flutter solution and matched point determination

The use of a digital computer program (MATCH) for automated determination of the flutter velocity and the matched-point flutter density is described. The program is based on the use of the modified Laguerre iteration formula to converge to a flutter crossing or a matched-point density. A general description of the computer program is included and the purpose of all subroutines used is stated. The input required by the program and various input options are detailed, and the output description is presented. The program can solve flutter equations formulated with up to 12 vibration modes and obtain flutter solutions for up to 10 air densities. The program usage is illustrated by a sample run, and the FORTRAN program listing is included.

Bhatia, K. G.↗

NASA NTRS1974

Transonic single-mode flutter and buffet of a low aspect ratio wing having a subsonic airfoil shape

Transonic flutter and buffet results obtained from wind-tunnel tests of a low aspect ratio semispan wing model are presented. The tests were conducted to investigate potential transonic aeroelastic problems of vehicles having subsonic airfoil sections. The model employed NACA 00XX-64 airfoil sections in the streamwise direction and had a 14 deg leading edge sweep angle. Aspect ratio, and average thickness were 4.0, 0.35, and 8 percent, respectively. The model was tested at Mach numbers from 0.6 to 0.95 at angles of attack from 0 deg to 15 deg. Two zero lift flutter conditions were found that involved essentially single normal mode vibrations. With boundary layer trips on the model, flutter occurred in a narrow Mach number range centered at about Mach 0.90. The frequency and motion of this flutter were like that of the first normal mode vibration. With the trips removed flutter occurred at a slightly high Mach number but in a mode strongly resembling that of the second normal mode.

Erickson, L. L.↗

NASA NTRS1974

Transonic flutter study of a 50.5 deg cropped-delta wing with two rearward-mounted nacelles

Transonic flutter characteristics of three geometrically similar delta-wing models were experimentally determined in the Langley transonic dynamics tunnel at Mach numbers from about 0.6 to 1.2. The models were designed to be simplified versions of an early supersonic transport wing design. The model was an aspect-ratio-1.28 cropped-delta wing with a leadingedge sweep of 50.5 deg. The flutter characteristics obtained for this wing configuration indicated a minimum flutter-speed index near a Mach number of 0.92 and a transonic compressibility dip amounting to about a 27-percent decrease in the flutter-speed index relative to the value at a Mach number of 0.6. Analytical studies were performed for one wing model at Mach numbers of 0.6, 0.7, 0.8, and 0.9 by using both doublet-lattice and lifting-surface (kernel-function) unsteady aerodynamic theory. A comparison of the analytical and experimental flutter results showed good agreement at all Mach numbers investigated.

Sandford, M. C.↗