Search NASA⌕ Search

SEARCH · Search NASA

Results for “interfacial characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

A mild calcium carbonate treatment improves moisture resistance and mechanical/interfacial properties of jute and hemp fibers

Natural fibers are attractive, sustainable reinforcements, but often exhibit high moisture uptake and weak bonding with polymer matrices. In this study, jute and hemp were treated by immersion in aqueous calcium carbonate (CaCO3) suspensions (10–40?wt.%, 1.5?h, room temperature) and were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), moisture sorption testing, single-fiber tensile testing, and bundle pull-out testing. SEM showed granular CaCO3 deposition on fiber surfaces, with particulates bridging surface voids and microcracks. At 40 wt.% CaCO3, equilibrium moisture uptake decreased to ~5% (hemp) and ~3% (jute), while tensile strength increased to ~904 MPa (hemp) and ~960 MPa (jute). Apparent interfacial shear strength from pull-out testing increased up to ~1.35 MPa (hemp) and ~0.56 MPa (jute). These results indicate that CaCO3 deposition is a mild, scalable surface treatment that improves moisture resistance, fiber tensile strength, and interfacial load transfer relevant to semi-structural composite applications, including interior and secondary automotive components.

Calcium carbonate treatment↗
DOE OSTI2024

Direct Imaging of Asymmetric Interfaces and Electrostatic Potentials inside a Hafnia–Zirconia Ferroelectric Nanocapacitor

In hafnia-based thin-film ferroelectric devices, chemical phenomena during growth and processing, such as oxygen vacancy formation and interfacial reactions, appear to strongly affect device performance. However, the correlation between the structure, chemistry, and electrical potentials at the nanoscale in these devices is not fully known, making it difficult to understand their influence on device properties. Here, we directly image the composition and electrostatic potential with nanometer resolution in the cross section of a nanocrystalline W/Hf 0.5 Zr 0.5 O 2−δ (HZO)/W ferroelectric capacitor using multimodal electron microscopy. This reveals a 1.4 nm wide tungsten suboxide interfacial layer formed at the bottom interface during fabrication, which introduces a potential dip and leads to asymmetric switching fields. Additionally, we compare the measured potentials to DFT calculations and find it is nearly 3 V lower than expected in the HZO, which appears to be caused by oxygen vacancies and a resulting negative built-in potential. In conclusion, these chemical and electrostatic details are important to characterize and tune to achieve high-performance ferroelectric devices.

Defects in solids↗
DOE OSTI2025

Tuning Kinetic Inductance with Doping in Superconducting Electron Gases at the KTaO 3 (111) Interface

We used coplanar waveguide resonators fabricated from the two-dimensional superconductor formed at KTaO 3 (111) interfaces to characterize the superconductor’s sheet kinetic inductance L K/□ . Upon varying the carrier density, in samples with T c ranging from 0.62 to 1.81 K, we can tune L K/□ between 1.88 and 7.42 nH/□ at the lowest temperatures, exceeding the highest values reported for granular aluminum films. The temperature dependence of L K/□ is consistent with a superconducting gap without nodes. The high L K/□ of superconducting KTaO 3 (111) interfacial electron gases combined with the high dielectric constant of KTaO 3 results in resonators with exceedingly low phase velocities (“slow light”) and small mode volumes. In addition, superconducting KTaO 3 (111) interfacial electron gases are robust in magnetic fields well above a Tesla. In conclusion, these features can enable unique device applications in superconducting electronics and quantum information science.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Chemical Compensation Challenges in Processing Antiferroelectric PbZrO 3 Thin Films

The electric field-induced antipolar-to-polar phase transition in antiferroelectric materials is accompanied by large changes in the structural and functional response, making them attractive for many applications ranging from pulsed energy capacitors to high-strain-high (blocking-)force actuators, solid-state heating and cooling systems, and optoelectronic devices. PbZrO 3 , as an end member of the PZT, (x)PbZr 1–x Ti x O 3 , solid solution, has been the subject of many studies. However, processing of perovskite PbZrO 3 is extremely challenging due to phase instabilities induced by Pb loss at the temperatures necessary for perovskite crystallization. Here, we discuss the challenges associated with Pb loss, as well as its compensation through bulk Pb overstoichiometry and interfacial PbO additions, in chemical solution processed, highly oriented PbZrO 3 thin films. For both 042 o - and 001 o -oriented (o-orthorhombic distortion) PbZrO 3 thin films, the crystallization interfaces are the most important contributors to Pb loss and off-stoichiometric outcomes, and no single approach was sufficient to address these challenges. Pb-rich and Pb-deficient nonperovskite phases including ZrO x were only observable through microscopic characterization, and X-ray diffraction alone could not rule out the presence of such secondary phases. “Ideal” macroscopic antiferroelectric polarization-electric field double hysteresis curves were observed despite (at times) the large presence of secondary phases. However, reduced saturation polarization and increased phase transition electric fields were observed concomitantly with the presence of secondary phase(s) and tentatively assigned to the voltage drop across the ZrO x nanocrystals. Based on these results, it is imperative that the presence of secondary phases always be addressed (beyond X-ray diffraction spectra) in order to correctly evaluate the properties of antiferroelectric films.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Evaluating the bond strength and fracture mechanisms of cold-sprayed zinc coating on AZ91 magnesium substrate via a combined experimental and computational approach

Magnesium (Mg) alloys are ideal candidates for automotive applications due to their high strength to weight ratio, castability, recyclability etc., however, they lack corrosion and oxidation resistance. Solid-state deposition techniques, such as cold spray, have been demonstrated to enhance their corrosion resistance as it relies on the severe plastic deformation of powder particles upon impact with the substrate to form a metallurgical bond with the substrate and within the coating. At cold sprayed interfaces, a heterogeneous microstructure is formed that includes some porosity, oxides and intermetallics which can significantly affect coating performance. Thus, establishing a direct correlation between the interface microstructure and its properties can aid in designing optimal cold spray parameters. In this study, we investigated the microstructure and mechanical properties of a zinc (Zn) coating deposited on a high pressure die cast (HPDC) AZ91 Mg substrate via high resolution scanning transmission electron microscopy, in situ micro-tensile testing, and finite element method (FEM) modeling. Micro-tensile pillars fabricated using the plasma focused ion beam (PFIB) successfully isolates the coating-substrate interface within the gauge length. The average bond strength of Zn-Mg interface was determined to be ∼140 MPa with failure occurring partially at the interface and mostly into the coatings. A detailed microstructural characterization revealed evidence of a strong metallurgical bonding at the Zn-Mg interface and formation of the C14 MgZn 2 laves phase interlayer resulting in a mixed mode of fracture during the micro-tensile experiments. FEM modeling reveals the stress distribution along the interfaces and suggests that a MgZn 2 layer thickness between 200–400 nm is optimum to increase the bond strength and minimize the triaxiality. Such a site-specific interfacial analysis with correlative computational modeling provides crucial insight into the overall performance of cold spray interfaces.

Bond strength↗
DOE OSTI2024

Direct quantification of ion composition and mobility in organic mixed ionic-electronic conductors

Ion transport in organic mixed ionic-electronic conductors (OMIECs) is crucial due to its direct impact on device response time and operating mechanisms but is often assessed indirectly or necessitates extra assumptions. Operando x-ray fluorescence (XRF) is a powerful, direct probe for elemental characterization of bulk OMIECs and was used to directly quantify ion composition and mobility in a model OMIEC, poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonate) (PEDOT:PSS), during device operation. The first cycle revealed slow electrowetting and cation-proton exchange. Subsequent cycles showed rapid response with minor cation fluctuation (~5%). Comparison with optical-tracked electrochromic fronts revealed mesoscale structure–dependent proton transport. The calculated effective ion mobility demonstrated thickness-dependent behavior, emphasizing an interfacial ion transport pathway with a higher mobile ion density. The decoupling of interfacial effects on bulk ion mobility and the decoupling of cation and proton migration elucidate ion transport in conventional and emerging OMIEC-based devices and has broader implications for other ionic conductors writ large.

42 ENGINEERING↗
DOE OSTI2024

Unraveling the multi-step crystallization mechanism of polytetrafluoroethylene, modified polytetrafluoroethylene, and their nanocomposites with boron nitride nanobarbs: Experimental insights and theoretical analysis

The non-isothermal crystallization behavior and kinetics of polytetrafluoroethylene (PTFE) composites with boron nitride nanobarb (BNNB), a new generation nanostructure with unique surface morphology and mechanical “barbs” have been analyzed, understanding these properties is essential for their high-end applications as thermal interface materials (TIM) for microwave, 5G and microelectronic devices. The analysis of the crystallization parameters includes crystallization onset, peak and end temperatures, crystallization half-life and overall crystallinity of PTFE, modified PTFE and their BNNB composites. The results were further analyzed using theoretical models such as the combined Avrami-Ozawa model. It was found that BNNB supports crystallization in the modified PTFE but shows minimal effect on the crystallization of PTFE. Due to the limitation of the classical theoretical models used above in fully characterizing the multi-step crystallization process of PTFE, an in-depth analysis using the model-free advanced isoconversional computation was used to characterize the PTFE crystallization based on the evolution of activation energy with fractional crystallinity and for the first time with temperature. Three kinetic regions were identified in the crystallization mechanism. Here, this study investigated the molecular organization and microstructural evolution of PTFE, modified PTFE and their composites during non-isothermal crystallization using advanced X-ray scattering measurements. An insight into the changes undergone by the material's microstructural units including crystallite size and morphology, lamellar thickness and lamellar interfacial layer thickness, and crystallographic phase dynamics during non-isothermal cooling from the melt, was provided here in this work. The effect of copolymer modification of PTFE and the inclusion of pristine and functionalized BNNB (a thermally conductive and electrically insulating ceramic) are both new investigations that provide valuable knowledge for the development of materials with strong matrix-nanofiller interaction and guidance for optimizing sintering and cooling cycles, two key steps in PTFE processing that largely affect the material microstructural features. Overall, the result of the three-part investigation demonstrates that BNNB supports crystallization in the modified PTFE up to 20 wt% concentration and at low and high cooling rates typically used in the industrial processing of PTFE.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Low-Temperature Catalyst Redispersion: A Route to Enhanced Stability of Supported Metal Catalysts?

Sintering poses a significant challenge to achieving the long-term stability of supported metal catalysts under reaction conditions. Here, in this study, we report a low-temperature catalyst redispersion mechanism, in which platinum single atoms, which aggregate into nanoparticles under Reverse Water Gas Shift (RWGS) conditions at elevated temperatures, fragment into atomically dispersed species upon cooling. Using multimodal operando characterization combined with first-principles theoretical modeling, we track the structural evolution of Pt single atoms supported on ceria nanodomes, deposited either on ceria or ceria–titania mixed oxides. We find that fragmentation is more pronounced when cooling occurs under RWGS conditions compared to CO alone, owing to a synergistic interplay of the effects of H 2 , CO 2 , and CO. The support architecture has a strong influence on the extent of redispersion: while CO alone induces fragmentation on ceria, interfacial confinement and vacancy pinning at the ceria–titania interface suppress restructuring. In contrast, RWGS conditions overcome these barriers, enabling redispersion across both supports. These findings point toward a pathway for catalyst stabilization via reaction-induced redispersion under mild conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Understanding particle size effect on fast-charging behavior of graphite anode using ultra-thin-layer electrodes

Extreme fast charging (≤ 15 min) of lithium-ion batteries is highly desirable to accelerate mass-market adoption of electric vehicles. However, significant capacity fading, as well as safety issues due to the lithium plating caused by the fast charging rate, limit its implementation. In this study, we investigated the fast-charging capability of graphite materials with various particle sizes. To eliminate the Li + ion concentration gradient effect across the thickness of the electrode, ultra-thin-layer graphite electrodes were developed to investigate the "real" fast-charging capability of graphite at the particle level. Electrochemical assessments as well as microscopic characterizations revealed that smaller particles exhibited superior fast-charging performance, featuring enhanced capacity reversibility, faster charging rate, and less lithium plating under the same fast-charging conditions. It is shown that small-particle graphite (mean radius of 3.3 μm) could withstand a 4C charge (to 80 % state-of-charge) without plating, with minimal plating occurring at 6C. Thicker particles exhibited plating at lower C-rates. Since the experimental data could not directly explain whether intra-particle diffusion limitations or interfacial reaction limitations dominated the plating mechanism, the pseudo-2-dimensional model was used to evaluate the most likely plating mechanism. The model suggested that particle-level diffusion is the dominant mechanism contributing to plating at high rates. Finally, this work provides comprehensive insights into the particle size effects on fast-charging capability, offering a better understanding of fast-charging behavior and valuable guidance for designing optimal electrode architecture for high-rate lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2026

High pressure effects on EBC systems in high temperature environments

Environmental barrier coatings (EBCs) are designed to protect SiCfiber/SiCmatrix ceramic matrix composites (CMCs) in turbine engines by mitigating wear in high-temperature water vapor environments. The failure of EBCs is frequently attributed to the accelerated oxidation of the silicon bond coating layer when exposed to high-temperature steam, leading to the formation of a thickened thermally grown oxide (TGO). TGO growth increases interfacial stress, weakens adhesion, and results in coating spallation. Understanding the impact of high-temperature oxidation of EBC systems is essential for developing accurate lifespan models for turbine components, although pressurized oxidation testing is extremely sparse in the open literature. In this work, oxidation tests were performed on rare earth silicate EBCs coated onto SiC substrates under increased pressure conditions. The coated specimens were tested at 1100°C, 1200°C, and 1300°C at both 1 atm and 10 atm total pressure in steam environments. Subsequent characterization focused on the microstructural evolution of the EBC/Si/SiC system. The experimental findings indicated that TGO behavior is dependent on high-pressure conditions, with elevated pressure leading to an increase in oxide scale thickness and modifications in its morphology.

Ardrey, Kristyn [ORNL] (ORCID:0000000184407796)↗
DOE OSTI2025

Functional group activation and coupling agent migration induced by plasma treatment in adhesive for enhanced toughness of metal-composite joints

Commercial adhesive paste was additionally activated using low-power oxygen plasma with different plasma exposure durations to investigate its interfacial bonding contribution in adhesively-bonded Aural-5/CFRP-PA6 double cantilever beam (DCB) joints with plasma-treated adherends. The plasma-treated adhesive showed enhanced functional peak intensities in Fourier transfer infrared spectroscopy (FTIR) as plasma exposure time was increased, and some degree of oxidation was also detected via X-ray photoelectron spectroscopy (XPS). A small molecule, dicyandiamde (coupling agent) in adhesive was migrated to adhesive layer, where double concentration of coupling agent was detected after 10 minutes of plasma treatment. As a result, characterization of the adhesive/CFRP-PA6 interface after DCB fracture showed additional chemical bonds formed through amine-initiated epoxy ring opening polymerization, as well as amide bonds and ester bonds. In conclusion, these additional bonds at the adhesive/CFRP-PA6 interfaces led to significantly increased failure extensions and fracture energies of the joints as the plasma exposure time on the adhesive increased, compared to the joints with plasma-treated adherends but non-plasma-treated adhesive as commonly seen in the literature.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Digital Twin for Chemical Science (DTCS) v0.01

Directly visualizing the trajectories of chemistry can unravel novel insights into the behavior of catalysts, gas phase reactions, photo-induced dynamics, and building blocks for quantum information processing. The ability of explicitly identifying, tracking, and tagging the exchange of matter, hence the annihilation and creation of new chemical species, can be best realized through a close coupling of theory and experiment. While the synchrotron-based characterization facilities propelled rapidly in its hardware, providing higher brightness, better resolution, and more precision, the software infrastructure is lagging. We developed DTCS (Digital Twin for Chemical Science) v.01, a central platform that faithfully mimics advanced instrumentations in Scientific User Facilities, by solving a variety of technical challenges in data acquisition, analysis, and model-driven interpretation. Rooted in physics and accelerated by AI, we validated this concept by direct comparison with precise experimental X-ray Photoelectron Spectroscopy (XPS) observations using a ubiquitous metal-water interfacial scenario, i.e., Ag/H2O as our main narrative. The DTCS v.01 input mirrors how the bench chemists work, with the output directly linked to the end station computer, thereby providing a user-friendly, knowledge-driven, and accessible user experience with mechanistic insights standardized in a way that are ready to be published, versioned, and transferred flexibly.

Qian, Jin↗
DOE OSTI2026

Mechanistic transition of stainless steel 304L corrosion in MgCl 2 phase change material under thermal cycling

Magnesium chloride (MgCl 2 )-based molten salt phase change materials (PCMs) are promising candidates for thermal energy storage (TES) owing to their advantageous thermophysical properties, however, their high corrosivity in the molten state limits material compatibility. In this study, the corrosion behavior of 304?L stainless steel (SS304L) exposed to MgCl2 PCM was investigated as a function of thermal cycling (up to 9000 cycles) relevant to PCM-based TES systems. Microstructural changes and elemental redistribution at the alloy-salt interface under thermal cycling conditions were characterized using synchrotron-based X-ray fluorescence (XRF) and scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM-EDS). Results show that corrosion is governed by selective Cr-dissolution and elemental diffusion near the interface and grain boundaries. A clear transition in the dominant corrosion mechanism is observed with increasing thermal cycles. Surface corrosion is the dominant mechanism up to 1000 cycles, whereas intergranular corrosion becomes the primary degradation mode beyond 2000 cycles. These mechanistic changes are interpreted in terms of evolving interfacial chemistry, microstructure and the diffusion-driven redistribution of alloying elements.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Indium Tin-Doped Oxide Interactions with Solvent Radiolysis Products

Transparent conductive oxides (TCOs), such as indium tin-doped oxide (ITO), are ubiquitous as components of electronics and are ideal electrode substrates for catalysis, energy transformation reactions, and energy storage applications. Recently, researchers have recognized their effectiveness as electrode materials for manipulating actinide oxidation states in solution. Despite their popularity as electrode materials, prior studies focused extensively on the direct radiolysis of TCO materials in air and rarely examined these effects within a solution, limiting our fundamental understanding of the interactions between solvent radiolysis products and these substrates in high radiation environments. Here, in this study, we characterize the effects of solvent radiolysis products—arising from the gamma irradiation of water, aqueous nitric acid solutions, and n-dodecane—on the composition, surface speciation, and band structure of ITO thin films on a glass substrate as a function of absorbed dose using UV-visible spectroscopy, scanning electron microscopy, photoelectrochemistry, and X-ray photoelectron spectroscopy. Our work demonstrates that mesoporous thin film electrodes of ITO exposed to gamma radiation in each solvent accumulate defects and exhibit solvent and dose dependent changes to their surface and interfacial properties. These electrodes maintain their electrochemical function and improve their photoelectrochemical performance up to at least 100 kGy of accumulated gamma dose, confirming their utility in solvents exposed to ionizing radiation fields.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Evaluation of high-temperature properties of binary, eutectic Ni-X alloys (X = B, Ca, Ce, La, Y, Zr)

We investigated the high-temperature behavior of binary eutectic nickel-base alloys with low-solubility elements, towards developing alloys with new combinations of structural and functional (e.g. thermal or corrosion) properties. Based on thermodynamic screening, we cast binary near-eutectic Ni-B, Ni-Ca, Ni-Ce, Ni-La, Ni-Y, and Ni-Zr alloys and characterized their microstructure and high-temperature properties. All alloys (except Ni-Ca) contain a fine eutectic microstructure, containing submicron alternating lamellae of γ-Ni and continuous intermetallic phases. The eutectic microstructure did not significantly coarsen at 700°C (except for Ni-B), but measurably coarsened in all alloys at 900°C, most quickly in Ni-B, followed by Ni-Ce, Ni-La, Ni-Y, and Ni-Zr. Coarsening in these alloys occurs by fault migration; diffusion within the intermetallic, and its interfacial energy, likely influence coarsening kinetics. At room-temperature, all alloys possess negligible ductility due to the continuous, brittle intermetallic. At 700 and 900°C, the Ni-Zr alloy showed the best combination of strength and ductility. Oxidation experiments at 900°C on Ni-Zr and Ni-Ce revealed heavy internal oxidation of the continuous intermetallic phase. Overall, the Ni-Zr alloy showed good high-temperature coarsening resistance and strength, though ductility and oxidation resistance require improvement for use in structural applications. Possible routes for improving alloy properties via additive manufacturing are discussed.

Ekaputra, Clement [ORNL] (ORCID:0000000307166479)↗
DOE OSTI2025

Heavy boron doping effects on biaxially tensile strained germanium (>1.5%) investigated via structural characterization, effective lifetime assessment and atomistic modeling

Highly tensile strained germanium (ε-Ge) represents an essential material system for emerging electronic and photonics applications. Moreover, adjusting the doping levels to moderate or high concentrations can effectively tailor the properties of ε-Ge for specific applications. This article combines experimental characterization with a theoretical framework to examine the effects of heavy elemental boron (B) doping on pseudomorphic sub-50 nm ε-Ge. High resolution X-ray diffractometry is used to validate tensile strain levels of 1.53% and 1.68% in Ge epilayers, surpassing the indirect-to-direct band gap crossover point at ∼1.5% biaxial tensile strain. Cross-sectional transmission electron microscopy revealed visual evidence of stacking faults and surface roughening in 1.68% ε-Ge, although a coherent and abrupt Ge/III–V heterointerface is observed, devoid of interfacial misfit dislocations. Effective lifetime measurements demonstrated approximately twofold enhancement in 1.53% B-doped ε-Ge (N B ∼7 × 10 19 cm −3 ) compared to its unstrained B-doped counterpart, while no such improvement was observed in 1.68% B-doped ε-Ge. This lack of enhancement is attributed to the presence of stacking faults and surface roughness within the ε-Ge epilayer. Through density functional theory calculations, we independently demonstrate that substitutional B atoms induce local deformation of Ge–Ge bonds in both unstrained Ge and ε-Ge epilayers, resulting in an additive tensile strain. This phenomenon could potentially lead to dynamic reduction and overcoming of the critical layer thickness for the system, facilitating the nucleation and subsequent glide of 90° leading Shockley partial dislocations, thereby generating stacking faults. In essence, these findings establish an upper limit on the B-doping concentration that can be achieved in highly ε-Ge epilayers, and collectively, offer valuable insights into the significance of heavy doping in Ge-based heterostructures. As such, this study delineates a fundamental constraint for integrating heavily doped ε-Ge in high-performance optoelectronic systems, necessitating precise strain-doping co-optimization to avoid performance degradation.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

3D Printing of Cement-Based Materials Using Seawater for Simulated Marine Environments

Global demand for adaptable and rapidly deployable construction solutions in offshore, coastal, and fluvial environments continues to rise, driven by pressing needs to develop energy platforms, improve coastal resilience, and support emergency response in the face of natural disasters. Increased investment in human-made coastal infrastructure, such as piers, support structures for power lines, offshore wind farms, and seawall protection systems, further underscores this trend. This study investigates the development of printable concrete mixtures for underwater environments using seawater as a replacement for freshwater, using a 3D printing syringe-based extrusion system. The effect of seawater addition and the printing medium (in air vs. underwater) was assessed via rheological and mechanical performance characterization. The results indicate rheological properties are favorable for seawater adoption by producing mixtures with higher yield stress and viscosity with the same levels of admixtures used for freshwater. Seawater-based mixtures demonstrated superior dimensional stability compared to freshwater counterparts, maintaining cross-sectional geometry, while compressive strength results showed no statistical differences between in-air and underwater samples. However, flexural strength was significantly influenced by geometry and printing medium. These findings establish critical rheological parameters for printable underwater mixtures and highlight the need for optimized curing strategies and layer bonding techniques to improve interfacial strength in underwater 3D printing applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

From Pollutant Removal to Renewable Energy: MoS2-Enhanced P25-Graphene Photocatalysts for Malathion Degradation and H2 Evolution

The widespread presence of pesticides—especially malathion—in aquatic environments presents a major obstacle to conventional remediation strategies, while the ongoing global energy crisis underscores the urgency of developing renewable energy sources such as hydrogen. In this context, photocatalytic water splitting emerges as a promising approach, though its practical application remains limited by poor charge carrier dynamics and insufficient visible-light utilization. Herein, we report the design and evaluation of a series of TiO2-based ternary nanocomposites comprising commercial P25 TiO2, reduced graphene oxide (rGO), and molybdenum disulfide (MoS2), with MoS2 loadings ranging from 1% to 10% by weight. The photocatalysts were fabricated via a two-step method: hydrothermal integration of rGO into P25 followed by solution-phase self-assembly of exfoliated MoS2 nanosheets. The composites were systematically characterized using X-ray diffraction (XRD), Raman spectroscopy, transmission electron microscopy (TEM), UV-Vis diffuse reflectance spectroscopy (DRS), and photoluminescence (PL) spectroscopy. Photocatalytic activity was assessed through two key applications: the degradation of malathion (20 mg/L) under simulated solar irradiation and hydrogen evolution from water in the presence of sacrificial agents. Quantification was performed using UV-Vis spectroscopy, gas chromatography–mass spectrometry (GC-MS), and thermal conductivity detection (GC-TCD). Results showed that the integration of rGO significantly enhanced surface area and charge mobility, while MoS2 served as an effective co-catalyst, promoting interfacial charge separation and acting as an active site for hydrogen evolution. Nearly complete malathion degradation (~100%) was achieved within two hours, and hydrogen production reached up to 6000 µmol g−1 h−1 under optimal MoS2 loading. Notably, photocatalytic performance declined with higher MoS2 content due to recombination effects. Overall, this work demonstrates the synergistic enhancement provided by rGO and MoS2 in a stable P25-based system and underscores the viability of such ternary nanocomposites for addressing both environmental remediation and sustainable energy conversion challenges.

Chemistry↗