Search NASA⌕ Search

SEARCH · Search NASA

Results for “fuel melting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Manufacturing porous U10Zr fuels with controlled porosities by SPS and thermal properties

To accommodate the swelling of metallic fuels induced by the fission gas release during burnup in sodium fast reactor for a sodium-free fuel option, advanced U-10Zr fuels with controlled porosity were designed and demonstrated by spark plasma sintering. U-10Zr fuel pellets with manufactured porosities varying from 35% up to fully dense fuel pellets have been fabricated by controlling ball milling times of the starting uranium powders, sintering temperature, pressure, and duration, and the correlation among the microstructure control – porosity – sintering conditions has been established. To further mimick the pore structure in irradiated fuels, different pore formers (NaCl and NH4HCO3) have been used to control the pore size and distribution. Microstructure characterization indicates a lamellar reaction zone of U and Zr, differing from the arc-melted U-10Zr as a result of rapid consolidation of SPS at lower temperature and short durations. The thermal conductivity of U10Zr with different porosities are also measured. Here this work demonstrates the success in manufacturing new metallic fuel forms with controlled porosities and pore distribution, which can be used as model systems to investigate the thermal transfer behavior of metallic fuels in the reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

High temperature steam oxidation dynamics of U 3 Si 2 with alloying additions: Al, Cr, and Y

Uranium silicides are considered for advanced technology reactor fuels due to their enhanced thermal conductivity and high uranium density (U 3 Si and U 3 Si 2 ) compared to traditional UO 2 . Susceptibility to oxidation and wash out, in the event of a cladding breech, could limit the potential for deployment of silicides as accident tolerant fuels. Mitigating the water reaction for U 3 Si 2 could enable its use as an accident tolerant, high uranium density fuel or as a composite fuel constituent. Reported here is the impact of alloying additions of Al, Cr and Y on the high temperature, steam oxidation response of U 3 Si 2 . In addition to the thermogravimetric response, as melted microstructures, phase compositions and post oxidation analysis are also presented. Here, the investigation shows steam oxidation dynamics are altered, from non-alloyed U 3 Si 2 , under thermally ramped conditions. However, additional alloy development of these fuel forms is necessary for further consideration as candidate accident tolerant fuels in water-cooled reactor designs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A case study of high-temperature polyetherimide film capacitor fabrication

Capacitors, as the basic building block of power electronics and electrical systems, are the major constraint of the increasingly integrated power systems that require new capable polymer dielectric films operating at higher temperatures >125 °C. Despite tremendous research efforts on the lab scale, there remains a considerable barrier and knowledge basis for converting polymeric films to functioning capacitors desired in actual applications. Here, the authors tackled the polyetherimide (PEI) film scale up issues and developed various engineering processes for film de-wrinkling, optimal metallization, static elimination, and capacitor fabrication improvement. The authors discovered various fabrication challenges such as the electrostatic charge, metallization scheme, winding tension, and end electrode disconnects. To fabricate a high yield of PEI capacitor bobbins, it is necessary to utilize static eliminators (radioactive ionizers), moderately thick aluminum metallization (15–30 Ω/sq), and winding tension (60–100 g). It is also effective to evaluate capacitance, dielectric loss, equivalent series resistance, and thermal cycling stability of capacitors. This work sheds some light on converting PEI films and other polymeric films to capacitors on a scale up fabrication effort. The practical learning from film handling to capacitor fabrication in this work provided the necessary knowledge for manufacturing high-temperature polar film capacitors.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Surface Tagging of Al 6061-T6 using Photoluminescent Oxides

The goal of tagging nuclear fuels (or related materials, such as fuel cladding) is to provide a persistent marker, traceable to the fuel manufacturer, that can be detected after some length of time, likely after the fuel has been lost, rerouted, or partially destroyed. Ideally, the tag is complicated enough to encode data pertaining to the provenance (manufacturer, date or time, constituents, etc.) and robust enough to survive in-pile exposure and/or further destruction. The taggant should not change the behavior or performance of the fuel in any meaningful way. Photoluminescent tagging was an attractive solution to many of these challenges, as it is undetectable under normal lighting conditions, visible to the naked eye under specific lighting conditions, does not require a significant quantity of material to be photoluminescent, observable with simple commercial detection tools, and is versatile and robust in application. In FY23, the team focused on embedding photoluminescent taggants onto the replicate fuel cladding surface using welding. From a welding standpoint, photoluminescent taggants, in the form of oxides, are a viable option for tagging because the taggants have high melting points, and thus likely to survive welding temperatures (i.e., remain as a secondary phase particle and maintain luminescent properties). Additionally, these taggants have the potential to act as a metal matrix composite which may increase the strength-to-weight ratio, stiffness, and ductility of the base material, all beneficial to cladding and fuel performance.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2025

Exploring scenarios for enhanced fuel compression and performance on the National Ignition Facility with machine-learning-aided design techniques

Recent fusion experiments on the National Ignition Facility (NIF) have achieved ignition, producing multi-MJ fusion yields for input laser energies of roughly 2 MJ [Abu-Shawareb et al., Phys. Rev. Lett. 132, 065102 (2024)]. Building on the success of the target designs that have achieved ignition, we explore new implosion scenarios predicted to generate significantly more compression of the dense DT ice layer and correspondingly higher yields while preserving many of the key physics characteristics of present-day ignition designs. Our main result is a novel 3-shock implosion scheme that effectively minimizes the shock-induced entropy in the dense, accelerating DT shell and maximizes the resulting fuel compression subject to a fixed leading shock strength consistent with present-day ignition experiments, which is necessary to melt the crystalline high-density carbon ablator. Compared to the first NIF experiment to fulfill Lawson's ignition criterion, shot N210808 [Abu-Shawareb et al., Phys. Rev. Lett. 129, 075001 (2022)], our design exhibits a 40% increase in simulated peak areal density (ρR) and a 5× increase in 1D fusion yield using a 4% lighter ablator and identical DT payloads. We also present a complete integrated 2D hohlraum design and laser pulse specifications capable of generating the desired 3-shock drive and maintaining control of the low-mode capsule implosion symmetry, where the increase in simulated 2D yield relative to N210808 is > 10×. This new implosion regime was discovered with help from a machine-learning-enabled capsule design optimization framework. We outline the workflow this automated tool uses to identify improved design candidates by running several rounds of capsule simulations, constructing a surrogate model mapping input variations to key physics output quantities, and querying the resulting statistical model to propose adjustments to the x-ray drive and capsule to reach a set of physics objectives prescribed by the designer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Rheology of lignin and lignin-based solutions, dispersions, gels, polymer blends, and melts

Lignin is an abundant resource that finds application in energy and sustainable materials development. In addition to the utilization of lignin in three-dimensional (3D) printing and hydrogel production, recent studies have reported the use of lignin as a liquid fuel additive. The characterization of the rheological properties of lignin and its derivatives is a dynamic and evolving field, underpinned by advances in experimental, analytical, and modeling techniques. Here, this review provides a comprehensive overview of the recent progress in the study of lignin rheology, highlighting the interplay between structure, modification, and flow behavior in lignin-based solutions, dispersions, gels, polymer blends, and melts. A specific highlight of this review is how lignin concentration affects the rheological properties of lignin-based solutions and dispersions. Furthermore, the effect of lignin type on the properties of 3D-printed lignin-based composites is discussed. For polymer systems, this review discussed lignin-in-polymer solutions separately from lignin-filled polymer systems. Finally, challenges and perspectives on lignin rheology are presented.

Dispersions↗
DOE OSTI2022

Building Structure-Property Relationships of Cycloalkanes in Support of Their Use in Sustainable Aviation Fuels

In 2018 13.7 EJ of fuel were consumed by the global commercial aviation industry. Worldwide, demand will increase into the foreseeable future. Developing Sustainable Aviation Fuels (SAFs), with decreased CO 2 and soot emissions, will be pivotal to the on-going mitigation efforts against global warming. Minimizing aromatics in aviation fuel is desirable because of the high propensity of aromatics to produce soot during combustion. Because aromatics cause o-rings to swell, they are important for maintaining engine seals, and must be present in at least 8 vol% under ASTM-D7566. Recently, cycloalkanes have been shown to exhibit some o-ring swelling behavior, possibly making them an attractive substitute to decrease the aromatic content of aviation fuel. Cycloalkanes must meet specifications for a number of other physical properties to be compatible with jet fuel, and these properties can vary greatly with the cycloalkane chemical structure, making their selection difficult. Building a database of structure-property relationships (SPR) for cycloalkanes greatly facilitates their furthered inclusion into aviation fuels. The work presented in this paper develops SPRs by building a data set that includes physical properties important to the aviation industry. The physical properties considered are energy density, specific energy, melting point, density, flashpoint, the Hansen solubility parameter, and the yield sooting index (YSI). Further, our data set includes cycloalkanes drawn from the following structural groups: fused cycloalkanes, n-alkylcycloalkanes, branched cycloalkanes, multiple substituted cycloalkanes, and cycloalkanes with different ring sizes. In addition, a select number of cycloalkanes are blended into Jet-A fuel (POSF-10325) at 10 and 30 wt%. Comparison of neat and blended physical properties are presented. One major finding is that ring expanded systems, those with more than six carbons, have excellent potential for inclusion in SAFs. Our data also indicate that polysubstituted cycloalkanes have higher YSI values.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Hybrid Ceramic-CMC Vane with EBC for Future Coal Derived Syngas Fired 65% Efficient Turbine Combined Cycle

The efficiency of both simple cycle and combined cycle power generation systems scale with the peak temperature at which the gas exits the combustor to drive the turbine. In conventional systems, a substantial fraction of the total turbine core flow exiting the compressor is diverted downstream to cool metallic turbine hardware rather than power the turbine, much of which is used to cool the first-stage turbine vane. The use of coal derived syngas fuels provides an additional challenge to the lifetime of materials utilized in the turbine, as particulate byproducts created in the coal gasification process melt in the combustion gas, and can subsequently deposit and interact with the turbine hardware. The development of durable hot-section materials capable of operating at temperature well above that of single crystal superalloy airfoil/zirconia based thermal barrier coatings is critical to realizing 65% efficient coal derived syngas fired gas turbine based power systems. To enable higher turbine inlet temperatures while lowering cooling air requirements, United Technologies Research Center (UTRC), the central R&D laboratory supporting UT Pratt & Whitney, led the conceptual design of a new type of ceramic composite turbine hot section materials system. The design focused on a novel hybrid monolithic ceramic-fiber reinforced ceramic matrix composite (CMC) first stage turbine vane having an environmental barrier coating. By utilizing ceramic construction in the turbine hot-section, the core flow normally used to cool metallic components will be substantially reduced, increasing efficiency and reducing emissions. To provide the framework for future demonstration testing, UTRC partnered with University of North Dakota Energy and Environmental Research Center (UNDEERC) to provide a conceptual design for a gasified coal fed high-pressure turbine combustor system designed to mimic the conditions expected in a future 65% fuel to busbar efficient syngas fueled gas turbine based combined cycle. The UNDEERC and UTRC collaborated on characterizing dusts from coal gasifier filtration systems.

10 SYNTHETIC FUELS↗
DOE OSTI2020

Effect of ATF Cr-coated-Zircaloy on BWR In-vessel Accident Progression during a Station Blackout

The deposition of protective coatings on nuclear fuel cladding has been considered as a near-term Accident Tolerant Fuel (ATF) concept that will reduce the high-temperature oxidation rate and enhance accident tolerance of the cladding while providing additional benefits during normal and transient. In this study, the performance of the proposed ATF concept of Cr-coated-Zircaloy is assessed using a generic Boiling Water Reactor MELCOR plant model considering a Short-term Station Blackout (STSBO) scenario. Simulation results indicate that the use of Cr-coated-Zircaloy as cladding and canister material mitigates the core degradation process as compared to the traditional Zircaloy cladding and canister design. The onset of fuel degradation and collapse is delayed by over thirty minutes, and the extent of fuel degradation is reduced. Specifically, the gross in-vessel hydrogen generation decreased by almost a factor of three. Although the eutectic reaction between Cr-coating and Zircaloy could cause an early failure of the coating, the improvement in the delay of fuel degradation is still notable. In addition, a thicker coating is found helpful to obtain additional coping time and to decrease hydrogen generation. In addition to the eutectic formation that may compromise Cr-coated Zr, a different failure mode is identified for the Cr-coated-Zr when compared to Zircaloy; i.e., a complete melt of base material leads to component collapse before the coating is oxidized and consumed. These findings can help the industry focus on productive areas of research and development for accident-tolerant fuel concepts and enhancement of core safety margins.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

AOI [1] Advanced Manufacturing of Ceramic Anchors with Embedded Sensors for Process and Health Monitoring of Coal Boilers

Researchers at West Virginia University (WVU) developed methods to fabricate and test ceramic anchors with an embedded sensor technology for monitoring the health and processing conditions within pulverized coal (PC) and fluidized-bed combustion (FBC) boiler systems. The technology included the development of advanced manufacturing processes for 2D/3D printing electroceramic (conductive ceramic) sensor designs within the ceramic anchor microstructure during the manufacturing process. This advanced manufacturing process would allow for the precise control of local microstructure and composition in order to engineer layer-by-layer any protective and electrically active materials within the refractory anchor. This 3D printing technology would permit the rapid and controlled design of the refractory microstructure and embedded sensor design throughout the volume of the ceramic anchor. The work also included a method to interconnect the sensors to boiler shell through the anchor clamp, where the sensor signals will be processed by low-power electronics and transmitted wirelessly to a central processing hub. The end-goal of the program was to produce a ceramic anchor sensor system which would be ready for implementation within a coal boiler, and/or other similar refractory liner systems (such as that in the glass and metal manufacturing areas). The project objectives were to: 1) Define the chemical and microstructural stability, in addition to the electrical properties, of oxide and non-oxide ceramic composites to be embedded within the ceramic anchor compositions that may operate up to 1400ºC; 2) Develop and implement the 2D/3D printing technology to pattern and control the microstructure of the ceramic anchor and embedded sensor circuits; 3) Develop an interconnect technology which will permit easy installation of the ceramic anchors and signal collection at the boiler shell; 4) Develop low power analog electronics and wireless communication hardware to efficiently collect the sensor signal at each processing unit and transmit data to a central hub for data analysis; 5) Demonstrate the smart ceramic anchor system for temperature and liner fracture within a high-temperature processing unit, such as a boiler furnace or glass melting furnace floor/wall liner.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2020

Design complexity and performance analysis in additively manufactured heat exchangers

The main objective of this research is to investigate the tradeoffs between design complexity and thermal performance in additively manufactured metallic heat exchangers. Such heat exchangers have become a favorite topic for investigation in various fields ranging from air conditioning to aircraft gas turbine engines. In particular, high manufacturing cost has emerged as the major drawback in broad applications of manifold-microchannel heat exchanger (MMHXs). The possibility of cost-effective manufacturing has generated wide interest in applying additive manufacturing (AM) for fabricating MMHXs. Furthermore, AM technologies will provide an opportunity for enhanced design and superior heat transfer performance. In this study, innovative MMHXs are designed and fabricated through selective laser melting. An experimental setup was designed to measure pressure drop and heat transfer for the developed MMHXs with a wide range of Reynolds numbers. Furthermore, the coefficient of performance was calculated based on the heat flow rate, air pressure drop, and air flow rate. Measurement results demonstrated that in some scenarios adding more internal features, i.e., increasing design complexity, does not necessarily improve the MMHX performance.

10 SYNTHETIC FUELS↗
DOE OSTI2026

Irradiation Testing of Additively Manufactured Materials for LWR Applications: Alloy 718 and 316L Stainless Steel

The objective of this NSUF Project is to assess the changes in irradiated additively manufactured (AM) material properties as compared to non-irradiated material. Type 316L stainless steel and Alloy 718 samples were produced using Direct Metal Laser Melting (DMLM) fabrication. Materials produced from this fabrication method have several potential applications within the nuclear industry as reactor internal repair parts, fuel debris resistant filters, or fuel spacers within existing light water reactors (LWRs). AM materials have been shown to achieve equivalent mechanical behavior in simulated reactor environments as compared to wrought materials, but have significantly more flexibility when it comes to unique design features. The increased component design flexibility makes these AM materials an attractive choice for both current LWR applications as well as for small modular reactor (SMR) designs. Prior to use of these materials in reactor fleet operation, the industry as a whole must evaluate the effects of irradiation on their material properties. Standard 0.4 inch thick Compact Tension specimens and SSJ3 type tensile bars were neutron irradiated at the Advanced Test Reactor to ~1 dpa for the purpose of performing a variety of mechanical tests in a range of simulated environments applicable to LWRs. For the ductile austenitic Type 316L stainless steel, the irradiated data will be used to confirm that the AM process produces materials with properties that are equivalent to wrought materials under testing conditions applicable to LWR operation. Transmission electron microscopy analysis was also performed in order to understand microstructural and microchemical changes induced in each material in response to neutron irradiation. If possible, data collected from these AM 316L samples will be used to remove fluence limits from specifications of ASME code cases for this alloy, which will give vendors much more flexibility in building future components.

36 - MATERIALS SCIENCE↗
DOE OSTI2023

Synthesis and thermophysical property determination of NaCl-PuCl3 salts

Currently, a knowledge gap exists in the available data and understanding of thermophysical properties relating to fresh fuel salts, especially those containing plutonium. These data are necessary for designing, constructing, and licensing future commercial molten-salt reactors. Thermophysical properties, such as melting temperature, salt stability, density, and heat capacity were ascertained using NaCl-PuCl3 (36 mol% PuCl3) and a more sodium rich composition containing 25 mol% PuCl3. The NaCl-PuCl3 salt mixture was synthesized for this study and contained 63.4 mol% NaCl, 36.3 mol% PuCl3 and was 99.7% pure. Upon heating, the NaCl–PuCl3 eutectic was stable at temperatures up to 800 °C. The onset of melting occurred at 451 ± 3 °C, and the enthalpy of fusion was determined to be 23.0 ± 1.4 kJ/mol. Heat capacity measurements in the liquid phase ranged from 107.7 to 91.3 J/mol.K, with an average value of 104.6 ± 11.4 J/mol.K between 500 and 650 °C. Three independent trials of the molten NaCl-PuCl3 salt found the density to be ?(T) = 3.8589 – 9.5342·10-4 T(°C). In addition, ab initio molecular dynamic simulations to calculate density and heat capacity values are included.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Carbon supported single atom carbon dioxide reduction electro catalysts

Electrocatalysts composed of single atoms dispersed over porous carbon support were prepared by a lithium-melt method. The new catalysts demonstrated high selectivity, high Faradic efficiency and low overpotential toward to the electrocatalytic reduction of carbon dioxide to fuels.

Liu, Di-Jia↗
DOE OSTI2020

Aluminum-doped U 3 Si 2 composite fuels with enhanced oxidation resistance

Al-doped U 3 Si 2 composite fuels with controlled microstructure were fabricated by spark plasma sintering that display greatly-improved oxidation resistance as compared with monolithic and Al-doped silicides prepared by standard powder metallurgy or arc melting. The effects of Al additives on the thermal-mechanical properties and oxidation resisance of the micron- and nano-sized U 3 Si 2 composites were investigated. Additionally, a minimal addition of 1.8 at% Al is effective to increase the onset oxidation temperature of as-fabricated U 3 Si 2 pellets to 580 °C, which can be further increased to 610 °C by thermal annealing. The Al-doped U 3 Si 2 composite fuels also display simultaneously higher hardness and fracture toughness than un-doped U3Si2. These results highlight an effective strategy by integrating minimal Al additives, microstructure control and post-thermal annealing to design advanced silicide fuels with excellent oxidation resistance, desired thermal-mechanical properties and maintained high fissile element density.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Numerical investigation of magneto-inertial fusion targets magnetized by dynamic enforcement of helical current flow

Magnetized Liner Inertial Fusion (MagLIF) targets require premagnetization to reduce thermal conduction losses from the laser-heated fuel to the liner material during implosion. MagLIF targets are typically magnetized by external magnetic field coils which are technologically limited to providing <20 T axial magnetic fields in the fusion fuel. We present a novel target design, AutoMag-D, which employs dynamic enforcement of helical current in the liner, resulting in >20 T axial magnetic field in the fuel region prior to implosion without the need of external magnetic field coils. These self-magnetizing liners are made of helically oriented alternating electrically conductive material and electrically insulating material surrounded by a thin, conductive outer radial layer. As the liner is pulsed with a ∼ 20 MA, ∼ 100 ns rise time drive current from Z, the outer layer of conductive material is shocked and intensely Joule heated, causing it to melt, vaporize, and turn to plasma. This allows the magnetic drive field to diffuse radially inward which dynamically enforces current flow in the helical conduction paths in the liner and produces axial magnetic field in the fuel region prior to implosion of the inner liner surface. AutoMag-D liner designs do not require dielectric breakdown of electrically insulating material (as in traditional auto-magnetizing helical liners) and do not require helical return current geometries (as in dynamic screw pinches). We present results from three-dimensional radiation-magnetohydrodynamic simulations of MagLIF implosions employing AutoMag-D liner designs. Simulated AutoMag-D targets demonstrate improved fuel conditions and thermonuclear yield compared to traditional MagLIF.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Evaluating the intrinsic resistance to balling of alloys: A High-throughput physics-informed and data-enabled approach

To date, the vast majority of work on metal additive manufacturing (AM) has been framed in terms of the need to tune processing conditions for a particular AM technology in order to print conventional alloys, oftentimes developed for fabrication methods other than AM. This approach overlooks the fact that historically, many engineering alloy system has been designed with a particular processing route in mind, e.g., ingot metallurgy, powder metallurgy, rapid quenching, etc. There are thus significant opportunities to design alloys specifically for AM. A key challenge is that alloy design requires performance metrics that can be optimized by exploring the alloy chemistry space. Here, we present a study in which we examine how intrinsic thermophysical properties can be used to estimate performance metrics related to the behavior of a solidifying metal droplet under AM-relevant conditions. By identifying these intrinsic properties, it is possible to directly incorporate ‘intrinsic printability’, specifically ‘intrinsic resistance to balling’, into AM-focused alloy design.

20 FOSSIL-FUELED POWER PLANTS↗