Search NASA⌕ Search

SEARCH · Search NASA

Results for “high-density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Spacelab high density digital recorders

The design and performance of the high-density digital recorder (HDDR) developed for use at the NASA centers (KSC, JSC, and GSFC) and at the JPL to store and retrieve 50-Mb/s PCM data streams from the Spacelab experiments are reported. The recording reproduction, and transport requirements are reviewed; and the design solutions adopted in the final version of the HDDR are described, incuding three-position-modulation and Y-phase encoding, microprocessor-controlled automatic bit synchronization and equalization, cyclic-redundancy-check error detection and correction, clock regeneration, data and clock variations, tape-speed control, and EEE-488 remote control. Reliable performance, with bit error rates 1 in 10 to the 10th forward and 1 in 10 to the 9th reverse or better and packing density up to 50 percent greater than that obtainable using conventional codes, is reported after 1.5 years of service.

Blais, R. A.↗
NASA NTRS1983

Monolithic short wave infrared (SWIR) detector array

A monolithic self-scanned linear detector array was developed for remote sensing in the 1.1- 2.4-micron spectral region. A high-density IRCCD test chip was fabricated to verify new design approaches required for the detector array. The driving factors in the Schottky barrier IRCCD (Pdsub2Si) process development are the attainment of detector yield, uniformity, adequate quantum efficiency, and lowest possible dark current consistent with radiometric accuracy. A dual-band module was designed that consists of two linear detector arrays. The sensor architecture places the floating diffusion output structure in the middle of the chip, away from the butt edges. A focal plane package was conceptualized and includes a polycrystalline silicon substrate carrying a two-layer, thick-film interconnecting conductor pattern and five epoxy-mounted modules. A polycrystalline silicon cover encloses the modules and bond wires, and serves as a radiation and EMI shield, thermal conductor, and contamination seal.

Source record↗
NASA NTRS1985

Direct measurements of severe spacecraft charging in auroral ionosphere

Questions are addressed concerning how large space structures in polar orbit will interact with auroral environments. Because spacecraft charging at ionospheric attitudes does not seriously threaten the operation of today's relatively small polar satellites the subject of environment interactions has not received the widespread attention given to it at geostationary altitude. As a matter of economics it is desirable to apply as much as possible of what was learned about spacecraft interactions at geostationary orbit to low Earth orbits. The environment at auroral latitudes in the ionosphere differs from that encountered at geostationary altitude in at least two major aspects. (1) There is a large reservoir of high-density, cold plasma which tends to mitigate charging effects by providing a large source of charged particles from which neutralizing currents maybe drawn. Significant wake effects behind large structures will introduce new problems with differential charging. (2) Between the magnetic equator and the ionosphere, auroral electrons frequently undergo field-aligned accelerations of several kilovolts. In such environments, fluxes of energetic protons are usually below the levels of instrumentation sensitivity.

Burke, W. J.↗
NASA NTRS1985

The Effect of Particle Density on Aeolian Transport

A set of experiments using a wide range of particle densities was performed in an open-circuit, terrestrial-atmospheric-pressure wind tunnel at Arizona State University. The results show that saltation flux equations derived for typical geologic material overpredict the flux of low-density particles. Walnut shells (approximately 1.1 g/cc) were used in the experiment and correspond to volcanic ash or ice. Less mass is transported by the wind in the case of low particle density because the style of transport is different. There is a direct, counter-intuitive relationship between particle density and transport height. Measurements of the vertical distribution of material show that the low-density walnut shells travel in a zone within 10 cm of the surface while high-density (approximately 4.5 g/cc) chromite particles travel as 50 cm. Furthermore, the overall saltation rate of the chromite is approximately four times greater than the walnut shells at the same freestream wind speed, even though the wind is much further above threshold for the walnut shells.

Williams, S. H.↗
NASA NTRS1985

Potential Bedforms on Venus: Wind Tunnel Simulations

Wind tunnel studies involving mixtures of particle sizes (bimodal and multimodal distributions) indicate the microdunes and related ridge- and wave-like structures can occur over a wider range of conditions. The results indicate that the bedforms develop as a consequence of the effective sorting capability of the high-density Venusian atmosphere. Four mixtures of different particle-size distributions were investigated. The results of these experiments suggest that: (1) small-scale bedforms on Venus may be more common than previously anticipated from simulations involving only unimodal sands; (2) small particles are rapidly sorted on Venus if winds slightly above threshold are available; (3) coarse particles are transported in traction within the bedforms as well as rolled by saltating fines, suggesting that the capacity of wind on Venus to transport material is greater than anticipated from previous flux studies and (4) microdunes and related ridges and waves with coarse and fine layers can be produced during sorting.

Bougan, S. J.↗
NASA NTRS1984

Stream dynamics between 1 AU and 2 AU: A detailed comparison of observations and theory

A radial alignment of three solar wind stream structures observed by IMP-7 and -8 (at 1.0 AU) and Voyager 1 and 2 (in the range 1.4 to 1.8 AU) in late 1977 is presented. It is demonstrated that several important aspects of the observed dynamical evolution can be both qualitatively and quantitatively described with a single-fluid 2-D MHD numerical model of quasi-steady corotating flow, including accurate prediction of: (1) the formation of a corotating shock pair at 1.75 AU in the case of a simple, quasi-steady stream; (2) the coalescence of the thermodynamic and magnetic structures associated with the compression regions of two neighboring, interacting, corotating streams; and (3) the dynamical destruction of a small (i.e., low velocity-amplitude, short spatial-scale) stream by its overtaking of a slower moving, high-density region associated with a preceding transient flow. The evolution of these flow systems is discussed in terms of the concepts of filtering and entrainment.

Burlaga, L. F.↗
NASA NTRS1984

GASP cloud encounter statistics - Implications for laminar flow control flight

The cloud observation archive from the NASA Global Atmospheric Sampling Program (GASP) is analyzed in order to derive the probability of cloud encounter at altitudes normally flown by commercial airliners, for application to a determination of the feasability of Laminar Flow Control (LFC) on long-range routes. The probability of cloud encounter is found to vary significantly with season. Several meteorological circulation features are apparent in the latitudinal distribution of cloud cover. The cloud encounter data are shown to be consistent with the classical midlatitude cyclone model with more clouds encountered in highs than in lows. Aircraft measurements of route-averaged time-in-clouds fit a gamma probability distribution model which is applied to estimate the probability of extended cloud encounter, and the associated loss of LFC effectiveness along seven high-density routes. The probability is demonstrated to be low.

Jasperson, W. H.↗
NASA NTRS1984

Line emission from H II blister models

Numerical techniques to calculate the thermal and geometric properties of line emission from H II 'blister' regions are presented. It is assumed that the density distributions of the H II regions are a function of two dimensions, with rotational symmetry specifying the shape in three-dimensions. The thermal and ionization equilibrium equations of the problem are solved by spherical modeling, and a spherical sector approximation is used to simplify the three-dimensional treatment of diffuse ionizing radiation. The global properties of H II 'blister' regions near the edges of a molecular cloud are simulated by means of the geometry/density distribution, and the results are compared with observational data. It is shown that there is a monotonic increase of peak surface brightness from the i = 0 deg (pole-on) observational position to the i = 90 deg (edge-on) position. The enhancement of the line peak intensity from the edge-on to the pole-on positions is found to depend on the density, stratification, ionization, and electron temperature weighting. It is found that as i increases, the position of peak line brightness of the lower excitation species is displaced to the high-density side of the high excitation species.

Rubin, R. H.↗
NASA NTRS1985

Broad emission features in QSOs and active galactic nuclei. II - New observations and theory of Fe II and H I emission

Seven QSOs of low to intermediate redshift are characterized on the basis of: 320-850-nm spectra obtained with the UVITS spectrograph and image-dissector scanner at the f/9 Cassegrain focus of the 2.7-m reflecting telescope at McDonald Observatory; improved model calculations for the Fe II, Mg II, and Balmer lines and the Balmer continuum; and the theoretical results of Netzer and Wills (1983). The data are presented in tables, spectra, and difference spectra and described in detail. Fe II is found to be the largest contributor to the emission line spectrum, with strong UV Fe II lines in all QSOs (regardless of the strength of the optical Fe II lines) and an abundance ratio suggesting a factor-of-three overabundance of Fe relative to Mg and probably H. A discrepancy between the observed Fe II strength and the predictions of dustless standard photoionization models is noted, and the addition of a high-density component to the models is suggested.

Wills, B. J.↗
NASA NTRS1985

Coupled low-energy - ring current plasma diffusion in the Jovian magnetosphere

The outwardly diffusing Iogenic plasma and the simultaneously inwardly diffusing ring current plasma in the Jovian magnetosphere are described using a coupled diffusion model which incorporates the effects of the pressure gradient of the ring current into the cross-L diffusion coefficient. The coupled diffusion coefficient is derived by calculating the total energy available to drive the diffusion process. The condition is imposed that the diffusion coefficient takes on a local minimum value at some point in the region L = 7-8, at which point the gradient of the Io plasma density is specified as ramp value given by Siscoe et al. (1981). The hypothesis that the pressure gradient of the ring current causes the diminution of radial plasma transport is tested, and solution profiles for the Iogenic and ring current plasma densities are obtained which imply that the Io plasma ramp is caused by a high-density, low-energy component of the ring current hitherto unobserved directly.

Summers, D.↗
NASA NTRS1985

Electrostatic wave propagation and trapping near the magnetic equator

Results of a two-dimensional ray tracing computer code, based on Snell's law, for electrostatic wave propagation in a dipole magnetic field are discussed. A survey of possible ray paths varying a wide range of parameters is conducted for low-harmonic Bernstein modes in a high-density plasma. It is shown that the ray paths exhibit similarity with radial distance and that there exists the possibility of two classes of wave statistics of the equator: a broad emission region extending to about + or - 4 deg and a class of events restricted to the smaller region of 1-2 deg about the magnetic equator. The regulating parameter between these two types of events is the transition energy from the isotropic background electrons to the unstable distribution of superthermals. Ray paths for propagation in the magnetic equatorial plane are considered and an explanation is given for ray focusing in the equatorial plane based on electron gyroradius considerations.

Barbosa, D. D.↗
NASA NTRS1984

Summary of workshop on the application of VLSI for robotic sensing

It was one of the objectives of the considered workshop to identify near, mid, and far-term applications of VLSI for robotic sensing and sensor data preprocessing. The workshop was also to indicate areas in which VLSI technology can provide immediate and future payoffs. A third objective is related to the promotion of dialog and collaborative efforts between research communities, industry, and government. The workshop was held on March 24-25, 1983. Conclusions and recommendations are discussed. Attention is given to the need for a pixel correction chip, an image sensor with 10,000 dynamic range, VLSI enhanced architectures, the need for a high-density serpentine memory, an LSI-tactile sensing program, an analog-signal preprocessor chip, a smart strain gage, a protective proximity envelope, a VLSI-proximity sensor program, a robot-net chip, and aspects of silicon micromechanics.

Brooks, T.↗
NASA NTRS1985

The ionization of atomic oxygen by electron impact

Single and double ionization of atomic oxygen by electron impact has been studied experimentally. The energy dependence of the specific ionization cross sections sigma(O+) and sigma(O2+) has been measured in the energy range 40-300 eV using a high-density atomic oxygen source not contaminated by metastable O(D-1) or O(S-1) atoms. The ratios of the measured cross sections to absolute values are given in a table.

Zipf, E. C.↗
NASA NTRS1985

Seal Technology for Liquid Oxygen (LOX) Turbopumps

Two types of advanced seals for liquid oxygen (LOX) turbopumps were investigated. One was a spiral-groove face seal whose function is to seal high-pressure LOX at the impeller end of the turbopump. The other was a floating-ring, Rayleigh-step, helium buffered seal used to prevent LOX ingress to the turbine side of the unit. For each seal type, two sizes were investigated (50 and 20 mm). A turbine-driven test rig was designed and manufactured, and a test program was completed on the 50 mm floating-ring, Rayleigh-step, helium buffered seal. Significant results were: vaporization in the flow path could cause failure by overheating; therefore, the spiral-groove pumping portion of the seal that provides the fluid film must circulate fluid without disruption if vaporization occurs in the sealing dam. This is successfully accomplished by a pressure-balanced spiral-groove concept that is described. The spiral-groove configuration is affected by turbulence in the fluid film and pressure drops due to fluid inertia at sudden contractions. The net results of these effects are deep grooves, large operating films, and high power loss when compared against seals operating with laminar films. Turbulence and inertia are induced by the high-density and low-viscosity characteristics of LOX. The program clearly pointed out the need to consider system environmental factors such as thermal and centrifugal distortions and rotor vibrations in the seal design.

Shapiro, Wilbur↗
NASA NTRS1989

Growth and characterization of single crystal insulators on silicon

An overview of the growth and characterization of epitaxial insulators on semiconductors is presented. The potential applications include semiconductor-on-insulator structures, three-dimensional and/or high-density integrated circuits, optoelectronic applications such as integrated waveguides and improved gate insulators. The growth and physical characterization of epitaxial fluorides on semiconductors are discussed. Consideration is also given to the epitaxial overgrowth of epitaxial metal layers with CaF2 as well as to the formation of a novel superlattice of Ca particles in epitaxial CaF2.

Schowalter, Leo J.↗
NASA NTRS1946

Bending-torsion flutter calculations modified by subsonic compressibility corrections

A number of calculations of bending-torsion wing flutter are made at two Mach numbers, m=0 (incompressible case) and m=0.7, and results are compared. The air forces employed for the case of m=0.7 are based on Frazer's recalculation of Possio's results, which are derived on the assumption of small disturbances to the main flow. For ordinary wings of normal density and of low bending frequency in comparison with torsion frequency, the compressibility correction to the flutter speed appears to be of the order of a few percent; whereas the correction to flutter speed for high-density wing sections, such as propeller sections, and to the wing-divergence speed in general, may be based on a rule using the (1 - m(2))1/4 factor and, for m=0.7, represents a decrease of the order of 17 percent.

Garrick, I E↗
NASA NTRS1951

Correlation of physical properties with molecular structure for some dicyclic hydrocarbons having high thermal-energy release per unit volume

As part of a program to study the correlation between molecular structure and physical properties of high-density hydrocarbons, the net heats of combustion, melting points, boiling points, densities, and kinematic viscosities of some hydrocarbons in the 2-n-alkylbiphenyl, 1,1-diphenylalkane, diphenylalkane, 1,1-dicyclohexylalkane, and dicyclohexylalkane series are presented.

Wise, P H↗
NASA NTRS1960

The Hot-Pressing of Hafnium Carbide (Melting Point, 7030 F)

An investigation was undertaken to determine the effects of the hot-pressing variables (temperature, pressure, and time) on the density and grain size of hafnium carbide disks. The purpose was to provide information necessary for the production of high-density test shapes for the determination of physical and mechanical properties. Hot-pressing of -325 mesh hafnium carbide powder was accomplished with a hydraulic press and an inductively heated graphite die assembly. The ranges investigated for each variable were as follows: temperature, 3500 to 4870 F; pressure, 1000 to 6030 pounds per square inch; and time, 5 to 60 minutes. Hafnium carbide bodies of approximately 98 percent theoretical density can be produced under the following minimal conditions: 4230 F, 3500 pounds per square inch, and 15 minutes. Further increases in temperature and time resulted only in greater grain size.

Sanders, William A.↗