SEARCH · Search NASA

Results for “impedance modelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS2010

Satellite Gravimetry Applied to Drought Monitoring

Near-surface wetness conditions change rapidly with the weather, which limits their usefulness as drought indicators. Deeper stores of water, including root-zone soil wetness and groundwater, portend longer-term weather trends and climate variations, thus they are well suited for quantifying droughts. However, the existing in situ networks for monitoring these variables suffer from significant discontinuities (short records and spatial undersampling), as well as the inherent human and mechanical errors associated with the soil moisture and groundwater observation. Remote sensing is a promising alternative, but standard remote sensors, which measure various wavelengths of light emitted or reflected from Earth's surface and atmosphere, can only directly detect wetness conditions within the first few centimeters of the land s surface. Such sensors include the Advanced Microwave Scanning Radiometer - Earth Observing System (AMSR-E) C-band passive microwave measurement system on the National Aeronautic and Space Administration's (NASA) Aqua satellite, and the combined active and passive L-band microwave system currently under development for NASA's planned Soil Moisture Active Passive (SMAP) satellite mission. These instruments are sensitive to water as deep as the top 2 cm and 5 cm of the soil column, respectively, with the specific depth depending on vegetation cover. Thermal infrared (TIR) imaging has been used to infer water stored in the full root zone, with limitations: auxiliary information including soil grain size is required, the TIR temperature versus soil water content curve becomes flat as wetness increases, and dense vegetation and cloud cover impede measurement. Numerical models of land surface hydrology are another potential solution, but the quality of output from such models is limited by errors in the input data and tradeoffs between model realism and computational efficiency. This chapter is divided into eight sections, the next of which describes the theory behind satellite gravimetry. Following that is a summary of the GRACE mission and how hydrological information is gleaned from its gravity products. The fourth section provides examples of hydrological science enabled by GRACE. The fifth and sixth sections list the challenging aspects of GRACE derived hydrology data and how they are being overcome, including the use of data assimilation. The seventh section describes recent progress in applying GRACE for drought monitoring, including the development of new soil moisture and drought indicator products, and that is followed by a discussion of future prospects in satellite gravimetry based drought monitoring.

Rodell, Matthew↗

NASA NTRS2026

NASA Weather Balloon Demonstration of an Additively Manufactured Antenna

Additive manufacturing (AM) enables low-cost, lightweight, and geometrically flexible antennas for rapid deployment missions. This work reports a left-hand circularly polarized magneto-electric dipole printed on a Radix dielectric with inkjet silver metallization and demonstrated as a process replacement for NASA weather-balloon RF hardware. By combining substrate fabrication and metallization, AM provides value for unrecoverable or field-replaceable systems. A physics based verification workflow links AM-specific material behavior to electromagnetic performance and yields bounded total, radiation, and mismatch efficiencies. Standard surface-impedance and roughness models failed to reproduce the frequency-dependent radiation loss observed in printed inks, underscoring the need for AM-specific conductor parameterization. Mission testing confirmed TDRSS link closure from NASA’s Columbia Scientific Balloon Facility and validated a repeatable print–measure–fly workflow for bounding RF performance and qualifying AM antennas for field use.

Peter Moschetti↗

NASA NTRSDate not supplied

NASA Weather Balloon Demonstration of an Additively Manufactured Antenna

Peter Moschetti↗

NASA NTRS2016

Experimental Evaluation of Equivalent-Fluid Models for Melamine Foam

Melamine foam is a soft porous material commonly used in noise control applications. Many models exist to represent porous materials at various levels of fidelity. This work focuses on rigid frame equivalent fluid models, which represent the foam as a fluid with a complex speed of sound and density. There are several empirical models available to determine these frequency dependent parameters based on an estimate of the material flow resistivity. Alternatively, these properties can be experimentally educed using an impedance tube setup. Since vibroacoustic models are generally sensitive to these properties, this paper assesses the accuracy of several empirical models relative to impedance tube measurements collected with melamine foam samples. Diffuse field sound absorption measurements collected using large test articles in a laboratory are also compared with absorption predictions determined using model-based and measured foam properties. Melamine foam slabs of various thicknesses are considered.

Allen, Albert R.↗

NASA NTRS1991

Impedances of Nickel Electrodes Cycled in Various KOH Concentrations

Impedances were measured of electrodes from boiler-plate cells cycled i n KOH concentrations from 21% to 36%. These cells under accelerated conditions at 80% DOD to failure, defined discharge voltage. Cell life ranged from about 1,000 t o 40 impedances were measured at five voltages corresponding to charge. The results were analyzed using a standard circuit model including a Warburg impedance term. The kinetic resistances and Warburg slopes were greater for those electrodes which had failed earliest. Other circuit models have also been examined. The results are considered indicative but not conclusive, since the cells had been stored after failure for varying lengths of time which is known to affect the impedance. In order to minimize the effects of storage, the electrodes were cycled 10 times before the impedance measurements were taken.

Reid, Margaret A.↗

NASA NTRS1973

A model for the pressure excitation spectrum and acoustic impedance of sound absorbers in the presence of grazing flow.

A unification of the theory of the nonlinear acoustic resistance of Helmholtz resonators including grazing flow is presented. The nonlinear resistance due to grazing flow is considered to be caused by an exciting pressure spectrum produced by the interaction of the grazing flow and the jets flowing from the resonator orifices. With this exciting pressure spectrum the resonator can be treated in the same manner as a resonator without grazing flow but with an exciting acoustic spectrum. One of the important implications of this model is that a multiple-degree-of-freedom resonator can be analyzed with grazing flow. Using the grazing flow pressure spectrum, the nonlinear acoustic resistance can be properly distributed among the several elements of the resonator.

Rice, E. J.↗

NASA NTRS1986

Development of AC impedance methods for evaluating corroding metal surfaces and coatings

In an effort to investigate metal surface corrosion and the breakdown of metal protective coatings the AC Impedance Method was applied to zinc chromate primer coated 2219-T87 aluminum. The model 368-1 AC Impedance Measurement System recently acquired by the MSFC Corrosion Research Branch was used to monitor changing properties of coated aluminum disks immersed in 3.5% NaCl buffered at ph 5.5 over three to four weeks. The DC polarization resistance runs were performed on the same samples. The corrosion system can be represented by an electronic analog called an equivalent circuit that consists of transistors and capacitors in specific arrangements. This equivalent circuit parallels the impedance behavior of the corrosion system during a frequency scan. Values for resistances and capacities that can be assigned in the equivalent circuit following a least squares analysis of the data describe changes that occur on the corroding metal surface and in the protective coating. A suitable equivalent circuit was determined that predicts the correct Bode phase and magnitude for the experimental sample. The DC corrosion current density data are related to equivalent circuit element parameters.

Knockemus, Ward↗

NASA NTRS2014

Improved Broadband Liner Optimization Applied to the Advanced Noise Control Fan

The broadband component of fan noise has grown in relevance with the utilization of increased bypass ratio and advanced fan designs. Thus, while the attenuation of fan tones remains paramount, the ability to simultaneously reduce broadband fan noise levels has become more desirable. This paper describes improvements to a previously established broadband acoustic liner optimization process using the Advanced Noise Control Fan rig as a demonstrator. Specifically, in-duct attenuation predictions with a statistical source model are used to obtain optimum impedance spectra over the conditions of interest. The predicted optimum impedance information is then used with acoustic liner modeling tools to design liners aimed at producing impedance spectra that most closely match the predicted optimum values. Design selection is based on an acceptance criterion that provides the ability to apply increased weighting to specific frequencies and/or operating conditions. Constant-depth, double-degree of freedom and variable-depth, multi-degree of freedom designs are carried through design, fabrication, and testing to validate the efficacy of the design process. Results illustrate the value of the design process in concurrently evaluating the relative costs/benefits of these liner designs. This study also provides an application for demonstrating the integrated use of duct acoustic propagation/radiation and liner modeling tools in the design and evaluation of novel broadband liner concepts for complex engine configurations.

Nark, Douglas M.↗

NASA NTRS2022

Space Induced Discharge Model to Be Used on Interface Circuit Vulnerability Assessment

Charging can occur in space due to plasma and high energy particles. Charging is especially severe in certain earth orbits such as geostationary orbit, medium earth orbit and highly inclined orbit. A spacecraft that travels to other planets such as Jupiter also encounters high level of charging due to Jupiter’s radiation belt. The major concern for spacecraft operation due to charging is the survival of sensitive electrical circuits. Dielectrics and floating metal can charge up and discharge onto interface circuits. The electrical circuits need to be evaluated for survival from the electrostatic-discharge (ESD) threat. Both ESD induced upset and damage need to be assessed. The interface circuits are often located inside a shielded unit in the spacecraft structure or a shielded vault with sufficient radiation shielding to avoid surface and internal charging. The materials external to the highly shielded area can charge up and discharge onto wires that can directly dissipate the ESD onto the interface circuits. Figure 1 shows a possible discharge mechanism onto the interfacing circuits. If the wire has an external shield or a coaxial line, some or most of the discharge can flow on the shield to chassis ground. There is always coupling from external discharge. If the wire has no shield, the discharge flows onto the interface circuit. Fig. 1 Possible discharge paths onto the interface circuits. The purpose of this article is to address how to model the ESD threat to be used as the discharge source onto the interface circuit based on the electron beam test data. Different models are needed for different impedances associated with the interface circuits. Once those models are derived, one needs to analyze the interface circuit with the corresponding model using an electrical simulation tool. Then, the circuit’s front-end components can be assessed for damage and upset. Upset is highly dependent on the circuit operation and system requirements, and thus it is not addressed any further. Damage of electrical parts is often rated under Human-Body-Model (HBM) ESD. One can utilize this industry-wide available information to assess the damage vulnerability due to space discharges. However, the HBM waveform does not always match the discharge waveform. To estimate the damage vulnerability of the circuit and set margin, one needs to compare the equivalent energy delivered to the victim between a HBM discharge and the results from an ESD source model based on actual discharges. This paper presents such a comparison for a few select cases.

Xie, Julie↗

NASA NTRSDate not supplied

Assessment of Acoustic Behavior for Perforate-Over-Large-Cell Liners

This study explores the effects of increasing the cell size for large-cell acoustic liners. Tests are conducted in the NASA Langley Grazing Flow Impedance Tube to evaluate liners with increasingly larger cell dimensions (up to 2” x 4” cross-section). Conventional impedance eduction confirms that liners with 2” x 3” cells (or larger) must be evaluated using nonlocally reacting assumptions. In addition, due to the sound propagation within cavities, the liners must be modeled using higher fidelity techniques. Thus, grazing flow duct and acoustic liner are modeled simultaneously using finite element methods. The facesheet is modeled using a transfer impedance, while the rest of the domain is modeled using the convected Helmholtz equation. The acoustic pressures predicted are shown to compare favorably with those measured in the Grazing Flow Impedance Tube.

large diameter↗

NASA NTRS2012

Broadband Liner Optimization for the Source Diagnostic Test Fan

The broadband component of fan noise has grown in relevance with the utilization of increased bypass ratio and advanced fan designs. Thus, while the attenuation of fan tones remains paramount, the ability to simultaneously reduce broadband fan noise levels has become more appealing. This paper describes a broadband acoustic liner optimization study for the scale model Source Diagnostic Test fan. Specifically, in-duct attenuation predictions with a statistical fan source model are used to obtain optimum impedance spectra over a number of flow conditions for three liner locations in the bypass duct. The predicted optimum impedance information is then used with acoustic liner modeling tools to design liners aimed at producing impedance spectra that most closely match the predicted optimum values. Design selection is based on an acceptance criterion that provides the ability to apply increased weighting to specific frequencies and/or operating conditions. Typical tonal liner designs targeting single frequencies at one operating condition are first produced to provide baseline performance information. These are followed by multiple broadband design approaches culminating in a broadband liner targeting the full range of frequencies and operating conditions. The broadband liner is found to satisfy the optimum impedance objectives much better than the tonal liner designs. In addition, the broadband liner is found to provide better attenuation than the tonal designs over the full range of frequencies and operating conditions considered. Thus, the current study successfully establishes a process for the initial design and evaluation of novel broadband liner concepts for complex engine configurations.

Nark, Douglas M.↗

NASA NTRS2016

Further Development and Assessment of a Broadband Liner Optimization Process

The utilization of advanced fan designs (including higher bypass ratios) and shorter engine nacelles has highlighted a need for increased fan noise reduction over a broader frequency range. Thus, improved broadband liner designs must account for these constraints and, where applicable, take advantage of advanced manufacturing techniques that have opened new possibilities for novel configurations. This work focuses on the use of an established broadband acoustic liner optimization process to design a variable-depth, multi-degree of freedom liner for a high speed fan. Specifically, in-duct attenuation predictions with a statistical source model are used to obtain optimum impedance spectra over the conditions of interest. The predicted optimum impedance information is then used with acoustic liner modeling tools to design a liner aimed at producing impedance spectra that most closely match the predicted optimum values. The multi-degree of freedom design is carried through design, fabrication, and testing. In-duct attenuation predictions compare well with measured data and the multi-degree of freedom liner is shown to outperform a more conventional liner over a range of flow conditions. These promising results provide further confidence in the design tool, as well as the enhancements made to the overall design process.

Nark, Douglas M.↗

NASA NTRSDate not supplied

Benchmark Data for Evaluation of NASA Impedance Eduction Methods

Results achieved with three acoustic liner configurations are used to evaluate the effects of recent modifications to the NASA Normal Incidence Tube and Grazing Flow Impedance Tube. These include a calibration liner, a wire mesh liner, and a perforate liner. The effects of source type, source level, and mean flow Mach number on the impedances educed with these liners are explored. Existing models are used to predict the impedance for each test condition and are compared with educed impedance spectra to determine their validity. The results suggest that educed impedances are similar for either a stepped sine or swept sine source. The predicted models are acceptable for the perforate liner and are quite good for the calibration and wire mesh liners.

acoustic↗

NASA NTRSDate not supplied

Benchmark Data for Evaluation of NASA Impedance Eduction Methods

Results achieved with three acoustic liner configurations are used to evaluate the effects of recent modifications to the NASA Normal Incidence Tube and Grazing Flow Impedance Tube. These include a calibration liner, a wire mesh liner, and a perforate liner. The effects of source type, source level, and mean flow Mach number on the impedances educed with these liners are explored. Existing models are used to predict the impedance for each test condition, and are compared with educed impedance spectra to determine their validity. The results suggest that educed impedances are similar for either a stepped sine or swept sine source. The predicted models are acceptable for the perforate liner, and are quite good for the calibration and wire mesh liners.

acoustic↗

NASA NTRS1973

A model for the pressure excitation spectrum and acoustic impedance of sound absorbers in the presence of grazing flow

The acoustic impedance of sound absorbers in the presence of grazing flow is essential information when analyzing sound propagation within ducts. A unification of the theory of the nonlinear acoustic resistance of Helmholtz resonators including grazing flow is presented. The nonlinear resistance due to grazing flow is considered to be caused by an exciting pressure spectrum produced by the interaction of the grazing flow and the jets flowing from the resonator orifices. With this exciting pressure spectrum the resonator can be treated in the same manner as a resonator without grazing flow but with an exciting acoustic spectrum.

Rice, E. J.↗

NASA NTRS2000

Modeling of Horns for Sonic/Ultrasonic Applications

JPL has a requirement for telerobotic tools for planetary sample acquisition, which require low power and have the ability to work in harsh environments. We are currently investigating the possibility of using ultrasonic horns to develop a family of ultrasonic tools for these environments. In an effort to determine control parameters a one-dimensional Mason's model for a stepped ultrasonic horn assembly was developed which includes the effects of mechanical and electrical losses in the piezoelectric material and acoustic elements. The model is separated into three regions; the piezoelectric stack including stress bolt the backing layer and the horn. The model is found to predict the impedance data of the horn assembly very accurately up to the first coupled (radial) resonance. The model also allows for the calculation of the velocity and force and power delivered to each acoustic element. FEM modeling and accelerometer data from the horn tip were used to corroborate the model. The difficulties associated with modeling the load impedance of various devices will be discussed and current directions noted.

Sherrit, Stewart↗

NASA NTRS1991

Estimating radiated power from a conducting tethered satellite system

In anticipation of the upcoming TSS-1 experiment, theoretical calculations are made of radiated power from a conducting tethered satellite system. The radiation results from the steady motion of the system through the ionospheric plasma and it is stimulated by collection and emission of charge by the noninsulated surfaces of the tethered end connectors. A model of the current system is developed which incorporates the tether wire, satellite surfaces, and sheath currents. The radiation impedance of the current model is calculated using the previously developed theory of Barnett and Olbert (1986). The results confirm the low-frequency Alfven wave description with a predicted radiation impedance of a few tenths of an ohm in the Alven wave limit. Calculations are also made in the lower hybrid and whistler wave band. A larger impedance of about 13 ohm is found for the frequency range 5-50 kHz. By estimating the passive ion current drawn by the system a prediction of the total radiated power is also made. The result of 0.38 mW raises the question of whether or not wave emissions from a passive current collecting system may be detectable by either ground- or space-based platforms.

Donohue, D. J.↗

NASA NTRS1996

Time-Domain Impedance Boundary Conditions for Computational Aeroacoustics

It is an accepted practice in aeroacoustics to characterize the properties of an acoustically treated surface by a quantity known as impedance. Impedance is a complex quantity. As such, it is designed primarily for frequency-domain analysis. Time-domain boundary conditions that are the equivalent of the frequency-domain impedance boundary condition are proposed. Both single frequency and model broadband time-domain impedance boundary conditions are provided. It is shown that the proposed boundary conditions, together with the linearized Euler equations, form well-posed initial boundary value problems. Unlike ill-posed problems, they are free from spurious instabilities that would render time-marching computational solutions impossible.

Tam, Christopher K. W.↗