Search NASA⌕ Search

SEARCH · Search NASA

Results for “hot”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Evaluation of measuring thermal conductivity of isotropic and anisotropic thermally insulating materials by transient plane source (Hot Disk) technique

The transient plane source (TPS) technique, also referred as the Hot Disk method, has been widely used due to its ability to measure the thermal properties of an extensive range of materials (solids, liquids, and powder). Recently, it has been recognized that typical Hot Disk sensors can influence TPS results of thermally insulating materials and lead to an overestimation of thermal conductivity. Although improvements have been proposed, they have not yet been implemented in the commercial TPS, leaving researchers with non-standardized modifications or options provided by a commercial Hot Disk apparatus. An empirical study of thermally insulating materials such as extruded polystyrene (XPS) and aerogel blanket is conducted in order to address the factors that affect the reliability of thermal conductivity k obtained using the commercial TPS apparatus. Sensor size, input power, duration of the measurements, applied pressure, and, in the case of anisotropic materials, heat capacity are investigated, and the results are compared with those using a Heat Flow Meter apparatus. The effect of sensor size on the k value is ascribed to heat loss through connecting leads and is more pronounced in smaller sensors and in materials with lower k values . In the case of XPS and aerogel, the effect becomes minimal for sensors with a radius r ≥ 6.4 mm. The low input power yields a high scattering of the results and should be avoided. Applied contact pressure and the tested region of the specimen play an important role in experiments with low-density fibrous materials due to the large percentage of heat being transferred by radiation and the heterogeneous nature of the samples, respectively. Additionally, the sensitivity of anisotropic measurements to the value of the material’s volumetric heat capacity ( ρC p ) is shown, emphasizing the need for the precise determination.

thermal conductivity↗
DOE OSTI2022

On the hot surface ignition of a wall-stagnating spray flame

The ignition of fuel sprays due to interaction with hot surfaces is an important phenomenon in the safety analysis of many engineering systems. We perform a parametric study of the hot surface ignition (HSI) of a fuel spray approaching a heated surface caused by the accidental leakage of a fuel line. Here, to this end, we employ a one-dimensional Eulerian-Eulerian formulation with a non-equilibrium evaporation model and a realistic chemical mechanism to describe $n$-dodecane fuel chemistry. We first describe and analyze the phenomenology of the unsteady processes leading to ignition using non-dimensionalized quantities. Through consideration of the temporal development of the most reactive mixture, we demonstrate that ignition occurs at a fuel-lean composition in a premixed region near the hot surface. Using non-dimensional parameters identified from the governing equations, we perform a parametric study of the time, location and local mixture composition at ignition and determine the ignition limits. We then identify the most important parametric sensitivities for physical analysis using a data-driven classification method. Our analysis demonstrates a contraction of the ignition limits with increased Stokes number and a regime of parametric insensitivity of igniting mixture composition. We also show that at high Damköhler numbers, the ignition location conforms to the parametric behavior of the thermal boundary layer, whereas at low Damköhler numbers approaching the ignition limit it reaches a near-unity value of the quenching Peclet number. We then compare the demonstrated parametric dependencies to the results of the quasi-steady asymptotic ignition literature, showing that our results are consistent with those obtained analytically within the limitations imposed by the simplified formulation of the latter.

42 ENGINEERING↗
DOE OSTI2025

Effect of MgSO 4 addition on alkali sulphates induced hot corrosion of a β-NiAl coating

The effect of MgSO 4 addition on alkali sulphates induced hot corrosion of a β-NiAl coating was studied by performing a series of tests with deposits of Na 2 SO 4 , Na 2 SO 4 -20 %K 2 SO 4 and Na 2 SO 4 -12 %K 2 SO 4 -35 %MgSO 4 (mol.% for all) at 700 °C in air with addition of SO 2 . For elucidating the observed corrosion phenomena, various salt-oxide/NiAl powder mixtures were exposed to the same hot corrosion test conditions. Two pseudo-binary phase diagrams of the Na, K, Mg-sulphate systems were calculated using an in-house developed thermodynamic database. Addition of MgSO 4 to Na 2 SO 4 -20 %K 2 SO 4 deposit salt inhibited the hot corrosion attack during 24 h exposure, which is related to consumption of aggressive K 2 SO 4 by the formation of solid K 2 Mg 2 (SO 4 ) 3 . However, extending the exposure with Na 2 SO 4 -12 %K 2 SO 4 -35 %MgSO 4 deposit to 100 h resulted in severe corrosion attack. The latter observation is explained by a reaction between K 2 Mg 2 (SO 4 ) 3 and NiAl causing formation of a Mg, Ni and Al containing spinel accompanied by release of the aggressive K 2 SO 4 into the liquid phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

The impact of hot-press conditions on the durability of polymer electrolyte membrane fuel cells

The proton exchange membrane integrity can be compromised during hot-press fabrication of membrane electrode assemblies (MEAs) causing premature cell failures during operation. In this work, infrared (IR) thermography was used as a diagnostic tool to spatially visualize hydrogen (H 2 ) crossover and identify process-induced-membrane irregularities (PIMs). These irregularities were identified as seed locations for MEA failures. Fine tuning of hot-press conditions was used to mitigate premature cell failures informed by accelerated stress testing (AST). The impact of PIMs on the initial performance, high-frequency resistances, open-circuit voltage, and H 2 crossover are reported. Nafion XL and 212 membranes, hot-pressed with a force of 16 kg/cm 2 and temperature of 120°C, were found to be consistently irregularity-free. Irregularity-free MEAs using Nafion 211, 212, and XL membranes demonstrated AST lifetime improvements of 58, 64 and 400%, respectively, compared to those fabricated with non-optimized conditions. In conclusion, this work highlights the importance of fabrication parameters on premature cell failures.

08 HYDROGEN↗
DOE OSTI2023

Energy-Resolved Femtosecond Hot Electron Dynamics in Single Plasmonic Nanoparticles

Efficient excitation and harvesting of hot carriers from nanoscale metals is central to many emerging photochemical, photovoltaic, and ultrafast optoelectronic applications. Nevertheless, direct experimental evidence of the energy-dependent femtosecond dynamics in ubiquitous tens-of-nanometer gold structures remains elusive, despite the potentially rich interplay between interfacial and internal plasmonic fields, excitation distributions, and scattering processes. To explore the effects of nanoscale structure on these dynamics, we employ simultaneous time-, angle-, and energy-resolved photoemission spectroscopy of single plasmonic nanoparticles. Photoelectron velocity and electric field distributions reveal bulk-like ballistic hot electron transport in different geometries, lacking any signatures of surface effects. Energy-resolved dynamics are measured in the 1–2 eV range and extrapolated to lower energies via Boltzmann theory, providing a detailed view of hot electron lifetimes within nanoscale gold. Here, we find that particles with relevant dimensions as small as 10 nm serve as exemplary platforms for studying intrinsic metal dynamics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Hot-carrier dynamics in InAs/AlAsSb multiple-quantum wells

A type-II InAs/AlAs 0.16 Sb 0.84 multiple-quantum well sample is investigated for the photoexcited carrier dynamics as a function of excitation photon energy and lattice temperature. Time-resolved measurements are performed using a near-infrared pump pulse, with photon energies near to and above the band gap, probed with a terahertz probe pulse. The transient terahertz absorption is characterized by a multi-rise, multi-decay function that captures long-lived decay times and a metastable state for an excess-photon energy of >100 meV. For sufficient excess-photon energy, excitation of the metastable state is followed by a transition to the long-lived states. Excitation dependence of the long-lived states map onto a nearly-direct band gap (E g ) density of states with an Urbach tail below E g . As temperature increases, the long-lived decay times increase < E g , due to the increased phonon interaction of the unintentional defect states, and by phonon stabilization of the hot carriers > E g . Additionally, Auger (and/or trap-assisted Auger) scattering above the onset of the plateau may also contribute to longer hot-carrier lifetimes. Meanwhile, the initial decay component shows strong dependence on excitation energy and temperature, reflecting the complicated initial transfer of energy between valence-band and defect states, indicating methods to further prolong hot carriers for technological applications.

14 SOLAR ENERGY↗
DOE OSTI2021

Hot carrier relaxation and inhibited thermalization in superlattice heterostructures: The potential for phonon management

One of the main loss mechanisms in photovoltaic solar cells is the thermalization of photogenerated hot carriers via phonon-mediated relaxation. By inhibiting these relaxation mechanisms and reducing thermalization losses, it may be possible to improve the power conversion efficiency of solar cells beyond the single gap limit. Here, type-II InAs/AlAsSb multi-quantum well (MQW) structures are investigated to study the impact of the phononic properties of the AlAsSb barrier material in hot carrier thermalization. Experimental and theoretical results show that by increasing the barrier thickness (increasing the relative contribution of AlAsSb content in the superlattices), the relaxation of hot carriers is reduced as observed in power-dependent photoluminescence and thermalization analysis. Furthermore, this is attributed to an increase in the phononic bandgap of the MQW with increasing AlAsSb composition reducing the efficiency of the dominant Klemens mechanism as the phononic properties shift toward a more AlSb-like behavior.

14 SOLAR ENERGY↗
DOE OSTI2023

Hot carrier extraction from 2D semiconductor photoelectrodes

Hot carrier-based energy conversion systems could double the efficiency of conventional solar energy technology or drive photochemical reactions that would not be possible using fully thermalized, “cool” carriers, but current strategies require expensive multijunction architectures. Using an unprecedented combination of photoelectrochemical and in situ transient absorption spectroscopy measurements, we demonstrate ultrafast (<50 fs) hot exciton and free carrier extraction under applied bias in a proof-of-concept photoelectrochemical solar cell made from earth-abundant and potentially inexpensive monolayer (ML) MoS 2 . Our approach facilitates ultrathin 7 Å charge transport distances over 1 cm 2 areas by intimately coupling ML-MoS 2 to an electron-selective solid contact and a hole-selective electrolyte contact. Our theoretical investigations of the spatial distribution of exciton states suggest greater electronic coupling between hot exciton states located on peripheral S atoms and neighboring contacts likely facilitates ultrafast charge transfer. Our work delineates future two-dimensional (2D) semiconductor design strategies for practical implementation in ultrathin photovoltaic and solar fuel applications.

2D materials↗
DOE OSTI2024

Probing and Understanding the Spatial and Energy Distributions of Plasmonic Hot Carriers via Single-Molecule Quantum Transport

The generation of hot carriers in plasmonic nanostructures offers new transformative opportunities for a range of applications, including solar energy harvesting, photochemistry, and photodetection. To better understand such phenomena, this project aims to develop an experimental approach to study and understand hot carrier distributions in photoexcited plasmonic nanostructures. The developed experimental approach, combining scanning probe-based single-molecule quantum transport measurements with plasmonic excitation methods, leverages nanoscopic single molecules as quantum energy filters to selectively access hot carriers in a variety of plasmonic nanostructures. This report summarizes the key outcomes, impacts, and lessons learned in the first two years of the project. Over the past two years, important progress was made in achieving the project's goals, including the development of the scanning probe-based experimental platform, fabrication of plasmonic nanostructures, and design and synthesis of the desired molecular candidates. Insights from this research will pave the path toward the development of technologies that will improve the way we harvest solar energy and drive chemical reactions and ultimately help transition the U.S. to a clean and sustainable society.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Advanced HVAC Humidity Control for Hot-Humid Climates

During this project we develop and validate a cost-effective, integrated control solution to improve humidity control and comfort for energy-efficient homes in hot-humid climates. This study focuses on developing a strategy that is effective, field tested, and practical for builders to install with minimal disruption to standard practices. A successful solution would simplify the transition to high-performance humidity control and be the basis for design and installation guidance. By relying on the central system as a starting point, the strategy employed minimizes system complexity and cost for builders, while improving comfort and operating cost for homeowners. The solution strategy was to coordinate the cooling, dehumidification, and ventilation functions of central, ducted HVAC systems to better control indoor humidity, improve occupant thermal comfort, and capture energy savings. The primary strategic goals were to: (1) optimize dehumidification by the central air-conditioning system, particularly during part-load conditions, using conventional equipment with modified control settings and lower system airflows; (2) maximize ventilation during heating/cooling on-cycles, to “bank” and condition outdoor ventilation air, and minimize ventilation during off-cycles; (3) quantify the effectiveness and energy impact of the dehumidification and ventilation strategies, while identifying a metric that would be useful to evaluate latent effectiveness. For the test houses in our study, located in Richmond Hill, Georgia; Houston, Texas; and Monroe, Louisiana we observed: (1) the indoor humidity did not exceed 60% RH during the monitored cooling season for 99% of the time in Richmond Hill, 96% of the time in Houston, and 90% of the time in Monroe; (2) the dehumidification strategy improved the steady-state latent capacity of the HVAC system at design conditions by 16% to 49% at the Houston test house and by 28% to 71% at the Monroe test house, depending on which mode the system was operating in; and (3) the good results at the test houses were primarily due to the amount of time the air-conditioning system operated in ramping or dehumidification modes, or both, particularly during the early cooling season. This study demonstrates that air conditioners or heat pumps with a single-stage compressor can provide good humidity control without the need for a two-stage or variable-stage compressor system. The airflow and control settings for ramping and dehumidification modes are critical to control indoor humidity in hot-humid climates, particularly during part-load and shoulder season conditions. The dehumidification strategy used in this study did not jeopardize the mechanical reliability of the cooling equipment. The strategies used in this study are applicable across various equipment brands, models, and efficiency levels, and also applicable to a broad range of homes in hot-humid climates. Results will vary by specific equipment, location, and house configuration and construction.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

Moisture Performance of Unvented Attics With Vapor Diffusion Ports and Buried Ducts in Hot, Humid Climates

Energy efficiency measures, such as cool roofs, radiant barriers, interior radiative control coatings, and buried ducts are increasing in popularity and are promoted by energy codes because of their energy-saving potential. However, these strategies can also pose moisture risks in attics by lowering surface temperatures and increasing condensation potential and moisture accumulation. Of particular concern in hot-humid climates is dripping condensation on cold air-conditioning ductwork in the summer - commonly referred to as duct "sweating" - which threatens the attic floor with conditions conducive to mold growth and rot. One strategy to mitigate these moisture issues is to wrap ductwork in thicker duct-wrap insulation with an integrated exterior vapor barrier, but thick duct wrap can be difficult to come by, expensive, and unwieldy to work with. This study explores an alternative strategy of reducing moisture issues while embracing energy efficiency by using unvented attics with vapor diffusion ports and buried ductwork in hot-humid climates. Vapor diffusion ports have been studied so far in a wide range of U.S. climates, mostly in the context of conditioned attics. In this study, the strategy is implemented in the novel context of hot-humid climates with ductwork sitting atop blown-in attic floor insulation in unconditioned attics. Using a combination of field experiments and hygrothermal modeling, the findings of this project indicate that an unvented attic with vapor diffusion ports and buried ducts may be a key part of a successful low-cost method for reducing the attic moisture load by venting excess moisture out of the attic, keeping duct-jacket surfaces above dew point temperature, and keeping the roof deck safe from winter moisture accumulation.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Comparative Analysis of Microbial Diversity Across Temperature Gradients in Hot Springs From Yellowstone and Iceland

Geothermal hot springs are a natural setting to study microbial adaptation to a wide range of temperatures reaching up to boiling. Temperature gradients lead to distinct microbial communities that inhabit their optimum niches. We sampled three alkaline, high temperature (80–100°C) hot springs in Yellowstone and Iceland that had cooling outflows and whose microbial communities had not been studied previously. The microbial composition in sediments and mats was determined by DNA sequencing of rRNA gene amplicons. Over three dozen phyla of Archaea and Bacteria were identified, representing over 1700 distinct organisms. We observed a significant non-linear reduction in the number of microbial taxa as the temperature increased from warm (38°C) to boiling. At high taxonomic levels, the community structure was similar between the Yellowstone and Iceland hot springs. We identified potential endemism at the genus level, especially in thermophilic phototrophs, which may have been potentially driven by distinct environmental conditions and dispersal limitations.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Giant Outer Transiting Exoplanet Mass (GOT ‘EM) Survey. II. Discovery of a Failed Hot Jupiter on a 2.7 Yr, Highly Eccentric Orbit

Radial velocity (RV) surveys have discovered giant exoplanets on au-scale orbits with a broad distribution of eccentricities. Those with the most eccentric orbits are valuable laboratories for testing theories of high-eccentricity migration. However, few such exoplanets transit their host stars, thus removing the ability to apply constraints on formation from their bulk internal compositions. We report the discovery of Kepler-1704 b, a transiting 4.15 M {sub J} giant planet on a 988.88 day orbit with an extreme eccentricity of 0.921{sub -0.015}{sup +0.010}. Our decade-long RV baseline from the Keck I telescope allows us to measure the orbit and bulk heavy-element composition of Kepler-1704 b and place limits on the existence of undiscovered companions. A failed hot Jupiter, Kepler-1704 b was likely excited to high eccentricity by scattering events that possibly began during its gas accretion phase. Its final periastron distance was too large to allow for tidal circularization, so now it orbits its host from distances spanning 0.16–3.9 au. The maximum difference in planetary equilibrium temperature resulting from this elongated orbit is over 700 K. A simulation of the thermal phase curve of Kepler-1704 b during periastron passage demonstrates that it is a remarkable target for atmospheric characterization from the James Webb Space Telescope, which could potentially also measure the planet’s rotational period as the hot spot from periastron rotates in and out of view. Continued characterization of the Kepler-1704 system promises to refine theories explaining the formation of hot Jupiters and cool giant planets like those in the solar system.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Increasing the Hot‐Electron Driven Hydrogen Evolution Reaction Rate on a Metal‐Free Graphene Electrode

Abstract Recently, it has been shown that a semiconductor–insulator–graphene device can drive the hydrogen evolution reaction (HER) at the graphene surface with a reduced onset potential by injecting hot electrons into graphene. However, the catalytic properties of graphene are limited by the large hydrogen adsorption energy and lack of electrochemically active sites. To address these limitations, a n ‐silicon/insulator/plasma etched graphene device is investigated, where a dry etch process is used to increase the number of active sites on the graphene by creating a greater number of active edge sites, increasing hydrogen adsorption at a given potential. This has been shown to improve the properties of devices with cold electrons. However, here it is shown that this approach can improve the HER rate with hot electrons. The electrons injected into the graphene from the silicon shift the onset potential of HER by as high as ≈0.8 V reaching a current density of 90 mA cm −2 at an overpotential of ‐0.5 V versus RHE. Furthermore, the comparison between device with pristine graphene shows a ≈2X improvement in current density at high overpotentials. This result shows that hot‐electron devices can be improved by modifying the catalytically active sites without metal catalysts.

Chae, Hyun Uk↗
DOE OSTI2020

Stereoscopic detection of hot spots in superfluid 4 He (He II) for accelerator-cavity diagnosis

Superconducting radio-frequency (SRF) cavities cooled by superfluid 4He (He II) are building blocks of many modern particle accelerators due to their high quality factor. However, Joule heating from sub-millimeter surface defects on cavities can lead to cavity quenching, which limits the maximum acceleration gradient of the accelerators. Developing a non-contacting detection technology to accurately locate these surface hot spots is the key to improve the performance of SRF cavities and hence the accelerators. In a recent proof-of-concept experiment, we demonstrated that a molecular tagging velocimetry (MTV) technique based on the tracking of a He molecular tracer line created nearby a surface hot spot in He II can be utilized to locate the hot spot. In order to make this technique practically useful, here we describe our further development of a stereoscopic MTV setup for tracking the tracer line’s motion in three-dimensional (3D) space. We simulate a quench spot by applying a transient voltage pulse to a small heater mounted on a substrate plate. Images of the drifted tracer line, taken with two cameras from orthogonal directions, are used to reconstruct the line profile in 3D space. Here, a new algorithm for analyzing the 3D line profile is developed, which incorporates the finite size effect of the heater. We show that the center location of the heater can be reproduced on the substrate surface with an uncertainty of only a few hundred microns, thereby proving the practicability of this method.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

A suite of neutron time-of-flight detectors to measure hot-spot motion in direct-drive inertial confinement fusion experiments on OMEGA

A suite of six neutron time of flight detectors capable of measuring the primary DT neutron energy spectrum has recently been completed on the OMEGA Laser System. The detectors are positioned along multiple quasi-orthogonal lines of sight (LOS’s) in either a stand-alone, collinear, or antipodal configuration. The collinear detector configuration enables one to measure the neutron velocity along the detector LOS independent of the neutron-production history, while the antipodal detector configuration enables one to directly measure of the hot-spot velocity along the detector axis and Gamow velocity shift due to the plasma ion temperature. Using these six measurements of the primary DT neutron energy spectrum, the neutron-averaged hot-spot velocity and Gamow velocity shift of DT fusion neutrons have been measured in cryogenic experiments on OMEGA for the first time. Finally, the detector suite is operable between DT neutron yields of 1 × 10 13 to 2 × 10 14 with an uncertainty of ~14 km/s in the neutron-averaged hot-spot velocity measurement.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Radiation hot spot formation on UF 6 30B cylinders

The accurate material accountancy of a country's enriched uranium hexafluoride (UF 6 ) stockpiles is imperative to the International Atomic Energy Agency (IAEA) for determining appropriate material safeguards. Uranium hexafluoride is typically stored in large cylinders with enrichment verification typically performed with a NaI gamma detector using the enrichment meter method. This approach for calculating enrichment assumes that the UF 6 is homogeneous inside the cylinder. Here, the measurements and tests presented in this manuscript show that the UF 6 in cylinders left outside in the elements can experience fractionation, leading to inhomogeneity, and subsequent development of radiation hot spots. These hot spot locations can produce errant enrichment measurements. In dark-colored cylinders that experience significant surface heating from the sun, UF 6 sublimates off the cylinder walls, leaving only the uranium daughter products in a horizontal patch (stripe) along the cylinder's midline. This daughter patch is hypothesized to be the source of the radiation hot spots. The patch forms during the summer and tends to decay away during the winter, when solar intensity and temperatures are reduced.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2026

Silyl Hot-Injection Versus Thiocyanate Heat-Up Synthesis of Chalcohalides: Pushing the Size and Composition Envelope

Chalcohalide semiconductors are rapidly gaining traction as stable, biocompatible materials for energy conversion applications. While the solid-state synthesis of bulk chalcohalides is relatively well-developed, the colloidal chemistry of these materials is still in its early stages. Colloidal semiconductors are often advantageous in device fabrication due to the cost effectiveness of solution processing. Thus, we aim to increase the utility of chalcohalides in device fabrication by establishing solution phase chemistry of promising compositions. We show that silyl hot-injection is a versatile and effective method of making colloidal PnChI (Pn = Sb, Bi; Ch = S, Se) and Sn 2 PnS 2 I 3 (Pn = Sb, Bi) chalcohalides of tunable sizes and compositions. Furthermore, we demonstrate the preparation of mixed-pnictide chalcohalides through direct hot-injection and/or postsynthetic cation exchange, the latter being one of the few reported instances in chalcohalides. Additionally, we use the thiocyanate heat-up approach in combination with density functional theory to study halide mixing in quaternary tin chalcohalides. By pushing the limits of each synthetic technique, we have designed more soluble chalcohalides with tunable compositions while also gaining a better understanding of the efficacy of each procedure in respect to thin film and subsequent device fabrication. In addition to size and composition tuning, silyl hot-injection can help facilitate the future development and wide-scale application of chalcohalide-based devices by expanding the selection of solution-processable chalcohalides.

halogens↗