Search NASA⌕ Search

SEARCH · Search NASA

Results for “higher heating value”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

An Investigation of the Effects of Heat Transfer on Boundary-Layer Transition on a Parabolic Body of Revolution (NACA RM-10) at a Mach Number of 1.61

Report presents the results of an investigation conducted to determine the effects of heat transfer on boundary-layer transition on a parabolic body of revolution (NACA rm-10 without fins) at Mach number of 1.61 and over a Reynolds number range from 2.5 x 10(6) to 35 x 10(6). The maximum cooling of the model used in these tests corresponded to a temperature ratio (ratio of model-surface temperature to free-stream temperature) of 1.12, a value somewhat higher than the theoretical value required for infinite boundary-layer stability at this Mach number. The maximum heating corresponded to a temperature ratio of about 1.85. Included in the investigation was a study of the effects of surface irregularities and disturbances generated in the airstream on the ability of heat transfer to influence boundary-layer transition.

Czarnecki, K R↗

Process Considerations for the Production of Hydrogen via Steam Reforming of Oxygenated Gases from Biomass Pyrolysis and Other Conversion Processes

Abstract In 2021, average CO 2 emissions was 9.7 g CO 2 /g H 2 produced, primarily based on steam methane reforming (SMR) technology that currently dominates hydrogen production. The substitution of natural gas (NG) and other fossil feedstocks in SMRs with renewable gases may be considered as an option for reducing greenhouse gas emissions. This analysis explores process impacts and constraints associated with the potential introduction of biogenic gases into SMRs. The results indicate that replacing NG in the fuel train of the SMR, followed by partial replacement of NG in the feed train may be a feasible approach. For the CO‐ and CO 2 ‐rich gas compositions assumed in this analysis the results indicate that feed train may accommodate up to 25 mole % of biogenic gases using allowances in existing designs and/or with small modifications, while maintaining similar hydrogen output. NG substitution in higher proportions require more major changes because of increased flow rates and heat exchange requirements in the system. Biogenic gases with lower CO 2 and higher calorific values are advantageous for NG substitution, and dry reforming using the CO 2 present in the feed gas can reduce steam consumption and increase process efficiency within limits where coking does not become a new constraint.

08 HYDROGEN↗

Flame stabilization in DME spray flames under engine-relevant conditions characterized by OH* chemiluminescence and formaldehyde laser-induced fluorescence

The transient and quasi-steady flame structures of Dimethyl Ether (DME) fuel sprays, produced by a single-hole injector (Spray D), were investigated using Planar Laser-Induced Fluorescence (PLIF) and chemiluminescence imaging in a constant-volume chamber under Engine Combustion Network (ECN) Spray A conditions (900 K ambient temperature, 60 bar ambient pressure, 1500 bar injection pressure, and 22.8 kg/m 3 ambient density). Low-temperature chemical reaction zones were visualized using formaldehyde (CH 2 O) PLIF with 355 nm excitation, while high-temperature flame regions were captured via chemiluminescence imaging of excited-state hydroxyl radicals (OH*). Both transient and quasi-steady flame structures clearly show the transition from CH 2 O to OH*, highlighting the progression from low- to high-temperature combustion, while the position of the flame is displaced for DME compared to reference hydrocarbon n-dodecane. Homogeneous reactor calculations with detailed chemistry and using adiabatic mixing for initial temperature show that CH 2 O peaks are significantly higher for DME at the same equivalence ratio, with a higher heat-release during the cool-flame regime with respect to the fuel heating value. Thus, the cool-flame dynamic as a precursor to high-temperature combustion and flame stabilization exhibit distinct behavior for DME relative to conventional hydrocarbons, and these phenomena are effectively resolved through the soot-free nature of DME and the high-speed, time-resolved diagnostics.

CH2O laser-induced fluorescence↗

Liquid rocket combustion instability analysis by CFD methods

Combustion instability in liquid rocket engines is simulated computationally by using a simple two-parameter model for the combustion response function. The objectives of the study are to assess the capabilities of CFD algorithms for instability studies and to investigate the response to parametric effects such as bombs and distributed combustion. Results indicate that numerical solutions of high accuracy can be obtained if a sufficient number of grid points are used per wavelength of the disturbance. The short-term response to bombs or pulses triggers a large number of modes in the combustor whose faithful resolution requires highly dense grids, although there is evidence that correct long-term solutions can be obtained even if all the short-term frequencies are not resolved. Long-term responses to pulses are shown to decay to the most unstable mode in small amplitude cases, and to exhibit limit cycles in large amplitude cases. Comparison of distributed with concentrated heat release indicates the former is more stable for given values of the combustion response parameters, and that the distributed heat release gives rise to higher frequency disturbances. Wave steepening is observed in the solutions, but its effect is less pronounced in multidimensional waves than in one-dimensional waves.

Grenda, J. M.↗

Thermal Insulation System for Large Flame Buckets

The objective of this study is to investigate the use of thermal protection coatings, single tiles, and layered insulation systems to protect the walls of the flame buckets used in the testing of the Space Shuttle Main Engine, while reducing the cost and maintenance of the system. The physical behavior is modeled by a plane wall boundary value problem with a convective frontface condition and a backface condition designed to provide higher heat rates through the material.

Callens, E. Eugene, Jr.↗

Experimental Investigation of Shock-Shock Interactions Over a 2-D Wedge at M=6

The effects of fin-leading-edge radius and sweep angle on peak heating rates due to shock-shock interactions were investigated in the NASA Langley Research Center 20-inch Mach 6 Air Tunnel. The fin model leading edges, which represent cylindrical leading edges or struts on hypersonic vehicles, were varied from 0.25 inches to 0.75 inches in radius. A 9deg wedge generated a planar oblique shock at 16.7deg to the flow that intersected the fin bow shock, producing a shock-shock interaction that impinged on the fin leading edge. The fin angle of attack was varied from 0deg (normal to the free-stream) to 15deg and 25deg swept forward. Global temperature data was obtained from the surface of the fused silica fins through phosphor thermography. Metal oil flow models with the same geometries as the fused silica models were used to visualize the streamline patterns for each angle of attack. High-speed zoom-schlieren videos were recorded to show the features and temporal unsteadiness of the shock-shock interactions. The temperature data were analyzed using one-dimensional semi-infinite as well as one- and two-dimensional finite-volume methods to determine the proper heat transfer analysis approach to minimize errors from lateral heat conduction due to the presence of strong surface temperature gradients induced by the shock interactions. The general trends in the leading-edge heat transfer behavior were similar for the three shock-shock interactions, respectively, between the test articles with varying leading-edge radius. The dimensional peak heat transfer coefficient augmentation increased with decreasing leading-edge radius. The dimensional peak heat transfer output from the two-dimensional code was about 20% higher than the value from a standard, semi-infinite one-dimensional method.

Jones, Michelle L.↗

Thermographic Phosphor Measurements of Shock-Shock Interactions on a Swept Cylinder

The effects of fin leading-edge radius and sweep angle on peak heating rates due to shock-shock interactions were investigated in the NASA Langley Research Center 20-inch Mach 6 Air Tunnel. The fin model leading edges, which represent cylindrical leading edges or struts on hypersonic vehicles, were varied from 0.25 inches to 0.75 inches in radius. A 9deg wedge generated a planar oblique shock at 16.7deg to the flow that intersected the fin bow shock, producing a shock-shock interaction that impinged on the fin leading edge. The fin angle of attack was varied from 0deg (normal to the free-stream) to 15deg and 25deg swept forward. Global temperature data was obtained from the surface of the fused silica fins using phosphor thermography. Metal oil flow models with the same geometries as the fused silica models were used to visualize the streamline patterns for each angle of attack. High-speed zoom-schlieren videos were recorded to show the features and temporal unsteadiness of the shock-shock interactions. The temperature data were analyzed using one-dimensional semi-infinite as well as one- and two-dimensional finite-volume methods to determine the proper heat transfer analysis approach to minimize errors from lateral heat conduction due to the presence of strong surface temperature gradients induced by the shock interactions. The general trends in the leading-edge heat transfer behavior were similar for the three shock-shock interactions, respectively, between the test articles with varying leading-edge radius. The dimensional peak heat transfer coefficient augmentation increased with decreasing leading-edge radius. The dimensional peak heat transfer output from the two-dimensional code was about 20% higher than the value from a standard, semi-infinite onedimensional method.

Jones, Michelle L.↗

Global Aeroheating Measurements of Shock-Shock Interactions on a Swept Cylinder

The effects of fin leading-edge radius and sweep angle on peak heating rates due to shock-shock interactions were investigated in the NASA Langley Research Center 20-Inch Mach 6 Air Tunnel. The cylindrical leading-edge fin models, with radii varied from 0.25 to 0.75 inches, represent wings or struts on hypersonic vehicles. A 9deg wedge generated a planar oblique shock at 16.7deg. to the flow that intersected the fin bow shock, producing a shock-shock interaction that impinged on the fin leading edge. The fin sweep angle was varied from 0deg (normal to the free-stream) to 15deg and 25deg swept forward. These cases were chosen to explore three characterized shock-shock interaction types. Global temperature data were obtained from the surface of the fused silica fins using phosphor thermography. Metal oil flow models with the same geometries as the fused silica models were used to visualize the streamline patterns for each angle of attack. High-speed zoom-schlieren videos were recorded to show the features and any temporal unsteadiness of the shock-shock interactions. The temperature data were analyzed using a one-dimensional semi-infinite method, as well as one- and two-dimensional finite-volume methods. These results were compared to determine the proper heat transfer analysis approach to minimize errors from lateral heat conduction due to the presence of strong surface temperature gradients induced by the shock interactions. The general trends in the leading-edge heat transfer behavior were similar for each explored shock-shock interaction type regardless of the leading-edge radius. However, the dimensional peak heat transfer coefficient augmentation increased with decreasing leading-edge radius. The dimensional peak heat transfer output from the two-dimensional code was about 20% higher than the value from a standard, semi-infinite one-dimensional method.

Mason, Michelle L.↗

Heterogeneity of Bulk Oxygen Isotopic Compositions in Anhydrous Interplanetary Dust Particles

Introduction: Anhydrous interplanetary dust particles are one of the least altered ancient solar systemmaterials. Their bulk chemical compositions match those of CI chondrites within a factor of 2-3, except for carbonwhich is enriched in both anhydrous and hydrated IDPs by ~4x CI [1]. Hydrous IDPs often show 16O-poor isotopiccompositions, likely due to the interaction with isotopically heavy H2O [2]. Anhydrous IDPs are interpreted tooriginate from comets from the outer solar system [3]. Oxygen isotopic data for these materials is scarce, but resultspoint to a wider range of compositions [4]. This heterogeneity might be a result of mixing between a 16O-rich and a16O-poor reservoir formed via self-shielding and photodissociation of CO [5]. Here, we report bulk oxygen isotopiccompositions of three anhydrous IDPs in context of their mineralogical composition and discuss possible origins ofisotopic heterogeneity. Experimental: Bulk chemical composition and mineralogy of 70 nm thin ultramicrotomed sections of threeanhydrous IDPs (L2099A7, L2099A8, and L2071AB1) were analyzed using a Thermo Scientific Titan Themis G360-300 TEM equipped with a four-quadrant energy-dispersive X-ray detector (Super-X G2) at University ofMünster. Bulk oxygen isotopic compositions were measured using a NanoSIMS 50 at the Max-Planck-Institut fürChemie in Mainz. A focused Cs+ ion beam (~1 pA, ~100 nm) was rastered over a field of view varying from 5 x 5 to6 x 6 μm2, depending on particle size for 15 layers. Negative secondary ions of 16O, 17O, 18O, 12C14N, and 28Si werecollected on electron multipliers. The 16OH contribution to the 17O peak was 1-2 ‰. As a standard, a matrix regionof meteorite CR2 Queen Alexandra Range (QUE) 99177 was used, whose oxygen isotopic composition wasmeasured by [6]. Results and Discussion: Particles A7 and A8 are both fine-grained, consisting mostly of small, 100 nm-sizedequilibrated aggregates (EA). Both particles exhibit discontinuous magnetite rims with thicknesses up to 50 nm inA7 and 100 nm in A8 on the outsides. In Particle AB1, the upper part of the particle consists of a few EAs, while thelower part contains lots of small GEMS grains with 100-200 nm diameter clustered together. Magnetite rims arenearly absent, the rare rims reaching maximum 20 nm thickness, indicating that AB1 is of more primitive naturethan the other two IDPs [1]. Furthermore, it contains several diffuse GEMS-like areas, identified by an amorphoussilicate groundmass with small nano-inclusions of Fe,Ni-metal and Fe-sulfides. All three particles are subsolar forall major element/Si ratios. Mean S/Si of particles A7 and A8 is 0.046 and 0.048, respectively, while it is an order ofmagnitude higher in AB1 (0.184). This reflects the higher degree of thermal alteration in A7 and A8, resulting in theloss of volatile S and oxidation of Fe-sulfides and FeNi-metal to magnetite as present in particle rims. A8 is rather16O-poor with δ17OSMOW = 7.8 ± 3.4 ‰ and δ18OSMOW = 9.5 ± 3.1 ‰ (1σ), followed by A7 with δ17OSMOW = − 0.8 ±4.6 ‰ and δ18OSMOW = −2.2 ± 3.4 ‰. In contrast to that, AB1 has the most 16O-rich bulk composition with δ17OSMOW= −24.2 ± 5.4 ‰ and δ18OSMOW = −25.3 ± 3.6 ‰. All investigated IDPs plot slightly above the CCAM line aspreviously reported for other anhydrous IDPs [4], maybe due to a contribution from circumstellar dust from AGBstars enriched in 17O [7]. The 16O-rich composition of AB1 is similar to the most 16O-rich anhydrous IDP U2015D21measured by [8] which is dominated by GEMS [9] and the GEMS-rich IDP GM4-2 reported by [10]. Nevertheless,it is unlikely that GEMS are the carrier for the 16O-rich composition of AB1 because most GEMS have O isotopiccompositions indistinguishable from terrestrial values, although errors on these analyses are large [11]. The isotopicheterogeneity is best explained by contribution of grains from different regions in the protoplanetary disk, samplingdifferent O isotope reservoirs, created by self-shielding and photodissociation of CO. This process resulted in 16O-rich CO gas and 16O-poor H2O that froze as ice-mantles onto dust grains [12]. Alternatively, the higher degree ofheating in A7 and A8 could have influenced isotopic fractionation, because higher δ17,18O values are reported fromthe regions of the atmosphere where small particles are heated and oxidized, as observed for the thermal alteration ofcosmic spherules [13]. Acknowledgements: We would like to thank NASA Astromaterials Acquisition & Curation Office for providing IDPsamples and DFG for funding this project (VO1816/5-1)

B Schulz↗

Optimization of Operating Profit for the FEED of the PZAS Process for CO 2 Capture on a 460 MW NGCC

A rating model of PZAS (Piperazine with the Advanced Stripper) for a 460 MW natural gas combined cycle was developed from vendor-provided equipment performance data. Surrogate rating models were built and used to optimize variable profit of the system subject to natural gas and electricity price at a fixed value for CO 2 of $\$80$/tonne. Several process constraints were considered between ambient temperatures of 4.4 and 40.5 °C. Lower lean loading resulted in lower reboiler heat duty of about 2.2 GJ/tonne. Lean loading at 0.2 mol/equiv N was sufficient at an ambient temperature of 4.4 °C to maximize variable profit. Solvent precipitation was avoided even at low lean loading (0.18 mol/mol) in the absence of a trim cooler for the lean solvent between the absorber and the cold cross exchanger. Optimal CO 2 removal was always higher than the design case removal of 90% and achieved a peak of 93.6% for 4.4 ºC ambient temperature. Lean solvent rate was a significant driver of profitability. The maximum capacity of the compressor was a significant constraint on profitability. Increasing compressor capacity by 20–30% could increase variable profit by about 21% in the case of 0.18 lean loading at 4.4 °C ambient temperature. Furthermore, this increase in profit was lower at higher ambient temperature and higher lean loading. The breakeven gas price was $\$4.6$/MMBtu at high lean loading of 0.22 mol/mol. Below this value, profit was maximized by increasing the boiler heat rate. Above this value, profit could not be increased by burning additional natural gas, requiring a reduction in boiler heat rate and consequently, specific heat duty. At lower lean loading (0.2, 0.18 mol/mol), this transition in heat duty was not observed due to the lower heat duty. As the ambient temperature increased, a similar trend in heat duty was observed at 0.22 lean loading, but the transition to lower heat duty occurred earlier at $\$4$/MMBtu. This was because of the lower CO 2 production at higher ambient temperature, making the process unprofitable at a gas price higher than $\$3$/MMBtu unless the heat duty of the stripper and natural gas boiler is steeply decreased.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Radiative Heat Transport and Optical Characterization of High Temperature Molten Salts

The goal of this project was to advance the field of molten fluoride radiative heat transfer (RHT), through optical property measurements, heat transfer loop construction and operation, and computational fluid dynamics simulations. The following outcomes have been accomplished. A comprehensive review has been conducted to compile all available RHT-relevant optical absorption data for molten fluorides. The various measurement methods have also been compiled and critiqued. Thermal emission measurement methods have been refined and documented. A unique thermal emissivity measurement facility has been constructed and used to measure the emissivity of flowing FLiBe-exposed SS316 samples. A slight increase has been observed in the emissivity compared to unexposed SS316. A dual reflectance-emission setup was partially demonstrated for the purpose of molten fluoride absorption measurement. Preliminary infrared edge data for FLiNaK was obtained. A visible near-infrared (NIR) measurement setup has been constructed and will be used to measure absorption of corrosion products in FLiBe. A new multi-band thermal radiation method using blackbody-weighted spectral bands for the absorption-coefficient was deployed to investigate the thermal performance of the UW Natural Circulation FLiBe Loop under various power levels and operating conditions. The results showed an increasing and decreasing trend in the overall heat transfer with optical thickness with a maximum at optical thickness τ D ≈Ο(1). A forced convection FLiBe loop was constructed for the purpose of studying corrosion and thermal hydraulic phenomena. A vertical cantilever pump is used to achieve up to 5 gpm and 5 m/s flow velocity in hot and cold test sections. A methodology has been established for modeling radiative heat transfer (RHT) in molten salt coolants for the purpose of quantifying the contribution of thermal radiation in conditions relevant to FHR or MSR systems. The comparison between the results obtained for forced and mixed convection showed that in the studied ranges of optical thickness, the maximum effect of RHT on overall heat transfer was 60% improvement observed at z/D = 250 for forced convection; whereas for mixed convection, that value was higher at 170% observed at z/D = 30. The highest effect of RHT on the overall energy distribution was observed at τ D ≈3.4. Negligible effect (<20%) was observed above τ D =18 and below τ D ≈0.002. A CFD code-to-code comparison was conducted using COMSOL Multiphysics at UW-Madison and STAR-CCM at MIT, for a forced and mixed convection laminar flow for a grey medium in a vertical heated using both COMSOL Multiphysics at UW-Madison and STAR-CCM at MIT. The relative error was the largest at τ D =40 for the radiative heat flux, bulk temperature, and Nusselt number. On the other hand, the relative error was the least at τ D =0.002 for the conductive heat flux, bulk temperature, and Nusselt number.

Anderson, Mark↗

Validation of the HyRAM+ physics models for use with propane

The Hydrogen Risk Assessment Model Plus (HyRAM+) toolkit combines quantitative risk assessment with simulations of unignited dispersion, ignited turbulent diffusion flames, and indoor accumulation with delayed ignition of fuels. HyRAM+ is differentiated from HyRAM in that it includes models and leak data for other alternate fuels. The models of the physical phenomena need to be validated for each of the fuels in the toolkit. This report shows the validation for propane which is being used as a surrogate for autogas, which is a mixture of propane and butane and used in internal combustion engines in vehicles. For flame length comparisons, five previously published experiments from peer reviewed journals were used to validate our models. The validation looked at flame lengths and flame widths with respect to different leak diameters, mass flow rates, and source pressures. Most of the sources included more than one set of experimental data, which were collected using different methods (CCD cameras, IR visualization etc.). In general, HyRAM+ overpredicts the flame lengths by around 65%. For heat and radiation models, we compared the heat flux and radiation data reported from two different sources to the values calculated by HyRAM+. For higher mass flow rates, the HyRAM+ calculated flame length results gave a better estimate of what is found in the experiments (65% error), but a higher error (85%) is observed between the HyRAM+ calculated lengths and the experimental flame lengthsfor lower mass flows. Some differences can be attributed to outdoor environmental effects (i.e. wind speed) and uncertainties in jet flame shapes. The propane flame trajectory is predicted for a high Reynolds number case with Re = 12,500 and a low Reynolds number case where Re = 2,000. The Re=12,500 case which is momentum dominated matches well with the experimental flame trajectory, but the agreement for the bouancy driven low Reynolds number case is not as good. Dispersion modeling for unignited propane was also analyzed. We compared the mole fraction, mixture fraction, mean velocity, concentration half width, and inverse mass concentration over an axial distance from different credible journals to the values calculated by HyRAM+. The results display good agreement but generally, HyRAM+ predicts a wider profile for mole fraction and mixture fraction experiments. Overall, HyRAM+’s results are reasonable for predicting the flame length, heat flux, flame trajectory, and dispersion for propane and can be used in risk analyses

08 HYDROGEN↗

Gasoline Engine and Fuels Offering Reduced Fuel Consumption and Emissions: Vehicle Modeling Final Report

The Gasoline Engine and Fuels Offering Reduced Fuel Consumption and Emissions (GEFORCE) project was proposed in response to the U.S. Department of Energy’s Funding Opportunity Announcement 0991 by a team made up of the members of the Coordinating Research Council (CRC) and the research staff at Oak Ridge National Laboratory (ORNL.) The project focused on investigating the potential benefits that might be attained through synergistic use of specific engine technology together with fuels formulated to represent potential directions that high-octane fuels of the future might progress. A stated objective in the DOE FOA was to demonstrate a 25% reduction in petroleum consumption through optimization of the engine technologies together with a suitable fuel. An advanced engine was constructed and used with a matrix of research fuels to investigate potential avenues for efficiency improvement. The engine incorporated technologies expected to become mainstream for boosted engines in the next 10 to 20 years. These included increased compression ratio, a two-stage turbocharger, and cooled external exhaust gas recirculation (EGR). The fuel matrix was designed to investigate impacts from research octane number (RON), volumetric ethanol content, and the final boiling point of the fuel. The engine calibration was optimized for each fuel individually and data collected to enable vehicle system modelling that projected energy consumption, fuel economy, tailpipe CO₂ emissions, and impact on petroleum consumption for an industry-average mid-size sedan. The engine calibration and data collection were carried out at IAV in Michigan and is the subject of a separate report. IAV provided the engine data to Oak Ridge National Laboratory to support the vehicle modelling portion of the project. The vehicle modelling results show the following trends: Ethanol content does have a consistently strong influence on the fuel economy results for all cycles and all fuels. Among the fuels of a nominal RON level, increasing ethanol content consistently lowers fuel economy, with the 30% ethanol fuels always providing the lowest fuel economy for a given RON level. However, in some cases the energy consumption improvement allows the 30% ethanol fuels to match the fuel economy of the ethanol-free fuel P. These observations underscore the importance of both engine efficiency and fuel volumetric energy content on vehicle fuel economy.; There was no consistent trend in the projected energy consumption results for differences in fuel T90 for all fuels and cycles. Fuel economy projections did show a consistent trend, with the higher T90 fuel providing slightly greater fuel economy when compared to the low T90 fuel of the same ethanol content. The observed trends were consistent with differences in the heating value of the fuels.; The 102-RON fuels provided reduced energy consumption and greater fuel economy for the advanced engine on all drive cycles. The engine compression ratio of 11.5 was higher than would typically be used in a turbocharged engine when 92-RON fuel use is expected. Hence, the engine experiences more efficiency degradation from knock avoidance when using the 92-RON fuels. This degradation causes the fuel economy results for the 92-RON fuels to be lower than those for the 102-RON fuels.; Fuels E and F (92-RON, 30% ethanol) are projected to achieve 10% or greater reduction in petroleum consumption, with fuels K (102-RON, 30% ethanol) and O (97 RON, 30% ethanol) achieving greater than a 20% reduction. Fuel L (102-RON, 30% ethanol) achieves greater than 25% reduction, meeting the petroleum reduction target of the project. All of the fuels that achieve 10% or greater reduction in petroleum consumption are 30% ethanol blends.; Increasing final boiling point increased fuel economy at fixed ethanol content when the 102-RON fuels were used. This trend is a result of differences in the volumetric energy content of the fuels and the projected energy consumption values for the fuels. In the case of the 102-RON fuels, increasing final boiling point also resulted in an increase in the energy content of the fuel. There was not a consistent trend between the energy content and final boiling point for the 92-RON fuels at fixed ethanol content.

33 ADVANCED PROPULSION SYSTEMS↗

Thermoelectric properties of Nb3SbxTe7-x compounds

Niobium antimony telluride, Nb3Sbx,Te7-x, was synthesized and tested for thermoelectric properties in the Thermoelectrics group at the Jet Propulsion Laboratory. The forty atoms per unit cell of Nb3Sb2Te5 and its varied mixture of atoms yield acomplicated structure, suggesting that Nb3Sb2Te5 and related compounds may exhibit low thermal conductivity and hence a higher ZT value. Nb3SbxTe7-x, compounds were synthesized and subsequently analyzed for their Seebeck voltage, heat conduction, and electrical resistivity. Results indicate that Nb3Sb2Te5 is a heavily doped semiconductor whose thermoelectric properties are compromised by compensating n-type and p-type carriers. Attempts to dope in favor of either carrier by varying the Sb:Te ratio yielded samples containing secondary metallic phases that dominated the transport properties of the resulting compounds.

thermoelectric power generation segmented↗

Urban Versus Lake Impacts on Heat Stress and Its Disparities in a Shoreline City

Abstract Shoreline cities are influenced by both urban‐scale processes and land‐water interactions, with consequences on heat exposure and its disparities. Heat exposure studies over these cities have focused on air and skin temperature, even though moisture advection from water bodies can also modulate heat stress. Here, using an ensemble of model simulations covering Chicago, we find that Lake Michigan strongly reduces heat exposure (2.75°C reduction in maximum average air temperature in Chicago) and heat stress (maximum average wet bulb globe temperature reduced by 0.86°C) during the day, while urbanization enhances them at night (2.75 and 1.57°C increases in minimum average air and wet bulb globe temperature, respectively). We also demonstrate that urban and lake impacts on temperature (particularly skin temperature), including their extremes, and lake‐to‐land gradients, are stronger than the corresponding impacts on heat stress, partly due to humidity‐related feedback. Likewise, environmental disparities across community areas in Chicago seen for skin temperature are much higher (1.29°C increase for maximum average values per $10,000 higher median income per capita) than disparities in air temperature (0.50°C increase) and wet bulb globe temperature (0.23°C increase). The results call for consistent use of physiologically relevant heat exposure metrics to accurately capture the public health implications of urbanization.

54 ENVIRONMENTAL SCIENCES↗

A Comparison of Theory and Experiment for High-speed Free-molecule Flow

A comparison is made of free-molecule-flow theory with the results of wind-tunnel tests performed to determine the drag and temperature-rise characteristics of a transverse circular cylinder. The measured values of the cylinder center-point temperature confirmed the salient point of the heat-transfer analysis which was the prediction that an insulated cylinder would attain a temperature higher than the stagnation temperature of the stream. Good agreement was obtained between the theoretical and the experimental values for the drag coefficient.

Stalder, Jackson R↗

Electric current-induced precipitation hardening in advanced high-strength steel

Effect of electric current on precipitation hardening for advanced high-strength steel is investigated based on mechanical testing and microscopic observation. Complex-phase steel containing nano-sized Nb-bearing carbides was used. By comparing the flow stress between uniaxial tension with applied electric current (pulsed tension) and without electric current (nonpulsed tension) at various elevated temperatures, the influence of electric current on precipitation hardening was confirmed. A higher values of Vickers hardness and full-width-at-half-maximum were obtained in the pulsed tensile specimen compared to the identically heat treated specimen after the same deformation. Small angle neutron scattering analysis showed that the volume fraction and mean diameter of newly formed precipitates in the pulsed tensile specimen were higher and larger than those in the induction heat treated specimen, respectively. In conclusion, it clearly shows that additional precipitation hardening could be induced by the athermal effect of electric current, which is distinct from the thermal effect of Joule heating.

36 MATERIALS SCIENCE↗

Iodine capture with mechanically robust heat-treated Ag-Al-Si-O xerogel sorbents

Silver-loaded heat-treated aluminosilicate xerogels (Ag-HTX) were evaluated as sorbents for iodine [I2(g)] capture. The heat treatment step was performed to help increase the mechanical integrity of the gels. The synthesized xerogels were characterized using powder X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray spectroscopy, transmission electron microscopy, Brunauer-Emmett-Teller analysis, gravimetric iodine loading, nanoindentation, and dynamic mechanical analysis. The structural and chemical analyses of Ag-HTX showed uniform distribution of Ag throughout the gel network after Ag-exchange. After I2(g) capture, the AgI crystallites were observed in the sorbent verifying chemisorption as the iodine capture mechanism. Iodine loading of this xerogel was 0.43 g g-1 at 150°C over 1 d and 0.52 g g-1 at 22°C over 33 d. The specific surface area of Ag-HTX was 202 m2 g-1 and decreased to 87 m2 g-1 after iodine loading. The hardness of the heat-treated xerogel was 160 times higher than heat-treated aerogel of the same composition. The heat-treatment process increased the modulus value to 40.77 MPa from 6.99 MPa of as-made xerogel, demonstrating the need for this added step in the synthesis process. These results show that Ag-HTX is a promising sorbent for I2(g) capture with good loading capacity and mechanical stability.

xerogels, aerogels, iodine capture, hardness testi↗