Search NASA⌕ Search

SEARCH · Search NASA

Results for “frequency control and dynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Structural Damage Detection Using Virtual Passive Controllers

This paper presents novel approaches for structural damage detection which uses the virtual passive controllers attached to structures, where passive controllers are energy dissipative devices and thus guarantee the closed-loop stability. The use of the identified parameters of various closed-loop systems can solve the problem that reliable identified parameters, such as natural frequencies of the open-loop system may not provide enough information for damage detection. Only a small number of sensors are required for the proposed approaches. The identified natural frequencies, which are generally much less sensitive to noise and more reliable than the identified natural frequencies, are used for damage detection. Two damage detection techniques are presented. One technique is based on the structures with direct output feedback controllers while the other technique uses the second-order dynamic feedback controllers. A least-squares technique, which is based on the sensitivity of natural frequencies to damage variables, is used for accurately identifying the damage variables.

Lew, Jiann-Shiun↗
NASA NTRS2002

MIMO Sliding Mode Control for a Tailless Fighter Aircraft, An Alternative to Reconfigurable Architectures

A frequency-domain procedure for the design of sliding mode controllers for multi-input, multi-output (MIMO) systems is presented. The methodology accommodates the effects of parasitic dynamics such as those introduced by unmodeled actuators through the introduction of multiple asymptotic observers and model reference hedging. The design procedure includes a frequency domain approach to specify the sliding manifold, the observer eigenvalues, and the hedge model. The procedure is applied to the development of a flight control system for a linear model of the Innovative Control Effector (ICE) fighter aircraft. The stability and performance robustness of the resulting design is demonstrated through the introduction of significant degradation in the control effector actuators and variation in vehicle dynamics.

Wells, S. R.↗
NASA NTRS1985

Anti-swirling demonstration

Fluid in bearings and seals, involved in motion due to shaft rotation and generating fluid dynamic forces, represents the well recognized source of instability known as whirl and whip. It is characterized by shaft forward circular precession at subysnchronous frequency. Control of the flow pattern in the bearing/seal clearance may enhance the stability. The rotor system demonstrates the dynamic effect of perturbation of the flow pattern in a seal gap by blowing compressed air in the rotor tangential direction. This effect results in shifting the rotor threshold of stability to a higher value of rotative speed when the air jet direction opposes rotation, and to a lower value of rotative speed when the air jet direction coincides with rotation. This effect implies that an unstable rotor can be stabilized by blowing air in the direction opposite to rotation. This technique is known as anti-swirl.

Muszynska, A.↗
NASA NTRS2021

Robust Control Methodology Via Loop Shaping, Root Locus, and Model Reference Control

The paper describes the development of a robust control methodology that can tolerate large uncertainties in plant dynamics in terms of proportional gain variations as well as frequencies and damping. For this to be accomplished, the methodology starts by designing a feedback controller based on a loop shaping technique. The design is then improved by employing a root locus control design approach. Finally, the response of the feedback system is further improved by augmenting the control design using model reference control. The design approach also takes into consideration the speed of the process actuator for a fast response and for high disturbance rejection. Results from two control design examples covered in the paper show that this control approach can tolerate plant proportional gain uncertainty of approximately ± two orders of magnitude with relatively large variations in plant frequencies and damping.

Control Systems↗
DOE OSTI2024

Distributed Automatic Generation Control Considering DPV Using T&D Dynamic Co-Simulation

The increasing adoption of distributed energy resources (DERs) over the last decade warrants a reconsideration of control of generation resources. This paper proposes a distributed Automatic Generation Control (AGC) using transmission-and-distribution (T&D) dynamic co-simulation framework for the efficient DPV frequency regulation services. The co-simulation framework allows AGC units to exchange the information for distributed AGC, based on their adopted communication network topology. As a result, a cost-effective automatic generation control is achieved with DPV and conventional generators. The proposed distributed AGC is based on the gossip algorithm in which the neighboring AGC units share the relevant local information with each other and updates their share of AGC regulation signal. Distributed photovoltaics (DPV) unit contribute to AGC response based on their headroom capacity via DER aggregators. The algorithm is tested on IEEE-14 bus transmission system under conditions of generation failure and random load variation to observe effective frequency regulations service offered by DPVs and other AGC units. The study shows that DPV can effectively participate in AGC with the proposed distributed control framework.

automatic generation control↗
NASA NTRS2001

Dynamic and kinematic strategies for head movement control

This paper describes our analysis of the complex head-neck system using a combination of experimental and modeling approaches. Dynamical analysis of head movements and EMG activation elicited by perturbation of trunk position has examined functional contributions of biomechanically and neurally generated forces in lumped systems with greatly simplified kinematics. This has revealed that visual and voluntary control of neck muscles and the dynamic and static vestibulocollic and cervicocollic reflexes preferentially govern head-neck system state in different frequency domains. It also documents redundant control, which allows the system to compensate for lesions and creates a potential for substantial variability within and between subjects. Kinematic studies have indicated the existence of reciprocal and co-contraction strategies for voluntary force generation, of a vestibulocollic strategy for stabilizing the head during body perturbations and of at least two strategies for voluntary head tracking. Each strategy appears to be executed by a specific muscle synergy that is presumably optimized to efficiently meet the demands of the task.

Non-NASA Center↗
NASA NTRS1980

Second year technical report on-board processing for future satellite communications systems

Advanced baseband and microwave switching techniques for large domestic communications satellites operating in the 30/20 GHz frequency bands are discussed. The nominal baseband processor throughput is one million packets per second (1.6 Gb/s) from one thousand T1 carrier rate customer premises terminals. A frequency reuse factor of sixteen is assumed by using 16 spot antenna beams with the same 100 MHz bandwidth per beam and a modulation with a one b/s per Hz bandwidth efficiency. Eight of the beams are fixed on major metropolitan areas and eight are scanning beams which periodically cover the remainder of the U.S. under dynamic control. User signals are regenerated (demodulated/remodulated) and message packages are reformatted on board. Frequency division multiple access and time division multiplex are employed on the uplinks and downlinks, respectively, for terminals within the coverage area and dwell interval of a scanning beam. Link establishment and packet routing protocols are defined. Also described is a detailed design of a separate 100 x 100 microwave switch capable of handling nonregenerated signals occupying the remaining 2.4 GHz bandwidth with 60 dB of isolation, at an estimated weight and power consumption of approximately 400 kg and 100 W, respectively.

Brandon, W. T.↗
NASA NTRS2020

Aircraft System Identification from Multisine Inputs and Frequency Responses

A frequency-domain approach is described for estimating parameters, such as stability and control derivatives, in aircraft flight dynamic models from measured input and output data. The approach uses orthogonal phase-optimized multisines for moving the aircraft control effectors, Fourier analysis for computing multiple-input multiple-output frequency responses, and a maximum likelihood estimator called frequency response error (FRE) for determining values and uncertainties for the model parameters. The approach is demonstrated using flight test data for two subscale airplanes: the T-2 generic transport model and the X-56A aeroelastic demonstrator. Results and comparisons with the output-error method indicated that the approach produced accurate estimates of stability and control derivatives and their uncertainties from flight test data.

Grauer, Jared A.↗
DOE OSTI2025

Adaptive PID Gain Scheduling Control for Hydropower Turbine Using Neural CDE and Stochastic Distribution Shaping

This paper introduces a gain-scheduling PID controller design strategy for hydroturbine frequency control mode. This scheme first uses real data to learn the nonlinear dynamics of the hydroturbine using neural controlled differential equations and then perturbs the obtained nonlinear system at different equilibrium points, based on which a static output feedback adaptive dynamic programming algorithm is then used to optimize the PID gains for each equilibrium point. Moreover, a continuous-time version of stochastic distribution control is proposed to further fine-tune the optimized PID gains. Finally, the controller is obtained by implementing linear interpolation between the optimized PID control gains. The simulation results show that the proposed gain-scheduling PID controller can control a larger range of operation points compared with the given fixed PID controller and the baseline method. Compared with the given fixed PID controller, the proposed gain-scheduling PID controller can regulate hydroturbine frequency against disturbances induced by power-load variation with over 50% less overshoot for some operation points.

13 HYDRO ENERGY↗
NASA NTRS2019

Real-Time Estimation of Bare-Airframe Frequency Responses from Closed-Loop Data and Multisine Inputs

A method is presented for computing frequency responses of multiple-input multiple-output bare-airframe dynamics from flight test data containing feedback control and/or mixing of control effectors. Orthogonal phase-optimized multisines are used to simultaneously excite each input with unique harmonic frequencies, at which frequency responses are computed as ratios of output-to-input Fourier transform data. The confounding effects of feedback and mixing for frequency response estimation are resolved by interpolating the frequency responses among all the harmonic frequencies. The method can be run in batch for post-flight analysis, or in real time as the aircraft is flying. The effectiveness of the method was verified using closed-loop simulations of the subscale NASA T-2 generic transport airplane. The method was also demonstrated using flight test data from the X-56A MUTT aeroelastic airplane, which was flown with feedback control and mixing.

Jared A Grauer↗
DOE OSTI2025

Stochastic Adaptive Droop Control in Frequency Regulation of Power Systems With Intermittent Generators

Modern power systems (MPSs), including microgrids (MGs), are increasingly incorporating multiple renewable energy sources (RESs) such as wind and solar power, as well as battery storage and controllable loads. While environmentally beneficial, these sources pose challenges for control and management due to their intermittent and stochastic nature, especially in maintaining frequency stability with multiple interconnected generators of varying capacities. Traditional droop control methods are effective in systems with generators that are dispatchable and have fixed generation capacities, but they fall short when applied to systems with RESs, where generation capacities are dynamic and affected by unpredictable environmental conditions. To address these challenges, this paper introduces a novel stochastic adaptive droop control (SADC) method for load frequency control (LFC). The proposed method adapts droop coefficients in real time, based on the measured stochastic data of power generation capacities, enabling more effective frequency regulation in systems with variable and intermittent power generation. Unlike traditional adaptive control methods, which assume constant or slowly-varying system parameters, this approach accounts for stochastic processes by modeling them as Markov chains, enabling robust performance under highly dynamic and unpredictable conditions. The key contributions of this work include the development of real-time droop coefficient adaptation algorithms, derivation of their stability and convergence properties, and the demonstration of the advantages of the method through simulations. Case studies highlight the improved performance of frequency regulation, particularly in addressing the impact of stochastic weather conditions and the benefits of reducing dependence on battery reserves in dealing with intermittency of RESs. Finally, this paper provides a comprehensive analysis of the theoretical foundations of the method, as well as practical implementation insights for future power systems with high penetration of RESs.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS1982

Conceptual design and analysis of a large antenna utilizing electrostatic membrane management

Conceptual designs and associated technologies for deployment 100 m class radiometer antennas were developed. An electrostatically suspended and controlled membrane mirror and the supporting structure are discussed. The integrated spacecraft including STS cargo bay stowage and development were analyzed. An antenna performance evaluation was performed as a measure of the quality of the membrane/spacecraft when used as a radiometer in the 1 GHz to 5 GHz region. Several related LSS structural dynamic models differing by their stiffness property (and therefore, lowest modal frequencies) are reported. Control system whose complexity varies inversely with increasing modal frequency regimes are also reported. Interactive computer-aided-design software is discussed.

Brooks, A. L.↗
NASA NTRS1982

An analytical prediction of pilot ratings utilizing human pilot model

In order to analytically predict pilot ratings, an evaluation method of a manual control system which consists of an aircraft and a human pilot, is proposed and examined. The method is constructed upon the assumptions that the control mission determines the critical frequency the pilot should bring to his focus, and that the degree of closed-loop stability and the human compensation necessary to attain the stability determine the human subjective evaluation of the system. As a result, a simple evaluation chart is introduced. The chart enables prediction of the subjective evaluation, if the controlled element dynamics and the mission are given. The chart is in good accord with almost all of the existing results of pilot ratings. This method has the following advantages: (1) simplicity, in a sense that the method needs to evaluate only two typical controlled element parameters, namely, the gain slope and the phase at the critical control frequency; (2) applicability to unstable controlled elements; (3) predictability of controllability limits of manual control; (4) possibility of estimating human compensatory dynamics.

Tanaka, K.↗
NASA NTRS1987

A comparison of position and rate control for telemanipulations with consideration of manipulator system dynamics

Position and rate control are the two common manual control modes in teleoperations. Human operator performance using the two modes is evaluated and compared. Simulated three-axis pick-and-place operations are used as the primary task for evaluation. First, ideal position and rate control are compared by considering several factors, such as joystick gain, joystick type, display mode, task, and manipulator work space size. Then the effects of the manipulator system dynamics are investigated by varying the natural frequency and speed limit. Experimental results show that ideal position control is superior to ideal rate control, regardless of joystick type or display mode, when the manipulation work space is small or comparable to the human operator's control space. Results also show that when the manipulator system is slow, the superiority of position control disappears. Position control is recommended for small-work-space telemanipulation tasks, while rate control is recommended for slow wide-work-space telemanipulation tasks.

Kim, Won S.↗
NASA NTRS1982

Synthesis of a modern/classical controller for large space structures

The paper is concerned with wide-sense stationary random vibrations of a representative large space structure subject to nonwhite excitations, and with synthesis of its controller amid modeling uncertainties due to truncated modes. Dynamics is analyzed by residue calculus in frequency domain. Steady state variance of a modal coordinate is shown to depend on, among other things, power spectral density of excitation at the modal frequency. Modal cost analysis is performed for an order reduction with a performance objective of attitude, attitude rate and energy control. Optimal and suboptimal output feedback controllers are compared. By treating deleted modes as an additive and a multiplicative perturbation in an idealized transfer function, the low frequency modes omitted according to modal cost analysis are found to cause instability. Finally, the size of the idealized model is shown to be governed by light damping and stringency in performance and stability specifications.

Hablani, H. B.↗
NASA NTRS2023

Control and Scaling Approach for the Emulation of Dynamic Subscale Torque Loads

Research and development of electrified aircraft propulsion powertrains are relying on the use of electromechanical systems to emulate turbomachinery/rotor loads. Replacing a physical turbomachinery/rotor with a model driving a subscale electromechanical system capable of emulating subscale torque loads and responses is a lower risk, lower cost alternative to using the full-scale turbomachinery/rotor for initial control system verification. This paper outlines a novel control and scaling approach for emulating dynamic subscale torque loads using electric machine (EM) hardware for electrified aircraft propulsion research and development purposes. The approach, known as the Sliding Mode Impedance Controller with Scaling (SMICS), drives a mechanically coupled, two-EM system to behave like a subscale hardware representation of a hybrid-electric turbomachinery shaft. One EM reflects the inertial dynamics and torque load of the subscale turbomachinery under steady-state and transient operation while the second EM represents a motor/generator connected to the shaft, which is intended to hybridize the turbomachinery. This closed loop control and scaling algorithm applies impedance and sliding mode control schemes, along with parameter scaling, to match subscale, desired dynamics in real-time and to allow this system to be driven by a full-scale hybrid-electric turbomachinery model and control. The paper elaborates on the concept of the closed loop control and scaling approach and explains the significance of using impedance and sliding mode control. It shows a derivation of the closed loop control and scaling algorithm, its implementation, and presents a comparison of theoretical and actual simulation results acquired during hardware-in-the-loop testing of a partial turboelectric propulsion concept aircraft at the NASA Electric Aircraft Testbed (NEAT).The results show that the intended dynamic responses of the hardware and the aircraft model are achieved in both the time and frequency domain. Full scale propulsion control systems can be tested using this hardware and software approach.

Emulation↗
NASA NTRS2018

Dynamic Modeling using Output-Error Parameter Estimation based on Frequency Responses Estimated with Multisine Inputs

A method is developed for estimating model parameters, such as nondimensional stability and control derivatives, by fitting transfer function or state-space models to empirical frequency response data using the output-error approach. The frequency response data were computed using Fourier transforms of measured input and output data. The control surfaces were excited with periodic multisine inputs which facilitated time-ecient estimation of multiple-input multiple-output frequency responses. The method was applied to lateral data from a nonlinear flight dynamics simulation of the F-16 aircraft, and to longitudinal data from multiple repeated flight test maneuvers of the NASA T-2 subscale aircraft. Results using simulation data showed the frequency response method compared well to other standard methods for parameter estimation. In addition to including all the available inputs, outputs, and harmonic frequencies in the estimation, relatively small subsets of the measured data could also be used to focus on identifying specific parts of the model. Results from flight test data showed that parameter estimates and uncertainties determined from repeated maneuvers were accurate and in statistical agreement with each other.

Grauer, Jared A.↗
NASA NTRS1981

Analytical verification of undesirable properties of direct model reference adaptive control algorithms

The present investigation is concerned with a new method, called 'final approach analysis', which has been developed to analyze the dynamic properties of a class of direct adaptive control algorithms. Particular attention is given to the robustness of these algorithms to a number of aspects. These aspects are related to the generation of high frequencies in the plant control signal, to excessive bandwidth of the adaptive control loop resulting in excitation of unmodeled dynamics, and, consequently, leading to dynamic instability of the closed-loop adaptive system, and, thirdly, to noise corrupted measurements. The final approach analysis is useful because it can be used in a constructive way to adjust the adaptive gains so as to limit the closed-loop system bandwidth and to ameliorate some of the undesirable characteristics of existing adaptive algorithms.

Rohrs, C. E.↗